Singly resonant optical parametric oscillation in periodically poled lithium niobate waveguides

We report quasi-phase-matched singly resonant optical parametric oscillation in electric-field-poled lithium niobate waveguides. Parametric gains as high as 250%/W, an oscillation threshold of 1.6 W (peak), idler output powers of 220 mW, and a tuning range of 1180-2080 nm for pump wavelengths of 756-772 nm have been observed. Pump depletion is limited to 40% because of the multiple launched transverse modes at the pump wavelength. We predict that fully optimized waveguide singly resonant oscillators can have thresholds of ~100 mW, accessible to cw diode pumping.     

Angle-tuned signal-resonated optical parametric oscillator based on periodically poled lithium niobate

We demonstrate an angle-tuned signal-resonated optical parametric oscillator (OPO) with periodically poled lithium niobate (PPLN) pumped by a diode-pumped Nd:YVO4 laser. 1499.8 - 1506.6 nm of signal wavelength is achieved at 140℃ by rotating a 29-μm period PPLN from 0° - 10.22° in the x-y plane while keeping the pump wave vertical to the resonator mirrors. Two pairs of the signal and idler waves of the same wavelengths can be achieved symmetrically for each pair of angles of rotation with same absolute value and opposite sign. Theoretical analyses on angle-tuned PPLN-OPO with pump wave vertical to the resonator mirrors are presented and in good agreement with our experimental results. It is also found that all interacting waves in the cavity (not inside the crystal) are always collineax for PPLN-OPO with the pump wave vertical to the resonator mirrors while phase-matching is noncollinear within the crystal.     

High-power picosecond optical parametric oscillator based on periodically poled lithium niobate

A high-power picosecond optical parametric oscillator (OPO) based on a 47-mm periodically poled lithium niobate crystal is described. More than 12 W of total average power-almost 8 W of signal power at 1.85 microm and more than 4 W of idler radiation at 2.5 microm -is simultaneously extracted from less than 18 W of average pump power. The OPO is synchronously pumped by 80-ps (FWHM) cw mode-locked pulses at 1.064 microm , and its output is tunable from 1.7 to 2.84microm . Nearly transform-limited signal pulses are obtained following the introduction of two intracavity etalons.     

Fabrication of periodically poled lithium niobate chips for optical parametric oscillators

An electric-field poling process was established that yielded uniform periodically poled lithium niobate (PPLN) in 0.5 mm thick lithium niobate substrate. We have fabricated 50 mm long fanned as well as multigrating PPLNs having period variations from 25 μm to 32 μm. These PPLNs are required for quasi-phase-matched (QPM) optical parametric oscillator (OPO) applications. We have also configured a bench-top OPO set-up based on these PPLNs.     

Cascaded optical parametric oscillation with a dual-grating periodically poled lithium niobate crystal

We demonstrate continuous-wave cascaded optical parametric oscillation in which the signal field of the primary parametric oscillator internally pumps the secondary parametric oscillator. Wavelength tuning is achieved with temperature tuning and a fan-out grating structure of a dual-grating periodically poled lithium niobate crystal. Above the secondary threshold the primary signal power is clamped, and all the other output powers increase linearly with the input pump power, in accordance with theory. Cascaded parametric oscillation offers a convenient and efficient way to generate multiple tunable outputs.     

周期性极化铌酸锂晶体光参量振荡调谐与容差特性分析

研究了周期性极化铌酸锂晶体光参量振荡的工作机理,并讨论了其波长调谐特性与极化反转光栅周期、抽运光波长与晶体温度的关系.在此基础上,通过对相位失配因子求微分的方案,分析了光参量振荡的增益与光栅周期、抽运光波长与晶体温度的关系,以及光栅周期、抽运光波长与晶体温度容差的关系 关键词： 准相位匹配 周期性极化铌酸锂 光参量振荡     

Frequency-agile kilohertz repetition-rate optical parametric oscillator based on periodically poled lithium niobate

We report kilohertz repetition-rate pulse-to-pulse wavelength tuning from 3.22 to 3.7 mum in a periodically poled lithium niobate (PPLN) optical parametric oscillator (OPO). Rapid tuning over 400 cm(-1) with random wavelength accessibility is achieved by rotation of the pump beam angle by no more than 24 mrad in the PPLN crystal by use of an acousto-optic beam deflector. Over the entire tuning range, a near-transform-limited OPO bandwidth can be obtained by means of injection seeding with a single-frequency 1.5-mum laser diode. The frequency agility, high repetition rate, and narrow bandwidth of this mid-IR PPLN OPO make it well suited as a lidar transmitter source.     

Continuous wave monolithic quasi-phase-matched optical parametric oscillator in periodically poled lithium niobate

We demonstrate a monolithic and quasi-phasematched singly resonant cw optical parametric oscillator in periodically poled lithium niobate. The threshold is 1.0 W and the OPO delivers up to 0.98 W signal power tunable between 1750 and 1950 nm (2710 and 2340 nm idler, respectively). We identify cascaded parasitic oscillation effects and analyze their behavior theoretically, showing good agreement with our experiment. The analysis of parasitic effects points the way to improved device designs that should enable stable, compact, and frequency-tunable sources.     

Self-optical parametric oscillation in periodically poled neodymium-doped lithium niobate

Self-optical parametric oscillation is demonstrated for the first time to our knowledge in a periodically poled neodymium-doped lithium niobate (Nd:PPLN) crystal. The crystal is pumped by a cw Ti:sapphire laser at 813.5 nm. The Nd(3+) ions absorb the 813.5-nm radiation to generate 1084-nm laser oscillation. The internally Q switched 1084-nm radiation pumps the periodically poled lithium niobate host matrix to generate optical parametric oscillation at 1.55 and 3.6 microm . Up to 24% conversion efficiency from laser to signal is observed.     

Broadly tunable mid-infrared femtosecond optical parametric oscillator using all-solid-state-pumped periodically poled lithium niobate

We describe a high-repetition-rate femtosecond optical parametric oscillator (OPO) that was broadly tunable in the mid infrared. The all-solid-state-pumped OPO was based on quasi-phase matching in periodically poled lithium niobate. The idler was tunable from approximately 1.7 mum to beyond 5.4 mum, with maximum average power levels greater than 200 mW and more than 20 mW of average power at 5.4 mum. We used interferometric autocorrelation to characterize the mid-infrared idler pulses, which typically had durations of 125 fs. This OPO had a pumping threshold as low as 65 mW of average pump power, a maximum conversion efficiency of >35% into the near-infrared signal, a slope efficiency for the signal of approximately 60%, and a maximum pump depletion of more than 85%.     

Continuous-wave mid-infrared intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate

This paper reports a continuous-wave (CW) mid-infrared intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate (PPLN) pumped by a diode-end-pumped CW Nd:YVO$_{4}$ laser. Considering the thermal lens effects, it adopted an optical ballast lens and the near-concentric cavity for better operation. At the PPLN's grating period of 28.5\,$\mu$m and the temperature of 140\du, the maximum idler output power of 155\,mW at 3.86\,$\mu$m has been achieved when the 808\,nm pump power is 8.5\,W, leading to an optical-to-optical conversion efficiency of 1.82{\%}.     

Aperture scaling effects with monolithic periodically poled lithium niobate optical parametric oscillators and generators

We used elliptical beams to demonstrate aperture scaling effects in nanosecond single-grating and multigrating periodically poled lithium niobate (PPLN) monolithic optical parametric oscillators and generators. Increasing the cavity Fresnel number in single-grating crystals broadened both the beam divergence and the spectral bandwidth. Both effects are explained in terms of the phase-matching geometry. These effects are suppressed when a multigrating PPLN crystal is used because the individual gratings provide small effective subapertures. A flood-pumped multigrating optical parametric generator displayed a low output beam divergence and contained 19 pairs of signal and idler frequencies.     

Continuous-wave 532-nm-pumped singly resonant optical parametric oscillator based on periodically poled lithium niobate

We report a continuous-wave (cw) 532-nm-pumped singly resonant optical parametric oscillator (SRO) based on periodically poled lithium niobate. The pump source is a commercial 5-W cw diode-pumped, multilongitudinal-mode, intracavity-doubled Nd:YVO(4) laser. Using a four-mirror ring SRO cavity and single-pass pumping, we achieved subwatt internal oscillation threshold, 56% quantum efficiency, and output tuning from 917 to 1266 nm.     

Continuous-wave mid-infrared intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate

This paper reports a continuous-wave （CW） mid-infrared intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate （PPLN） pumped by a diode-end-pumped CW Nd：YVO4 laser. Considering the thermal lens effects, it adopted an optical ballast lens and the near-concentric cavity for better operation. At the PPLN＇s grating period of 28.5 μm and the temperature of 140℃, the maximum idler output power of 155 mW at 3.86 μm has been achieved when the 808 nm pump power is 8.5 W, leading to an optical-to-optical conversion efficiency of 1.82%.     

Periodically poled lithium niobate optical parametric amplifier seeded with the narrow-band filtered output of an optical parametric generator

The results of a simple scheme to generate continuously tunable pulsed narrow-bandwidth (less than 0.1 cm (-1)) light in the infrared are presented. A periodically poled lithium niobate (PPLN) optical parametric amplifier is seeded with the filtered output of a PPLN optical parametric generator. A high-finesse Fabry-Perot etalon is used as the filtering element, giving bandwidths as narrow as 0.08 cm (-1) and tunable over 18 cm (-1) without any adjustments to the PPLN crystals. High efficiency is obtained with a 15-ns 1-kHz Nd:YAG laser, giving energies of up to 180 microJ of signal at 1.6 microm and 60 microJ of idler at 3.3 microm .     

High-efficiency,high-repetition-rate,temperature-tuning optical parametric oscillator based on periodically poled MgO-doped lithium niobate

We report a compact and viable source of high-efficiency, high-repetition-rate, temperature-tuning, mid-IR optical parametric oscillator (OPO) based on periodically poled MgO-doped lithium niobate (PPMgOLN) pumped by a homemade high power AOM Q-switched Nd:YVO₄ laser centered at 1.064 μm. With an optimal plane-concave resonator configuration, average output power of 5.7 W at 2.73 μm was obtained when the pump power was 25 W at the repetition rate of 80 kHz. The conversion efficiency from the 1.064 μm laser to the 2.73 μm laser was 22.8%. Temperature tuning of the OPO yielded a signal wavelength range from 1.67 to 1.75 μm and an idler wavelength in the range of 2.72 to 2.92 μm.     

Synchronously pumped femtosecond optical parametric oscillator of congruent and stoichiometric MgO-doped periodically poled lithium niobate

A synchronously pumped femtosecond optical parametric oscillator based on congruent MgO-doped periodically poled lithium niobate (c-MgO:PPLN) is reported. The system, operating at room temperature, was pumped by a mode-locked Ti:sapphire laser. The wavelengths of the signal and idler waves were tuned from 870 nm to 1.54 μm and 1.58 to 5.67 μm, respectively, by changing the pump wavelength, the grating period or the cavity length. Pumped by 1.1 W of 755 nm laser radiation, the OPO generated 310 mW of 1080 nm radiation. This signal output corresponds to a total conversion efficiency of 50%. Without dispersion compensation the OPO generated phase-modulated signal pulses of 200 fs duration. Besides the OPO of c-MgO:PPLN, an OPO of stoichiometric (s) MgO:PPLN was investigated. Because of the reduced sensitivity to photorefractive damage, both crystals allowed efficient OPO operation at room temperature. Received: 19 August 2002 / Revised version: 11 December 2002 / Published online: 19 March 2003 RID="*" ID="*"Corresponding author. Fax: +49-631/205-3906, E-mail: andres@physik.uni-kl.de     

Distributed-feedback optical parametric oscillation by use of a photorefractive grating in periodically poled lithium niobate

We report a demonstration of distributed-feedback (DFB) optical parametric oscillation (OPO) by writing photorefractive gratings in periodically poled lithium niobate (PPLN). The photorefractive DFB structures were fabricated by illumination of PPLN with UV light through a photomask and by writing of PPLN with UV-light gated interfering laser beams at 532 nm. Evidence of OPO was observed from the spectral narrowing at the 1438.8- and the 619.3-nm signal wavelengths from 1064- and 532-nm-pumped PPLN crystals with the DFB grating periods phase matched to the 4084.5- and 3774-nm idler wavelengths, respectively.     

Collinear broadband optical parametric generation in periodically poled lithium niobate crystals by group velocity matching

Collinear broadband optical parametric generation (OPG) using periodically poled lithium niobate (PPLN) crystals were designed and experimentally demonstrated with the quasi-phase matching (QPM) periods of 21.5, 24.0, and 27.0 μm. The broad gain bandwidth was accomplished by choosing a specific set of the period and the pump wavelength that allows the group velocities of the signal and the idler to match close to the degeneracy point. OPG gain bandwidth and also the spectral region could be controlled by proper design of QPM period and pump wavelength. The total OPG gain bandwidth of 600, 900, and 1200 nm was observed for the PPLN devices with QPM periods of 21.5, 24.0, and 27.0 μm, respectively. We have also observed multiple color visible generation whenever the OPG spectrum was significantly broad. From the visible peaks of the three PPLN samples, it is found that broad gain bandwidth is crucial in the temperature-insensitive collinear simultaneous RGB generation from a single crystal.