异质结构对多通道滤波器禁带的展宽

采用光学传输矩阵法首次研究了掺有缺陷的一维三元异质结构光子晶体的传输特性。研究显示,三元异质结构光子晶体与三元周期结构光子晶体相比光子禁带显著扩大。在异质结构光子晶体中引入缺陷并调整缺陷的数目可以实现多通道滤波现象。本文主要讨论了在该结构产生一、二、三通道滤波现象。     

一维光子晶体与光学多层介质膜

本文阐述了一维光子晶体和光子禁带的概念,对比了一维光子晶体与光学多层介质膜在结构和特性方面的联系和差别,运用薄膜光学的理论和方法讨论了多层介质膜的高反射带与光子禁带和膜系结构参量的关系.     

基于异质结构的一维光子晶体红外3～5μm高反射镜设计

研究了具有异质结构且适用于3~5μm红外光区的一维光子晶体高反射镜,系统地分析了光波在一维周期性光子晶体中的反射特性,通过传输矩阵计算和仿真验证了λ/4介质膜系的反射率和最佳禁带宽度。在此基础上,选取Si和Y_2O_3两种材料,构造了24层一维光子晶体的双异质结构,仿真结果表明:在3~5μm红外波段,该结构的反射率为97.418%~99.999%。为了减少膜层数量,以金属银为衬底,设计了以Si和Y_2O_3为介质层结构的一维金属增强型光子晶体,其总层数为9层,仿真结果表明:在3~5μm红外波段,其反射率为98.943%~99.979%。     

一维光子晶体禁带特性的研究

应用传输矩阵法研究了一维光子晶体的禁带特性,数值模拟得到了一维光子晶体TE模、TM模和TE/TM模禁带结构,计算结果表明,介质层的厚度发生变化时,禁带宽度发生变化。研究结果为一维光子晶体器件的设计提供了理论依据。     

一维函数光子晶体的研究

本文提出一种新型函数光子晶体, 其折射率是空间位置函数. 由费马原理, 我们给出光在一维、 二维和三维函数光子晶体中的运动方程, 以及一维函数光子晶体的色散关系、 带隙结构和透射率, 再利用传输矩阵理论研究函数光子晶体周期数、 入射角和介质层的厚度等对透射率和禁带结构的影响, 计算发现通过选择不同的折射率空间分布函数, 可以得到比传统光子晶体更宽或更窄的禁带结构. 这样为我们设计不同带隙结构的光子晶体提供理论依据.     

基于等离子体缺陷层的一维可调谐微波光子晶体滤波特性

等离子体填充到一维介质-真空微波光子晶体的缺陷层构成一种可调谐单通道滤波器.据等离子体的强色散特性,其等效折射率与电磁波频率及等离子体频率等参数有关,因而可以通过改变等离子参数,使一维微波光子晶体缺陷层的谐振频率发生偏移,实现微波光子晶体的可调谐滤波特性.介质层和等离子体层分别采用了时域有限差分（FDTD）算法及分段线性电流密度卷积时域有限差分（PLJERC-FDTD）算法.数值模拟表明,通过改变等离子体频率可以实现滤波通道在光子禁带内较大带宽范围的移动. 关键词： 等离子体 微波光子晶体 可调谐滤波     

基于像素法用模拟退火-遗传算法搜索一维宽带隙光子晶体

将一维光子晶体用像素填充法进行二进制编码,把模拟退火、遗传算法、模拟退火-遗传混合算法与传输矩阵法结合,搜索、计算了一维光子晶体结构和能带,找到了全方位相对禁带宽度高达43.53%的四层结构和43.76%的两层结构,并给出了一维四层结构光子晶体的能带图及其4个原胞的反射率和透射率的频谱图;发现一维两层结构光子晶体的全方位禁带宽度对每层厚度的变化不敏感,但随着两种介质折射率差的增加而增大.     

光学厚度对一维三元光子晶体禁带特性的影响

运用光学传输矩阵理论,研究了一维三元光子晶体的禁带特性.数值模拟结果表明：最高折射率和最低折射率介质的光学厚度明显地影响其绝对禁带宽度,而较高折射率介质的光学厚度对其相对禁带宽度影响较大.与二元光子晶体相比,三元光子晶体的绝对带宽和相对带宽都远远大于二元光子晶体.     

硅基薄膜太阳电池一维光子晶体背反射器的模拟设计与制备

从模拟和实验两个方面研究了一种适用于硅基薄膜太阳电池的一维光子晶体新型背反射器.首先采用时域有限差分方法,模拟研究了组成一维光子晶体的两种介质的折射率比、厚度比以及周期厚度对光子禁带的影响.基于模拟结果,制备出一种由低折射率SiOx层与高折射率非晶硅a-Si层周期性交叠构成的禁带可调式一维光子晶体背反射器.通过改变a-Si层的厚度,使得禁带范围由500—750 nm波长范围红移至650—1100 nm,反射率分别达到96.4%和99%.将上述结构的一维光子晶体作为背反射器分别应用于非晶硅单结太阳电池和非晶硅/微晶硅双结叠层太阳电池,与没有背反射结构电池相比,短路电流密度分别提升了18.3%和15.2%.同时模拟研究了在不同入射角度下自然光、TE波和TM波对光子晶体反射特性的影响.研究结果表明,在太阳电池中,光线倾斜入射对一维光子晶体反射率的影响有限.     

偏振态对复周期光子晶体禁带的影响

对于一维复周期光子晶体,当制作用的波长满足一定条件时可以实现禁带的展宽,本文利用传输矩阵法数值计算了偏振态对折射率渐变的一维复周期全息光子晶体的禁带的影响。通过计算发现,制作波长不等的复周期结构光子晶体,随着再现光的照射角度增大,S偏振态下禁带出现分裂;P偏振态下禁带均可视作完整展宽,没有分裂现象。同一制作波长两次曝光制作的复周期结构,不论是P偏振还是S偏振,禁带均实现展宽而没有分裂。这一结果对实现一维全息光子晶体禁带展宽具有指导意义。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.