Ultrasonication assisted and surfactant mediated synergistic approach for synthesis of calcium sulfate nano-dendrites

Calcium sulfate (CaSO₄) nano-dendrimers were fabricated successfully via ultrasonic irradiation method using calcium chloride [CaCl₂] and ammonium per sulfate [(NH₄)₂SO₄] as precursors in aqueous solution by using cetyl trimethyl ammonium bromide (CTAB) as chemical surfactants. Diffusion-induced branching growth mechanism (DIBGM), influenced with the action of head-group and hydrocarbon chain effect of cationic surfactants, was the backbone in the formation of CaSO₄ nano-dendrites. Fourier Transform Infra-red Spectroscopy (FTIR), X-Ray powder Diffraction (XRD), Atomic Emission Spectroscopy (AES), Selected Area Electron Diffraction (SAED), Field-Emission Scanning Electron Microscopy (FE-SEM), Energy-Dispersive Spectroscopy (EDS), Dynamic Light Spectroscopy (DLS) and BET surface area analyzer were used to characterize the products. Results obtained were compared with conventional stirring method that proved the superiority of sonication method to obtain well-crystalline nanostructures. Also, surfactant concentration, sonication frequency and time were noticed as the critical factors to generate such absolute morphologies at nano-crystalline size.     

Precipitation of calcium carbonate by ultrasonic irradiation

Supersaturated solution of calcium carbonate ([Ca²⁺]=1.2 mmol/L, [HCO₃⁻]=3.2 mmol/L, pH=8.8, T=30±0.5 °C), a scale forming component, was irradiated by an ultrasonic homogenizer (24 kHz, 15–250 W/cm²) to study the factors that affect its precipitation rate. The factors of (1) depth of horn immersion, (2) ultrasonic intensity and horn tip size and (3) cavitation, which can affect the precipitation rate were investigated in this study. Ultrasonic irradiation was observed to accelerate the precipitation of calcium carbonate and it was found that there exists an optimum range of horn immersion depth for maximizing the precipitation rate. The experimental data also established that the precipitation rate was proportional to ultrasonic intensity and diameter of horn tip. These findings were correlated to the effects of physical mixing, that arises due to ultrasonic irradiation. However, the effect of cavitation in accelerating the precipitation rate was found to be small. Thus it is forwarded that the physical mixing effect, especially macrostreaming is the main factor that accelerates the precipitation rate of calcium carbonate during ultrasonic treatment. Further, neither the morphology nor the size of the calcium carbonate crystals formed were found to be affected by the ultrasonic irradiation.     

超声对硫酸钙结晶过程影响的研究

研究了超声对硫酸钙结晶过程的影响。实验表明，与对比样相比，超声可以明显缩短成核时间，改变结晶量，影响结晶在不同方向的成长速度，使结晶的形状比例(长／宽)减小。粒度分布的定量测定和计算显示，超声使硫酸钙结晶粒度分布范围由200μm缩小到100μm，体积平均直径从69．9μm降到26．59μm；硫酸钙的成核速率提高2．74倍，但结晶成长速率减少到对比样的40．9％。两者番加的结果体现为结晶过程总速率的增加。     

Synthesis of dendritic silver nanostructures by means of ultrasonic irradiation

In this paper, a simple and effective route for the synthesis of silver dendritic nanostructures by means of ultrasonic irradiation has been developed. Well-defined silver dendritic nanostructures were obtained by sonicating the aqueous solution of 0.04 mol/L silver nitrate with 4.0 mol/L isopropanol as reducing agent and 0.01 mol/L PEG400 as disperser for 2 h. The effects of the irradiation time, the concentration of Ag⁺ and the molar ratio of PEG to AgNO₃ on the morphology of silver nanostructures were discussed. The structures of the obtained samples were characterized by transmission electron microscopy (TEM), selected area electron diffraction (SAED) and X-ray powder diffraction (XRD), and the chemical composition of the dendrites was examined by energy-dispersive X-ray spectrum (EDS).     

Decolorization of azo dye Orange G by aluminum powder enhanced by ultrasonic irradiation

In this work, the decolorization of azo dye Orange G (OG) in aqueous solution by aluminum powder enhanced by ultrasonic irradiation (AlP-UI) was investigated. The effects of various operating operational parameters such as the initial pH, initial OG concentration, AlP dosage, ultrasound power and added hydrogen peroxide (H₂O₂) concentration were studied. The results showed that the decolorization rate was enhanced when the aqueous OG was irradiated simultaneously by ultrasound in the AlP-acid systems. The decolorization rate decreased with the increase of both initial pH values of 2.0–4.0 and OG initial concentrations of 10–80 mg/L, increased with the ultrasound power enhancing from 500 to 900 W. An optimum value was reached at 2.0 g/L of the AlP dosage in the range of 0.5–2.5 g/L. The decolorization rate enhanced significantly by the addition of hydrogen peroxide in the range of 10–100 mM to AlP-UI system reached an optimum value of 0.1491 min⁻¹. The decolorization of OG appears to involve primarily oxidative steps, the cleavage of NN bond, which were verificated by the intermediate products of OG under the optimal tested degradation system, aniline and 1-amino-2-naphthol-6,8-disulfonate detected by the LC–MS.     

Ultrasonic assisted synergetic green synthesis of polycyclic imidazo(thiazolo)pyrimidines by using Fe3O4@clay core-shell

A practical and green approach for the ultrasound-enhanced one-pot multicomponent synthesis of tetraheterocyclic imidazo(thiazolo)pyrimidines is described via the condensation of an 2-aminobenzimidazole or 2-aminobenzothiazole, dimedone and various aldehydes in the presence of Fe₃O₄@clay as an environmentally benign and reusable core/shell nanocomposite catalyst in relatively quantitative yields. This novel eco-friendly protocol includes several advantages such as avoiding hazardous solvents, reusability of the catalyst, easy work-up, short reaction times, room temperature and mild reaction conditions. Furthermore, ultrasonic irradiation and synergistic catalyst showed considerable superiority vs. traditional heating or stirring conditions.     

Doping transition metal ions as a method for enhancement of ablation rate in femtosecond laser irradiation of silicate glass

We present a doping method to improve the femtosecond laser ablation rate and promote ablation selectivity. Doping transition metal ions, Co2＋ or Cu2＋, in silicate glass apparently change absorption spectroscopy and induce resonant absorption at wavelengths of 600 and 800 nm, respectively. Comparing with femtosecond laser processing of the same glass without doping, we find that the threshold fiuenee decreases and the ablation rate increases in resonant absorption in doped silicate glass. Resonant absorption effectively increases multiphoton ionization for seed-free electron generation, which in turn enhances avalanche ionization.     

Novel ionic liquid supported on Fe3O4 nanoparticles and its application as a catalyst in Mannich reaction under ultrasonic irradiation

A family of novel ionic liquid with l-alanine and choline chloride as environmentally benign materials have been synthesized and grafted on Fe₃O₄ nanoparticles using easy preparation techniques. The structure of ionic liquid supported on Fe₃O₄ nanoparticles (IL-Fe₃O₄ NPs) characterized by various analyses such as FE-SEM, EDX, XRD, NMR, FTIR and VSM. The catalytic activities of this catalyst are examined in the Mannich reaction for synthesis of β-aminocarbonyl compounds under ultrasonic irradiation. The recyclability of catalyst is investigated, and the results have indicated that the catalyst can be recycled six times without obvious activity decreasing.     

Sonochemical effect and pore structure tuning of silica xerogel by ultrasonic irradiation of semi-solid hydrogel

Silica xerogels were prepared by the sol-gel method under ultrasonic irradiation, using tetraethylorthosilicate (TEOS) as the starting material. Hexamethyldisiloxane (HMDSO) was used as the hydrophobizing agent. When preparing silica xerogel, it is necessary to perform aging and hydrophobization to suppress shrinkage during ambient pressure drying, however, such treatments are time-consuming. In this study, the semi-solid hydrogel was irradiated with ultrasonic for the first time in order to accelerate aging and hydrophobic treatment, and the effect of ultrasonic frequency on structure was investigated. Firstly, ultrasonic irradiation was performed at frequencies of 100 kHz and 500 kHz, followed by hydrophobic treatment at a frequency of 500 kHz, in order to promote aging. The results identify optimum conditions for ultrasonic irradiation to promote aging and hydrophobization reactions, and it was found to be possible to prepare silica xerogels in less than 1/5 of the conventional time. The silica xerogels had a low density and the shrinkage was suppressed. In this study, it was found that ultrasonic irradiation of semi-solid hydrogel was very effective for promoting the reaction.     

Characterization of nanoporous carbon fibrous materials obtained by chemical activation of plane tree seed under ultrasonic irradiation

An ultrasonic irradiation was applied for the impregnation by chemical agents in the chemical activation process of new type of active carbon precursor. Plane tree seed, due to the unique fibrous structure and low cost is a promising eco-friendly raw material for the preparation of activated carbon materials. Ultrasonic irradiation was used for the impregnation step allowing the chemical activation by different agents: potassium or sodium hydroxide, hydrogen peroxide and pyrogallol. The porous structures were examined by nitrogen adsorption/desorption isotherms at 77 K and electrochemically by cyclic voltammetry. The textures of these materials were observed by scanning electron microscopy. The application of ultrasonic irradiation in the impregnation step increased surface area of the final material more than two times in comparison to the material which impregnation in the activation process was by conventional stirring. Ultrasonic irradiation enhances the chemical activation process and the activated carbon fibrous materials with nanoporous structure were obtained by impregnation of seeds with alkaline hydroxides. Total surface areas of these samples were 976 m² g⁻¹ and 1130 m² g⁻¹. These fibers have total specific capacitance as high as 125 F g⁻¹ and 53 F g⁻¹ which major fraction in both cases originate from internal micropores structure.     

A novel approach for the synthesis of superparamagnetic Mn3O4 nanocrystals by ultrasonic bath

In this study, the synthesis of Mn₃O₄ (husmannite) nanoparticles was carried out in two different alkali media under sonication by ultrasonic bath and conventional method. Manganese acetate was used as precursor, sodium hydroxide and hexamethylenetetramine (HMT) as basic reagents in this synthesis. An ultrasonic bath with low intensity was used for the preparation of nanomaterials. The as prepared samples were characterized with X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, transmission electron microscopy (HRTEM, TEM), energy-dispersive spectrum (EDS), and superconducting quantum interference device (SQUID) analysis. The XRD patterns exhibit the nanocrystals are in pure tetragonal phase. The chemical composition was obtained by EDS analysis and confirmed the presence of Mn and O in the sample. According to the TEM and HRTEM results, both nanorods and nanoparticles of Mn₃O₄ were obtained in the presence of ultrasonic irradiation. The average size of nanoparticles was 10 nm, and the size of nanorods was 12 nm in diameter and 100-900 nm in length for the samples prepared in basic medium with sodium hydroxide. In the conventional method with the same basic medium, the nanorod was not observed and the nearly cubic nanoparticles was appeared with an average size of 2.5 nm. The selected area electron diffraction (SAED) patterns revealed that the nanocrystals are polycrystalline in nature. When HMT was used as a basic reagent in the presence of ultrasonic irradiation, it was led to a higher size of nanoparticles and nanorods than when sodium hydroxide was used as a basic reagent. The average size of nanoparticles was about 15 nm and its shape was nearly cubic. The diameter for nanorods was 50 nm and the length was about a few micrometers.The magnetic measurements were carried out on the sample prepared in sodium hydroxide under ultrasonic irradiation. These measurements as a function of temperature and field strength showed a reduction in ferrimagnetic temperature (T_c = 40 K) as compared to those reported for the bulk (T_c = 43 K). The superparamagnetic behavior was observed at room temperature with no saturation magnetization and hysteresis in the region of measured field strength.     

Poly(4-vinylpyridine) supported acidic ionic liquid: A novel solid catalyst for the efficient synthesis of 2,3-dihydroquinazolin-4(1H)-ones under ultrasonic irradiation

A novel poly(4-vinylpyridine) supported acidic ionic liquid catalyst was synthesized by the reaction of 4-vinylpyridine with 1,3-propanesultone, followed by the polymerization and the addition of the heteropolyacid. Due to the combination of polymer features and ionic liquid, it acted as a heterogeneous catalyst to effectively catalyze the cyclocondensation reaction of anthranilamide with aldehydes under ultrasonic irradiation and afforded the corresponding 2,3-dihydro-4(1H)-quinazolinones compounds in good to excellent yields. In addition, the catalyst could be easily recovered by the filtration and reused six times without significant loss of catalytic activity. More importantly, the use of ultrasonic irradiation can obviously accelerate the reaction.     

Sonocatalytic degradation of acid red B and rhodamine B catalyzed by nano-sized ZnO powder under ultrasonic irradiation

Nano-sized ZnO powder was introduced to act as the sonocatalyst after the treatment of high-temperature activation, and the ultrasound of low power was used as an irradiation source to induce nano-sized ZnO powder performing sonocatalytic degradation of acid red B and rhodamine B. At the same time, the effects of operational parameters such as solution pH value, initial concentration of dyestuff and addition amount of nano-sized ZnO powder have been examined in this paper. We found that the degradation ratios of acid red B and rhodamine B in the presence of nano-sized ZnO powder were much higher than that with only ultrasonic irradiation. However, the degradation ratio of acid red B was about two times higher than that of rhodamine B for the initial concentration of 10.0 mg/L, addition amount of 1.0 g/L nano-sized ZnO powder, solution acidity of pH 7.0 and 60 min irradiation experimental condition. The difference of the degradation ratios can be illustrated by the difference of chemical forms of acid red B and rhodamine B in aqueous solution and the surface properties of nano-sized ZnO particles. In addition, the researches on the kinetics of sonocatalytic reactions of acid red B and rhodamine B have also been performed and found to the follow pseudo first-order kinetics. All the experiments indicated that the sonocatalytic method in the presence of nano-sized ZnO powder was an advisable choice for the treatments of non- or low-transparent organic wastewaters in future.     

One-pot sonochemical synthesis of 1,3-thiazolidin-4-ones using nano-CdZr4(PO4)6 as a robust heterogeneous catalyst

An efficient three-component synthesis of 1,3-thiazolidin-4-ones is described by one-pot condensation of aldehydes, aniline and thioglycolic acid with nano-CdZr₄(PO₄)₆ as a robust heterogeneous catalyst under ultrasonic irradiation. Use of simple and readily available starting materials, experimental simplicity, applying the sonochemical methodology as an efficient method and innocuous means of activation in synthetic chemistry are some advantages of this protocol.     

Estimation of temperature elevation generated by ultrasonic irradiation in biological tissues using the thermal wave method

In most previous models,simulation of the temperature generation in tissue is based on the Pennes bio-heat transfer equation,which implies an instantaneous thermal energy deposition in the medium.Due to the long thermal relaxation time τ(20 s-30 s) in biological tissues,the actual temperature elevation during clinical treatments could be different from the value predicted by the Pennes bioheat equation.The thermal wave model of bio-heat transfer(TWMBT) defines a thermal relaxation time to describe the tissue heating from ultrasound exposure.In this paper,COMSOL Multiphysics 3.5a,a finite element method software package,is used to simulate the temperature response in tissues based on Pennes and TWMBT equations.We further discuss different factors in the bio-heat transfer model on the influence of the temperature rising and it is found that the temperature response in tissue under ultrasound exposure is a rising process with a declining rate.The thermal relaxation time inhibits the temperature elevation at the beginning of ultrasonic heating.Besides,thermal relaxation in TWMBT leads to lower temperature estimation than that based on Pennes equation during the same period of time.The blood flow carrying heat dominates most to the decline of temperature rising rate and the influence increases with temperature rising.On the contrary,heat diffusion,which can be described by thermal conductivity,has little effect on the temperature rising.     

Degradation of azo dye Acid black 1 using low concentration iron of Fenton process facilitated by ultrasonic irradiation

A combination of ultrasonic and low concentration iron (<3 mgL(-1)) of Fenton process (US/Fenton) has been used to treat wastewater containing Acid black 1 (AB1). The results show that the oxidation power of low concentration iron of Fenton could be significantly enhanced by ultrasonic irradiation. The degradation of AB1 in aqueous solution by US/Fenton can receive better results compared with either Fenton oxidation or ultrasonic alone. Many operational parameters, such as ultrasonic power density, the pH value, the Fe(2+) dosage, the H(2)O(2) dosage, AB1 concentration and the temperature, affecting the degradation efficiency were investigated. Also, the effects of various inorganic anions (such as Cl(-), NO(3)(-), CO(3)(2-), etc.) on the oxidation efficiency of US/Fenton were studied. Under the given test conditions, 98.83% degradation efficiency was achieved after 30 min reaction by US/Fenton. The effect of various inorganic anions was in the following decreasing order: SO(3)(2-)>CH(3)COO(-)>Cl(-)>CO(3)(2-)>HCO(3)(-)>SO(4)(2-)>NO(3)(-). The results show that the US/Fenton can be an effective technology for the treatment of organic dyes in wastewater.     

Ultrasonically-enhanced mechanochemical synthesis of CaAl-layered double hydroxides intercalated by a variety of inorganic anions

CaAl-layered double hydroxides (CaAl-LDHs) were synthesised with various interlayer anions (CO₃²⁻, F⁻, Cl⁻, Br⁻ and I⁻) by mechanochemical pre-treatment followed by ultrasonic irradiation in aqueous media. The parameters of the syntheses (duration of pre-milling and sonication, quality of the aqueous media, temperature) were altered in order to optimise the procedure and to understand the formation of LDH and other secondary products. The products were characterised by X-ray diffractometry (XRD) and scanning electron microscopy (SEM). The optimisation resulted in close-to-phase-pure CaAl-LDHs, not only with carbonate and chloride interlayer anions, but the hard-to-intercalate bromide and iodide as well.     

A facile one-pot ultrasound assisted for an efficient synthesis of benzo[g]chromenes using Fe3O4/polyethylene glycol (PEG) core/shell nanoparticles

In this research, a general synthetic method for the synthesis of benzo[g]chromenes has been developed using Fe₃O₄/polyethylene glycol (PEG) core/shell nanoparticle under ultrasonic irradiations. Compared to the conventional methods, ultrasound procedure showed several advantages including mild reaction conditions, high yield products, short reaction times, reusability of the catalyst and little catalyst loading.     

Stability and characterization of mesoporous molecular sieve using natural clay as a raw material obtained by microwave irradiation

Mesoporous molecular sieve was synthesized via microwave irradiation method, and using natural clay, sodium silicate and aluminum chloride as raw materials and cetyl trimethyl ammonium bromide (CTAB) as a template agent under alkaline condition. The samples were characterized by various analytic and spectroscopic tools such as XRD, FT-IR, TEM, TG-DSC and N₂ physical adsorption, respectively. The results show that the synthesized sample has typical mesoporous structure and exhibits good mesoporous ordering. On the other hand, the as synthesized sample after calcination at 550 °C for 10 h has a surface area of 576.0 m²/g and an average pore size of 4.83 nm. Furthermore, the synthesized mesoporous molecular sieve still exhibits good mesoporous ordering after calcination at 750 °C for 3 h or hydrothermal treatment at 100 °C for 10 days.     

Combined of ultrasound irradiation with high hydrostatic pressure (US/HHP) as a new method to improve immobilization of dextranase onto alginate gel

In this research work, dextranase was immobilized onto calcium alginate beads by the combination of ultrasonic irradiation and high hydrostatic pressure (US/HHP) treatments. Effects of US/HHP treatments on loading efficiency and immobilization yield of dextranase enzyme onto calcium alginate beads were investigated. Furthermore, the activities of immobilized enzymes prepared with and without US/HHP treatments and that prepared with ultrasonic irradiation (US) and high hydrostatic pressure (HHP), as a function of pH, temperature, recyclability and enzyme kinetic parameters, were compared with that for free enzyme. The maximum loading efficiency and the immobilization yield were observed when the immobilized dextranase was prepared with US (40 W at 25 kHz for 15 min) combined with HHP (400 MPa for 15 min), under which the loading efficiency and the immobilization yield increased by 88.92% and 80.86%, respectively, compared to immobilized enzymes prepared without US/HHP treatment. On the other hand, immobilized enzyme prepared with US/HHP treatment showed V_max, K_M, catalytic and specificity constants values higher than that for the immobilized enzyme prepared with HHP treatment, indicated that, this new US/HHP method improved the catalytic kinetics activity of immobilized dextranase at all the reaction conditions studied. Compared to immobilized enzyme prepared either with US or HHP, the immobilized enzymes prepared with US/HHP method exhibited a higher: pH optimum, optimal reaction temperature, thermal stability and recyclability, and lower activation energy, which, illustrating the effectiveness of the US/HHP method. These results indicated that, the combination of US and HHP treatments could be an effective method for improving the immobilization of enzymes in polymers.