用于纳米粒子检测的双环谐振器（英文）

设计了一种可以探测单个纳米粒子的光学传感器结构,该结构由双环、双环间耦合区的通孔和直波导构成,并引入了Fano效应,进一步增强了粒子在光场中出现时的光耦合场变化.当纳米粒子穿过两个微环间的通孔时,其耦合系数和输出端的光强均发生变化,提出了一种基于双环谐振器结构的高精度耦合系数传感方法,通过检测双环谐振器耦合系数和输出端光强的变化对单体纳米粒子进行精确检测和计数.理论计算结果表明,在损耗为1dB/cm的情况下,与单环结构相比,双环结构的灵敏度提升了两个数量级.该双环结构在减小波导损耗的同时有效提升了检测灵敏度.     

耦合谐振器光波导旋转传感的相位灵敏度

利用光学谐振器结构的色散可提高旋转传感的灵敏度, 耦合谐振器光波导可实现强色散, 本文利用传输矩阵理论, 研究耦合谐振器光波导旋转传感的相位灵敏度, 讨论谐振器布局和波导参数对相位灵敏度的影响, 结果表明波导的相位曲线和相位灵敏度依赖于波导中谐振器的布局, 谐振器数量和耦合系数不仅会影响波导旋转传感相位灵敏度曲线峰值的数量和带宽, 还会影响相位灵敏度的大小, 而损耗会降低波导的相位灵敏度, 本文的结果可用于利用谐振器布局和波导参数设计耦合谐振器光波导的相位灵敏度, 对其在旋转传感方面的应用有重要意义. 关键词： 谐振器 旋转传感 光波导     

反馈式跑道型光学微环的传感灵敏度研究

提出了一种由U型反馈波导、跑道谐振腔和敏感环组成的反馈式跑道型光学微环传感器.采用耦合模理论推导了该传感器的归一化输出光强公式,数值分析了传输损耗因子、自耦合因子和敏感环尺寸对归一化输出光强的影响.分析表明:敏感环的损耗因子对归一化输出光强的调制作用明显,只要损耗因子发生微小变化,输出光强即发生较大变化;敏感环工作在弱耦合状态时传感灵敏度较高;敏感环的尺寸对传感灵敏度影响较大,适当地调整敏感环的大小可得到陡峭的输出光强谱线.对结构参数进行优化后不仅可以输出尖锐陡峭的非对称法诺谐振光强谱线,而且具有较高的法诺谐振光谱斜率,能更好地增强传感灵敏度.在信噪比为30dB的测量系统中,优化的反馈式跑道型光学微环传感器的探测极限达4.48×10-8单位折射率.     

温度测量范围加倍的单微环传感器

本文提出了一种基于U形波导耦合单微环结构的新型SOI(绝缘体上硅)温度传感器.温度变化引起感温部位有效折射率和长度变化,导致传感器的输出光谱发生漂移.根据传输矩阵法和耦合模理论,设计了新型传感器模型,并且分析了感温部位不同时系统输出光谱特性.结果表明:当U形波导耦合单微环整体结构感温时,输出光谱无伪模,消光比达到31 dB,可作为最佳感温元件.相比于传统的双直波导耦合单微环结构,当U形波导的两个耦合点间的距离为微环周长的整数倍数时,FSR(自由光谱范围)可加倍至56 nm,灵敏度提高到89.2 pm/?C,测量范围为298—720 K,实现了SOI微环谐振器的高温测量.     

串联双环光微谐振器的滤波特性

详细研究了串联双环光微谐振器的光带通滤波特性，给出了其通带带宽的公式，分析了出／入环光耦合系数和环间光耦合系数对通带特性的影响，计算并特别强调了滤波通带的结构特点，也分析了微环中存在的光损耗对串联双环光微谐振器的滤波特性的影响。     

损耗对串联双微环谐振器滤波特性的影响

对存在光损耗的串联双微环谐振器的滤波特性进行了研究.在理想耦合条件下,当环间耦合系数确定时,分析了光损耗的大小对主谐振峰的透过率、带宽、形状因子,以及伪模峰值透射率的影响,揭示了光损耗对滤波特性影响的规律.分析结果表明:主谐振峰和伪模的透射率随损耗的增大而下降,环与直波导间的耦合系数随损耗的增大而变小,而带宽和形状因子无明显变化|有损耗时环与直波导间的耦合系数不能过大也不能过小.     

垂直耦合结构纳米微环谐振器工艺失准分析

垂直耦合结构纳米微环谐振器是光子集成电路的重要组成单元.主要研究了与其实际制作相关的工艺失准问题.针对高折射率差波导材料垂直耦合结构纳米微环谐振器,先用耦合模理论解析方法研究了耦合系数与直波导和微环波导耦合层厚度d以及横向偏移量△之间的关系,为三维时域有限差分法(3D-FDTD)的精确数值计算确定了模拟范围.之后结合解...     

一种基于金刚石多层波导结构微环谐振器的仿真分析

提出了一种以金刚石新型材料为芯层的单微环谐振器模型.谐振器的纵切面采用五层脊形波导结构,中间一层设定为金刚石,上下两侧分别是SiO_2和As_2S_3,即As_2S_3-SiO_2-金刚石-SiO_2-As_2S_3.设置操作波长为1550 nm,依据耦合膜理论和微环谐振理论,利用Comsol软件仿真模拟了单直波导纵切面、直波导和环形波导耦合区的纵切面以及微环在谐振波长为1543 nm时的场强分布,及直波导和环形波导耦合区间距改变时微环的场强分布和传输特性.在此基础上,依据传输矩阵法讨论了微环的品质因数、耦合系数变化对输出光谱的影响,并对微环损耗进行了讨论.结果表明:以金刚石为芯层的微环谐振器具有良好的光学特性,本结构在谐振波长为1543 nm时谐振峰值达到了-12 dB以上,品质因数达到了1.54×10~5,在耦合系数为0.01时,自由光谱范围约为40 nm.     

马赫曾德环腔相位调制器的研究

为提高相位调制器的调制效率,结合单直波导光学环腔与带反馈的马赫曾德,提出用环形谐振腔等效为马赫曾德的上、下臂的新结构.采用耦合模理论推导了该模型的输出相位及归一化光强输出公式,数值分析了传输损耗因子、耦合角度对归一化输出光强及输出相位的影响.分析表明,输出光相位谱线随敏感环相位改变呈周期性变化,当耦合角度逐渐增大时,输出光相位谱线变尖锐,此时若要使输出相位产生π的相位差,敏感环的相位调制角度需较大.当传输因子较小时,相位谱线变化比较平缓,其最大值与最小值之间的差值不满足π的相位差.根据分析结果对结构参量进行优化,发现通过调节敏感环结构的耦合系数可以提高调制效率,仿真结果表明,当敏感环相位变化0.1π时,可以输出π的相位变化,同时归一化光强保持在0.9,满足了差分相移键控所需要的相位变化和信号幅度一致的要求,为进一步研究相位调制器提供理论依据.     

平面环形谐振腔微光学陀螺结构设计与优化

提出具有高群有效折射率的双环级联作为核心元件的谐振式平面光波导陀螺结构, 基于光学Sagnac原理得到了双微环耦合谐振式光学陀螺理论灵敏度与群有效折射率的一般表达式和双环与单环陀螺系统的灵敏度关系, 并由耦合模理论方法得到了双环系统耦合器的两个透射系数对应的群有效折射率变化情况. 在环腔半径R₁=R₂=100 μm、环腔传输损耗系数t₁=t₂=0.95的情况下, 针对环与环之间耦合器和环与波导之间耦合器透射系数对群有效折射率的不同影响, 得到了最大群有效折射率的产生条件. 采用文中参数(R=100 μm, t=0.95)计算的单环谐振式陀螺灵敏度为(10⁴-10⁵)°/h, 而双环级联谐振系统理论灵敏度能够达到10 °/h. 该研究对微环耦合谐振腔在角速度检测上的应用有重要的意义.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.     

Fiber Modal Index Measurements Based on Fiber Gratings

A novel method based on fiber gratings for measuring the effective indices of fiber modes is proposed. The effective index difference between the core mode and a cladding mode was obtained by analyzing the interference fringe of a pair of cascaded long-period fiber gratings. In order to extract the core mode index from the measured index difference, an index matching oil immersion method is proposed. By analyzing the interaction between the cladding mode and the oil applied on the cladding surface, the mode order and the effective index of the involved cladding mode might be calculated. Experimental results about the interference fringe shifts induced by the oil index and the oil-applied length are also presented.     

Optical Pulse Compression Schemes That Use Nonlinear Bragg Gratings

Nonlinear optical pulse compression of picosecond pulses typically requires long lengths of optical fiber and multiple components. Periodic structures, such as fiber Bragg gratings, are highly dispersive at wavelengths outside of the photonic bandgap. This implies that such gratings can be used as very short all-fiber compressors. In this paper a number of such compression schemes are reviewed involving uniform and nonuniform fiber Bragg gratings, relying on both soliton and nonsoliton compression principles. Experimental results supporting the corresponding underlying theory are also presented. Finally, an extension of one of the compression schemes is shown, which allows the generation of adjustable high-repetition rate soliton trains.