Process optimization of ultrasound-assisted curcumin nanoemulsions stabilized by OSA-modified starch

This study reports on the process optimization of ultrasound-assisted, food-grade oil–water nanoemulsions stabilized by modified starches. In this work, effects of major emulsification process variables including applied power in terms of power density and sonication time, and formulation parameters, that is, surfactant type and concentration, bioactive concentration and dispersed-phase volume fraction were investigated on the mean droplet diameter, polydispersity index and charge on the emulsion droplets. Emulsifying properties of octenyl succinic anhydride modified starches, that is, Purity Gum 2000, Hi-Cap 100 and Purity Gum Ultra, and the size stability of corresponding emulsion droplets during the 1 month storage period were also investigated. Results revealed that the smallest and more stable nanoemulsion droplets were obtained when coarse emulsions treated at 40% of applied power (power density: 1.36 W/mL) for 7 min, stabilized by 1.5% (w/v) Purity Gum Ultra. Optimum volume fraction of oil (medium chain triglycerides) and the concentration of bioactive compound (curcumin) dispersed were 0.05 and 6 mg/mL oil, respectively. These results indicated that the ultrasound-assisted emulsification could be successfully used for the preparation of starch-stabilized nanoemulsions at lower temperatures (40–45 °C) and reduced energy consumption.     

Ultrasonic energy input influence οn the production of sub-micron o/w emulsions containing whey protein and common stabilizers

Ultrasonication may be a cost-effective emulsion formation technique, but its impact on emulsion final structure and droplet size needs to be further investigated. Olive oil emulsions (20 wt%) were formulated (pH ～ 7) using whey protein (3 wt%), three kinds of hydrocolloids (0.1–0.5 wt%) and two different emulsification energy inputs (single- and two-stage, methods A and B, respectively). Formula and energy input effects on emulsion performance are discussed. Emulsions stability was evaluated over a 10-day storage period at 5 °C recording the turbidity profiles of the emulsions. Optical micrographs, droplet size and viscosity values were also obtained. A differential scanning calorimetric (DSC) multiple cool–heat cyclic method (40 to ?40 °C) was performed to examine stability via crystallization phenomena of the dispersed phase.Ultrasonication energy input duplication from 11 kJ to 25 kJ (method B) resulted in stable emulsions production (reduction of back scattering values, dBS ～ 1% after 10 days of storage) at 0.5 wt% concentration of any of the stabilizers used. At lower gum amount samples became unstable due to depletion flocculation phenomena, regardless of emulsification energy input used. High energy input during ultrasonic emulsification also resulted in sub-micron oil-droplets emulsions (D₅₀ = 0.615 μm compared to D₅₀ = 1.3 μm using method A) with narrower particle size distribution and in viscosity reduction.DSC experiments revealed no presence of bulk oil formation, suggesting stability for XG 0.5 wt% emulsions prepared by both methods. Reduced enthalpy values found when method B was applied suggesting structural modifications produced by extensive ultrasonication. Change of ultrasonication conditions results in significant changes of oil droplet size and stability of the produced emulsions.     

Physicochemical characterization of black seed oil-milk emulsions through ultrasonication

The ultrasonic formation of stable emulsions of a bioactive material, black seed oil, in skim milk was investigated. The incorporation of 7% of black seed oil in pasteurised homogenized skim milk (PHSM) using 20 kHz high intensity ultrasound was successfully achieved. The effect of sonication time and acoustic power on the emulsion stability was studied. A minimum process time of 8 min at an applied acoustic power of 100 W was sufficient to produce emulsion droplets stable for at least 8 days upon storage at 4 ± 2 °C, which was confirmed through creaming stability, particle size, rheology and color analysis. Partially denatured whey proteins may provide stability to the emulsion droplets and in addition to the cavitation effects of ultrasound are responsible for the production of smaller sized emulsion droplets.     

Comparison of oil-in-water emulsions prepared by ultrasound,high-pressure homogenization and high-speed homogenization

This study was designed to compare the properties of myofibrillar protein (MP) stabilized soybean oil-in-water emulsions fabricated by ultrasound-assisted emulsification (UAE), high-pressure homogenization (HPH) and high-speed homogenization (HSH). The emulsion properties, droplet characteristics, interfacial proteins, protein exposure extent, microrheological properties, multiple light scattering results, and 7 d storage stabilities of the three emulsions were specifically investigated. Our results indicate that UAE and HPH were better emulsification methods than HSH to obtain high-quality emulsions with higher emulsifying activity index (UAE 20.73 m²·g⁻¹, HPH 11.76 m²·g⁻¹ and HSH 6.80 m²·g⁻¹), whiteness (UAE 81.05, HPH 80.67 and HSH 74.09), viscosity coefficient (UAE 0.44 Pa·sⁿ, HPH 0.49 Pa·sⁿ and HSH 0.22 Pa·sⁿ), macroscopic viscosity index (UAE 2.31 nm⁻²·s, HPH 0.38 nm⁻²·s and HSH 0.34 nm⁻²·s), and storage stability, especially for the UAE. Furthermore, UAE was a more efficient emulsification method than HPH to prepare the fine MP-soybean oil emulsion. The protein-coated oil droplets were observed in the three emulsions. The emulsion droplet size of the UAE-fabricated emulsion was the lowest (0.15 μm) while the interfacial protein concentration (93.37%) and the protein exposure extent were the highest among the three emulsions. During the 7 d storage, no separation was observed for the UAE-fabricated emulsion, while the emulsions fabricated by HPH and HSH were separated after storage for 5 d and 2 h. Therefore, this work suggests that UAE could be a better method than HPH and HSH to fabricate MP-soybean oil emulsion.     

Facile preparation and characterization of hollow poly(St-co-MMA-co-BA-co-MAA) core–double shell latex nanoparticles for electrophoretic displays

Novel core–double shell particles with poly(methyl methacrylate-co-butyl acrylate) (PMMA-co-BA) as the cores, poly(methyl methacrylate-co-butyl acrylate-co-methacrylic acid) (PMMA-co-BA-co-MAA) as the inner shells, poly(styrene-co-methyl methacrylate) (PS-co-MMA) as the outer shells were prepared by soap-free emulsion polymerization. The acid–alkali osmotic swelling processes were made before the outer shells wrapped for bigger aperture. The optimal experiment conditions were summarized. The morphology and size of the hollow latex particles were observed by transmission electron microscopy. The results showed that the uniform sizes of the hollow latex particles were about 230 nm. The electrophoretic mobility of them in tetrachloroethylene was 0.91 × 10⁻¹⁰ m² V⁻¹ s⁻¹, and the Zeta-potential was 5.87 mV. The results showed that the hollow polymer particles can used as background particles.     

High solids emulsions produced by ultrasound as a function of energy density

The use of emulsifying methods is frequently required before spray drying food ingredients, where using high concentration of solids increases the drying process yield. In this work, we used ultrasound to obtain kinetically stable palm oil-in-water emulsions with 30 g solids/100 g of emulsion. Sodium caseinate, maltodextrin and dried glucose syrup were used as stabilizing agents. Sonication time of 3, 7 and 11 min were evaluated at power of 72, 105 and 148 W (which represents 50%, 75% and 100% of power amplitude in relation to the nominal power of the equipment). Energy density required for each assay was calculated. Emulsions were characterized for droplets mean diameter and size distribution, optical microscopy, confocal microscopy, ζ-potential, creaming index (CI) and rheological behavior. Emulsions presented bimodal size distribution, with D_[3,2] ranging from 0.7 to 1.4 μm and CI between 5% and 12%, being these parameters inversely proportional to sonication time and power, but with a visual kinetically stabilization after the treatment at 148 W at 7 min sonication. D_[3,2] showed to depend of energy density as a power function. Sonication presented as an effective method to be integrated to spray drying when emulsification is needed before the drying process.     

Skin permeation of d-limonene-based nanoemulsions as a transdermal carrier prepared by ultrasonic emulsification

Nanoemulsions can be used for transporting pharmaceutical phytochemicals in skin-care products because of their stability and rapid permeation properties. However, droplet size may be a critical factor aiding permeation through skin and transdermal delivery efficiency. We prepared d-limonene nanoemulsions with various droplet sizes by ultrasonic emulsification using mixed surfactants of sorbitane trioleate and polyoxyethylene (20) oleyl ether under different hydrophilic–lipophilic balance (HLB) values. Droplet size decreased with increasing HLB value. With HLB 12, the droplet size was 23 nm, and the encapsulated ratio peaked at 92.3%. Transmission electron microscopy revealed spherical droplets and the gray parts were d-limonene precipitation incorporated in spherical droplets of the emulsion system. Franz diffusion cell was used to evaluate the permeation of d-limonene nanoemulsion through rat abdominal skin; the permeation rate depended on droplet size. The emulsion with the lowest droplet size (54 nm) achieved the maximum permeation rate. The concentration of d-limonene in the skin was 40.11 μL/cm² at the end of 360 min. Histopathology revealed no distinct voids or empty spaces in the epidermal region of permeated rat skin, so the d-limonene nanoemulsion may be a safe carrier for transdermal drug delivery.     

Enhanced photoacoustic imaging in tissue-mimicking phantoms using polydopamine-shelled perfluorocarbon emulsion droplets

The current work features process parameters for the ultrasound (25 kHz)-assisted fabrication of polydopamine-shelled perfluorocarbon (PDA/PFC) emulsion droplets with bimodal (modes at 100–600 nm and 1–6 µm) and unimodal (200–600 nm) size distributions. Initial screening of these materials revealed that only PDA/PFC emulsion droplets with bimodal distributions showed photoacoustic signal enhancement due to large size of their optically absorbing PDA shells. Performance of this particular type of emulsion droplets as photoacoustic agents were evaluated in Intralipid®–India ink media, mimicking the optical scattering and absorbance of various tissue types. From these measurements, it was observed that PDA/PFC droplets with bimodal size distributions can enhance the photoacoustic signal of blood-mimicking phantom by up to five folds in various tissue-mimicking phantoms with absorption coefficients from 0.1 to 1.0 cm⁻¹. Furthermore, using the information from enhanced photoacoustic images at 750 nm, the ultimate imaging depth was explored for polydopamine-shelled, perfluorohexane (PDA/PFH) emulsion droplets by photon trajectory simulations in 3D using a Monte Carlo approach. Based on these simulations, maximal tissue imaging depths for PDA/PFH emulsion droplets range from 10 to 40 mm, depending on the tissue type. These results demonstrate for the first time that ultrasonically fabricated PDA/PFC emulsion droplets have great potential as photoacoustic imaging agents that can be complemented with other reported characteristics of PDA/PFC emulsion droplets for extended applications in theranostics and other imaging modalities.     

Ion and electron conduction in SrFe1−xScxO3−δ

The oxygen ion and electron transport in SrFe_1−xSc_xO_3−δ  (x = 0.1–0.3) system at 700–950 °C were studied analyzing the total conductivity dependencies on the oxygen partial pressure, pO₂. The conductivity measurements were performed both under reducing conditions (10^− 19 ≤ pO₂ ≤ 10^− 8 atm) comprising the electron-hole equilibrium point, and in oxidizing atmospheres (10^− 5 ≤ pO₂ ≤ 0.5 atm) which are characterized by extensive variations of the oxygen content studied by coulometric titration technique. The incorporation of 10% Sc³⁺ cations into the iron sublattice suppresses transition of the cubic perovskite phase into vacancy-ordered brownmillerite, thus improving ion conduction at temperatures below 850 °C. When scandium content increases, the ion conductivity becomes considerably lower. The hole mobility is thermally-activated and varies in the range of 0.001 to 0.05 cm² V^− 1 s^− 1, increasing with oxygen concentration and decreasing on Sc doping.     

Sustained release formulations of citronella oil nanoemulsion using cavitational techniques

Nanoemulsion synthesis has proven to be an effective way for transportation of immobile, insoluble bioactive compounds. Citronella Oil (lemongrass oil), a natural plant extract, can be used as a mosquito repellent and has less harmful effects compared to its available market counterpart DEET (N, N-Diethyl-meta-toluamide). Nanoemulsion of citronella oil in water was prepared using cavitation-assisted techniques while investigating the effect of system parameters like HLB (Hydrophilic Lipophilic Balance), surfactant concentration, input energy density and mode of power input on emulsion quality. The present work also examines the effect of emulsification on release rate to understand the relationship between droplet size and the release rate. Minimum droplet size (60 nm) of the emulsion was obtained at HLB of 14, S/O¹ ratio of 1.0, ultrasound amplitude of 50% and irradiation time of 5 min. This study revealed that hydrodynamic cavitation-assisted emulsification is more energy efficient compared to ultrasonic emulsification. It was also found that the release rate of nanoemulsion enhanced as the droplet size of emulsion reduced.     

Characterization of LSGM films obtained by electrophoretic deposition (EPD)

The application of the electrophoretic deposition (EPD) technique to the preparation of high quality electrolyte films for intermediate temperature solid oxide fuel cells (IT-SOFCs) was investigated. Films of La_0.83Sr_0.17Ga_0.83Mg_0.17O_2.83 (LSGM) were deposited on Pt and La_0.8Sr_0.2MnO₃ (LSM) substrates from suspensions in acetone/ethanol (3:1 by volume) mixture solvent and sintered at 1300 °C. Pt supported LSGM films, 10–20 μm thick, exhibited good adhesion to the Pt substrate, well-distributed microporosity and some surface roughness. LSM supported films exhibited cracking after sintering at 1300 °C for 3 h. Up to 900 °C the bulk conductivity of the Pt supported LSGM film showed the same behaviour of LSGM pellet (E_a = 0.93 eV and 0.99 eV, respectively). The LSGM film exhibited lower bulk electrical conductivity than the latter (4.1 × 10^− 3 and 4.4 × 10^− 2 Ω^− 1 cm^− 1, respectively, at 700 °C). This difference should be ascribed to the slight Ga depletion in the LSGM film. An important issue remains the selection of adequate electrode for LSGM electrolyte films.     

Sonocatalytical degradation enhancement for ibuprofen and sulfamethoxazole in the presence of glass beads and single-walled carbon nanotubes

Sonocatalytic degradation experiments were carried out to determine the effects of glass beads (GBs) and single-walled carbon nanotubes (SWNTs) on ibuprofen (IBP) and sulfamethoxazole (SMX) removal using low and high ultrasonic frequencies (28 and 1000 kHz). In the absence of catalysts, the sonochemical degradation at pH 7, optimum power of 0.18 W mL⁻¹, and a temperature of 15 °C was higher (79% and 72%) at 1000 kHz than at 28 kHz (45% and 33%) for IBP and SMX, respectively. At the low frequency (28 kHz) H₂O₂ production increased significantly, from 10 μM (no GBs) to 86 μM in the presence of GBs (0.1 mm, 10 g L⁻¹); however, no enhancement was achieved at 1000 kHz. In contrast, the H₂O₂ production increased from 10 μM (no SWNTs) to 31 μM at 28 kHz and from 82 μM (no SWNTs) to 111 μM at 1000 kHz in the presence of SWNTs (45 mg L⁻¹). Thus, maximum removals of IBP and SMX were obtained in the presence of a combination of GBs and SWNTs at the low frequency (94% and 88%) for 60 min contact time; however, >99% and 97% removals were achieved for 40 and 60 min contact times at the high frequency for IBP and SMX, respectively. The results indicate that both IBP and SMX degradation followed pseudo-first-order kinetics. Additionally, the enhanced removal of IBP and SMX in the presence of catalysts was because GBs and SWNTs increased the number of free OH radicals due to ultrasonic irradiation and the adsorption capacity increase with SWNT dispersion.     

Hydrophilic polyaniline nanofibrous architecture using electrosynthesis method for supercapacitor application

An electrosynthesis process of hydrophilic polyaniline nanofiber electrode for electrochemical supercapacitor is described. The TGA–DTA study showed polyaniline thermally stable up to 323 K. Polyaniline nanofibers exhibit amorphous nature as confirmed from XRD study. Smooth interconnected fibers having diameter between 120–125 nm and length typically ranges between 400–500 nm observed from SEM and TEM analysis. Contact angle measurement indicated hydrophilic nature of polyaniline fibers. Optical study revealed the presence of direct band gap with energy 2.52 eV. The Hall effect measurement showed room temperature resistivity ∼3 × 10⁻⁴ Ω cm and Hall mobility 549.35 cm⁻²V⁻¹ s⁻¹_. The supercapacitive performance of nanofibrous polyaniline film tested in 1 M H₂SO₄ electrolyte and showed highest specific capacitance of 861 F g⁻¹ at the voltage scan rate of 10 mV/s.     

Impact of process parameters in the generation of novel aspirin nanoemulsions – Comparative studies between ultrasound cavitation and microfluidizer

In the present investigation, the operating efficiency of a bench-top air-driven microfluidizer has been compared to that of a bench-top high power ultrasound horn in the production of pharmaceutical grade nanoemulsions using aspirin as a model drug. The influence of important process variables as well as the pre-homogenization and drug loading on the resultant mean droplet diameter and size distribution of emulsion droplets was studied in an oil-in-water nanoemulsion incorporated with a model drug aspirin. Results obtained show that both the emulsification methods were capable of producing very fine nanoemulsions containing aspirin with the minimum droplet size ranging from 150 to 170 nm. In case of using the microfluidizer, it has been observed that the size of the emulsion droplets obtained was almost independent of the applied microfluidization pressure (200–600 bar) and the number of passes (up to 10 passes) while the pre-homogenization and drug loading had a marginal effect in increasing the droplet size. Whereas, in the case of ultrasound emulsification, the droplet size was generally decreased with an increase in sonication amplitude (50–70%) and period of sonication but the resultant emulsion was found to be dependent on the pre-homogenization and drug loading. The STEM microscopic observations illustrated that the optimized formulations obtained using ultrasound cavitation technique are comparable to microfluidized emulsions. These comparative results demonstrated that ultrasound cavitation is a relatively energy-efficient yet promising method of pharmaceutical nanoemulsions as compared to microfluidizer although the means used to generate the nanoemulsions are different.     

Oxygen nonstoichiometry and transport properties of strontium substituted lanthanum cobaltite

Oxygen nonstoichiometry, structure and transport properties of the two compositions (La_0.6Sr_0.4)_0.99CoO_3−δ (LSC40) and La_0.85Sr_0.15CoO_3−δ (LSC15) were measured. It was found that the oxygen nonstoichiometry as a function of the temperature and oxygen partial pressure could be described using the itinerant electron model. The electrical conductivity, σ, of the materials is high (σ > 500 S cm^− 1) in the measured temperature range (650–1000 °C) and oxygen partial pressure range (0.209–10^− 4 atm). At 900 °C the electrical conductivity is 1365 and 1491 S cm^− 1 in air for LSC40 and LSC15, respectively. A linear correlation between the electrical conductivity and the oxygen vacancy concentration was found for both samples. The mobility of the electron-holes was inversely proportional with the absolute temperature indicating a metallic type conductivity for LSC40. Using electrical conductivity relaxation the chemical diffusion coefficient of oxygen was determined. It was found that accurate values of the chemical diffusion coefficient could only be obtained using a sample with a porous surface coating. The porous surface coating increased the surface exchange reaction thereby unmasking the chemical diffusion coefficient. The ionic conductivity deduced from electrical conductivity relaxation was determined to be 0.45 S cm^− 1 and 0.01 S cm^− 1 at 1000 and 650 °C, respectively. The activation energy for the ionic conductivity at a constant vacancy concentration (δ = 0.125) was found to be 0.90 eV.     

Electrically forced microthreading of highly viscous dielectric liquids

The behaviour of three high viscosity (4875, 12 125 and 58 560 mPa s), dielectric liquids was investigated at flow rates of 10⁻¹⁰, 10⁻¹² and 10⁻¹⁴ m³ s⁻¹ and the applied voltage range 6–15 kV. In these experiments, due to the low electrical conductivity of the liquids (10⁻¹³ S m⁻¹) and therefore the ensuing high electrical relaxation time, classical electrohydrodynamic atomization conditions are not satisfied. Only dripping and unstable jetting were observed at 4875 mPa s. A transition from no jetting to stable microthreading was observed for the 12 125 and 58 560 mPa s samples. The relics accompanying the transition were found to change from discrete droplets to a continuous filament. Stable microthreading, which generates uniform filaments, was obtained for the 12 125 mPa s sample at flow rates 10⁻¹⁰ and 10⁻¹² m³ s⁻¹ and in the case of the 58 560 mPa s sample at all the flow rates investigated. The high viscosity assisted stable microthreading with the filament diameter decreasing with increasing applied voltage and more dramatically decreasing with reducing flow rate.     

Electrical transport and crystallization in Cu+ ion substituted AgI–Ag2O–V2O5 glassy superionic system

A new glassy solid electrolyte system Cu_xAg_1 − xI–Ag₂O–V₂O₅ has been synthesized. The structural, thermal and electrical properties of the samples have been investigated. The glassy nature of the samples is confirmed by X-Ray diffraction and Differential Scanning Calorimetry studies. The electrical conductivity of these samples increases with CuI content and approaches a maximum value of ∼ 10⁻² Ω^− 1 cm^− 1 for x = 0.35 at room temperature. Ionic mobility measurements suggest that enhancement in the conductivity with Cu⁺ ion substitution may be attributed to increase in the mobility of Ag⁺ ions. The electrical conductivity versus temperature cycles carried out at well-controlled heating rate above T_g and T_c reveal interesting thermal properties. For lower CuI content samples conductivity exhibits anomalous rise above T_g and subsequent fall at T_c. It is also found that CuI addition into AgI–Ag₂O–V₂O₅ matrix reduces the extent of crystallization.     

Transport and phase dynamics of poly(vinyl pyrrolidone) doped plastically crystalline N-methyl-N-propylpyrrolidinium tetrafluoroborate

The plastic crystal phase forming N-methyl-N-propylpyrrolidinium tetrafluoroborate organic salt (P₁₃BF₄) was combined with 2, 5 and 10 wt.% poly(vinyl pyrrolidone) (PVP). The ternary 2 wt.% PVP/2 wt.% LiBF₄/P₁₃BF₄ was also investigated. Thermal analysis, conductivity, optical thermomicroscopy, and Nuclear Magnetic Resonance (¹¹B, ¹⁹F, ¹H, ⁷Li) were used to probe the fundamental transport processes. Both the onset of phase I and the final melting temperature were reduced with increasing additions of PVP. Conductivity in phase I was 2.6 × 10^− 4 S cm^− 1 5.2 × 10^− 4 S cm^− 1 1.1 × 10^− 4 S cm^− 1 and 3.9 × 10^− 5 S cm^− 1 for 0, 2, 5 and 10 wt.%PVP/P₁₃BF₄, respectively. Doping with 2 wt.% LiBF₄ increased the conductivity by up to an order of magnitude in phase II. Further additions of 2 wt.% PVP slightly reduced the conductivity, although it remained higher than for pure P₁₃BF₄.     

Simulation of phase separation with large component ratio for oil-in-water emulsion in ultrasound field

This paper presents an exploration for separation of oil-in-water and coalescence of oil droplets in ultrasound field via lattice Boltzmann method. Simulations were conducted by the ultrasound traveling and standing waves to enhance oil separation and trap oil droplets. The focus was to the effect of ultrasound irradiation on oil-in-water emulsion properties in the standing wave field, such as oil drop radius, morphology and growth kinetics of phase separation. Ultrasound fields were applied to irradiate the oil-in-water emulsion for getting flocculation of the oil droplets in 420 kHz case, and larger dispersed oil droplets and continuous phases in 2 MHz and 10 MHz cases, respectively. The separated phases started to rise along the direction of sound propagation after several periods. The rising rate of the flocks was significantly greater in ultrasound case than that of oil droplets in the original emulsion, indicating that ultrasound irradiation caused a rapid increase of oil droplet quantity in the progress of the separation. The separation degree was also significantly improved with increasing frequency or irradiation time. The dataset was rearranged for growth kinetics of ultrasonic phase separation in a plot by spherically averaged structure factor and the ratio of oil and emulsion phases. The analyses recovered the two different temporal regimes: the spinodal decomposition and domain growth stages, which further quantified the morphology results. These numerical results provide guidance for setting the optimum condition for the separation of oil-in-water emulsion in the ultrasound field.     

Functional properties of ultrasonically generated flaxseed oil-dairy emulsions

This study reports on the functional properties of 7% flaxseed oil/milk emulsion obtained by sonication (OM) using 20 kHz ultrasound (US) at 176 W for 1–8 min in two different delivery formulae, viz., ready-to-drink (RTD) and lactic acid gel. The RTD emulsions showed no change in viscosity after sonication for up to 8 min followed by storage up to a minimum of 9 days at 4 ± 2 °C. Similarly, the oxidative stability of the RTD emulsion was studied by measuring the conjugated diene hydroperoxides (CD). The CD was unaffected after 8 min of ultrasonic processing. The safety aspect of US processing was evaluated by measuring the formation of CD at different power levels. The functional properties of OM gels were evaluated by small and large scale deformation studies. The sonication process improved the gelation characteristics, viz., decreased gelation time, increased elastic nature, decreased syneresis and increased gel strength. The presence of finer sono-emulsified oil globules, stabilized by partially denatured whey proteins, contributed to the improvements in the gel structure in comparison to sonicated and unsonicated pasteurized homogenized skim milk (PHSM) gels. A sono-emulsification process of 5 min followed by gelation for about 11 min can produce gels of highest textural attibutes.