基于小波去噪算法的全天时大气水汽拉曼激光雷达探测与分析

提出了一种基于小波阈值去噪算法的白天太阳背景光滤波抑制方法,实现对拉曼回波信号中真实信号与噪声的分离,并有效滤除白天背景噪声。基于西安理工大学大气水汽探测拉曼激光雷达系统的全天时实测数据,详细讨论了分解层数、小波基函数、阈值函数以及阈值选取方法等因素对白天探测回波信号去噪结果的影响,对去噪前后信号进行分析并对去噪评价函数进行对比,当利用小波基sym6、分解层数为5层,并采用改进阈值函数和改进通用阈值方法的最优条件时,可实现对白天水汽拉曼散射信号和米-瑞利散射信号较好的去噪效果。讨论了小波去噪前后大气水汽混合比反演廓线和激光雷达水汽探测信噪比(SNR)的结果,分析表明利用该去噪系统得到的白天激光雷达水汽探测SNR提高约3.4倍,水汽探测距离可从1.5~2km提高到3km以上。开展全天时激光雷达连续探测实验和去噪处理,获得了24h边界层内大气水汽混合比的连续变化特性,并得到与近地面气象站数据的较一致的结果,充分验证了小波去噪算法应用于全天时大气水汽探测的可行性和有效性。     

基于高斯光束特性的Mie散射大气激光雷达回波近场信号校正研究

介绍一种基于高斯光束传输特性对Mie散射激光雷达回波信号校正的新方法.首先根据发射激光束的高斯光束特性，对大气激光雷达回波信号作高斯修正，然后在大气近似均匀假定下，对近场区经高斯修正的回波信号距离校正函数进行二次曲线拟合，实现对交叠面积影响的修正，实际计算表明，用此方法对Mie散射激光雷达回波近场信号进行处理，可获得与实际更为接近的反演结果. 关键词： 大气激光雷达 高斯光束 回波近场信号修正 大气消光系数     

成都地区中低云层的激光雷达探测

报道了应用Mie散射激光雷达探测云层的实验.利用改进的Klett反演算法对所测雷达回波信号反演获得大气消光系数分布,进一步求出云层高度、厚度及光学厚度.研究了云底高度和云层厚度在不同天气下的变化情况.获得了成都地区云层的一些重要信息,并对所得结果进行了分析讨论.     

日盲紫外域拉曼激光雷达探测大气水汽技术研究

拉曼激光雷达通过探测与水汽浓度相关的大气水汽振动拉曼散射回波信号,可实现大气水汽混合比廓线的探测。然而由于振动拉曼信号非常微弱,在白天测量时振动拉曼散射光谱会淹没在太阳背景光中,多在夜间测量。为实现大气水汽的全天时测量,设计开发一套日盲紫外波段拉曼激光雷达系统。该系统选择Nd∶YAG脉冲激光器的四倍频输出-266.0 nm日盲紫外波段作为拉曼激光雷达系统的激励波长,采用镀高增益介质膜的牛顿式望远镜作为接收器,同时利用二向色镜和超窄带干涉滤光片设计高效率的高光谱分光系统,实现了大气氧气、氮气和水汽振动拉曼散射回波信号277.5,283.6和294.6 nm的精细提取。计算仿真结果表明,臭氧吸收对日盲紫外域拉曼激光雷达探测存在一定的影响,主要是探测距离的影响;氮气通道不受白天太阳背景光噪声的影响;水汽通道存在少量太阳背景光噪声,对系统探测距离略有影响。而系统信噪比计算结果表明,设计的日盲紫外域拉曼激光雷达系统可实现白天3.5 km大气水汽的探测。实际进行水汽探测时,可利用氮气和氧气通道反演出臭氧浓度廓线,修正臭氧对发射波长、各通道拉曼散射波长的吸收,进一步提升系统的探测能力和探测精度。     

Rayleigh散射Doppler激光雷达风场反演方法改进

在Rayleigh散射Doppler激光雷达的风场反演过程中,除了温度、压强等因素之外,风速反演结果的 准确性还受到Mie散射信号的影响．当Mie散射信号较强时,尤其是遇到高层云或火山灰等情况,如果仍不考虑 气溶胶信号,由于温度不确定度和气溶胶信号的综合影响,风速反演结果将与真值偏差很大．本文提出了利用 激光雷达在垂直方向的测量信号同时反演后向散射比和大气温度的非线性迭代算法,并优化给出了最佳的 初始发射激光工作点．仿真试验结果表明:该方法可以准确有效地反演后向散射比;将该方法结合非线性迭代 风速反演方法,可以有效消除气溶胶后向散射信号的影响,进一步提高大气风速和温度的反演精度．     

基于Fizeau干涉仪的激光雷达测温方法研究

气温是描述大气状态的基本参数之一,温度的准确测量对天气预报、气候预测及其他气象参数的反演都至关重要。激光雷达作为一种遥感仪器,已经用于气象要素的探测中（风、温度、气溶胶的光学厚度等）。目前,测温激光雷达主要有拉曼激光雷达（振动和转动）、共振荧光激光雷达和Rayleigh散射激光雷达等,拉曼激光雷达需要大功率的激光器和复杂的背景滤波器;共振荧光激光雷达无法探测平流层内的温度;基于Rayleigh散射的测温激光雷达多应用于温度的相对测量,反演温度时需要建立响应函数和校准程序;基于固体腔扫描F-P干涉仪测量大气Rayleigh散射光谱来反演温度的方法,时间分辨率较低,并且该方法在测量过程中需要运动部件,所以不利于星载。在大气低层,分子的Rayleigh散射光谱会受到Brillouin散射的影响,两种散射信号叠加形成的Rayleigh-Brillouin散射光谱不再服从Gaussian分布,直接通过测量散射光谱的半高全宽来反演温度,会产生误差。基于回波能量的方法会受到气溶胶Mie散射信号的影响,所以在对流层中该方法并不适用。为了实现对流层内温度的高精度和高时间分辨率的测量,提出利用Fizeau干涉仪和PMT阵列对对流层内分子的Rayleigh-Brillouin散射光谱进行测量,并通过插值的方法来对回波信号中气溶胶Mie散射信号进行抑制,从而使Mie散射信号对温度反演的影响较小,最后将测量光谱和理论光谱进行全光谱匹配来实现温度的反演。除此之外,还对Fizeau干涉仪的自由光谱区、固体腔几何长度、腔体反射率、扫描间隔等参数进行了优化设计。为了验证本文提出方法的可行性,利用Matlab软件建立了一套仿真模型,通过模拟表明,在不考虑云、风和水汽含量的影响时,利用该方法测量对流层内的大气温度时,测量误差小于1 K。该测温方法可以对对流层内的大气温度廓线实现高精度、高时间分辨率的测量, 在测量过程中不需要使用运动部件,有较高的使用价值,并对同类高光谱激光雷达分光系统的研究具有借鉴意义, 为我国高光谱激光雷达陆基及星载应用提供了一套可行的技术方案和温度反演方法。     

南京北郊气溶胶质量浓度空间垂直分布反演

使用拉曼 米激光雷达在南京北郊进行常规性检测,通过分析激光雷达回波信号,借助气溶胶质量浓度的线性模型和指数模型进行气溶胶质量浓度空间垂直分布反演。为提高反演的精确度,对米散射信号进行近场修正,消除重叠因子的影响,拉曼散射信号进行小波分析等去噪方法处理。处理过的米散射信号用来反演0~3 km大气的气溶胶质量浓度,拉曼散射信号用来反演3 km~10 km大气的气溶胶质量浓度,然后通过2个信号拼接反演中低层气溶胶质量浓度。实验结果:2种模型反演的气溶胶质量浓度在不同时刻的相关性系数为0.991和0.973 6,具有一定的可信度。     

基于火星巡视器车载激光诱导击穿光谱仪系统设计米散射激光雷达可行性研究

火星大气气溶胶的地基探测对研究火星大气环境具有重要意义,为了能够在节约火星巡视器/着陆器体积、重量的条件下进行气溶胶探测,论证了基于巡视器车载激光诱导击穿光谱仪系统设计米散射激光雷达方案的可行性。所设计的米散射激光雷达系统使用巡视器车载激光诱导击穿光谱仪的既有硬件资源,加入分光元件和探测器模块,构成与激光诱导击穿光谱仪系统集成的米散射激光雷达,米散射激光雷达与激光诱导击穿光谱仪在火星地表分时工作,互不影响。为了论证所设计的米散射激光雷达的探测性能,对Phoenix火星探测任务中独立的米散射激光雷达得到的一组原始回波信号数据进行了处理,反演得到一组典型火星大气消光系数廓线,结合消光系数廓线与系统硬件参数计算了所设计的米散射激光雷达的回波信噪比,结果表明该系统在所用原始数据被记录的当日在火星大气边界层顶4 km高度处信噪比达到26 dB,在10 km高度附近下降到0 dB,说明基于火星巡视器车载激光诱导击穿光谱仪系统设计米散射激光雷达进行气溶胶探测具有现实可行性。对比Phoenix的独立米散射激光雷达设计方案,基于激光诱导击穿光谱仪的米散射激光雷达不但能够节省巡视器体积、重量,而且发射能量更高,回波接收方案更为简单,数据反演步骤更为简洁。     

CEEMDAN联合小波阈值算法在水下激光雷达中抑制散射杂波的应用

水下激光雷达回波信号中往往含有大量散射噪声.为了能够有效抑制散射噪声,提高水下激光雷达测距精度,提出了基于自适应完备噪声经验模态分解(CEEMDAN)与小波阈值相结合的去噪新方法.首先通过相关系数法对自适应完备噪声经验模态分解得到的本征模态函数(IMF)进行筛选;然后对筛选后的本征模态函数进行小波阈值去噪,进一步去除本征模态函数中的噪声成分;最后将去噪后的本征模态函数进行信号重构得到去噪后信号.将该方法应用到不同衰减系数水体的强度调制连续光水下测距实验,使用白色聚氯乙烯(PVC)反射板为探测目标,在3.75个衰减长度时,直接采用相关极值确定延时,测距误差达到19.2 cm;应用该方法处理后,测距误差减小到6.2 cm,有效提高测距精度.     

基于激光器输出模式的离轴激光雷达重叠因子计算及近场信号校正

基于几何分析,将离轴激光雷达在近距离范围内望远镜视场与发射激光分布的交叠区分为三种形状,并给出了计算离轴激光雷达重叠因子的解析计算公式.基于该公式和发射激光的高斯分布得到了本实验室Mie散射激光雷达重叠因子随高度的变化曲线.利用该曲线对成都地区在不同天气状况下的雷达回波信号进行了校正.在此基础上,利用Klett算法对校正后的回波信号进行了反演,得到了532 nm波长大气消光系数随高度的变化曲线.结果表明,基于文中校正方法得到的大气消光系数能反映实际的天气情况. 关键词： 离轴雷达 重叠因子 高斯模式     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.