Copper-modified gold electrode specific for monosaccharide detection Use in amperometric determination of phenylmercury based on invertase enzyme inhibition

The electrochemical oxidation of mono- and disaccharides at various copper-modified electrodes is reported: glassy carbon modified at open circuit or by electrochemical deposition of copper, gold modified by electrochemical deposition, and at bulk copper electrodes. A comparative study of these four electrodes was made by linear sweep voltammetry and amperometry. The maximum oxidation peak separation between disaccharides and monosaccharides is about 200 mV. After optimization, amperometric determination of monosaccharides was done at +0.30 versus Ag/AgCl in 0.15 M NaOH at the copper-modified gold electrode.

Using the developed method, the enzymatic activities of invertase and β-galactosidase were determined through their reaction with sucrose and lactose, respectively. Validation was carried out by a spectrophotometric method based on 3,5-dinitrosalicylic acid, and it was shown that the proposed electrochemical method is more sensitive.

The analytical utility of the copper-modified gold electrode was tested for the determination of organic mercury. Addition of phenylmercury standards to the invertase solution caused a decrease in the enzyme activity, and allowed the determination of phenylmercury in pharmaceutical samples. The concentration has been determined in the 10–55 ng ml⁻¹ range.     

Long-lived photoinduced charge separation in carbazole–pyrene–viologen system incorporated in Langmuir–Blodgett films of substituted diazacrown ethers

Diaza-18-crown-6 ethers appending two pyrenyl (Py) or two carbazolyl (Cz) groups were synthesized. These macrocyclic compounds form 1:1 host–guest complexes with methyl viologen chloride (MV²⁺), and these complexes were assembled into monolayers by Langmuir–Blodgett technique. The generated assembly involves the general structure of donor–sensitizer–acceptor (Cz–Py–MV²⁺) in space, although any of the photo- and redox-active components are not covalently bonded. Photoirradiation of the pyrenyl group resulted in the charge-separated pair Cz√⁺–Py–MV√⁺ which survived up to hours in a well anaerobic atmosphere. An electrode was fabricated by transferring the L–B film on an ITO glass. The photoinduced voltage of this electrode was measured with a saturated calomel reference electrode in hydroquinone (H₂Q) solution to be ca. 168 mV when the light intensity was 218 mW/cm². This electrode was also used as the light electrode to construct a photogalvanic cell with a platinum electrode as the dark electrode. Irradiation of the light electrode with visible light results in anodic photocurrent, and there is no net chemical change associated with the function of the cell which converts light to electricity.     

Multiple square wave voltammetry for analytical determination of paraquat in natural water, food, and beverages using microelectrodes

This paper reports on the use of multiple square wave voltammetry (MSWV) for analytical determination of paraquat herbicide at gold microelectrode (Au-ME) in different samples of natural water, food, and beverages. In this work, the MSWV consisted in a sequence of four pairs of potential pulse in the same step and the interval potential evaluated was of the 0.0 V at −1.2 V versus Ag/AgCl 3.0 mol L⁻¹. The paraquat herbicide presented two reduction peaks, in −0.69 V and −0.99 V, with profile of the redox process totally reversible, and the use of multiple pulses allowed a detection of nanomolar levels after the optimization of experimental and voltammetric conditions. Analytical curves were constructed for pulse potential frequency of 250 s⁻¹, pulse amplitude of 50 mV, scan increment of 2 mV and pulse number of 8 pulses in a same step. The two reduction peaks showed that the peak currents were found to be directly proportional to the pesticide concentration in the range comprised between 5.0 × 10⁻⁷ mol L⁻¹ and 1.04 × 10⁻⁵ mol L⁻¹. With this, it was possible to determine detection limits (DL), which resulted in 0.044 μg L⁻¹ (0.044 ppb) and 0.146 μg L⁻¹ (0.146 ppb), respectively, for peak 1 and peak 2. DL results, obtained using MSWV, were 2–3 orders of magnitude lower (10⁻² to 10⁻³) less than those observed for traditional square wave voltammetry or published in literature, clearly pointing to the advantages arising from the possibility of using a MSWV for analytical purposes in contaminated matrices. In addition, the proposed methodology was applied in different samples of natural water, food and beverages without pre-treatment or pre-concentration step, where a recovery measurement indicated that the methodology could be employed to analyze paraquat in such matrices.     

Electrochemistry and electrocatalysis with myoglobin in biomembrane-like surfactant-polymer 2C12N+PA- composite films

Biomembrane-like polyionic complex, 2C₁₂N⁺PA⁻, was prepared by reacting sodium polyacrylate (Na⁺PA⁻) with didodecyldimethylammonium bromide (2C₁₂N⁺Br⁻). Stable thin films made from 2C₁₂N⁺PA⁻, with incorporated myoglobin (Mb), on pyrolytic graphite (PG) electrodes were then characterized by electrochemistry and other techniques. Cyclic voltammetry of Mb-2C₁₂N⁺PA⁻ films showed a pair of well-defined quasi reversible peaks for MbFe(III)/Fe(II) couple at about −0.19 V versus SCE in pH 5.5 buffers. The electron transfer rate between Mb and PG electrodes was greatly facilitated in the microenvironment of 2C₁₂N⁺PA⁻ films. Square wave voltammetry data were used to estimate the apparent heterogeneous electron transfer rate constants by nonlinear regression analysis using a model featuring dispersion of formal potentials. Positions of Soret absorption bands suggested that Mb keeps its secondary structure similar to its native state in 2C₁₂N⁺PA⁻ films at the medium pH. The results of differential scanning calorimetry and X-ray diffraction suggest that synthesized 2C₁₂N⁺PA⁻ lipid films have an ordered multibilayer structure and the incorporated Mb does not disturb this structure. Oxygen was catalytically reduced by Mb-2C₁₂N⁺PA⁻ films with a significant decrease in the electrode potential. MbFe(I), a highly reduced form of Mb, was also produced in Mb-2C₁₂N⁺PA⁻ films at about –1.09 V, and could be used to catalytically reduce organohalide pollutants such as perchloroethylene (PCE) and trichloroethylene (TCE). The catalytic reduction peak currents had linear relationships with concentrations of PCE and TCE in a range of 10–100 μM. The potential applications of the film electrode as a sensor for detecting organohalides are discussed.     

The effect of lanthanide on the degradation of RB in nanocrystalline Ln/TiO2 aqueous solution

A series of Nd³⁺, Pr³⁺, Er³⁺, and Dy³⁺ (0.25–5 at.%) homogeneously doped nanocrystalline titanium dioxides (Ln/TiO₂) were prepared by an easy sol–gel technique, and the roles of lanthanide doping on the photocatalytic activity in the degradation of rhodamine B (RB) in aqueous solution were studied. Both the concentration of the lanthanide dopant and calcination temperature showed significant effect to the photodegradation of RB. The photocatalytic activity of pure titania was drastically decreased when calcination temperature was at 700 °C, while the high photocatalytic activity was still maintained for lanthanide-doped samples. HPLC-MS method was used to study the degradation process, and it is demonstrated that the degradation of RB catalyzed by Ln/TiO₂ was principally go through with a stepwise de-ethylation photochemical process.     

A regenerable pseudo-reagentless glucose biosensor based on Nafion polymer and l,1''-dimethylferricinium mediator

Glucose oxidase was immobilized onto electrodes by co-deposition from an aqueous solution containing the diluted ion-exchange polymer Nafion. The cationic exchange property of the polymer was used to provide high local concentrations of l,1'-dimethylferricinium (DMFc⁺) mediator in the film by exchange from solution. The mediated electrodes were operated at +200 mV (vs. ), and the Nafion film was shown to reduce interfering current from ascorbate anion. Cyclic voltammetric analysis revealed a fourteen-fold increase in the effective DMFc⁺ activity at the electrode after extraction into the film. The sensitivity to glucose was 52 μA/cm²/mM in a solution containing 0.09 mM DMFc⁺, which is at least three-fold greater than reported for similar electrodes using hydrogen peroxide detection at +650 mV, with a response time of less than 1 min for a 10 μm thick membrane. Oxygen interference was significant, requiring deaeration of the solution before analysis. The electrodes exhibited no significant decrease in sensitivity for more than 50 days on storage in acetate buffer. Electrodes covered with 8000 MWCO dialysis membrane slowed the exchange of DMFc⁺ with the solution such that the Nafion film functioned as a mediator reservoir. This permitted reagentless analysis of glucose, typically capable of twenty assays when measuring concentrations between 0.1 and 1 mM. The sensitivity for glucose was 7.85 μA/cm²/mM, which is 15% of the sensitivity for the electrode without the dialysis membrane. The detection limit was 20 μM, with a linear range extending to about 3 mM, giving a dynamic range of over two orders of magnitude. Thus where some sacrifice of sensitivity and response rate may be made, the dialysis membrane cover enables multiple analyses in a reagentless biosensor scheme.     

Spectroelectrochemistry and investigation of charge transport mechanisms of iron poly(pyridyl) redox polymers

In this work, we describe the characterization of the complex [Fe(tpy-NH₂)₂](PF₆)₂ (tpy-NH₂ = bis[4′-(3-aminophenyl)-2, 2′:6′,2″-terpyridine]. The complex was oxidatively electropolymerized on glassy-carbon electrodes in CH₃CN/0.1 M tetraethylammonium perchlorate (TEAP) to generate polymer films that exhibit reversible oxidative electrochemical behavior in a wide potential range (0.0–1.6 V), as well as high conductivity and stability/durability. In situ spectrocyclic voltammetry of this modified electrode was carried out on a photodiode array spectrophotometer attached to a potentiostat, which provided UV–Vis absorption spectra of the redox species during the potential sweep. We determined charge transport parameters as a function of time and thickness of the modified electrode, and the results showed that poly-[[Fe(tpy-NH₂)₂]²⁺]_n can be made to exhibit three regimes of charge transport behavior by manipulation of the film thickness and the experimental time-scale. Morphological characterization of the film was provided by atomic force microscopy.     

阳离子交换型聚合物AQ薄膜修饰碳纤维电极及伏安行为

本文成功地制备了Eastman-AQ-55D聚合物修饰碳纤维电极,用循环伏安法探讨了一些实验参数的影响,并对Ru(NH₃)₆³⁺、甲基紫精进行了分析,结果表明,AQ-55D修饰的微电极稳定性好,修饰方法简单,灵敏度和选择性都有一定的提高,Ru(NH₃)₆³⁺、甲基紫精的峰电流与浓度在1.2×10^-6～1.2×10^-5mol/L、1.7×10^-6～1.4×10^-5mol/L范围内呈线性关系,其相关系数分别为0.999、0.998.利用此电极测定了几种离子在膜中的扩散系数.     

Metal speciation by coupled in situ graphite furnace electrodeposition and electrothermal atomic absorption spectrometry

The technique of coupled in situ electrodeposition–electrothermal atomic absorption spectrometry (ED–ETAAS) is applied to the analytes Bi, Pb, Ni and Cu. Bi, Pb, Ni and Cu are deposited quantitatively from their EDTA complexes at E_cell=1.75, 2.0, 3.0 and 2.5 V, respectively (E_cell=E_anode−E_cathode+iR). By varying the cell potential, selective reduction of free metal ions could be achieved in the presence of the EDTA complexes. For Bi³⁺ and Pb²⁺ this utilised the voltage windows E_cell=0.6–1.0 and 1.8–2.0 V, respectively. For Ni, deposition at E_cell=1.7–2.0 V achieved substantial, but not complete, differentiation between Ni²⁺ (ca. 90–100% deposition) and Ni(EDTA)²⁻ (ca. 12–20% deposition). An adequate voltage window was not obtained for Cu. The ability of ED–ETAAS to differentiate between electrochemically labile and inert species was demonstrated by application of both ED–ETAAS and anodic stripping voltammetry to the time-dependent speciation of Pb in freshly mixed Pb²⁺–NaCl media. Application to natural water samples is complicated by adsorption of natural organic matter to the graphite cathode.     

Vibrational spectra and microstructure of poly(ε-caprolactone)/siloxane biohybrids doped with lithium triflate

Fourier Transform infrared (FT-IR) and Raman (FT-Raman) spectroscopies and Scanning Electron Microscopy (SEM) were used to investigate ionic association, hydrogen bonding and morphology in a family of sol–gel derived lithium triflate (LiCF₃SO₃)-doped di-urethane cross-linked poly(ε-caprolactone) (PCL(530))/siloxane hybrid electrolytes. The materials studied, with compositions ∞ > n  0.5 (where n – composition – expresses the molar ratio of PCL(530) ester repeat units per Li⁺ ion), are non-porous and homogeneous. The Li⁺ ions interact with the urethane and ester carbonyl oxygen atoms within the whole range of salt concentration analyzed, promoting the formation of hydrogen-bonded aggregates. The composition dependence of the relative concentration of “free” anions and coordinated anions (weakly coordinated anions, ion pairs or [Li(CF₃SO₃)₂]⁻ triplets, aggregates I ([Li₂(CF₃SO₃)]⁺) and aggregates II ([Li₃(CF₃SO₃)]²⁺) in all the samples is in perfect agreement with the values of the room temperature ionic conductivity reported previously.     

Biosensor for phenol based on the direct electron transfer blocking of peroxidase immobilising on silica–titanium

Horseradish peroxidase (HRP) was immobilised on silica gel modified with titanium oxide. This material was employed to prepare modified carbon paste electrode. The direct electron transfer of the hydrogen peroxide reduction by HRP was blocked when immobilised on silica–titanium. This biosensor presented a very sensitive response for phenol (1 μmol l⁻¹) at an applied potential of 0 mV vs SCE. The best condition was achieved in phosphate buffer pH 6.8, ratio of hydrogen peroxide/phenol higher than 0.35. The biosensor showed a linear response range between 10 and 50 μmol l⁻¹ of phenol, adjusted by the equation j=−32.8+16.3 [phenol], for n=5 with a correlation coefficient of 0.9995. The response time of the biosensor was about 3 s.     

Dual-analyte spectroscopic sensing in sol-gel derived polyelectrolyte-silica composite thin films

Ferrozine (3-(2-pyridyl)-5,6-diphenyl-1,2,4-triazine-p,p′-disulfonic acid, monosodium salt hydrate), an iron indicator, and HTPS (8-hydroxyl-1,3,6-pyrenetrisulfonic acid, trisodium salt), a pH indicator, were immobilized in sol–gel derived PDMDAAC-SiO₂ (where PDMDAAC stands for poly(dimethyldiallylammonium chloride), composite thin films via ion-exchange. The two indicators were immobilized in two adjacent sections of the same PDMDAAC-SiO₂ film which was supported on a glass optical substrate. The spectroscopic response of the film to both Fe²⁺ and H⁺ in solutions was investigated by attenuated total reflection (ATR) spectrometry at two well-separated wavelengths, 562 nm for Fe²⁺ and 460 nm for H⁺. The Ferrozine/HPTS immobilized PDMDAAC-SiO₂ films had the following characteristics: linear range, 2.5×10⁻⁶–5.0×10⁻⁵ M for Fe²⁺, pH 4.1–6.8 for H⁺; sensitivity, 2.2×10⁴ ΔA/M for Fe²⁺, 0.583 ΔA/pH for H⁺.     

Determination of potassium ions in biodiesel using a nickel(II) hexacyanoferrate-modified electrode

In this work, nickel hexacyanoferrate-modified electrode was developed to determine potassium ions in biodiesel by potentiometry. The modified electrodes exhibit a linear response to potassium ions in the concentration range of 4.0 × 10⁻⁵ to 1.0 × 10⁻² mol L⁻¹, with a detection limit of 1.9 × 10⁻⁵ mol L⁻¹, and a near-Nernstian slope (53–55 mV per decade) at 25 °C. The method developed in this work was compared with flame photometry and the potassium concentration found in biodiesel showed that the modified electrode method gives results similar to those obtained by flame photometry.     

Donnan dialysis preconcentration coupled with ion chromatography and electrocatalytic oxidation for the determination of cyanide

An electrocatalytic amperometric detector for the ion chromatographic determination of CN⁻ is described. A conducting composite that is based on a graphite-loaded sol–gel material comprises the working electrode. The composite is doped with a Ru^II metallodendrimer which is demonstrated to promote the electrochemical oxidation of CN⁻ at potentials positive of 0.5 V vs. Ag/AgCl. In 6 mM NaOH, 0.05 M NaCl flowed at 1.0 ml min⁻¹, a 5-point calibration curve with the following linear least squares parameters is obtained over the range, 1.0–30 M CN⁻: slope, 24.2±0.1 nA M⁻¹; intercept, −6±2 nA; and r, 0.9997. The detection limit, 0.7 μM CN⁻, compares favorably to that obtained by amperometry at a silver electrode, 0.5 μM CN⁻, under comparable experimental conditions. A 60-min preconcentration by Donnan dialysis increases the sensitivity by a factor of 23.6.     

Electron transfer of quinone self-assembled monolayers on a gold electrode

Dialkyl disulfide-linked naphthoquinone, (NQ-C_n-S)₂, and anthraquinone, (AQ-C_n-S)₂, derivatives with different spacer alkyl chains (C_n: n = 2, 6, 12) were synthesized and these quinone derivatives were self-assembled on a gold electrode. The formation of self-assembled monolayers (SAMs) of these derivatives on a gold electrode was confirmed by infrared reflection-absorption spectroscopy (IR-RAS). Electron transfer between the derivatives and the gold electrode was studied by cyclic voltammetry. On the cyclic voltammogram a reversible redox reaction between quinone (Q) and hydroquinone (QH₂) was clearly observed under an aqueous condition. The formal potentials for NQ and AQ derivatives were −0.48 and −0.58 V, respectively, that did not depend on the spacer length. The oxidation and reduction peak currents were strongly dependent on the spacer alkyl chain length. The redox behavior of quinone derivatives depended on the pH condition of the buffer solution. The pH dependence was in agreement with a theoretical value of E_1/2 (mV) = E′ − 59pH for 2H⁺/2e⁻ process in the pH range 3–11. In the range higher than pH 11, the value was estimated with E_1/2 (mV) = E′ − 30pH , which may correspond to H⁺/2e⁻ process. The tunneling barrier coefficients (β) for NQ and AQ SAMs were determined to be 0.12 and 0.73 per methylene group (CH₂), respectively. Comparison of the structures and the alkyl chain length of quinones derivatives on these electron transfers on the electrode is made.     

Extraction of Pb(II), Cd(II), and Hg(II) from aqueous solution by nitrogen and thiol functionality grafted to silica gel measured by calorimetry

The reaction of ethylene sulfide with 3-aminopropyltrimethoxysilane gave a new silylating agent, which was anchored onto a silica surface via the sol–gel procedure. This surface displayed a chelating moiety containing nitrogen and two sulfur basic centers potentially capable of extracting cations from aqueous solutions. The process of metal extraction was followed by a batch method, and fitted to a modified Langmuir equation. The maximum adsorption capacities found were: 2.06 ± 0.01, 3.72 ± 0.02, and 5.14 ± 0.02 mmol g⁻¹ for Pb(II), Cd(II), and Hg(II), respectively. The enthalpies of bending are: −1.16 ± 0.04, −3.60 ± 0.10, and −8.94 ± 0.03 kJ mol⁻¹ for Cd(II), Pb(II), and Hg(II), respectively. The Gibbs free energies of binding agree with the spontaneity of the proposed reactions between cations and basic centers.     

Simultaneous determination of trace uranium(VI) and zinc(II) by adsorptive cathodic stripping voltammetry with aluminon ligand

Uranium(VI) complexed with aluminon (3-[bis(3-carboxy-4-hydroxy-phenyl)methylene]-6-oxo-1,4-cyclohexadiene-1-carboxylic acid triammonium salt) was determined by adsorptive cathodic stripping voltammetry (ACSV) using a hanging mercury drop electrode. Trace uranium(VI) and zinc(II) can be simultaneously determined in a single scan in the presence of aluminon and urea. Optimal conditions were found to be: accumulation time; 180–200 s, accumulation potential; 50 mV versus Ag/AgCl, scan rate; 40 mV s⁻¹, supporting electrolyte; 0.1 M sodium acetate buffer at pH 6.5–7.0, and concentration of aluminon; 1×10⁻⁶ M. The linear range of uranium(VI) and zinc(II) were observed over the concentration range 2–33 and 30–120 ng ml⁻¹, respectively. The detection limit (S/N=3) are 0.2 ng ml⁻¹ (uranium) and 30 ng ml⁻¹ (zinc). A good reproducibility shows RSDs of 2.5–4.0% (n=10). The procedure offers high selectivity, with the presence of urea masking some metal ions.     

An NMR study of methanol diffusion in polymer electrolyte fuel cell membranes

Methanol diffusion in two polymer electrolyte membranes, Nafion 117 and BPSH 40 (a 40% disulfonated wholly aromatic polyarylene ether sulfone), was measured using a modified pulsed field gradient NMR method. This method allowed for the diffusion coefficient of methanol within the membrane to be determined while immersed in a methanol solution of known concentration. A second set of gradient pulses suppressed the signal from the solvent in solution, thus allowing the methanol within the membrane to be monitored unambiguously. Over a methanol concentration range of 0.5–8 M, methanol diffusion coefficients in Nafion 117 were found to increase from 2.9 × 10⁻⁶ to 4.0 × 10⁻⁶ cm² s⁻¹. For BPSH 40, the diffusion coefficient dropped significantly over the same concentration range, from 7.7 × 10⁻⁶ to 2.5 × 10⁻⁶cm² s⁻¹. The difference in diffusion behavior is largely related to the amount of solvent sorbed by the membranes. Increasing the methanol concentration results in an increase in solvent uptake for Nafion 117, while BPSH 40 actually excludes the solvent at higher concentrations. In contrast, diffusion of methanol measured via permeability measurements (assuming a partition coefficient of 1) was lower (1.3 × 10⁻⁶ and 6.4 × 10⁻⁷ cm² s⁻¹ for Nafion 117 and BPSH 40 respectively) and showed no concentration dependence. The differences observed between the two techniques are related to the length scale over which diffusion is monitored and the partition coefficient, or solubility, of methanol in the membranes as a function of concentration. For the permeability measurements, this length is equal to the thickness of the membrane (178 and 132 μm for Nafion 117 and BPSH 40 respectively) whereas the NMR method observes diffusion over a length of approximately 4–8 μm. Regardless of the measurement technique, BPSH 40 is a greater barrier to methanol permeability at high methanol concentrations.     

芘四硫酸四钠盐/甲基紫精复合物光物理性质的研究

本文通过吸收光谱滴定和时间分辨瞬态吸收光谱对芘四硫酸四钠盐(pyrenetetrasulfonic acid tetrasodium salt,PyTS)/甲基紫精(methylviologen,MV²⁺)复合物在水溶液中的光物理性质进行研究。用甲基紫精滴定芘四硫酸四钠盐时,得到该复合物的组成成份是1:1,反之,用芘四硫酸四钠盐滴定甲基紫精时,同样得到1:1组成成份的复合物。该复合物的形成常数是2.4×10⁶mol^-1·L,当用光激发该复合物时,发现其中存在芘四硫酸四钠盐到甲基紫精的电子转移过程,并得到该过程的动力学模型。     

Probing chiral amino acids at sub-picomolar level based on bovine serum albumin enantioselective films coupled with silver-enhanced gold nanoparticles

A novel electrochemical sensor with capability of probing chiral amino acids with gold nanoparticle (n-Au) labels using bovine serum albumin (BSA) as a chiral selector and subsequent signal amplification step by silver enhancement is introduced. The assay relies on the stereoselectivity of BSA embedded in ultrathin γ-alumina sol–gel film coated on the surface of the glassy carbon electrode (GCE). The recognition to the n-Au-labeled l- or d-amino acids for BSA-GCE could be monitored by the differential pulse voltammetry (DPV), while the DPV signal was greatly amplified by the anchored silver atoms on the n-Au, leading to a new way of quantitatively analysis of chiral amino acids electrochemically at sub-picomolar level. With l-tryptophan as the probe solute, the linear concentration range was from 1.33 × 10⁻¹² to 1 × 10⁻⁹ mol L⁻¹ and detection limit was 5 × 10⁻¹³ mol L⁻¹. For tryptophan enantiomers, the enantioselectivity coefficient 2.3 was obtained.