低雷诺数俯仰振荡翼型等离子体流动控制

针对低雷诺数翼型气动性能差的特点, 通过介质阻挡放电(dielectric barrier discharge, DBD)等离子体激励控制的方法, 提高翼型低雷诺数下的气动特性,改善其流场结构. 采用二维准直接数值模拟方法求解非定常不可压Navier-Stokes方程,对具有俯仰运动的NACA0012翼型的低雷诺数流动展开数值模拟.同时将介质阻挡放电激励对流动的作用以彻体力源项的形式加入Navier-Stokes方程,通过数值模拟探究稳态DBD等离子体激励对俯仰振荡NACA0012翼型气动特性和流场特性的影响.为了进行流动控制, 分别在上下表面的前缘和后缘处安装DBD等离子体激励器,并提出四种激励器的开环控制策略,通过对比研究了这些控制策略在不同雷诺数、不同减缩频率以及激励位置下的控制效果.通过流场结构和动态压强分析了等离子体进行流场控制的机理. 结果表明,前缘DBD控制中控制策略B(负攻角时开启上表面激励器,正攻角时开启下表面激励器)效果最好,后缘DBD控制中控制策略C(逆时针旋转时开启上表面激励器,顺时针旋转时开启下表面激励器)效果最好,前缘DBD控制效果会随着减缩频率的增大而下降, 同时会导致阻力增大.而后缘DBD控制可以减小压差阻力, 优于前缘DBD控制,对于计算的所有减缩频率(5.01~11.82)都有较好的增升减阻效果.在不同雷诺数下, DBD控制的增升效果较为稳定, 而减阻效果随着雷诺数的降低而变差,这是由流体黏性效应增强导致的.      

Flow control over a NACA 0012 airfoil using dielectric-barrier-discharge plasma actuator with a Gurney flap

Flow control study of a NACA 0012 airfoil with a Gurney flap was carried out in a wind tunnel, where it was demonstrated that a dielectric-barrier-discharge (DBD) plasma actuator attached to the flap could increase the lift further, but with a small drag penalty. Time-resolved PIV measurements of the near-wake region indicated that the plasma forcing shifted the wake downwards, reducing its recirculation length. Analysis of wake vortex dynamics suggested that the plasma actuator initially amplified the lower wake shear layer by adding momentum along the downstream surface of the Gurney flap. This enhanced mutual entrainment between the upper and lower wake vortices, leading to an increase in lift on the airfoil.     

High-lift airfoil trailing edge separation control using a single dielectric barrier discharge plasma actuator

Control of flow separation from the deflected flap of a high-lift airfoil up to Reynolds numbers of 240,000 (15 m/s) is explored using a single dielectric barrier discharge (DBD) plasma actuator near the flap shoulder. Results show that the plasma discharge can increase or reduce the size of the time-averaged separated region over the flap depending on the frequency of actuation. High-frequency actuation, referred to here as quasi-steady forcing, slightly delays separation while lengthening and flattening the separated region without drastically increasing the measured lift. The actuator is found to be most effective for increasing lift when operated in an unsteady fashion at the natural oscillation frequency of the trailing edge flow field. Results indicate that the primary control mechanism in this configuration is an enhancement of the natural vortex shedding that promotes further momentum transfer between the freestream and separated region. Based on these results, different modulation waveforms for creating unsteady DBD plasma-induced flows are investigated in an effort to improve control authority. Subsequent measurements show that modulation using duty cycles of 50–70% generates stronger velocity perturbations than sinusoidal modulation in quiescent conditions at the expense of an increased power requirement. Investigation of these modulation waveforms for trailing edge separation control similarly shows that additional increases in lift can be obtained. The dependence of these results on the actuator carrier and modulation frequencies is discussed in detail.     

Rolling/sliding of a particle on a flat wall in a linear shear flow at finite Re

Recently Lee and Balachandar proposed analytically-based expressions for drag and lift coefficients for a spherical particle moving on a flat wall in a linear shear flow at finite Reynolds number. In order to evaluate the accuracy of these expressions, we have conducted direct numerical simulations of a rolling particle for shear Reynolds number up to 100. We assume that the particle rolls on a horizontal flat wall with a small gap separating the particle from the wall (L = 0.505) and thus avoiding the logarithmic singularity. The influence of the shear Reynolds number and the translational velocity of the particle on the hydrodynamic forces of the particle was investigated under both transient and the final drag-free and torque-free steady state. It is observed that the quasi-steady drag and lift expressions of Lee and Balachandar provide good approximation for the terminal state of the particle motion ranging from perfect sliding to perfect rolling. With regards to transient particle motion in a wall-bounded shear flow it is observed that the above validated quasi-steady drag and lift forces must be supplemented with appropriate wall-corrected added-mass and history forces in order to accurately predict the time-dependent approach to the terminal steady state. Quantitative comparison with the actual particle motion computed in the numerical simulations shows that the theoretical models quite effective in predicting rolling/sliding motion of a particle in a wall-bounded shear flow at moderate Re.     

等离子体激励器诱导射流的湍流特性研究

为了进一步掌握等离子体流动控制机理, 完善等离子体激励器数学模型, 提升等离子体激励器扰动能力, 采用粒子图像测速技术, 在静止空气下开展了介质阻挡放电等离子体激励器诱导射流特性研究. 实验时, 将非对称布局激励器布置在平板模型上, 随后将带有激励器的模型放置在有机玻璃箱内, 从而避免环境气流对测试结果的影响. 基于激励器诱导流场, 分析了激励电压对诱导射流特性的影响, 揭示了较高电压下诱导射流近壁区的拟序结构, 获得了卷起涡、二次涡等拟序结构的演化发展过程, 计算了卷起涡脱落频率, 阐述了卷起涡与启动涡的区别, 初步探索了卷起涡的耗散机制. 结果表明: (1)层流射流不能完全概括等离子体诱导射流特性, 激励电压是影响射流特性的重要参数. 当电压较低时, 诱导射流为层流射流; 当电压较高时, 诱导射流的雷诺数提高, 射流剪切层不稳定, 层流射流逐渐发展为湍流射流. (2)等离子体诱导湍流射流包含着卷起涡、二次涡等拟序结构; 在固定电压下, 这些涡结构存在恒定的卷起频率. (3)当激励电压较高时, 流动不稳定使得卷起涡发生了拉伸、变形, 引起了流场湍动能增大, 从而加速了卷起涡的耗散. 研究结果为全面认识激励器射流特性, 进一步挖掘激励器卷吸掺混能力, 提升激励器控制能力积累基础.      

Numerical study on the suppression of the vortex-induced vibration of an elastically mounted cylinder by a traveling wave wall

In the present paper, the commercial CFD code “Fluent” was employed to perform 2-D simulations of an entire process that included the flow around a fixed circular cylinder, the oscillating cylinder (vortex-induced vibration, VIV) and the oscillating cylinder subjected to shape control by a traveling wave wall (TWW) method. The study mainly focused on using the TWW control method to suppress the VIV of an elastically supported circular cylinder with two degrees of freedom at a low Reynolds number of 200. The cross flow (CF) and the inline flow (IL) displacements, the centroid motion trajectories and the lift and drag forces of the cylinder that changed with the frequency ratios were analyzed in detail. The results indicate that a series of small-scale vortices will be formed in the troughs of the traveling wave located on the rear part of the circular cylinder; these vortices can effectively control the flow separation from the cylinder surface, eliminate the oscillating wake and suppress the VIV of the cylinder. A TWW starting at the initial time or at some time halfway through the time interval can significantly suppress the CF and IL vibrations of the cylinder and can remarkably decrease the fluctuations of the lift coefficients and the average values of the drag coefficients; however, it will simultaneously dramatically increase the fluctuations of the drag coefficients.     

机翼尺度效应对等离子体分离流动控制特性的影响

等离子体流动控制技术是一种以等离子体气动激励为控制手段的主动流动控制技术. 为了进一步提高等离子体激励器可控机翼尺度, 以超临界机翼SC(2)-0714大迎角分离流为研究对象, 以对称布局介质阻挡放电等离子体为控制方式, 以测力、粒子图像测速仪为研究手段, 从等离子体激励器特性研究出发, 深入开展了机翼尺度效应对等离子体控制的影响研究, 提出了适用于分离流控制的能效比系数, 探索了分离流等离子体控制机理, 掌握了机翼尺度对分离流控制的影响规律. 结果表明: (1)随着机翼尺度的增大, 布置到机翼上的激励器电极长度会相应增加; 在本文的参数研究范围内, 激励器的平均消耗功率不会随电极长度的增加而线性增大; 当电极长度达到一定阈值时, 激励器的平均消耗功率趋于定值; (2)在固定雷诺数的情况下, 随着机翼尺度的增大, 等离子体的控制效果并未降低, 激励器能效比系数提高; (3)等离子体在主流区诱导的大尺度展向涡与在壁面附近产生的一系列拟序结构成为分离流控制的关键. 研究结果为实现真实飞机的等离子体分离流控制, 推动等离子体流动控制技术工程化应用提供了技术支撑.      

NUMERICAL STUDY ON DYNAMIC STALL FLOW CONTROL FOR WIND TURBINE AIRFOIL USING PLASMA ACTUATOR 1)

针对动态失速引起的风力机翼型气动性能恶化的问题,本文基于动网格和滑移网格技术, 开展了大涡模拟数值计算研究,探索了非定常脉冲等离子体的动态流动控制机理. 结果表明,等离子体气动激励能够有效控制翼型动态失速, 改善平均和瞬态气动力,减小力矩负峰值和迟滞环面积. 压力分布在等离子体施加范围内出现了负压"凸起",上翼面吸力峰值明显增大.脉冲频率和占空比这两个非定常控制参数对流动控制影响显著,无因次脉冲频率为1.5时等离子体控制效果较好,占空比为0.8时即可接近连续工作模式下的气动收益. 翼型深失速状态,等离子体促使流动分离位置明显向后缘移动, 抵抗了大尺度动态失速涡的发生,分离涡结构破碎耗散、重新附着, 涡流影响范围减小; 浅失速状态,等离子体激励具有较强的剪切层操纵能力, 诱导了翼型边界层提前转捩,促进了与主流的动量掺混. 等离子体气动激励诱导出前缘附近贴体翼面"涡簇",起到了虚拟气动外形的作用.不同尺度、频域的动态涡结构与等离子体气动激励的非线性、强耦合作用导致了气动力/力矩的谐波振荡.     

风力机翼型动态失速等离子体流动控制数值研究

针对动态失速引起的风力机翼型气动性能恶化的问题,本文基于动网格和滑移网格技术, 开展了大涡模拟数值计算研究,探索了非定常脉冲等离子体的动态流动控制机理. 结果表明,等离子体气动激励能够有效控制翼型动态失速, 改善平均和瞬态气动力,减小力矩负峰值和迟滞环面积. 压力分布在等离子体施加范围内出现了负压"凸起",上翼面吸力峰值明显增大.脉冲频率和占空比这两个非定常控制参数对流动控制影响显著,无因次脉冲频率为1.5时等离子体控制效果较好,占空比为0.8时即可接近连续工作模式下的气动收益. 翼型深失速状态,等离子体促使流动分离位置明显向后缘移动, 抵抗了大尺度动态失速涡的发生,分离涡结构破碎耗散、重新附着, 涡流影响范围减小; 浅失速状态,等离子体激励具有较强的剪切层操纵能力, 诱导了翼型边界层提前转捩,促进了与主流的动量掺混. 等离子体气动激励诱导出前缘附近贴体翼面"涡簇",起到了虚拟气动外形的作用.不同尺度、频域的动态涡结构与等离子体气动激励的非线性、强耦合作用导致了气动力/力矩的谐波振荡.      

电磁极宽度对圆柱绕流场影响的数值分析

在雷诺数Re=200的情况,利用Maxwell方程直接数值计算表面包覆电极与磁极圆柱体产生的电磁力分布,将其加入到动量方程中,在各种电磁力作用参数和电磁极宽度的组合下,对表面覆盖电磁极圆柱体在弱电解质中的绕流场结构及其升阻力特性进行了数值模拟与分析.结果表明,当电磁极宽度较小时,圆柱体绕流场的分离点越容易接近后驻点,而电磁力对总阻力的影响并不明显,但对压差和摩擦阻力均有明显影响.当电磁极宽度较大时,圆柱体尾部区域越容易产生射流现象,而且总阻力随电磁力作用参数和电磁极宽度增大而减小.在电磁力尚不足以完全抑制周期性涡脱落的情况下,升力幅值随电磁力作用参数增大而减小,但随电磁极宽度则先减小后略有增加,升力脉动频率则均随电磁力作用参数和电磁极宽度增大而增加.研究表明,电磁力可以有效地改善圆柱体绕流场结构,达到减小圆柱体阻力并抑制其脉动升力之目的,因此是圆柱型结构的一种有效流动控制手段.     

正弦交流介质阻挡放电等离子体激励器诱导流场研究的进展与展望

正弦交流介质阻挡放电等离子体流动控制技术是基于等离子体激励的主动流动控制技术,具有响应时间短、结构简单、能耗低、不需要额外气源装置等优点,在飞行器增升减阻、抑振降噪、助燃防冰等方面具有广阔的应用前景.针对“激励器消耗的大部分能量尚未被挖掘利用、诱导流场的完整演化过程尚未完全掌握、诱导流场的演化机制尚不明确”这三方面问题,本文首先从激励器诱导流场的空间结构、时空演化过程、演化机制三个方面回顾总结了激励器诱导流场的研究进展.在诱导流场空间结构方面,发现了高电压激励下诱导射流的湍流特性,辨析了壁面拟序结构与无量纲激励参数之间的关联机制;从激励器诱导声能方面挖掘出了激励器潜在的能量,发现了“等离子体诱导超声波与诱导声流”的新现象,提出了声激励机制;在时空演化过程方面,阐明了激励器诱导流场从薄型壁射流发展为“拱形”射流、再演变为启动涡,最终形成准定常射流的完整演化过程;在演化机制方面,结合声学特性提出了以“升推”为主的诱导流场演化机制.其次,围绕激励器诱导流场,进一步凝练出下一步研究重点,为突破等离子体流动控制技术瓶颈,打通“概念创新—技术突破—演示验证”的创新链路,实现工程应用提供支撑.     

Frequency effects on lift and drag for flow past an oscillating cylinder

A transversely oscillating cylinder in a uniform flow is modeled to investigate frequency effects of flow-induced wake on lift and drag of the cylinder. Specifically, verified unsteady fluid dynamic simulations using an immersed-boundary method in a fixed Cartesian grid predict the flow structure around the cylinder and reveal how the integration of surface pressure and shear distributions provides lift and drag on the oscillating cylinder. In this study, frequency ranges to be considered are both near and away from the natural frequency of wake vortex shedding. Subsequently, the effects of frequency lock-in, superposition and demultiplication on lift and drag are discussed based on the spectral analysis of time histories of lift and drag.     

On the development of lift and drag in a rotating and translating cylinder

The two-dimensional flow around a rotating cylinder is investigated numerically using a vorticity forces formulation with the aim of analyzing quantitatively the flow structures, and their evolutions, that contribute to the lift and drag forces on the cylinder. The Reynolds number considered, based on the cylinder diameter and steady free stream speed, is Re=200, while the non-dimensional rotation rate (ratio of the surface speed and free stream speed) selected was α=1 and 3. For α=1 the wake behind the cylinder for the fully developed flow is oscillatory due to vortex shedding, and so are the lift and drag forces. For α=3 the fully developed flow is steady with constant (high) lift and (low) drag. Each of these cases is considered in two different transient problems, one with angular acceleration of the cylinder and constant speed, and the other one with translating acceleration of the cylinder and constant rotation. We characterize quantitatively the contributions of individual fluid elements (vortices) to aerodynamic forces, explaining and quantifying the mechanisms by which the lift is generated in each case. In particular, for high rotation (when α=3), we explain the relation between the mechanisms of vortex shedding suppression and those by which the lift is enhanced and the drag is almost suppressed when the fully developed flow is reached.     

等离子体激励器控制圆柱绕流的实验研究

为了发展新型移动附面层控制技术,提升流动控制效率,采用粒子图像测速技术,开展了基于对称布局等离子体气动激励的圆柱绕流控制研究,获得了静止空气下,对称布局激励器诱导流场的演化过程,评估了来流条件下等离子体控制效果,通过等离子体诱导涡实现了虚拟移动附面层控制,分析了诱导涡随时间演化的过程,揭示了圆柱绕流等离子体控制机理.结果表明:(1)在静止空气下,对称布局激励器在刚启动瞬间,会在暴露电极两侧诱导产生一对旋转方向相反的启动涡;随着时间的推移,启动涡逐渐向远离壁面的方向运动;随后,激励器在暴露电极两侧产生了两股速度近似相等,方向相反的诱导射流,诱导射流在柯恩达效应的影响下,朝壁面方向发展.(2)当激励电压峰峰值为19.6 kV,激励频率3kHz时,施加等离子体气动激励后,圆柱脱落涡得到了较好抑制,圆柱阻力系数减小了21.8％;(3)在来流作用下,对称布局激励器在靠近来流一侧,诱导产生了较为稳定的涡结构.诱导涡通过旋转、运动,促进了壁面附近低能气流与主流之间的掺混,抑制了圆柱绕流流场分离,实现了"虚拟移动附面层控制"效果.与传统移动附面层控制技术相比,基于等离子体气动激励的新型移动附面层控制技术不需要复杂、笨重的机构,不会带来额外的阻力,具有潜在的应用前景.      

EXPERIMENTAL INVESTIGATION ON LIFT INCREMENT OF A PLASMA CIRCULATION CONTROL AIRFOIL

利用等离子体激励器发展了新型的环量增升技术,并对二维NACA0012翼型绕流实施控制。由于NACA0012翼型为尖后缘构型,环量增升装置由2个非对称型介质阻挡放电等离子体激励器构成。一个等离子体激励器贴附于翼型吸力面靠近后缘处,其诱导的壁面射流沿来流方向指向下游;另一个等离子体激励器贴附于翼型压力面靠近后缘处,其诱导的壁面射流与来流方向相反指向上游。在风洞中通过时间解析二维PIV系统对翼型绕流流场进行了测量,基于翼型弦长的雷诺数Re=20 000。结果表明在等离子体激励器的控制下,翼型压力面靠近后缘处可以形成一个定常回流区,从而起到虚拟气动外形的作用,因此翼型吸力面的流场得到加速,压力面的流场得到减速,使得翼型压力面的吸力以及压力面的压力都得到增加,进而增加了翼型的环量。风洞天平测力实验进一步验证了该环量增升技术的有效性。在整个攻角范围内,施加控制的翼型的升力系数相比没有控制的工况有明显的提高。     

Drag and lift reduction of a 3D bluff-body using active vortex generators

In this study, a passive flow control experiment on a 3D bluff-body using vortex generators (VGs) is presented. The bluff-body is a modified Ahmed body (Ahmed in J Fluids Eng 105:429–434 1983) with a curved rear part, instead of a slanted one, so that the location of the flow separation is no longer forced by the geometry. The influence of a line of non-conventional trapezoïdal VGs on the aerodynamic forces (drag and lift) induced on the bluff-body is investigated. The high sensitivity to many geometric (angle between the trapezoïdal element and the wall, spanwise spacing between the VGs, longitudinal location on the curved surface) and physical (freestream velocity) parameters is clearly demonstrated. The maximum drag reduction is ?12%, while the maximum global lift reduction can reach more than ?60%, with a strong dependency on the freestream velocity. For some configurations, the lift on the rear axle of the model can be inverted (?104%). It is also shown that the VGs are still efficient even downstream of the natural separation line. Finally, a dynamic parameter is chosen and a new set-up with motorized vortex generators is proposed. Thanks to this active device. The optimal configurations depending on two parameters are found more easily, and a significant drag and lift reduction (up to ?14% drag reduction) can be reached for different freestream velocities. These results are then analyzed through wall pressure and velocity measurements in the near-wake of the bluff-body with and without control. It appears that the largest drag and lift reduction is clearly associated to a strong increase of the size of the recirculation bubble over the rear slant. Investigation of the velocity field in a cross-section downstream the model reveals that, in the same time, the intensity of the longitudinal trailing vortices is strongly reduced, suggesting that the drag reduction is due to the breakdown of the balance between the separation bubble and the longitudinal vortices. It demonstrates that for low aspect ratio 3D bluff-bodies, like road vehicles, the flow control strategy is much different from the one used on airfoils: an early separation of the boundary layer can lead to a significant drag reduction if the circulation of the trailing vortices is reduced.     

Numerical simulation of flow around a square cylinder in uniform-shear flow

This paper presents results obtained from a numerical simulation of a two-dimensional (2-D) incompressible linear shear flow over a square cylinder. Numerical simulations are performed, using the lattice Boltzmann method, in the ranges of 50⩽Re⩽200 and 0⩽K⩽0.5, where Re and K are the Reynolds number and the shear rate, respectively. The effect of the shear rate on the frequency of vortex shedding from the cylinder, and the lift and drag forces exerted on the cylinder are quantified together with the flow patterns around the cylinder. The present results show that vortex structure behind the cylinder is strongly dependant on both the shear rate and Reynolds number. When Re=50, a small K can disturb the steady state and cause an alternative vortex shedding with uneven intensity. In contrast, a large value of K will suppress the vortex shedding from the cylinder. When Re>50, the differences in the strength and size of vortices shed from the upper and lower sides of the cylinder become more pronounced as K increases. Vortex shedding disappears when K is larger than a critical value, which depends on Re. The flow patterns around the cylinder for different Re tend towards self-similarity with increasing K. The lift and drag forces exerted on the cylinder, in general, decrease with increasing K. Unlike a shear flow past a circular cylinder, the vortex shedding frequency past a square cylinder decreases with increasing the shear rate. A significant reduction of the drag force occurs in the range 0.15<K<0.3.     

Modelling the Plasma-actuator-related Turbulence Production in RANS Closures by Reference to Complementary Experimental Investigations

Complementary experimental and computational study on flow separation delay at a NACA 0015 airfoil affected by a DBD (Dielectric-Barrier-Discharge) plasma actuator is presented. The effect of the DBD plasma-actuator on the flow development towards its appropriate control is accounted through a relevant body force representing a source term in the equation of motion. The spatial distribution of the force is calculated from the time-averaged properties of the experimentally obtained (by particle image velocimetry - PIV) velocity field by applying the Reynolds-Averaged Navier-Stokes equations. The study focusses in particular on the specific plasma-related turbulence production in the equations governing the Reynolds-stress tensor. Prior to studying the airfoil configuration the computational determination of the body force and corresponding turbulence generation rate is analyzed in a wall jet flow induced by the DBD plasma actuator.     

Large eddy simulation and spectrum analysis of flow around two square cylinders arranged side by side

Large eddy simulation cooperated with the second order full extension ETG ( Euler-Taylor-Galerkin ) finite element method was applied to simulate the flow around two square cylinders arranged side by side at a spacing ratio of 1.5. The second order full extension ETG finite element method was developed by Wang and He. By means of Taylor expansion of terms containing time derivative, time derivative is replaced by space derivative. The function of it is equal to introducing an artificial viscosity term. The streamlines of the flow at different moments were obtained. The time history of drag coefficient, lift coefficient and the streamwise velocity on the symmetrical points were presented. Furthermore, the symmetrical problem of the frequency spectrum of flow around two square cylinders arranged side by side were studied by using the spectral analysis technology. The data obtained at the initialstage are excluded in order to avoid the influence of initial condition on the results. The power spectrums of drag coefficient, lift coefficient, the streamwise velocity on the symmetrical points were analyzed respectively. The results show that although the time domain process of dynamic parameters is nonsymmetrical, the frequency domain process of them is symmetrical under the symmetrical boundary conditions.     

Shadowgraph observations of the transition of the thermal boundary layer in a side-heated cavity

The transition of the thermal boundary layer from start-up to a quasi-steady state in a side-heated cavity is observed using a shadowgraph technique. Three stages of the transition, including an initial growth stage, an entrainment development stage and a quasi-steady stage, are demonstrated. A significant feature of the transition revealed from the present flow visualisation is the formation of a double-layer structure along the sidewall at the entrainment development stage. It is believed that the reverse flow in the double-layer structure is the likely cause responsible for the unstable travelling waves at the quasi-steady state.