On electrochemistry of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-coated LiCoO<Subscript>2</Subscript> composite cathode with improved cycle stability

LiCoO₂-based cathode does still have a powerful competition in high-end mobile electronics due to its relatively high true density (about 5.2 g/cm³). When the operation potential range is extended, the improvement in its cycle stability has attracted more attention. The extension of its operation potential can be realized by partial replacement of Co by Ni and Mn or by surface modification. However, Ni and Mn replacing partial Co results in decreased true density; for example, the true density of LiNi_0.5Mn_0.3Co_0.2O₂ is about 4.6 g/cm³. In this case, the increase in its practical energy density is impossible. As a result, the surface modification technology becomes very important to extend its operation potential range. In this article, an Al₂O₃-coated LiCoO₂ cathode was synthesized. X-ray diffraction test did not show any impurity. Scanning electron spectroscopy measurements showed that the basic microstructure of pristine LiCoO₂ grain is sustained after coating Al₂O₃. The surface characteristic of pure and Al₂O₃-coated LiCoO₂ was also analyzed using an X-ray photoelectron spectroscopy (XPS) technique. Unusual XPS peaks of O 1s, Al 2p, and Co 2p binding energy were found and may be caused by the possible H existence in crystal structure. The electrochemical behavior was systematically investigated, and the cathode was cycled at different charge cutoff voltages (4.30～4.60 V). The charge-discharge and cyclic voltammetry measurements showed an obviously improved cyclic performance after coating Al₂O₃. The electrocatalytic activity is not clearly changed before and after coating Al₂O₃. From our systematical investigation, it could be concluded that the Al₂O₃-coated LiCoO₂ cathode is suitable for practical application in the potential range of 3.70～4.50 V vs. Li/Li⁺.     

One-step solid-state synthesis of nanosized LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cathode material with power properties

A simple one-step solid state reaction way of preparing nanosized LiMn₂O₄ powders with high-rate properties is investigated. Oxalic acid is used as a functional material to lose volatile gases during the process of calcining in order to control the morphology and change the particle size of materials. The results of X-ray diffraction and scanning electron microscopy show that particle size of materials decreases with the increase of the oxalic acid content. The electrochemical test results indicate that optimal LiMn₂O₄ particles (S_0.5) is synthesized when the molar ratios of oxalic acid and total Mn source are 0.5:1. It also manifests that LiMn₂O₄ sample with middle size has the optimal electrochemical performance among five samples instead of the smallest LiMn₂O₄ sample. The obtained sample S_0.5 with middle size exhibits a high initial discharge capacity of 125.8 mAh g^?1 at 0.2C and 91.4% capacity retention over 100 cycles at 0.5C, superior to any one of other samples. In addition, when cycling at the high rate of 10C, the optimal S_0.5 in this work could still reach a discharge capacity of 80.8 mAh g^?1. This observation can be addressed to the fact that the middle size particles balance the contradictory of diffusion length in solid phase and particle agglomeration, which leads to perfect contacts with the conductive additive, considerable apparent Li-ion diffusion rate, and the optimal performance of S_0.5.     

Study of structural phase transitions in YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>6+δ</Subscript> by x-ray photoelectron spectroscopy

We have used x-ray photoelectron spectroscopy to investigate the charge state of oxygen found in the basal structural plane of YBa₂Cu₃O₆+γ.. We have observed a change in this state after thermal treatment, with a transition to the adjacent structural phase region. We have shown that changes in the charge state of oxygen can be used as an indicator of structural changes occurring in YBa₂Cu₃O₆+δ.. We have found that the rate of structural relaxation yttrium barium cuprate depends on the amount of structural water it contains. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 2, pp. 195–198, March–April, 2007.     

Pseudo-capacitive properties of LiCoO<Subscript>2</Subscript>/AC electrochemical capacitor in various aqueous electrolytes

LiCoO₂ particles were synthesized by a sol-gel process. X-ray diffraction analysis reveals that the prepared sample is a single phase with layered structure. A hybrid electrochemical capacitor was fabricated with LiCoO₂ as a positive electrode and activated carbon (AC) as a negative electrode in various aqueous electrolytes. Pseudo-capacitive properties of the LiCoO₂/AC electrochemical capacitor were determined by cyclic voltammetry, charge–discharge test, and electrochemical impedance measurement. The charge storage mechanism of the LiCoO₂-positive electrode in aqueous electrolyte was discussed, too. The results showed that the potential range, scan rate, species of aqueous electrolyte, and current density had great effect on capacitive properties of the hybrid capacitor. In the potential range of 0–1.4 V, it delivered a discharge specific capacitance of 45.9 Fg^–1 (based on the active mass of the two electrodes) at a current density of 100 mAg^–1 in 1 molL^–1 Li₂SO₄ aqueous electrolyte. The specific capacitance remained 41.7 Fg^–1 after 600 cycles.     

Metastable superconductivity of the Al/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> interface

Superconductivity in the interface region between metallic Al and its oxide, Al₂O₃, has been detected at about 45 K in the measured dynamic magnetic susceptibility.     

Impedance spectroscopy study of Na<Subscript>1/2</Subscript>Sm<Subscript>1/2</Subscript>TiO<Subscript>3</Subscript> ceramic

Complex impedance analysis of a valence-compensated perovskite ceramic oxide Na_1/2Sm_1/2TiO₃, prepared by a mixed oxide (solid-state reaction) method, has been carried out. The formation of single-phase material was confirmed by X-ray diffraction studies, and it was found to be an orthorhombic phase at room temperature. In a scanning electron microscope, grains separated by well-defined boundaries are visible, which is in good agreement with that of impedance analysis. Alternating current impedance measurements were made over a wide temperature range (31–400 °C) in an air atmosphere. Complex impedance and modulus plots helped to separate out the contributions of grain and grain boundaries to the overall polarization or electrical behavior. The physical structure of the samples was visualized most prominently at higher temperatures (275 °C) from the Nyquist plots showing inter- and intragranular impedance present in the material. The frequency dependence of electrical data is also analyzed in the framework of the conductivity and modulus formalisms. The bulk resistance, evaluated from the impedance spectrum, was observed to decrease with rise in temperature, showing a typical negative temperature coefficient of resistance-type behavior like that of semiconductors. The modulus mechanism indicates the non-Debye type of conductivity relaxation in the materials, which is supported by the impedance data. PACS 77.22.Ch; 77.22.Ej; 77.22.Gm; 77.22.Jp; 77.84.Bw     

Properties of an Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/Si interface

The phase chemical composition of an Al₂O₃/Si interface formed upon molecular deposition of a 100-nm-thick Al₂O₃ layer on the Si(100) (c-Si) surface is investigated by depth-resolved ultrasoft x-ray emission spectroscopy. Analysis is performed using Al and Si L_{2, 3} emission bands. It is found that the thickness of the interface separating the c-Si substrate and the Al₂O₃ layer is approximately equal to 60 nm and the interface has a complex structure. The upper layer of the interface contains Al₂O₃ molecules and Al atoms, whose coordination is characteristic of metallic aluminum (most likely, these atoms form sufficiently large-sized Al clusters). The shape of the Si bands indicates that the interface layer (no more than 10-nm thick) adjacent to the substrate involves Si atoms in an unusual chemical state. This state is not typical of amorphous Si, c-Si, SiO₂, or SiO_x (it is assumed that these Si atoms form small-sized Si clusters). It is revealed that SiO₂ is contained in the vicinity of the substrate. The properties of thicker coatings are similar to those of the 100-nm-thick Al₂O₃ layer and differ significantly from the properties of the interfaces of Al₂O₃ thin layers.     

Investigation of Cu<Subscript>0.5</Subscript>Ni<Subscript>0.5</Subscript>/Nb interface transparency by using current-perpendicular-to-plane measurement

A direct determination of the interfacial transparency on the basis of current-perpendicular-to-plane (CPP) resistances for Cu_0.5Ni_0.5/Nb layered system is presented. This particular realization has substantial significance for understanding the interfacial transport in such heterostructures. The unexpected large critical thickness for this weak ferromagnetic containing system can be attributed to the strong pair-breaking effect as a result of the high interfacial transparency. Besides, the strong pair-breaking also plays a decisive role in the occurrence of the dimensionality crossover of the temperature dependent upper critical magnetic field.     

Dual-functional materials for interface modifications in solid-state dye-sensitised TiO<Subscript>2</Subscript> solar cells

The concept of solid-state dye-sensitised TiO₂ solar cells with an organic semiconductor as hole-transport medium is studied in detail by examining the dye–hole conductor interface. The facile transfer of holes from Ru-dye core to the hole conductor requires suitable interface modifiers which have the function of dye and hole transport moiety, but with exactly positioned anchor groups and antenna functions. The synthesis and characterisation of such novel low molecular weight multifunctional molecules carrying dye units and triphenylamine moieties are presented and their influence as interface modifiers is studied. This interface modification results in doubling the external quantum efficiency of current conversion via improved charge transfer at the dye–hole conductor interface. Moreover, the recombination processes at this interface are drastically suppressed, which leads to higher open-circuit voltage and consequently higher power-conversion efficiency. The concept is also extended to polymers to obtain dye-centred polymeric hole conductors which carry a single Ru-dye unit in the middle of the poly(vinyltriphenylamine) chain that acts as hole-conductor polymer. The polymerisation was carried out by atom-transfer radical polymerisation of 4-bromostyrene followed by polymer amination and finally metallation with Ru-bis(bipyridyl) precursors . PACS 81.07.Bc; 81.05.Lg; 81.16.Dn; 81.20.Fw; 84.60.Jt     

Synthesis and characterization of electron beam evaporated LiCoO<Subscript>2</Subscript> thin films

LiCoO₂ thin films were prepared by electron beam evaporation technique using LiCoO₂ target with Li/Co ratio 1.1 in an oxygen partial pressure of 5 × 10⁻⁴ mbar. The films prepared at substrate temperature T _s < 573 K were amorphous in nature, and the films prepared at T _s > 573 K exhibited well defined (104), (101), and (003) peaks among which the (104) orientation predominates. The X-ray photoelectron spectroscopy (XPS) and inductively coupled plasma (ICP) data revealed that the films prepared in the substrate temperature range 673–773 K are nearly stoichiometric. The grain size increases with an increase of substrate temperature. The Co–e_g absorption bands, are empty and their peak position lies at around 1.7 eV above the top to the Co–t_2g bands. The fundamental absorption edge was observed at 2.32 eV. The films annealed at 1,023 K in a controlled oxygen environment exhibit (104) out plane texture with large grains. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006     

Enhanced electrochemical performance of lithium ion battery cathode Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C

Li-ion battery cathode material lithium-vanadium-phosphate Li₃V₂(PO₄)₃ was synthesized by a carbon-thermal reduction method, using stearic acid, LiH₂PO₄, and V₂O₅ as raw materials. And stearic acid acted as reductant, carbon source, and surface active agent. The effect of its content on the crystal structure and electrochemical performance of Li₃V₂(PO₄)₃/C were characterized by XRD and electrochemical performance testing, respectively. The results showed that the content of carbon source has no significant effect on the crystal structure of lithium vanadium phosphate. Lihtium vanadium phosphate obtained with 12.3% stearic acid demonstrated the best electrochemical properties with a typical discharge capacity of 119.4 mAh/g at 0.1 C and capacity retention behavior of 98.5% after 50 cycles. And it has high reversible discharge capacity of 83 mAh/g at 5 C with the voltage window of 3 to 4.3 V.     

Impedance spectroscopy study of Pb<Subscript>2</Subscript>P<Subscript>2</Subscript>O<Subscript>7</Subscript> compound

The lead pyrophosphate, Pb₂P₂O₇, compound was prepared by conventional solid-state reaction and identified by X-ray powder diffractometer. Pb₂P₂O₇ has a triclinic structure whose electrical properties were studied using impedance spectroscopy technique. Both impedance and modulus analysis exhibit the grain and grain boundary contribution to the electrical response of the sample. The temperature dependence of the bulk and grain boundary conductivity were found to obey the Arrhenius law with activation energies E _g = 0.66 eV and E _gb = 0.67 eV, respectively. The scaling behavior of the imaginary part of the complex impedance suggests that the relaxation describes the same mechanism at various temperatures.     

Dielectric spectroscopy study of the new compound [C<Subscript>12</Subscript>H<Subscript>17</Subscript>N<Subscript>2</Subscript>]<Subscript>2</Subscript>CdCl<Subscript>4</Subscript>

The temperature dependence of the electrical conductivity of the compound 2,4,4-trimethyl-4,5-dihydro-3H-benzo[b] [1,4] diazepin-1-ium tetrachlorocadmiate in the different phases follows the Arrhenius law. The imaginary part of the permittivity constant is analyzed with the Cole–Cole formalism. In the temperature range 348–394 K, the activation energy of conductivity obtained from complex permittivity in regions I and II are, respectively, 1.03 and 0.33 eV, and E _m (in regions I and II are, respectively, 0.97 and 0.36 eV) obtained from the modulus spectra is close, suggesting that the ion transport is probably due to a hopping mechanism. The Kohlrausch–Williams–Watts function, j(t) = exp( - ( \fractt_\textKWW )^b ) \varphi (t) = \exp \left( { - {{\left( {\frac{t}{{{\tau_{\text{KWW}}}}}} \right)}^\beta }} \right) , and the coupling model are utilized for analyzing electric modulus at various temperatures. The decreasing of β at 373 K is due to approaching the temperatures of change in the conduction mechanism of the sample.     

Enhanced electrochemical performances of Li<Subscript>2</Subscript>MnO<Subscript>3</Subscript> cathode materials by Al doping

Al-doped Li₂MnO₃ (Li₂Mn_0.9Al_0.1O₃) lithium-rich layered oxide is prepared and investigated as cathode material for lithium-ion batteries (LIBs). X-ray diffraction (XRD) and scanning electron microscopy-energy dispersive spectrometer (SEM-EDS) analyses reveal that the Al element is distributed in the sample homogenously. The Al-LMO sample exhibits a great improvement on the rate capability and cycling stability compared to the LMO sample. The differential capacity versus voltage (dQ/dV) results reveal that Al doping would be to prevent the first charge phase transformation from a layered phase to a cubic spinel-like phase and also slowdown the rate of transformation upon cycling. Electrochemical impedance spectroscopy (EIS) results confirm that Al doping decreases the charge-transfer resistance and improves the electrochemical reaction kinetics.     

Investigation on structural characteristics of PVDF–AgCF<Subscript>3</Subscript>SO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocomposite solid polymer electrolyte system

There has been an increasing interest towards the incorporation of nanosize ceramic fillers in polymer electrolytes. Solid polymer electrolytes based on polyvinylidene fluoride (PVDF), silver triflate (AgCF₃SO₃), and x wt% of aluminum oxide (Al₂O₃) nanopowders (where x = 1, 3, 5, and 10, respectively) have been prepared using solution casting technique. The structural characteristics of these thin film specimens were studied using Fourier transform infrared (FTIR) and X-ray diffraction (XRD) patterns at room temperature. The appearance of new absorption bands and gradual shifts observed in some characteristic peaks confirmed the complex formation between polyvinylidene fluoride and silver triflate. Furthermore, the addition of nanosized filler Al₂O₃ has also indicated the interaction of the filler with the polymer salt complex. The XRD patterns obtained for all these samples in the 2θ range 10° to 70° showed the amorphous nature of these samples. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, December 7–9, 2006.     

Impedance spectroscopy of vanadium modified BaBi<Subscript>2</Subscript>Nb<Subscript>2</Subscript>O<Subscript>9</Subscript> ceramics

In recent years a wide range of Aurivillius layered materials have been introduced. These novel materials are produced in many various forms such as fibers, thin films as well as bulk by using a number of processing routes. As advanced materials they are they have many interesting properties which include a number of useful electrical properties related to separated grain and grain boundary conductivity, impedance, activation energies, etc. In this paper these properties are described and discussed in detail. The electrical properties of the vanadium doped BaBi₂Nb₂O₉ ceramic was measured over a wide range of temperatures by impedance spectroscopy (IS). The separated grain activation energy, calculated from Arrhenius characteristics at temperatures between room temperature and 600 °C, was 1 eV for 0 at.% of vanadium dopant and 1.2 eV for 10 at.%, whereas the activation energies in the grain boundary region were 0.97 and 1.15 eV, respectively. The obtained results suggest the significant role of vanadium dopant, causing ordering the crystalline structure.     

Photoacoustic spectroscopy of thin films of As<Subscript>2</Subscript>S<Subscript>3</Subscript>, As<Subscript>2</Subscript>Se<Subscript>3</Subscript> and GeSe<Subscript>2</Subscript>

Photoacoustic spectroscopy (PAS) is one of the important branches of spectroscopy, which enables one to detect light-induced heat production following the absorption of pulsed radiation by the sample. As₂S₃, As₂Se₃ and GeSe₂ exhibit a wide variety of photo-induced phenomena that enable them to be used as optical imaging or storage medium and various electronic devices, including electro-optic information storage devices and optical mass memories. Therefore, accurate measurement of thermal properties of semiconducting films is necessary to study the memory density. The thermal conductivity of thin films of As₂S₃ (thickness 100 μm and 80 μm), As₂Se₃ (thickness 100 μm and 80 μm) and GeSe₂ (thickness 120 μm and 100 μm) has been measured using PAS technique. Our result shows that the thermal conductivity of thicker films is larger than the thinner films. This can be explained by the thermal resistance effect between the film and the surface of the substrate.      

Synthesis of LiCoO<Subscript>2</Subscript> via sol-gel method for aqueous rechargeable lithium batteries

A crystalline structure of LiCoO₂ sample was synthesized at different stirring times via sol-gel method. This was followed by the electrochemical characterization of LiCoO₂ in 5 M LiNO₃ aqueous electrolyte. The hexagonal LiCoO₂ was stirred for 30 h produced the highest peak intensity and smallest particle size. A morphological analysis showed the particle size distribution within the range of 0.32–0.47 μm. At lower scan rates of cyclic voltammetry, three pairs of redox peaks at E_SCE = 0.81/0.65, 0.89/0.83 and 1.01/0.95 V were observed. The peak separation was proportionally consistent with Li⁺ diffusion coefficients of 7.42 × 10^?8 cm² s^?1 (anodic) and 3.59 × 10^?8 cm² s^?1 (cathodic). For specific capacity, the LiCoO₂ demonstrated a higher initial specific capacity (115.49 mA h g^?1). A small difference (1.92 Ω) in the charge transfer resistance before and after a charge discharge analysis indicated that the Li⁺ ions had been well-diffused during the intercalation/de-intercalation process.     

Impedance spectroscopy analysis of Li<Subscript>2</Subscript>SnO<Subscript>3</Subscript>

In this work, Li₂SnO₃ has been synthesized by the sol–gel method using acetates of lithium and tin. Thermogravimetric analysis (TGA) has been applied to the precursor of Li₂SnO₃ to determine the suitable calcination temperature. The formation of the compound calcined at 800 °C for 9 h has been confirmed by X-ray diffraction (XRD) analysis. The Li₂SnO₃ is then pelletized and electrically characterized by using electrochemical impedance spectroscopy (EIS) in the frequency range from 50 Hz to 1 MHz. The complex impedance spectra clearly show the dominating presence of the grain boundary effect on electrical properties whereas the complex modulus plots reveal two semicircles which are due to the grain (bulk) and grain boundary. The spectra of imaginary parts of both impedance and modulus versus frequency show the existence of peaks with the modulus plots exhibiting two peaks that are ascribed to the grain and grain boundary of the material. The peak maximum shifts to higher frequency with an increase in temperature and the broad nature of the peaks indicates the non-Debye nature of Li₂SnO₃. The activation energy associated with the dielectric relaxation obtained from the electrical impedance spectra is 0.67 eV. From the electric modulus spectra, the activation energies related to conductivity relaxation in the grain and grain boundary of Li₂SnO₃ are 0.59 and 0.69 eV, respectively. The conductivity–temperature relationship is thermally assisted and obeys the Arrhenius rule with the activation energy of 0.66 eV. The conduction mechanism of Li₂SnO₃ is via hopping.     

Electrochemical properties of Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>/C cathode materials synthesized via ethylene glycol-assisted solvothermal method

The Li₃V₂(PO₄)₃/C (LVP/C) cathode materials for lithium-ion batteries were synthesized via ethylene glycol-assisted solvothermal method. The phase composition, phase transition temperature, morphology, and fined microstructure were studied using X-ray diffraction (XRD), differential thermal analyzer (DTA), scanning electron microscope (SEM), and transmission electron microscope (TEM), respectively. The electrochemical properties, impedance, and electrical conductivity of LVP/C cathode materials were tested by channel battery analyzer, the electrochemical workstation, and the Hall test system, respectively. The results shown that the appropriate amount of water added to ethylene glycol solvent contributes to the synthesis of pure phase LVP. The LVP₁₀/C cathode material can exhibit discharge capacities of 128, 126, 126, 123, 124, and 114 mAh g^?1 at 0.1, 0.5, 2, 5, 10, and 20 C in the voltage range of 3.0–4.3 V, respectively. Meanwhile, it shows also a stable cycling performance with the capacity retention of 89.6% after 180 cycles at 20 C.