Disjoining pressure and stratification in asymmetric thin-liquid films

We directly measure, for the first time, disjoining pressure isotherms for asymmetric oil/aqueous surfactant/gas (i.e., pseudoemulsion) films using a modified version of the porous-plate technique first developed by Mysels in conjunction with thin-film interferometry. Dynamic film-thinning experiments are also performed on individual foam and pseudoemulsion films. At SDS surfactant concentrations above the critical micelle concentration (CMC) (0.1 M SDS), the pesudoemulsion films exhibit the same step-wise layer thinning observed in foam films under similar conditions. Further, we conduct dynamic thinning experiments on solid/liquid/gas systems and show that aqueous 0.2 M CTAB films sandwiched between glass and air also display discrete thinning transitions. All of these stratification transitions arise from oscillations in the disjoining pressure isotherm, generated by amphiphilic structuring within the film.For 0.1 M SDS dedecane/air pesudoemuslion films, the slope and peak height of the disjoining-pressure oscillations increase with each subsequent amphiphilic layer as film thickness decreases. Magnitudes of the structural forces are low (<100 Pa) but the length scale of the oscillations is large (10 nm) and rathe far reaching (50 nm). Moreover, for 0.1 M SDS solutions, the capillary pressures associated with film rupture are significantly lower for pseudoemulsion films (0.1 kPa) when compared to foam films (15 kPa) at equivalent conditions. Taken together, our dynamic thinning and equilibrium disjoining pressure measurements indicate that stratification in 0.1 M SDS films has little effect on both kinetic and thermodynamic films stability.     

Disjoining pressure in a symmetric circular slit

Local disjoining pressure has been calculated for dispersion forces inside a symmetric circular plane-parallel empty slit. In contrast to the asymmetric case, the local disjoining pressure in a symmetric slit is defined unambiguously. The edge effects in the symmetric slit have been shown to be substantially stronger than those in the asymmetric one. The data obtained have been compared with the published results of the approximate calculation of averaged disjoining pressure. The approximate approach has been revealed to underestimate the absolute value of the correction to the averaged disjoining pressure by nearly 10%.     

Saturated vapor pressure in the thallium-cadmium system

Component vapor pressures in the thallium-cadmium system determined by the method of boiling points (isothermal variant) and the flow method were used to calculate the thermodynamic characteristics of the vapor and condensed phases in the region of the existence of liquid solutions. The temperature-concentration dependences of the thermodynamic values were determined. The phase diagram was augmented by liquid-vapor phase transitions at atmospheric pressure and in a vacuum (100 and 10 Pa) with the determination of the boundaries for the coexistence region of the liquid and vapor phases.     

Mass transfer,mixing and heat transfer phenomena in low viscosity bubble column reactors

Bubble columns are widely used in chemical and biotechnological process industries. The important reasons for this wide usage are the simple construction, without moving parts, and the high energy efficiency for mass transfer. It is not surprising therefore that much research on this subject has been published, yet selecting material of practical use is rather difficult. To overcome this problem, in this review, attempts are made to extract formulae and guidelines as simply as possible on the basis of currently available material.The starting point is the mechanisms occurring in bubble columns, i.e. bubble formation, bubble rise and resulting circulation patterns. Once these phenomena are understood, mixing and heat and mass transfer are much easier to deal with. Bubble formation is largely dependent on the sparger type, which can be divided into three groups: single orifices, porous discs and two-phase injectors. The original bubble diameter together with the superficial velocity and liquid properties determine the bubble diameter, holdup and circulation patterns in the bubble column. Gas holdup, bubble diameter control k_LA and circulation patterns determine mixing and heat transfer. Simple relations are derived for model systems. By means of a mechanistic approach, guidelines are given for more complex liquids.     

Experimental investigation of heat transfer and exergy loss in heat exchanger with air bubble injection technique

Journal of Thermal Analysis and Calorimetry - The main aim of this study is to evaluate thermal performance and exergy analysis of a shell-and-tube heat exchanger with a new technique called air...     

Disjoining pressure in a plane-parallel asymmetric slit with finite sizes

An approach has been developed to calculation of the Irving-Kirkwood pressure tensor inside a circular plane-parallel empty slit between bodies with dispersion forces. The disjoining pressure is determined as the normal component of the pressure tensor on a slit wall and is found as a function of both the width and radius of the slit. It has been shown that, at a preset slit width, the disjoining pressure acquires a value almost equal to that inherent in an infinitely long slit already at a circular slit radius five times larger than the slit width.     

Disjoining pressure,contact angles and line tension in free thin liquid films

Three are the main thermodynamic quantities which characterize the physical behaviour of the thin liquid films: the disjoining pressure, the macroscopic contact angle between the film and its adjacent bulk liquid phase, and the line tension of the film contact perimeter. All these quantities manifest the action of the long-range interaction surface forces which take place in any small capillary system. The rigorous introduction of such quantities is closely related to the Gibbs concept of surface of tension. For the case of a thin plane parallel liquid film there exist three surfaces of tension. By making use of them the thickness of the film would also be defined. There are several experimental methods for determining the tension of film, the contact angles. the line tension. Some important details of these methods. some experimental results together with important features of the thermodynamic theory of the thin liquid films are the subject of the present paper.     

Condensation of a vapor bubble in submicrometer container

Condensation of a spherically symmetric submicrometer size vapor bubble is studied using diffuse interface hydrodynamic model supplemented by the van der Waals equation of state with parameters characteristic for argon. The bubble, surrounded by liquid, is held in a container of constant volume with temperature of the wall kept fixed. The condensation is triggered by a sudden rise of the wall temperature. We find that in the same container and subjected to a similar increase of the wall temperature the condensation process is totally different from the opposite process of droplet evaporation. In particular, the rapid change of the wall temperature excites the wave, which hits the interface and compresses the bubble, leading to a considerable increase of the temperature inside. The condensation of the submicrometer size bubble takes tens of nanoseconds, whereas evaporation of the same size droplet lasts roughly 50 times longer. In contrast to evaporation the condensation process is hardly quasistationary.     

Evaluation of thermal analysis equipment for the determination of vapor pressure and heat of vaporization

A rapid, relatively simple method for determining vapor pressure and heat of vaporization on small amounts of organic compounds is described. A DuPont 900 differential thermal analyzer (DTA), a Perkin—Elmer Model DSC-1B differential scanning calorimeter (DSC), and a Thomas—Hoover (TH) melting point apparatus were evaluated in this work. Vapor pressure data for a wide variety of organic liquids were obtained by measuring the boiling points of the liquids at pressures ranging from 20 to 735 torr. A computer was used to rapidly plot the experimental data. The average deviations of boiling points from the literature values were 2.3°C for the DTA 1.2°C for the DSC, and 1.5°C for the TH. The vapor pressure data were used to solve the Haggenmacher equation for heat of vaporization (ΔH_v). The deviations of the experimental values for ΔH_v. from the literature values were 5.5%, 8.3%. and 3.3% for the DTA, DSC, and TH methods, respectively.     

鼓泡浆态反应器中浸没表面的传热研究

在内径98mm的鼓泡浆态反应器内,考察了工艺参数对浸没表面与浆液间的传热系数的影响。浆态反应器轴向装有一个外径20mm,长120mm的测量传热膜系数用的铜制元件。为了模拟浆态FT合成反应系统,三相系统由N2、液体石蜡和石英砂（平均粒径53μm、110μm、180μm）或63μm以下的Fe2O3组成。工艺参数变化范围如下：表观气速0.005m/s～0.08m/s, 温度353K～453K, 压力0.1MPa～0.8MPa,固体的质量分数0～20%,初始液位高度625mm～1240mm。本研究使用单孔板、多孔板、烧结金属板三种气体分布器类型。结合实验数据,应用最小二乘法求得各个参数值,得到的无因次传热系数关联式为St=0.179(ReFr)－0.25Pr－0.66,相关指数0.98,最大偏差18％。该关联式可应用于气－液和粒径小于100μm的气－液－固体系。     

Disjoining pressure at the edge of plane-parallel slit between solids interacting by dispersion forces

The approach to calculating the Irving-Kirkwood pressure tensor inside plane-parallel hollow slit between solids interacting by dispersion forces is developed. Disjoining pressure is defined as a normal component of pressure tensor at slit walls and is calculated as explicit function of both the width of slit and distance from its edge. It is revealed that, at preset slit width, disjoining pressure acquires its common value for an infinite slit at triple (by the width) distance from the slit edge.     

Understanding (sessile/constrained) bubble and drop oscillations

The diffuse literature on drop oscillation is reviewed, with an emphasis on capillary wave oscillations of constrained drops. Based on the review, a unifying conceptual framework is presented for drop and bubble oscillations, which considers free and constrained drops/bubbles, oscillation of the surface or the bulk (i.e. center of mass) of the drop/bubble, as well as different types of restoring forces (surface tension, gravity, electromagnetic, etc). Experimental results (both from literature and from a new set of experiments studying sessile drops in cross flowing air) are used to test mathematical models from literature, using a novel whole profile analysis technique for the new experiments. The cause of oscillation (cross flowing air, vibrated surface, etc.) is seen not to affect oscillation frequency. In terms of models, simplified models are seen to poorly predict oscillation frequencies. The most advanced literature models are found to be relatively accurate at predicting frequency. However it is seen that no existing models are reliably accurate across a wide range of contact angles, indicating the need for advanced models/empirical relations especially for drops undergoing the lowest frequency mode of oscillation (the order 1 degree 1 non-axisymmetric ‘bending’ mode that corresponds to a lateral ‘rocking’ motion of the drop).     

The low-temperature heat capacity and saturation vapor pressure of ethyl ester of butanoic acid

The heat capacity, thermodynamic properties of fusion, and purity of the ethyl ester of butanoic acid were determined by adiabatic calorimetry in the temperature range from 8 to 372 K. The pT-parameters of the ester for the equilibrium liquid-vapor were measured by comparative ebulliometry in the “atmospheric” range of pressure from 10.8 to 101.7 kPa. The obtained data were used to derive the normal boiling temperature (T _n.b), the enthalpies of vaporization at T = 298.15 K and T _n.b, and the main thermodynamic functions (changes of S, H, G) in the crystal and liquid states of the temperature interval studied and in the ideal gas state at T = 298.15 K. The experimental vapor pressures of the narrow temperature interval, ΔT = 62 K were extended to the entire range of the liquid, T _cr − T _tp⁰ = 394.3 K, from the triple, T _tp⁰, to the critical, T _cr, temperatures.     

加温加压条件下气液固三相鼓泡塔体积传质系数的测定

气液固三相鼓泡塔反应器被广泛地应用于化工、石油化工、煤化工、化工冶金、环境工程等领域,如石油馏分的加氢、煤的脱硫与脱氮、对二甲苯氧化、费托合成、甲醇合成、二甲醚合成以及含有机物废水的湿式氧化等工业过程[1.2].     

Research on the effect of bubble dynamics and turbulent kinetic energy on heat transfer in mini-channels filled with metal foam

Journal of Thermal Analysis and Calorimetry - This paper presents an investigation of the boiling heat transfer of R141b in a mini-channel with a 2.42-mm inner diameter filled with metal foam....     

液体的饱和蒸气压与内压

本文用统计热力学的方法, 建立了液体饱和蒸气压, 与内压间的关系式。对C6H6、CCl4、cy-C6H12、C(CH3)4、n-C6H14和(CH3)2CO等六种液体的检验结果表明, 上述关系式能适用于广阔的温度范围。     

Self-quenching and electronic energy transfer of triplet molecules. The benzaldehyde-biacetyl system in the vapor phase

The triplet-triplet energy transfer from benzaldehyde to biacetyl and the competing self-quenching between triplets and ground state molecules of benzaldehyde were investigated in the dilute vapor phase by monitoring the phosphorescence (T₁(nπ^*)S_o) decay of benzaldehyde. Following excitation into the S₁(nπ^*)S₀ absorption band, a triplet self-quenching rate constant of k_SQ=(2.4±0.1) × 10⁴ s^?1 Torr^?1, corresponding to a gas-kinetic cross section of σ_SQ=0.22 A², was measured. The collision-free lifetime of the benzaldehyde triplet was found to be 2.3 ± 0.4 ms. Substitution of the aldehydic proton by deuterium reduces k_SQ by a factor of two: complete deuteration of the molecule has no further effect. Under the same excitation conditions, the energy transfer rate to biacetyl is k_ET=(2.8 ± 0.1) × 10⁶ s^?1 Torr^?1, with σ_ET = 24 A². This process is not influenced by deuteration.     

Accumulating microparticles and direct-writing micropatterns using a continuous-wave laser-induced vapor bubble

Through the enhanced photothermal effect, which was achieved using a silver film, a low power weakly focused continuous-wave laser (532 nm) was applied to create a vapor bubble. A convective flow was formed around the bubble. Microparticles dispersed in water were carried by the convective flow to the vapor bubble and accumulated on the silver film. By moving the laser spot, we easily manipulated the location of the bubble, allowing us to direct-write micropatterns on the silver film with accumulated particles. The reported simple controllable accumulation method can be applied to bimolecular detection, medical diagnosis, and other related biochip techniques.