Structural and optical properties of sprayed Zn1−xMnxO films

In recent years the dilute magnetic semiconductors have received much attention due to the complementary properties of semiconductor and ferromagnetic behaviour. Zn_1−xMn_xO thin films have been synthesized by chemical spray pyrolysis at a substrate temperature of 400 °C with different manganese compositions that vary in the range, 0.0 ≤ x ≤ 0.25, on Corning 7059 glass substrates. The X-ray diffraction studies revealed that all the films were strongly oriented along the (002) orientation corresponding to the hexagonal wurtzite structure. The crystalline quality of the layers was found to decrease with the increase of x, however, no structural changes were observed over the ‘Mn’ composition range investigated. The optical absorption studies revealed that the energy band gap of the films followed the Vegard's law. The optical band gap of the films prepared at x = 0.15 was found to be ∼3.35 eV. The photoluminescence characteristics of Zn_1−xMn_xO films showed an emission peak at around 390 nm with a broad band about 530 nm. The details of these results were reported and discussed.     

Exploration of spray pyrolysis technique in preparation of absorber material CFATS: Unprecedented hydrophilic surface and antibacterial properties

In this study, we achieve the production of nontoxic Cu₂Fe_1-xAl_xSnS₄ films (x = 0, 0.25, 0.50, 0.75 and 1) by substituting Fe with Al atoms. Physical properties of the investigated films were studied using: Energy dispersive X-ray spectrometry (EDX), scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman spectroscopy, spectrophotometer and drop shape analysis system (DSA). The formation of new quaternary Cu₃Al_0.6Sn₁S₆ (CATS) chalcogenide for x = 1 was proven from EDX study. Notably, the major diffraction peaks were located at 2θ = 28.34°, 47.43° and 55.93° which are respectively tagged as (1 1 2), (2 0 4), and (3 1 2) plans, confirming the stannite crystal structure of Cu₃Al_0.6Sn₁S₆ film. The morphological states show a nanofiber structure accompanied with voids and cavities for CATS films. Tauc-relation plot reveals direct energy bandgap, close to 1.52 eV, which proves the absorber film type of Cu₃Al_0.6Sn₁S₆. The effluent toxicity of the obtained thin films has been assessed using the inhibition of Gram-positive (Staphylococcus aureus) and Gram-negative (Escherichia coli) bacteria and indicated good antibacterial activity of the CATS/SnO₂:F heterojunction. The viability rates against S. aureus achieved 40 %, 31 % and 15% for SnO₂:F, Cu₃Al_0.6Sn₁S₆ films and CATS/SnO₂:F heterojunction. These results highlight the great antibacterial activity of coupled CATS/SnO₂:F. Therefore this research underscores the effectiveness of CATS/SnO₂:F surface which demonstrates self-disinfecting and self-cleaning with hydrophilicity and high antibacterial activity.     

Structure,microstructure and optical properties of cerium oxide thin films prepared by electron beam evaporation assisted with ion beams

Cerium oxide thin films were prepared by combined electron beam evaporation and ion beam assisted deposition techniques (EBE–IBAD). Their crystallographic structures, microstructures, and optical properties were studied as a function of the substrate temperature (200 °C and 500 °C) and the dose of Ar⁺ or O₂⁺ ion assistance during growth. X-ray diffraction was used to estimate the crystallographic texture, grain size, microstrain and lattice constant. Sample microstructure was studied by scanning electron microscopy. Transmission UV–vis spectroscopy was employed to obtain optical information (band gap, density, and refractive index). All films showed a cubic CeO₂ structure with different preferential growth depending on the preparation conditions. The bombardment with Ar⁺ ions during film deposition proved to be very effective for changing the film structure, hindering columnar growth and producing smaller grain sizes and higher values of microstrain and lattice constant. Films grown at 200 °C and Ar⁺ ion assistance showed the highest density, the smallest grain size (～10 nm) and a high expansion of the lattice constant (up to ～1%). This expansion is related to the presence of Ce³⁺ at the grain boundaries. Ion assistance during the growth leads to films with higher values of refractive index and lower values of band gap.     

Synthesis and properties of the compound: LiNi3/5Cu2/5VO4

The LiNi_3/5Cu_2/5VO₄ is synthesized by solution-based chemical method and its formation has been checked by X-ray diffraction (XRD) study. XRD study shows a tetragonal unit cell structure with lattice parameters of a = 11.6475 (18) Å, c = 2.4855 (18) Å and c/a = 0.2134 Å. Electrical properties are verified using complex impedance spectroscopy (CIS) technique. Complex impedance analysis reveals following points: (i) the bulk contribution to electrical properties up to 200 °C, (ii) the bulk and grain boundary contribution at T ≥ 225 °C, (iii) the presence of temperature dependent electrical relaxation phenomena in the material. D.c. conductivity study indicates that electrical conduction in the material is a thermally activated process.     

Effect of Deposition Temperature on Structural and Optical Properties of Chemically Sprayed ZnS Thin Films

Zinc sulfide (ZnS) thin films have been successfully deposited via spray pyrolysis using an aqueous solution of thiourea and zinc acetate onto glass substrate. The effect of varying substrate temperature (150, 200,250 and 300 °C) on structure and optical properties is presented. The films have been characterized by X- ray diffraction (XRD), UV-Vis-NIR spectrometry, photoluminescence (PL) spectroscopy and field emission scanning electron microscopy (FESEM). All the deposited ZnS films exhibit a cubic structure, while crystallinity and morphology are found to depend on spray temperature. PL analysis indicates the presence of violet and green emissions arising from Zn and S vacancies. The value of bandgap of ZnS films is found to decrease slightly with increasing substrate temperature; varying in the range 3.52–3.25 eV, most probably associated with the formation of Zn(S,O) solid solution.     

Synthesis,crystal structure and luminescent properties of pyrovanadates A2CaV2O7 (A = Rb,Cs)

The novel vanadium oxides Rb₂CaV₂O₇ and Cs₂CaV₂O₇ have been prepared by solid-state reaction and their crystal structures determined and refined using X-ray, neutron powder and electron diffraction data. Rb₂CaV₂O₇ and Cs₂CaV₂O₇ are isostructural, crystallizing in space group P2₁/n with unit cell parameters: a = 13.8780(1), b = 5.96394(5), c = 10.3376(1) Å, β = 104.960(1)° and a = 14.0713(2), b = 6.0934(1), c = 10.5944(1) Å, β = 104.608(1)°, respectively. Their crystal structures can be described as a framework of CaO₆ octahedra and V₂O₇ pyrogroups with alkaline metals found in the tunnels formed. Photoluminescence (PL) and PL excitation spectra of the considered pyrovanadates have been studied in the vacuum ultraviolet (VUV) to visible light (Vis) range as well as their pulse cathode luminescence (PCL) spectra and the kinetic parameters of PCL. In the PL and the PCL spectra of both pyrovanadates recorded at T = 300 K a broad band with maxima at 2.2, 2.4 eV and two shoulders (bands) at 2.0 and 2.58 eV have been observed. At T = 10 K the band at 2.0 eV becomes the main band in the spectra. Two types of luminescence centers for each pyrovanadate, with very similar excitation bands at 3.75, 4.84, 6.2, 7.3 and 9.1 eV, have been found. The nature of the luminescence centers connected with the bands at 2.0, 2.2, 2.4 and 2.58 eV is discussed.     

Doping effects of Yb3+ on the crystal structures,nanoparticle properties and electrical behaviors of ZrO2 derived from a facile urea-based hydrothermal route

Weakly-agglomerated nanocrystalline (ZrO₂)_1−x(Yb₂O₃)_x (x=0.02–0.2) powders with high surface area (109–151 m² g⁻¹) were synthesized by a two-step hydrothermal process in the presence of urea: a stock solution of metal nitrates and urea was heated at 80 °C for 24 h and then at 180 °C for 48 h. For x=0.04–0.2, the as-derived powders were an assembly of uniform nanoparticles with well-defined edges in the size between 6.1–8.4 nm. Before and after calcination at 800 °C, the lattice parameters, microstrain and surface area of the (ZrO₂)_1−x(Yb₂O₃)_x samples tended to increase with Yb³⁺ concentration; while, the average crystallite size decreased correspondingly. In the Arrhenius plots over the measurement temperature range of 400–800 °C, the bulk ionic conductivity of the compacts sintered at 1400 °C for 24 h showed a maximum value at the composition of x=0.08 in cubic structure, with an activation energy of 0.89 eV. At 800 °C, σ_b=0.049 S cm⁻¹ for x=0.08.     

New power source from fractional quantum energy levels of atomic hydrogen that surpasses internal combustion

Extreme ultraviolet (EUV) spectroscopy was recorded on microwave discharges of helium with 2% hydrogen. Novel emission lines were observed with energies of q·13.6 eV where q=1,2,3,4,6,7,8,9, or 11 or these lines inelastically scattered by helium atoms wherein 21.2 eV was absorbed in the excitation of He (1s²) to He (1s¹2p¹). These lines were identified as hydrogen transitions to electronic energy levels below the ‘ground’ state corresponding to fractional quantum numbers. Significant line broadening corresponding to an average hydrogen atom temperature of 33–38 eV was observed for helium–hydrogen discharge plasmas; whereas pure hydrogen showed no excessive broadening corresponding to an average hydrogen atom temperature of ≈3 eV. Since a significant increase in H temperature was observed with helium–hydrogen discharge plasmas, and energetic hydrino lines were observed at short wavelengths in the corresponding microwave plasmas that required a very significant reaction rate due to low photon detection efficiency in this region, the power balance was measured on the helium–hydrogen microwave plasmas. With a microwave input power of 30 W, the thermal output power was measured to be at least 300 W corresponding to a reactor temperature rise from room temperature to 900 °C within 90 s, a power density of 30 MW/m³, and an energy balance of about −4×10⁵ kJ/mol H₂ compared to the enthalpy of combustion of hydrogen of −241.8 kJ/mol H₂.     

Real structure of SrSi2O2N2

SrSi₂O₂N₂ is an important host lattice for Eu²⁺ doped phosphors. Its crystal structure (space group P1, a = 7.0802(2) Å, b = 7.2306(2) Å, c = 7.2554(2) Å, α = 88.767(3)°, β = 84.733(2)°, γ = 75.905(2)° and V = 358.73(2) Å³, Z = 4) is isotypic with EuSi₂O₂N₂: highly condensed silicate layers are separated by Sr²⁺. The samples are characterized by pronounced real structure effects owing to pseudosymmetry of partial structures. Polysynthetic twinning with domains of various sizes is ubiquitous and oriented intergrowth of domains with different orientations has also been observed and analysed in detail by means of electron diffraction and high-resolution electron microscopy. These effects also affect the X-ray powder pattern and were taken into account in a Rietveld refinement.     

Study of the morphology,thermal and mechanical properties of irradiated isotactic polypropylene films

Thin films of isotactic polypropylene (iPP) are of great economical importance and their production is quite challenging due to the need of very fast uniaxial or biaxial expansion. During the expansion, critical problems usually arise, like structure disruption, shear thinning, causing material, energy and time losses. This work aims to study the surface morphology and compare the thermal, mechanical properties of PP films irradiated by gamma ray in an acetylene atmosphere after uniaxial expansion. PP films were made by compression molding at 190 °C with cooling in water at room temperature and irradiated by gamma ray, at (5, 12.5 and 20 kGy) under acetylene atmosphere. After irradiation the samples were submitted to thermal treatment at 90 °C for 1 h and then stretched out at 170 °C using an Instron machine. The surface of PP films, pristine and modified, (i.e., irradiated), was studied using optical microscopy (OM) and scanning electron microscopy (SEM). The changes in morphology, crystallinity and tensile parameters, like yield stress, rupture stress and elongation strain of the PP with irradiation dose were investigated. The results showed some evidences of gel formation due to crosslinking and/or long chain branching induced by radiation.     

Dépôt de revêtements peu rugueux de diamant sur un alliage de titane

Deposition of smooth diamond coatings on titanium alloy. A new process has been perfected to deposit smooth diamond coatings, at 600 °C, on titanium alloys. Scanning electron microscopy, X-ray diffraction, visible and UV Raman spectroscopy show that these coatings are smooth and mainly composed of crystalline diamond with a fine-grained morphology. The results are compared here to those obtained with classical rough polycrystalline coatings. Optical emission spectroscopy reveals important differences between the plasma species produced for the deposition of these smooth coatings and the plasma species produced for the deposition of both polycrystalline diamond and nanocrystalline films. © 2000 Académie des sciences / Éditions scientifiques et médicales Elsevier SASdiamond / coating / titanium alloy / plasma / roughness / Raman spectroscopy / emission spectroscopy     

Enhanced electrical conductivity in Ce0.79Gd0.20Co0.01O2−δ for low temperature solid oxide fuel cell applications

Very high electrical conductivity of ～0.021 S/cm at 600 °C is obtained in Ce_0.79Gd_0.20Co_0.01O_2?δ. Corresponding activation energy of conduction ～0.43 eV measured in the temperature range of 400–700 °C is found to be notably low. Improved electrical properties with 99% of the theoretical density as obtained for these specimens, prepared using powder of average particle size ～20 nm and subsequent sintering at 1100 °C, is considered to be a significant step to reduce the processing temperature. The measured electrical potential of ～1 V indicates the suitability of its use as an electrolyte in electrochemical devices.     

Synthesis and photovoltaic property of polymer semiconductor with phthalimide derivative as a promising electron withdrawing material

Donor–acceptor type (DA-type) polymeric photovoltaic material with a dicarboxylic imide-substituted benzene (phthalimide) derivative as electron-withdrawing units, poly[4,4′-didodecyl-2,2′-bithiophene-co-5,5′-(3,6-bis(thieno-2-yl)-N-octyl-phthalimide] (PDBTTPT), was synthesized by a Stille coupling reaction. It had an optical band gap of 1.96 V and a relatively low HOMO energy level of ?5.34 eV in spite of it being a thiophene-based polymer. Photovoltaic devices with PDBTTPT/PC₇₁BM active layers were fabricated under a variety of conditions for optimizing device performance. PDBTTPT exhibited the best power conversion efficiency (PCE) of 1.5% in the device where 80 wt.% of the PC₇₁BM was contained in the active layer (PDBTTPT:PC₇₁BM = 1:4, w/w) and which was pre-annealed at 120 °C for 10 min. In addition, a device which was pre-annealed at 140 °C for 10 min and a device which was post-annealed at 120 °C for 10 min showed analogous PCE values of 1.5% as well, although small differences were exhibited between various parameters, such as V_OC, J_SC, and FF.     

Direct electrodeposition of PbTe thin films on n-type silicon

High quality lead telluride thin films were directly deposited onto n-type silicon (1 0 0) substrates by electrodeposition at room temperature. The deposition mechanism was studied using cyclic voltammetry. The films were characterized by scanning electron microscopy, energy dispersive X-ray, X-ray diffraction, and Fourier transform infrared spectroscopy. The results indicated that the deposited PbTe films exhibited a polycrystalline rock salt structure and good optical properties with a direct band gap of 0.31 eV.     

Dyed polyvinyl chloride films for use as high-dose routine dosimeters in radiation processing

Characteristics of the polyvinyl chloride (PVC) films containing 0.11 wt% of malachite green oxalate or 6GX-setoglausine and about 100 μm in thickness were studied for use as routine dosimeters in radiation processing. These films show basically color bleaching under irradiation with ⁶⁰Co γ-rays in a dose range of 5–50 kGy. The sensitivity of the dosimeters and the linearity of dose-response curves are improved by adding 2.5% of chloral hydrate [CCl₃CH(OH)₂] and 0.15% hydroquinone [HOC₆H₄OH]. These additions extend the minimum dose limit to 1 kGy covering dosimetry requirements of the quality assurance in radiation processing of food and healthcare products. The dose responses of both dyed PVC films at irradiation temperatures from 20°C to 35°C are constant relative to those at 25°C, and the temperature coefficients for irradiation temperatures from 35°C to 55°C were estimated to be (0.43±0.01)%/°C. The dosimeter characteristics are stable within 1% at 25°C before and 60 days after the end of irradiation.     

Biosynthesis of Bixa orellana seed extract mediated silver nanoparticles with moderate antioxidant,antibacterial and antiproliferative activity

Biosynthesis of metallic silver nanoparticles (AgNPs) has gained much interest and offers an attractive alternate to physical and chemical approaches. In recent year several safe, easy, cost-effective, reproducible, and environmentally friendly synthesis approaches for silver nanoparticles have been developed. In this research work, a simple, cheap, and unexplored method was applied on green synthesis of AgNPs using secondary metabolites extracted from Bixa orellana seeds. The seeds are rich of flavonoids and phenolic compounds which presumably responsible for the fast reduction and stabilization of silver ion into silver nanoparticles. The biosynthesis process is very likely to be able to reduce silver ions under simple physiological conditions. The surface plasmon resonance (SPR) that was appeared at 420 nm in UV–vis spectrum, had confirmed the formation of AgNPs. Moreover, the functional groups in secondary metabolite that act as reducing, capping and stabilizing agents for silver nanoparticles, are identified by Fourier transform infrared (FTIR) spectra. An X-ray diffraction analysis generated four peaks for Bixa orellana seed extract mediated AgNPs positioned at 2θ angles of 38.1°, 44.2°, 64.6°, and 77.5° corresponding to crystal planes (1 1 1), (2 0 0), (2 2 0), and (3 1 1). Field emission scanning electron microscope (FESEM) and transmission electron microscopy (TEM) images confirmed the formation of nanosized silver particles. The z-average of the synthesized particles measured by dynamic light scattering (DLS) was found to be 92.9 nm. AgNPs synthesized exhibited remarkable antioxidant activity, antibacterial and antiproliferative activity against human breast (MCF-7) cell line. On the basis of our results, we conclude that biologically synthesized AgNPs exhibited favorable characteristics and have the potential to be used in biomedical fields.     

Biosynthesized CuO nano-platelets: Physical properties & enhanced thermal conductivity nanofluidics

This contribution reports for the first time, room temperature biosynthesis of p-type CuO nanoparticles carried out using Callistemon viminalis’ flower extracts as a chelating agent in a process that is entirely green. Room temperature X-ray diffraction, attenuated IR total reflection spectroscopy, X-ray photoelectron and Raman spectroscopy investigations confirmed the formation of single phase Tenorite bcc monoclinic CuO nanocrystals post annealing in air, at 500 °C. Photoluminescence spectroscopy with UV emissions at 356 nm (3.47 eV) and broad visible emissions at 418 nm, 561 nm, and 664 nm, support the formation in air, at 200 °C, of CuO nanoparticles with high surface-to-volume ratios and defects. As a direct application, the biosynthesized CuO nanoplatelet-containing powder dispersed in de-ionized water showed an enhancement of the thermal conductivity from 6% to 34% and a significant stability of the PVP stabilized CuO-water nanofluid.     

A study on solution deposited CuSCN thin films: Structural,electrochemical, optical properties

A cost-effective successive ionic layer adsorption and reaction (SILAR) method was used to deposit copper (I) thiocyanate (CuSCN) thin films on glass and steel substrates for this study. The deposited thin films were characterized for their structural, morphological, optical and electrochemical properties using X-ray diffraction (XRD), scanning electron microscopy (SEM), UV–visible spectroscopy and VersaSTAT potentiostat. A direct band gap of 3.88 eV and 3.6 eV with film thickness of 0.7 μm and 0.9 μm was obtained at 20 and 30 deposition cycles respectively. The band gap, microstrain, dislocation density and crystal size were observed to be thickness dependent. The specific capacitance of the CuSCN thin film electrode at 20 mV/s was 760 F g⁻¹ for deposition 20 cycles and 729 F g⁻¹ for deposition 30 cycles.     

Synthesis and characterization of CaBi4Ti4O15 thin films annealed by microwave and conventional furnaces

CaBi₄Ti₄O₁₅ thin films were deposited by the polymeric precursor method and crystallized in a domestic microwave oven and conventional furnace. The films obtained for microwave energy are well-adhered, homogeneous and with good specularity when treated at 700 ^°C for 10 min. The microstructure and the structure of the films can be tuned by adjusting the crystallization conditions. When microwave oven is employed, the films presented bigger grains with mean grain size around 80 nm. For comparison, films were also prepared by the conventional furnace at 700 °C for 2 h.     

Phase transitions of CaTiO3 ceramics sintered with the aid of NaF and MgF2

New phases with initial composition (1 ? x)CaTiO₃ ? xNaF ? xMgF₂ (0 ≤ x ≤ 0.20) have been prepared at low temperature (950 °C) from mixtures of CaTiO₃ and fluorides NaF and MgF₂. The oxyfluorides obtained have been characterized by X-ray diffraction at room temperature and indexed by isotypy with orthorhombic CaTiO₃. The microstructures of these phases are observed by scanning electron microscopy. Dielectric measurements have been carried out during cooling cycle from 500 °C to room temperature at two frequencies (100 Hz, 1 kHz). Differential scanning calorimetry (DSC), thermogravimetry (TG) and differential thermogravimetry (DTG) analyses have been performed, respectively, from room temperature up to 550 °C (DSC) and 920 °C (TG–DTG). The dielectric measurements revealed two anomalies which have been confirmed by DSC analyses. These phenomena are ascribed to second order phase transitions. The variation of the real permittivity with temperature is in agreement with the class I capacitor specifications. However, the dielectric losses have to be improved.