Electrokinetic supercharging preconcentration and microchip gel electrophoretic separation of sodium dodecyl sulfate-protein complexes

A microchip gel electrophoresis (MCGE) method with electrokinetic supercharging (EKS, electrokinetic injection with transient isotachophoresis) on a single channel chip was developed for high-sensitive detection of a standard mixture of six proteins (phosphorylase b, albumin, ovalbumin, carbonic anhydrase, trypsin inhibitor, and alpha-lactalbumin) in the form of sodium dodecyl sulfate (SDS) complexes. An average lower limit of detectable concentration (LLDC) achieved using UV detection at 214 nm was 0.27 microg/mL that is 30 times lower than that of conventional MCGE on a cross geometry chip. The calibration curves for molecular weight and concentration of SDS-protein complexes suggested that the present EKS-MCGE method had a better linear dynamic range and benefited future applications for qualitative and quantitative analysis of unknown protein samples. It was found that an excessive amount of unbound SDS in the sample deteriorated the preconcentration effect and resolution. The developed method appears greatly promising for high-speed and high sensitive analysis of SDS-proteins by MCGE.     

Electronic gel protein transfer and identification using matrix-assisted laser desorption/ionization-mass spectrometry

An electronic protein transfer technique is described for achieving the rapid and efficient recovery of sodium dodecyl sulfate (SDS)-protein complexes from polyacrylamide gels. This process involves the use of small-dimension capillaries in physical contact with a resolved protein band within the polyacrylamide gel, providing a large potential drop and high electric field strength at the capillary/gel interface. Several factors controlling the electronic protein transfer, including the applied electric field strength, the electrophoresis buffer concentration, and the capillary dimension, are studied to further enhance the use of field-amplification for sample stacking of extracted SDS-protein complexes. As a result of sample stacking, the extracted proteins from a 50 ng gel loading are present in a narrow ( approximately 80 nL) and highly concentrated (0.46 mg/mL or 3.3 x 10(-5) M for cytochrome c) solution plug. Three model proteins with molecular mass ranging from 14 kDa (cytochrome c) to 116 kDa (beta-galactosidase) are stained by Coomassie blue and electrophoretically extracted from gels with protein loadings as low as 50 ng. The capillary format of the electronic protein transfer technique allows direct deposition of extracted proteins onto a matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) target. Various matrices and solvent compositions are evaluated for the analysis of extracted and concentrated SDS-protein complexes using MALDI-MS. The electronic protein transfer technique, when operated under optimized conditions, is demonstrated for the effective (>70% recovery), speedy (less than 5 min), and sensitive MS identification of gel resolved proteins (as low as 50 ng).     

Resolution of 8-aminonaphthalene-1,3,6-trisulfonic acid-labeled glucose oligomers in polyacrylamide gel electrophoresis at low gel concentration

A discontinuous Tris-Cl/acetate (OAc) buffer system, unprecedently containing OAc as the trailing constituent, and operative in polyacrylamide gel electrophoresis (PAGE) at low polyacrylamide concentration (T = 4.8%) is described in the paper. The characteristics of the electrophoretic system are illustrated by the resolution of fluorescent 8-aminonaphthalene-1,3,6-trisulfonic acid (ANTS)-labeled malto-oligosaccharides and dextran homopolymers. In this buffer system, the resolving phase is constituted by Tris-OAc behind a moving boundary formed between the leading chloride ion of Tris-HCl gel buffer and the trailing OAc ion provided by a catholyte of NH(4)OAc. In contrast with the results obtained with Tris-CI/glycinate buffer commonly used in electrophoresis, or with Tris-CI/borate, the best resolution of the glucose oligomers containing 1-4 glucose units in Tris-OAc, pH 8.8, ionic strength of 0.08, was obtained at 4.8% polyacrylamide concentration, using 0.5 M NH(4)OAc, pH 9.5 as the catholyte. Under those conditions, the ANTS-glucose oligomers were separated with mobilities decreasing from glucose to maltohexaose. The linear Ferguson plots (log relative mobility, R(f), vs.%T) of the glucose oligomers show that the surface net charge of those oligomers is inversely related to their sizes, given by the slopes, K(R), of the plots. The molecular weight of the oligomers is directly but nonlinearly related to K(R). The novel electrophoretic system illustrated here for separation of short ANTS-saccharides can be potentially applied to the resolution of other biomolecules such as rapidly migrating DNA, peptides or proteins.     

Ultrathin-layer sodium dodecyl sulfate gel electrophoresis of proteins: effects of gel composition and temperature on the separation of sodium dodecyl sulfate-protein complexes

This paper discusses the effects of gel composition and separation temperature on the migration properties of fluorescein-5-isothiocyanate-labeled protein molecular mass markers (ranging from 20 100 to 205 000 Da) in automated ultrathin-layer sodium dodecyl sulfate (SDS) gel electrophoresis. The separation mechanism with the agarose and composite agarose - linear polyacrylamide, agarose - hydroxyethyl cellulose, and agarose - polyethylene oxide matrices were all found to comply with the Ogston sieving model in the molecular mass range of the protein molecules investigated. Our temperature studies revealed that electrophoretic separation of SDS protein complexes is an activated process and, in pure agarose and in composite agarose hydroxyethyl cellulose and agarose - polyethylene oxide matrices that the separation requires increasing activation energy as a function of the molecular mass of the separated proteins. On the other hand, when linear polyacrylamide was used as composite additive, the activation energy demand of the separation decreased with increasing solute molecular mass. The sensitivity of the laser-induced fluorescent detection of the automated ultrathin-layer electrophoresis system was evaluated by injecting a series of dilutions of the markers and was found to be less than 2.5 ng/band for the fluorophore-labeled protein.     

Simultaneous electrophoretic analysis of proteins of very high and low molecular mass using Tris‐acetate polyacrylamide gels

To separate and analyze giant and small proteins in the same electrophoresis gel, we have used a 3–15% polyacrylamide gradient gel containing 2.6% of the crosslinker bisacrylamide and 0.2 M of Tris‐acetate buffer (pH 7.0). Samples were prepared in a sample buffer containing lithium dodecyl sulphate and were run in the gel described above using Tris‐Tricine‐SDS‐sodium bisulfite buffer, pH 8.2, as electrophoresis buffer. Here, we show that this system can be successfully used for general applications of SDS‐PAGE such as CBB staining and immunoblot. Thus, by using Tris‐acetate 3–15% polyacrylamide gels, it is possible to simultaneously analyze proteins, in the mass range of 10–500 kDa, such as HERC1 (532 kDa), HERC2 (528 kDa), mTOR (289 kDa), Clathrin heavy chain (192 kDa), RSK (90 kDa), S6K (70 kDa), β‐actin (42 kDa), Ran (24 kDa) and LC3 (18 kDa). This system is highly sensitive since it allows detection from as low as 10 μg of total protein per lane. Moreover, it has a good resolution, low cost, high reproducibility and allows for analysis of proteins in a wide range of weights within a short period of time. All these features together with the use of a standard electrophoresis apparatus make the Tris‐acetate‐PAGE system a very helpful tool for protein analysis.     

Electrophoresis in one buffer at two pH values

A theory for discontinuous electrophoresis in a polyacrylamide gel is presented for one buffer at two pH values. It is shown that polyions stack between identical leading and trailing ions, and resolve in a gel of constant polyacrylamide concentration. The theory is illustrated by the separation of serum protein polyions in a Tris-glycinate buffer of pH 8.19 in the well-forming gel, and pH 9.16 in the resolving gel. The selected concentrations and electrolyte ionization degrees of Tris and glycine have values at which the serum protein polyions stack between the resolving and electrode buffers, followed by separation in the resolving gel.     

Gel electrophoresis of native actin and the actin-deoxyribonuclease I complex

Electrophoresis of monomeric actin (G-actin) on 8-25% acrylamide Pharmacia PhastGels was carried out using gels and agarose buffer strips preequilibrated in buffer containing adenosine triphosphate (ATP), calcium ions (Ca2+) and dithiothreitol. On these gels G-actin ran as a sharp band at an apparent molecular mass of 45 kDa relative to standard proteins which is slightly greater than its actual molecular mass of 42 kDa. Electrophoresis in the absence of these solutes led to denaturation and aggregation of the protein, as reflected by a long streak. Filamentous actin (F-actin) did not enter the gel. The actin monomer-binding protein, deoxyribonuclease I, (DNase I) forms a binary complex with G-actin. The purity and apparent molecular mass 74 kDa of this complex were determined by native gel electrophoresis. By the simple procedure of preequilibrating both gel and buffer strips with appropriate ligands, this technique could be extended to investigate interactions between actin and other G-actin-binding proteins and other proteins whose stability is ligand dependent.     

Electrophoretic characterization of a novel cysteine protease produced by Vibrio harveyi

Electrophoretic characterization of a novel cysteine protease produced by pathogenic luminous Vibrio harveyi, originally isolated from diseased tiger prawn Penaeus monodon in Taiwan, is demonstrated in the present study using native polyacrylamide gel electrophoresis (native PAGE), sodium dodecyl sulfate-PAGE (SDS-PAGE), crossed immunoelectrophoresis (CIE) and isoelectric focusing (IEF) gels. The protease has a pI of 6.4 and exhibits a fast-migrating feature in native-PAGE and CIE gels indicating that it is a negatively charged protease. The protease electrophoresed as a 22 kDa protein band in native- and SDS-PAGE (in SDS - buffer with or without the presence of 2-mercaptoethanol) while it electrophoresed as a 38 kDa protein band in SDS-PAGE when the samples were boiled for 10 min prior to electrophoresis. The results reveal that the enzyme is an SDS-resistant monomeric protease and its high negative charge is not influenced by SDS (detergent) without boiling the sample. The present results are useful in determining proteins of similar nature to this unique cysteine protease.     

Sieving of ionic constituents across moving boundaries in gel electrophoresis

The representative beta-hydroxyethylmorpholinium-chloride-bicinate moving boundary with a trailing ion net mobility relative to Na+ of 0.41, detected by precipitation of chloride with silver nitrate, exhibits a decreasing chloride mobility at increasing polyacrylamide gel concentrations from 3.5 to 45%T, 5%CBis. This decrease, largely due to an increase of field strength at constant current, is described by a convex* plot of log (mobility) vs. %T (Ferguson plot) and signifies that chloride/bicinate are sieved by the gel. In agarose gels, the same plot of mobility vs. gel concentration is constant below 7% gel concentration, since in those gels field strength and migration rate remain the same within that gel concentration range. Both in polyacrylamide and in agarose gels the displacement rate of the chloride-bicinate boundary as a function of the time of electrophoresis or distance migrated remains invariant within 15%. The plot of log (mobility) vs. gel concentration extrapolated to 0%T is 5.85 and 5.41 (10(-5) cm2s-1V-1) for polyacrylamide and for agarose (SeaKem HGT-P,FMC) gels, respectively. The slightly decreased mobility intercept at 0%T for agarose is presumably due either to the electroendosmotic properties of agarose HGT-P and/or failure to Sufficiently take into account the flattening of the Ferguson plot in the polyacrylamide concentration range below 3% in which a transition from a gel to a fluid (sol) medium takes place.     

Rapid analysis of covalently and non-covalently fluorophore-labeled proteins using ultra-thin-layer sodium dodecylsulfate gel electrophoresis

Gel electrophoresis is one of the most frequently used tools for the separation of complex biopolymer mixtures. In recent years, there has been considerable activity in the separation and characterization of protein molecules by sodium dodecylsulfate (SDS) gel electrophoresis with particular interest in using this technique to separate on the basis of size and to estimate molecular mass and protein purity. Although the method is informative, it is cumbersome, time consuming and lacks automation. In this paper we report an automated, high-performance SDS gel electrophoresis system that is based on electric-field-mediated separation of SDS-protein complexes using an ultra-thin-layer platform. The integrated fiber optic bundle-based scanning laser-induced fluorescence detection technology readily provided high sensitivity, real-time detection of the migrating solute molecules. Rapid separations of covalently and non-covalently labeled proteins were demonstrated in the molecular mass range 14,000 to 205,000 in less than 9 and 16 min, respectively. Excellent quantitation and lane-to-lane migration time reproducibility were found for all the solute components using the multilane separation platform. The limit of detection was found to be 1.5-3 ng/band for both labeling methods, with excellent linearity over a six times serial double-dilution range. Molecular mass calibration plots were compared for both covalently and non-covalently labeled proteins. A linear relationship was found between the molecular mass and electrophoretic mobility in the case of covalently labeled samples, while a non-linear relationship was revealed for the non-covalently labeled samples.     

Development of a novel two-dimensional gel electrophoresis protocol with agarose native gel electrophoresis

A new protocol for conducting two-dimensional (2D) electrophoresis was developed by combining the recently developed agarose native gel electrophoresis with either vertical sodium dodecyl sulfate (SDS) polyacrylamide gel electrophoresis (PAGE) or flat SDS agarose gel electrophoresis. Our innovative technique utilizes His/MES buffer (pH 6.1) during the first-dimensional (1D) agarose native gel electrophoresis, which allows for the simultaneous and clear visualization of basic and acidic proteins in their native states or complex structures. Our agarose gel electrophoresis is a true native electrophoresis, unlike blue native–PAGE, which relies on the intrinsic charged states of the proteins and their complexes without the need for dye binding. In the 2D, the gel strip from the 1D agarose gel electrophoresis is soaked in SDS and placed on top of the vertical SDS–PAGE gels or the edge of the flat SDS–MetaPhor high-resolution agarose gels. This allows for customized operation using a single electrophoresis device at a low cost. This technique has been successfully applied to analyze various proteins, including five model proteins (BSA, factor Xa, ovotransferrin, IgG, and lysozyme), monoclonal antibodies with slightly different isoelectric points, polyclonal antibodies, and antigen–antibody complexes, as well as complex proteins such as IgM pentamer and β-galactosidase tetramer. Our protocol can be completed within a day, taking approximately 5–6 h, and can be expanded further into Western blot analysis, mass spectrometry analysis, and other analytical methods.     

Shotgun electroelution: a proteomic tool for simultaneous sample elution from whole SDS-polyacrylamide gel slabs

A high-throughput device has been constructed which allows parallel electroelution of separated SDS-protein bands directly from intact unsectioned polyacrylamide gel slabs as well as single electroelution of certain protein spots into a 384-well standard flat-bottom multiwell plate. The prototype provides complete, quick elution for proteomics from 1-D or from 2-D gels without gel sectioning. Since the elution chamber matrix requires no assembly, sample handling can be easily carried out by existing robotic workstations. The current design is a good candidate for automation of spot elution since there are no moving liquid containing components in the apparatus. Eight SDS-proteins were eluted in test runs and an average 70% sample recovery was achieved by re-electrophoresis of the electro-eluates.     

On-line isotachophoretic preconcentration and gel electrophoretic separation of sodium dodecyl sulfate-proteins on a microchip

A microchip for integrated isotachophoretic (ITP) preconcentration with gel electrophoretic (GE) separation to decrease the detectable concentration of sodium dodecyl sulfate (SDS)-proteins was developed. Each channel of the chip was designed with a long sample injection channel to increase the sample loading and allow stacking the sample into a narrow zone using discontinuous ITP buffers. The pre-concentrated sample was separated in GE mode in sieving polymer solutions. All the analysis steps including injection, preconcentration, and separation of the ITP-GE process were performed continuously, controlled by a high-voltage power source with sequential voltage switching between the analysis steps. Without deteriorating the peak resolution, four SDS-protein analyses with integrated ITP-GE system resulted in a decreased detectable concentration of approximately 40-fold compared to the GE mode only. A good calibration curve for molecular weights of SDS-proteins indicated that the integrated ITP-GE system can be used for qualitative analysis of unknown protein samples.     

Sequential electroelution and mass spectroscopic identification of intact sodium dodecyl sulfate-proteins labeled with 5(6)-carboxyfluorescein-N-hydroxysuccinimide ester

A gel electrophoresis apparatus capable of scanning the migration path fluorometrically and of computer-directed electroelution of bands was applied to the mass spectrometric identification of sequentially electroeluted 5(6)-carboxyfluorescein-N-hydrosuccinimide ester (FLUOS)-labeled sodium dodedyl sulfate (SDS)-proteins. The masses of four electroeluted SDS-proteins under study determined by matrix assisted laser desorption/ionization-time of flight (MALDI-TOF) spectrometry are changed by 1% due to their reaction with FLUOS in a 1:5 molar ratio of protein:label, allowing for the identification of the labeled intact proteins on the basis of mass. More importantly, the partial (10 or 50%) derivatization of proteins with FLUOS does not preclude their tryptic hydrolysis, and identification of the protein on the basis of the mass spectrometric analysis of its tryptic peptides. Potentially, the procedure allows for the automated mass spectrometric identification of SDS-proteins globally labeled with FLUOS and electrophoretically separated, without need for any gel sectioning.     

Interactions of hemoglobin in live red blood cells measured by the electrophoresis release test

To elucidate the protein–protein interactions of hemoglobin (Hb) variants A and A₂, HbA was first shown to bind with HbA₂ in live red blood cells (RBCs) by diagonal electrophoresis and then the interaction between HbA and HbA₂ outside the RBC was shown by cross electrophoresis. The starch–agarose gel electrophoresis of hemolysate, RBCs, freeze‐thawed RBCs and the supernatant of freeze‐thawed RBCs showed that the interaction between HbA and HbA₂ was affected by membrane integrity. To identify the proteins involved in the interaction, protein components located between HbA and HbA₂ in RBCs (RBC HbA‐HbA₂) and hemolysate (hemolysate HbA‐HbA₂) were isolated from the starch–agarose gel and separated by 5–12% SDS‐PAGE. The results showed that there was a ≈22 kDa protein band located in the RBC HbA‐HbA₂ but not in hemolysate HbA‐HbA₂. Sequencing by LC/MS/MS showed that this band was a protein complex that included mainly thioredoxin peroxidase B, α‐globin, δ‐globin and β‐globin. Thus, using our unique in vivo whole blood cell electrophoresis release test, Hbs were proven for the first time to interact with other proteins in the live RBC.     

Membrane-assisted online renaturation for automated microfluidic lectin blotting

Aberrant glycosylation plays a pivotal role in a diverse set of diseases, including cancer. A microfluidic lectin blotting platform is introduced to enable and expedite the identification of protein glycosylation based on protein size and affinity for specific lectins. The integrated multistage assay eliminates manual intervention steps required for slab-gel lectin blotting, increases total assay throughput, limits reagent and sample consumption, and is completed using one instrument. The assay comprises non-reducing sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE) followed by online post-sizing SDS filtration and lectin-based affinity blotting. Important functionality is conferred through both device and assay advances that enable integration of nanoporous membranes flanking a central microchamber to create sub-nanoliter volume compartments that trap SDS-protein complexes and allow electrophoretic SDS removal with buffer exchange. Recapitulation of protein binding for lectin was optimized through quantitative assessment of SDS-treated green fluorescent protein. Immunoglobulin A1 aberrantly glycosylated with galactose-deficient O-glycans was probed in ~6 min using ~3 μL of sample. This new microfluidic lectin blotting platform provides a rapid and automated assay for the assessment of aberrant glycosylation.     

Discontinuous buffer system for polyacrylamide and agarose gel electrophoresis of DNA fragments

DNA fragments up to 9 kb in size were stacked and separated by polyacrylamide gel electrophoresis, and those up to 50 kb in size by agarose gel electrophoresis, using a discontinuous buffer system. Polyacrylamide gels at pH 8.9, 2 degrees C, 0.01 M ionic strength, yielded sharp bands with DNA loads of 8 micrograms/cm2 of gel of a mixture of 19 DNA fragments in the size range of 72-23130 bp, while agarose gels at pH 8.5, 25 degrees C, provided well-resolved, unperturbed bands at 0.04 M ionic strength with DNA loads of 1 microgram/cm2 of the same mixture. Note that the ionic strength of the agarose gels is comparable to the conventionally used 0.5 x TBE (Tris-borate-EDTA) buffer, while that successfully applied to polyacrylamide is seven-fold less than the ionic strength of conventionally used 1 x TBE buffer, with a substantially shorter duration of electrophoresis as a result. The application of a discontinuous buffer system to the gel electrophoresis of DNA results in (i) Band identification by Rf, the migration distance relative to a sharply defined "buffer front" (moving boundary). This is sufficiently labor saving, compared to determining absolute mobilities, so as to render practical the expression of bands as numbers, with benefits for data storage, statistical manipulations and physico-chemical exploitation of mobility data. The use of Rf's also circumvents loss of precision in mobility measurement resulting from progressive band spreading of dye bands used as a front. (ii) A uniformly and highly concentrated starting zone, beneficial to resolution, is obtained, without the losses by which separate concentration steps are usually burdened.(ABSTRACT TRUNCATED AT 250 WORDS)     

Moving boundaries in sodium dodecyl sulfate-polyacrylamide gel electrophoresis

In sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE), moving boundaries I-IV (Table 1) form. They migrate isotachophoretically at displacement rates that increase in the order of I to II to III. Moving boundaries IV and V comprising Pyronin-SDS as a leading constituent are retarded at high gel concentrations in comparison with the isotachophoretically migrating species. Since analytes depending on their net mobilities stack within any of those moving boundaries, previous R(f) values and Ferguson plots may have to be revised.     

Stacking due to ionic transport number mismatch during sample sweeping on microchips

Sample stacking can occur in isoconductive buffer systems as a result of ion transport mismatches that cause changes in buffer conductivity during electrophoresis. Fluorescence imaging was used to examine this effect in the sweeping of hydrophobic dyes with sodium dodecyl sulfate (SDS) on microchips. Imaging revealed the occurrence of a stacking effect in a sodium borate buffer system in which the sample buffer and SDS-containing run buffer had the same initial conductivity. Injected sample plugs were first swept by SDS micelles and the swept band was then stacked at the trailing end of the sample zone. This effect is due to changes in conductivity at both the front and back interfaces of the injected sample plug and can be modeled by moving boundary equations. Maximum signal enhancements of 86-, 160- and 560-fold were obtained for Rhodamine 560, Rhodamine B and Rhodamine 6G, respectively, by the combination of sweeping and stacking within a 1 cm section of microchannel. Based on sample sweeping/stacking and manipulation of the electric field polarity, a method of trapping and concentrating analyte from multiple injections was also demonstrated.     

Ultrathin-layer sodium dodecyl sulfate disc electrophoresis of proteins in the range from 10 to 220 kDa in homogeneous,low-concentrated polyacrylamide gels

This study describes an ultrathin-layer sodium dodecyl sulfate (SDS) disc electrophoresis in polyacrylamide gels of a thickness of only 150 microm. By use of 2-amino-2-methyl-1,3-propanediol/glycine instead of traditional Tris/HCl buffer in the resolving phase of the gel, proteins with a wide range of molecular sizes (10 kDa to over 220 kDa) are separated in unusually low-concentrated gels (4%T, 3.3%C). 2-Amino-2-methyl-1,3-propanediol in the resolving part of the gel contributes to stabilization of the pH value at 8.8, while glycine improves destacking as well as separation of small proteins from the bulk of stacked SDS. This method combines both the advantages of conventional slab-gel electrophoresis and capillary gel electrophoresis. It is easy to apply and well suited for all further miniaturization attempts.