有机改性膨润土对己唑醇水悬浮体系物理稳定性的影响

利用4种季铵盐阳离子表面活性剂（十二烷基二甲基苄基氯化铵(1227)、十四烷基二甲基苄基氯化铵(1427)、十六烷基三甲基氯化铵(1631)和十八烷基三甲基氯化铵(1831)）分别对钠基膨润土（Na-Ben）进行有机改性,制得4种有机膨润土（1227-Ben、1427-Ben、1631-Ben和1831-Ben）并进行了红外光谱及X射线分析,考察了4种有机膨润土在水中的悬浮性能及对5%己唑醇水悬体系物理稳定性能的影响。 FT-IR及XRD分析结果表明,供试季铵盐阳离子的有机碳链均进入到膨润土的片层间。 水中悬浮性能测定实验表明,1831-Ben在水中悬浮性能相对较好,而其它3种均不理想,特别是1227-Ben和1427-Ben表现出强烈的斥水现象。 沉降试验表明,有机膨润土的使用有助于5%己唑醇水悬浮剂物理稳定性的提高,其中用1831-Ben制备出的水悬浮体系的物理稳定性明显优于其它3种,制剂析水率最低,屈服值与粘度最大,体系悬浮率最高,可见1831-Ben可以用作5%己唑醇水悬浮剂的抗沉降剂。     

Understanding surfactant aided aqueous dispersion of multi-walled carbon nanotubes

Dispersions of multi-walled carbon nanotubes (MWNTs) assisted by surfactant adsorption were prepared for a number of ionic and non-ionic surfactants including sodium 4-dodecylbenzenesulfonate (NaDDBS), hexadecyl(trimethyl)azanium bromide (CTAB), sodium dodecane-1-sulfonate (SDS), Pluronic? F68, Pluronic? F127, and Triton? X-100 to examine the effects of nanotube diameter, surfactant concentration, and pH on nanotube dispersability. Nanotube diameter was found to be an important role in surfactant adsorption rendering single-walled carbon nanotube studies as unreliable in predicting MWNT dispersive behavior. Similar to other reports, increasing surfactant concentrations resulted in a solubility plateau. Quantification of nanotube solubility at these plateaus demonstrated that CTAB is the best surfactant for MWNTs at neutral pH conditions. Deviations from neutral pH demonstrated negligible influence on non-ionic surfactant adsorption. In contrast, both cationic and anionic surfactants were found to be poor dispersing aids for highly acidic solutions while, CTAB remained a good surfactant under strongly basic conditions. These pH dependent results were explained in the context of nanotube surface ionization and Debye length variation.     

阴离子氨基酸表面活性剂调控碳酸钙的仿生合成

室温下, 在乙醇或乙醇-水混合体系中, 利用氨基酸表面活性剂N-酰基十二烷基肌氨酸钠(Sar)调控合成碳酸钙, 采用SEM, XRD和FTIR等技术表征了反应产物. 在乙醇体系中, 首先形成多面体形状的文石, 然后逐渐转变为圆球状的无定形碳酸钙. 在乙醇-水混合体系中, 合成了花簇状多级结构碳酸钙晶体. 增加N-酰基十二烷基肌氨酸钠的用量有助于形成球霰石结构, 当n(Ca2+)∶n(Sar)=1∶1 时, 得到的花状碳酸钙为球霰石和方解石的混合物, 当n(Ca2+)∶n(Sar)=1∶2 时, 得到纯净的球霰石, 其形貌为大小较均一的单分散的球, 直径约为7 μm; 另外, 当n(Ca2+)∶n(Sar)=1∶1时, 混合溶剂中水和乙醇的体积比由1.5∶1依次增加为7∶3和3∶1时, 碳酸钙晶体的形貌由花状逐渐向球形过渡, 晶体中球霰石和方解石的含量也随之变化, 其中, 当水和醇的体积比为7∶3时, 产物主要为球霰石型晶体.     

Formation of thin calcium carbonate films with aragonite and vaterite forms coexisting with polyacrylic acids and chitosan membranes

CaCO3 crystallization on a chitosan membrane was studied using diffusion of (NH4)2CO3 vapors into a CaCl2 solution containing differing added amounts of two polyacrylic acids (PAAs) with molecular weights of ca. 2.0 x 10(3) and ca. 4.5 x 10(4). The coexistence of PAA and the chitosan membranes produced thin CaCO3 island crystals, which developed into a continuous CaCO3 film on the membranes. Continuous CaCO3 films consisting of only aragonite formed on the chitosan membranes at the optimum amount of PAA. When the amount of PAA is not optimum, the polymorph of CaCO3 switches from aragonite to vaterite, and the morphology has a tendency to become an isolated island structure. The formation of the aragonite and vaterite island crystals and the appearance of a range of added PAA suitable for their formation are explained by the action of two parallel phenomena: (a) the high concentration of Ca2+ ions in the chitosan membrane vicinity is achieved by the interaction between the -COO- groups of PAA adsorbed by the -NH3+ groups of the chitosan membrane through an electrostatic force and free Ca2+ ions in the CaCl2 solution, which produces the high supersaturation with CaCO3 in the membrane vicinity during CO2 diffusion; (b) PAA, remaining as mobile carboxylic anions in the CaCO3 solution, inhibits the growth of the CaCO3 island crystals by its adsorption. The CaCO3 supersaturation in the membrane vicinity is controlled by regulating the balance of these phenomena, which leads to the formation of the desired CaCO3 polymorph.     

Oriented aggregation and novel phase transformation of vaterite controlled by the synergistic effect of calcium dodecyl sulfate and n-pentanol

Calcium dodecyl sulfate (CDS) was used for the first time both as an anionic surfactant and as the source of mineral ions in the precipitation process of calcium carbonate (CaCO3). The simple reaction of the enriched Ca2+ ions at the so-called organic-inorganic interfaces with the slowly bubbled CO2 gas resulted in the metastable vaterite polymorph with various structures. The single-crystalline vaterite of the hexagonal platelets, the lens-shaped structures with hexagonal symmetry, the olive-shaped superstructures and these with a concave at each top of olives, and another metastable polymorph of aragonite were obtained, respectively, depending upon the concentration ratio between CDS and n-pentanol. The synergistic effect of CDS and n-pentanol is believed to play a crucial role in driving the oriented aggregation of metastable nanoparticles. Simultaneously, the novel phase transformation of vaterite to aragonite was observed, implying the possible formation mechanism of aragonite at room temperature and in the absence of magnesium ions.     

Crystallization and aggregation behaviors of calcium carbonate in the presence of poly(vinylpyrrolidone) and sodium dodecyl sulfate

An anionic surfactant interacts strongly with a polymer molecule to form a self-assembled structure, due to the attractive force of the hydrophobic association and electrostatic repulsion. In this crystallization medium, the surfactant-stabilized inorganic particles adsorbed on the polymer chains, as well as the bridging effect of polymer molecules, controlled the aggregation behavior of colloidal particles. In this presentation, the spontaneous precipitation of calcium carbonate (CaCO3) was conducted from the aqueous systems containing a water-soluble polymer (poly(vinylpyrrolidone), PVP) and an anionic surfactant (sodium dodecyl sulfate, SDS). When the SDS concentrations were lower than the onset of interaction between PVP and SDS, the precipitated CaCO3 crystals were typically hexahedron-shaped calcite; the increasing SDS concentration caused the morphologies of CaCO3 aggregates to change from the flower-shaped calcite to hollow spherical calcite, then to solid spherical vaterite. These results indicate that the self-organized configurations of the polymer/surfactant supramolecules dominate the morphologies of CaCO3 aggregates, implying that this simple and versatile method expands the morphological investigation of the mineralization process.     

Influence of sodium dodecyl sulfate and static magnetic field on the properties of freshly precipitated calcium carbonate

Properties of calcium carbonate precipitated from aqueous solutions of CaCl(2) and Na(2)CO(3) in the presence of sodium dodecyl sulfate (SDS) and S-S 0.1 T magnetic field (MF) were studied. The nucleation and precipitation processes of CaCO(3) were investigated by pH and zeta potential measurements at 20 +/- 1 degrees C up to 2 h after mixing the solutions. Also the amounts of calcium carbonate deposited on the glass surfaces and its structure were examined. It was found that SDS influences the kinetics of precipitation, crystallographic forms, and crystal size of CaCO(3). The SDS effects are more pronounced in MF presence. A small amount of SDS accelerates transformation of vaterite into calcite, whereas increasing surfactant concentration moderates such a transformation. On the other hand, in all the systems, MF in the presence of SDS causes a slower transformation of vaterite into calcite. These effects are reflected in pH and zeta potential changes, although there is no clear dependence between the SDS amount present during the precipitation and changes of the parameters investigated. It seems that MF effect is most significant at a defined optimal SDS concentration. The results, however, do not allow suggestion of any detailed mechanism of the field interaction.     

Formation of stable vaterite with poly(acrylic acid) by the delayed addition method

The crystallization of CaCO3 was examined by changing the addition time of poly(acrylic acid) (PAA) to an aqueous solution of calcium carbonate by selectively interacting with the crystal at different stages during the crystal-forming process. The precipitation of CaCO3 was carried out by a double jet method to prevent heterogeneous nucleation on glass walls, and the sodium salt of PAA was added by a delayed addition method. In the initial presence of PAA in an aqueous solution of calcium carbonate, PAA acted as an inhibitor for the nucleation and growth of crystallization. However, it was found that stable vaterite particles were successfully obtained by delaying the addition of PAA from 1 to 60 min. The vaterite particles were stable in the aqueous solution for more than 30 days, and the CaCO3 particles were formed by a spherulitic growth mechanism. It is suggested that PAA strongly binds with the Ca2+ ion on the surface of CaCO3 particles to stabilize the unstable vaterite form effectively. Upon changing the addition time of PAA, we found that CaCO3 particles were formed through different formation mechanisms in selectively controlled crystallization at different stages during the crystallization process.     

1H NMR relaxation of water: a probe for surfactant adsorption on kaolin

In this study, (1)H NMR is used to investigate properties of sodium dodecyl sulfate (SDS), tetradecyl trimethyl ammonium bromide (TTAB), and dodecyl trimethyl ammonium bromide (DTAB) adsorbed on kaolin by NMR T(1) and T(2) measurements of the water proton resonance. The results show that adsorbed surfactants form a barrier between sample water and the paramagnetic species present on the clay surface, thus significantly increasing the proton T(1) values of water. This effect is attributed to the amount of adsorbed surfactants and the arrangement of the surfactant aggregates. The total surface area covered by the cationic (DTAB and TTAB) and anionic (SDS) surfactants could be estimated from the water T(1) data and found to correspond to the fractions of negatively and positively charged surface area, respectively. For selected samples, the amount of paramagnetic species on the clay surface was reduced by treatment with hydrofluoric (HF) acid. For these samples, T(1) and T(2) measurements were taken in the temperature range 278-338 K, revealing detailed information on molecular mobility and nuclear exchange for the sample water that is related to surfactant behavior both on the surface and in the aqueous phase.     

Effect of Surfactants and Ionic Strength on Dissociation of Hydrochlorides of Phenothiazine Derivatives

Abstract

A study of the effect of the anionic surfactant dodecyl sulfate, the cationic surfactant carbethoxypentadecyl trimethyl ammonium bromide (Septonex), nonionic surfactant p-octyl phenyl polyoxyethylene (Triton X-100), and a strong electrolyte (KBr) on the dissociation of the hydrochlorides of two derivatives of phenothiazine (diethazine and fluphenazine) was made. It was found that sodium dodecyl sulfate increases the pKa value, whereas Septonex and Triton X-100 decrease this value. The presence of KBr suppresses the effect of the surfactants. A new method for the potentiometric determination of fluphenazine in an aqueous medium was proposed.     

二元阴阳离子表面活性剂法合成介孔氧化硅囊泡

以十二烷基磺酸钠(SDS)和十六烷基三甲基溴化铵(CTAB)为表面活性剂, 在SDS与CTAB的摩尔比为1.0~2.3时, 以正硅酸乙酯(TEOS)为硅源, 在氨水-水体系中于68℃下合成介孔氧化硅囊泡. 通过透射电子显微镜(TEM)、 X射线衍射仪(XRD)、 热重分析仪(TGA)和氮气吸附-脱附实验仪对合成的产物进行表征. 结果表明, 合成的产物为介孔氧化硅囊泡聚集体, 孔径约为4 nm, 样品的Brunauer-Emmett-Teller(BET)比表面积为826 m²/g. 对介孔氧化硅囊泡的形成机理做了初步探讨.     

改性硝酸铵自敏化结构特征

对经复合表面活性剂处理的改性硝酸铵及普通硝酸铵晶体进行电镜扫描,孔径孔容分布,粒径分布,比表面积测定,抗吸湿结块性,差示量热分析以及爆炸性能的实验研究,结果表明,与普通硝酸铵相比,改性硝酸铵的晶形歧化,比表面积大,富含气孔,大部分的有效孔径座落在介孔范围,有较好的粒度级配,晶变热降低,且晶变点后移,具备自敏化结构特征,并且有良好的抗吸湿结块性,用它代替普通硝酸铵所制得的粉状工业炸药具有良好的物理性能和爆炸性能。     

Interactions in solution between a hydrophobic polymer and various kinds of surfactants

Interactions in solution between a hydrophobic polymer and surfactants were studied by viscometry, light scattering and conductimetry measurements. One polymer, poly(2-ethyl hexyl methacrylate) (P2EHMA), five surfactants, sodium dodecyl sulfate (SDS), hexadecyl trimethylammonium bromide (HTAB), hexadecyl pyridinium chloride (HPCl), and ethoxylated nonyl phenol containing 10 or 25 segments of ethylene oxide (NP10 or NP25), and one solvent mixture, THF/6 vol% H₂O were used in this work. For the P2EHMA/surfactant mixtures in THF/6 vol% H₂O, the viscosity versus surfactant concentration curves are similar in shape for all surfactants. They show a minimum at low surfactant concentration followed at higher concentration by a maximum and a plateau. An interpretation of these curve shapes is proposed. The relevance of these findings to the problem of the polymer/surfactant interactions in latexes and latex films is also discussed.     

碳酸钙在聚合物胶束控制下的仿生合成

合成了温敏性的聚(N-异丙基丙烯酰胺)-b-聚(L-谷氨酸)(PNIPAM-b-PLGA)嵌段共聚物,在较高温度下制备了以PNIPAM为核、以PLGA为壳的自组装胶束,研究了胶束对碳酸钙晶体生长的控制作用.使用扫描电镜和X射线衍射表征了碳酸钙晶体的形貌和晶型.当聚合物胶束浓度较高时,得到纤维状的文石;当胶束浓度较低时,...     

Influence of surfactants on the morphologies of CaCO3 by carbonation route with compressed CO2

Three surfactants, sodium dodecyl sulfate (SDS), cetyltrimethylammonium bromide (CTAB) and polyoxyethylene-80-sorbitan monooleate (Tween 80), were used to control the growth of CaCO₃ crystals by carbonation route using Ca(OH)₂ and compressed CO₂. The obtained CaCO₃ particles were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD) techniques. The effects of surfactants on the morphology of the particles were studied. It was demonstrated that Tween 80 and SDS have obvious effect on the morphology of CaCO₃ particles, while CTAB does not affect morphology considerably. The possible mechanism has been discussed on the basis of the binding of the surfactants to the certain face of the crystals.     

Photochemistry of Flavins in Micelles: Specific Effects of Anionic Surfactants on the Monomerization of Thymine Cyclobutane Dimers Photosensitized by Tetra-O-acyl Riboflavins*

It was found that tetra-o-acyl riboflavins efficiently photosensitize the monomerization of the cis, syn-cyclobutane dimers of 1,3-dimethylthymine and 1,3-dimethyluracil in aqueous solution in the presence of such anionic surfactants as sodium dodecyl sulfate and sodium hexadecyl sulfate at concentrations higher than their critical micelle concentration, while little monomerization of the dimers was photosensitized by the flavins in the absence of the surfactants and even in the presence of cationic and nonionic surfactants.     

The modification of the triple helical structure of gelatin in aqueous solution 3. The influence of cationic surfactants

The interaction between cationic surfactants (hexadecyl and dodecyl trimethyl ammonium bromide) and gelatin was characterized by measuring the circular dichroism. The interaction between the cationic surfactants and gelatin is weak in comparison to that of anionic surfactants. When the concentration of cationic surfactants is sufficiently low, refolding of the gelatin-strands to the triple helical structure by rechilling the solution from 298 K to 283 K is complete. The triple helical content of the solution is affected more strongly by the cationic surfactants in acidic solution than at pHs 7 or 10. The interaction depends on the apolar group of the surfactant and is found to be stronger for DTAB than for CTAB at 298 K. Coagulation of the hydrophobic gelatin-cationic surfactant complexes does not comprise that pan of gelatin which is able to refold the triple helical structure. Therefore, the gelatin-strands of lower molecular weights are thought to react favorably with the surfactant ions.     

Effect of surfactant structure on catalysis of microemulsion for photoisomerization of trans-stilbene

In this study,the photoisomerization of trans-sfilbene was carried out in water in oil (W/O) microemulsions by using sodium dodecyl sulfate (SDS),dodecyl trimethyl ammonium bromide (DTAB) and cetyl trimethyl ammonium bromide (CTAB) as surfactant,respectively.The catalytic effect of microemulsion on this reaction is closely related to the structure of surfactant.When there is no photosensitizer 9,10-dicyanoanthracene (DCA),the surfactant with shorter hydrophobic chain is preferred,while in the presence of DCA,the surfactant with anionic polar group is preferred.     

Suppression of surfactant interferences in anodic stripping voltammetry by sodium dodecyl sulfate

It was investigated whether interferences from surfactants in anodic stripping voltammetry (ASV) could be remedied by the anionic surfactant sodium dodecyl sulfate (SDS) which causes little or no interference in itself. Cadmium and lead were used as test analytes, and measurements were performed in acetate buffer as well as in 0.1 M HNO₃. One hundred parts per million of the interfering surfactant was added. SDS eliminated severe interference from the non-ionic surfactants Triton^© X-100 and dodecyl octaethylene glycol ether as well as from the polymer polyethylene glycol 6000 and from the cationic surfactant cetyl trimethyl ammonium bromide. SDS could not remedy the extraordinarily severe interference from the cationic surfactant cetyl pyridinium chloride. Two anionic surfactants were also tested as interferents but they had little detrimental effect on the ASV signals. The effect of SDS was explained by the formation of mixed micelles which scavenge the interferent in the bulk solution and by competitive displacement of the interferent at the electrode surface.     

Adsorption of methylene blue and orange II onto unmodified and surfactant-modified zeolite

Adsorption of cationic methylene blue and anionic orange II onto unmodified and surfactant-modified zeolites was studied using a batch equilibration method. The effects of equilibrium time, solution pH, and sorption temperature were examined. The results suggested that 2% sodium dodecyl benzenesulfonate (SDBS)- and 3% sodium dodecyl sulfate (SDS)-modified zeolites had higher adsorption capacities for methylene blue than the unmodified zeolite, while 2% cetylpyridinium bromide hexadecyl (CPB)- and 2% hexadecylammonium bromide (HDTMA)-modified zeolites were the best adsorbents for orange II. The adsorption conditions were optimized, and the mechanisms of adsorption are briefly discussed.