IR—ATR法研究聚对苯二甲酸乙二酯三维卷曲中空纤维的取向

应用红外衰减全反射法考察了聚对苯二甲酸乙二酯三维卷曲中空纤维在加工过程中的结构和取向的变化。结果表明，此种ＰＥＴ中空纤维中，其羰基倾向生趣于纤维表面的取向。     

CRYSTALLIZATION IN PARTIALLY MOLTEN ORIENTED BLENDS OF POLYCONDENSATES AS REVEALED BY X-RAY STUDIES*

Oriented fibers or films of binary polymer blends from polycondensates were investigated by two-dimensional (2D) wide-angle X-ray scattering (WAXS) during the finishing process of microfibrillar reinforced composite (MFC) preparation, that is, heating to a temperature between the melting temperatures of the two components, isothermal annealing, and subsequent cooling. It is shown that the crystallization behavior in such MFC from polycondensates depends not only on the blend composition, but also on thermal treatment conditions. Poly(ethylene terephthalate)/polyamide 12 (PET/PA12), poly(butylene terephthalate)/poly(ether ester) (PBT/PEE), and PET/PA6 (polyamide 6) composites were prepared in various compositions from the components. Materials were investigated using rotating anode and synchrotron X-ray source facilities. The effect of the annealing time on the expected isotropization of the lower melting component was studied in the PET/PA6 blend. It was found that PA6 isotropization took place after 2 h; shorter (up to 30 min) and longer (up to 8 h) melt annealing results in oriented crystallization due to different reasons. In PET/PA12 composites, the effect of PA12 transcrystallization with reorientation was confirmed for various blend compositions. The relative strength of the effect decreases with progressing bulk crystallization. Earlier presumed coexistence of isotropic and highly oriented crystallites of the same kind with drawn PBT/PEE blend was confirmed by WAXS from a synchrotron source.

     

Molecular dynamics simulation study on the structural properties of poly (ethylene terephthalate) under uniaxial extension and thermal shrinkage processes

In thermal shrinkage process for polyethylene terephthalate (PET) films, PET film is uniaxially stretched and then thermally relaxed. We investigate the effect of heat relaxation temperature on the thermal shrinkage of uniaxially stretched PET film using molecular dynamics simulation method. Through our investigation, we find that the thermal shrinkage ratio of the amorphous PET film is reduced as a function of heat relaxation temperature, whereas the skirt ratio is weakly correlated with the heat relaxation temperature, exhibiting the most negative skirt ratio in the case of the highest thermal shrinkage ratio. Our analysis on the PET film at molecular level further verifies that the trans-gauche transformation observed in ethylene glycol units during the simulated process is a driving force for the thermal shrinkage of uniaxially stretched PET systems.     

Polypropylene/Poly (Trimethylene Terephthalate)–Blend Fibers

Polypropylene (PP)/polyester (PES)–blend fibers were prepared by extruder melt spinning. The polymer blend consisted of PP and a “master batch” (MB) based on polytrimethylene terephthalate (PTT) or polyethylene terephthalate (PET), binary PTT/PET or PP/PTT blends, and also on a ternary PP/(PTT/PET) blend. The phase structure of PP/PES–blend fibers was examined. PES microfibers showed separation from the PP matrix in blend fibers. The impact of MB composition and rheological characteristics on phase structure parameters indicate a significant contribution of the PTT in the binary MB on the length of dispersed PES microfibers in the PP matrix. However, the blends of PP and ternary MB (PP/PTT/PET) have a lower diameter and length of the PES microfibers. The presence of PTT/PET (PES) enhances the structural and mechanical properties of the blend PP/PES fibers. In addition, PTT increases the tensile strength of the PP/PES–blend fibers if a binary MB is used, while the fiber nonuniformity is reduced in the presence of a ternary MB.     

Crystallization Behavior and Crystal Morphology of PTT/PBT Blends

The crystallization behavior and crystal morphology of the poly(trimethyl terephthalate) (PTT)/poly(butylene terephthalate) (PBT) blends were investigated by means of differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD) and polarized light microscopy (PLM) techniques. It was found that the two components crystallized simultaneously in the crystalline regions. The degree of crystallinity changed with PTT content. Crystalline properties were worse when the ratio of PBT and PTT contents was close to 50:50, but were better when PBT content was greatly different from PTT content.     

Effect of Organoclay Platelets on Crystallization of Polytrimethylene Terephthalate/Polyethylene-octene-g-maleic Anhydride Blends: Isothermal Crystallization

The blends of poly(trimethylene terephthalate) (PTT) with maleic anhydride-grafted poly(ethylene-octene) (POE-g-MA) and organoclay (OMMT) were prepared by melt-blending. The effects of organoclay platelets on the isothermal crystallization behaviors of PTT/POE-g-MA blend were examined using differential scanning calorimetry. The crystallization kinetics of the primary stage under isothermal conditions could be described by the Avrami equation, with values of the Avrami exponent between 2.01 and 2.81 for all samples. The crystallization rate parameter, K, decreased with increase of melt-crystallization temperature for all samples. The activation energies for isothermal crystallization were determined by the Arrhenius equation.     

Toughened Poly(Trimethylene Terephthalate) by Blending with a Functionalized Metallocenic Poly(Ethylene-Octene) Copolymer

New toughened poly(trimethylene terephthalate) (PTT) materials were obtained by melt blending with maleic anhydride grafted poly(ethylene-octene) (POEg). Rheological properties, mechanical properties, and morphological characteristics of PTT/POEg blends at four different compositions—95/5, 90/10, 80/20, and 70/30—were studied. The melt viscosity of the blends shows a linear decrease on increasing the POEg content. The addition of rubbery POEg to the PTT matrix increases the impact strength, while tensile properties decrease. Scanning electron microscopy (SEM) displayed a very good dispersion of POEg particles in the PTT matrix. Differential scanning colorimetry (DSC) experiments showed that for all samples the melting point was almost constant and the crystallinity did not show obvious differences. SEM results showed shear yielding of the PTT matrix was the major toughening mechanism.     

The Composition,Sequence Analysis,and Crystallization Characterization of Poly(Trimethylene‐co‐Butylene Terephthalate) Copolymer

A series of poly(trimethylene‐co‐butylene terephthalate) (PTBT) copolymers were prepared by direct esterification followed by polycondensation. The composition and sequence distribution of the copolymers were investigated by nuclear magnetic resonance (NMR). The results demonstrate that the synthesized PTBT copolymers are block copolymers and the content of poly(butylene terephthalate) (PBT) units incorporated into the copolymers is always less than that in the polymerization feed. The 1,4‐butanediol consumption by a side reaction leads to a relatively lower content of PBT units in the resultant copolymers. At the same time, the PBT and poly(trimethylene terephthalate) (PTT) sequence length distributions in the copolymers are different. The PBT segments favor a longer sequence length than do the PTT segments in their corresponding enriched copolymers. The crystallization rate of the copolymers becomes lower than the homopolymers, especially for PTT‐enriched copolymers. Compared with the PTT segment, the presence of PBT segments in the copolymers seems to accelerate crystallization. A wide‐angle X‐ray diffraction (WAXD) analysis indicates PTT and PBT units do not co‐crystallize. The reduced melting temperatures of the copolymers may be attributed to a smaller lamellar thickness and lateral size due to short sequence lengths.     

Sequential Structure,Crystallization, and Properties of Biodegradable Poly(ethylene Terephthalate-Co-Ethylene Oxide-Co-Lactide) Copolyester

The sequential structure, isothermal crystallization, tensile property, and degradation behavior of poly(ethylene terephthalate-co-ethylene oxide-co-lactide) (ETOLA) copolyester based on melt transesterification of poly(ethylene terephthalate) with poly(ethylene oxide) and oligo(lactic acid) was investigated. The degree of randomness was calculated to be 0.38, showing the incorporation of poly(ethylene oxide) (PEO) blocks into the homogeneous sequences of ethylene terephthalate (ET) and lactide (LA) units. The isothermal crystallization kinetics results revealed that the crystallization activation energy of the copolyester calculated using the Arrhenius’ equation was lower than that reported for poly(ethylene terephthalate) (PET), indicating that the addition of PEO and LA units into PET retarded the crystallization of PET. The copolyester exhibited the same crystal structure at different crystallization temperatures, similar to that of PET homopolymer, based on wide angle X-ray diffraction results. The size of the spherulites of ETOLA increased with crystallization temperature. The increase of crystallization temperature reduced the elongation at break of the copolyesters, as well as the enzymatic degradation.     

Isothermal Melt Crystallization Kinetics for Poly(Trimethylene Terephthalate)/Poly(Butylene Terephthalate) Blends

The kinetics of isothermal melt crystallization of poly(trimethylene terephthalate) (PTT)/poly(butylene terephthalate) (PBT) blends were investigated using differential scanning calorimetry (DSC) over the crystallization temperature range of 184–192°C. Analysis of the data was carried out based on the Avrami equation. The values of the exponent found for all samples were between 2.0 and 3.0. The results indicated that the crystallization process tends to be two‐dimensional growth, which was consistent with the result of polarizing light microscopy (PLM). The activation energies were also determined by the Arrhenius equation for isothermal crystallization. The values of ΔE of PTT/PBT blends were greater than those for PTT and PBT. Lastly, using values of transport parameters common to many polymers (U*=6280 J/mol, T _∞=T _g – 30), together with experimentally determined values of T _m ⁰ and T _g, the nucleation parameter, K _g, for PTT, PBT, and PTT/PBT blends was estimated based on the Lauritzen–Hoffman theory.     

Influence of Polycarbonate on the Crystallization Behavior of Poly(Trimethylene Terephthalate)/Polycarbonate Blends

To determine the factors influencing the retardation of the crystallization of poly(trimethylene terephthalate) (PTT) when PTT is blended with polycarbonate (PC), different PTT/PC blends were prepared via the melt mixing method. The relationships between the crystallization behavior and blend composition, as well as the phase morphology, were investigated. The results showed that the predominant reason for the retardation in crystallization is due to the PC content and phase morphology. The PC influences the crystallization of PTT via two methods. First, it retards PTT crystallization. Secondly, the PC exhibits a nucleation effect on the PTT crystallization which is, however, much weaker compared to the negative effect PC exerts with regards to PTT crystallization. When the processing temperature and shear rate remains unchanged, the two effects of PC determine the crystallization behavior of the blend. The phase morphology, which is strongly dependent on the mixing temperature and the shear rate, and which is also related to mixing time, had an appreciable impact on PTT crystallization. In the case of similar adhesion with the interface, a finer PC phase domain would show a slightly stronger nucleation effect on PTT crystallization.     

变温FTIR光谱法研究PET/纳米CaCO_3复合材料的固态转变

采用变温FTIR光谱法研究了原料PET和PET/nano-CaCO3(MPET)复合材料体系在40~250℃之间逐渐升温过程中,PET基体的固态转变。通过研究PET内标谱带1 410 cm-1与结晶相关谱带1 342cm-1吸光度之比值随温度变化关系曲线,结合其在同样条件下的差热扫描(DSC)曲线,分析了纳米CaCO3粒子的加入对PET固态转变和结晶相关谱带的影响,表明纳米CaCO3粒子的加入显著改善了PET的结晶和熔融行为。     

Transesterification-Induced Evolution of Structure and Morphology in Poly(trimethylene terephthalate)/Poly(butylenes succinate) Blends

The evolution of the structure and morphology in poly(trimethylene terephthalate)/poly(butylene succinate) (PTT/PBS) blends induced by transesterification between PTT and PBS at different blending temperatures for 2 h and various times at 270°C was investigated. By control of the extent of transesterification, the degree of randomness, crystallization, morphology, and tensile properties of the blends could be modulated. The results indicated that the degree of randomness of the blends increased by increasing the blending temperature above 260°C and blending time, leading to the formation of copolyesters. The crystallization of the blends was restricted by the increase of blending temperature and time, shown by broad reflection peaks in X-ray spectra and less perfect spherulites as observed by polarized optical microscopy (POM), which was due to the increase of the degree of randomness. The elongation at break increased by increasing the blending time and temperature, accompanied by a decrease of tensile strength and elastic modulus, showing a dependence on the degree of randomness caused by the transesterification.     

Microstructures and Mechanical Properties of Poly(Trimethylene Terephthalate)/Maleic Anhydride Grafted Poly(Ethylene-octene)/Polypropylene Blends

A range of blends based on 70 wt% of poly(trimethylene terephthalate) PTT with 30 wt% dispersed phase were produced via melt blending. The dispersed phase composition was varied from pure maleic anhydride grafted poly(ethylene-octene) (POE-g-MA) over a range of POE-g-MA:polypropylene (PP) ratios. The micromorphology and mechanical properties of the ternary blends were investigated. The results indicated that the domains of the POE-g-MA are dispersed in the PTT matrix, and at the same time the POE-g-MA encapsulate the PP domains. The interfacial reaction between the hydroxyl-end group of PTT and maleic anhydride (MA) during melt blending changes the formation from “isolated formation” to “capsule formation,” where the PP domains are encapsulated by POE-g-MA. Compared to the PTT/POE-g-MA blends, mechanical properties of ternary blends, such as tensile strength and Young's modulus, were improved significantly.     

Effect of Organoclay Platelets on Crystallization of PTT/EPDM-g-MA Blends: Nonisothermal Melt Crystallization Kinetics

PTT/EPDM-g-MA (80/20 w/w) nanocomposites were prepared by melt mixing of poly(trimethylene terephthalate) (PTT), ethylene-propylene-diene copolymer grafted with maleic anhydride (EPDM-g-MA), and organoclay. The blend nanocomposites show typical sea-island morphologies. The nonisothermal crystallization kinetics of pure PTT and 80/20 (w/w) PTT/EPDM-g-MA blends with various amounts of the clay were extensively studied by differential scanning calorimetry (DSC). The Avrami, Ozawa, and Mo methods were used to describe the nonisothermal crystallization process of pure PTT and 80/20 (w/w) PTT/EPDM-g-MA blends with various amounts of the clay. Avrami analysis results show that the crystallization rates of 80/20 (w/w) PTT/EPDM-g-MA blends with the clay were faster than those of pure PTT or PTT/EPDM-g-MA blends without clay, which indicates that the clay particles promote crystallization effectively, in agreement with the Mo analysis results. Ozawa analysis can describe the nonisothermal crystallization of pure PTT very well but was rather inapplicable to the 80/20 (w/w) PTT/EPDM-g-MA blends with various amounts of the clay.     

Compatibilization of Poly(Trimethylene Terephthalate)/Polycarbonate Blends by Epoxy. Part 2. Melting Behavior and Spherulite Morphology

The melting behaviors of poly(trimethylene terephthalate)/polycarbonate (PTT/PC) blends, compatibilized by epoxy, and PTT spherulite morphology in the blends were investigated. When epoxy was present during blending, the melting behaviors of PTT/PC blends changed substantially; glass transition temperatures (T_g's) and cold crystallization temperature (T_cc's) of the PTT‐rich phase shifted to higher temperatures, while T_m's shifted slightly to lower temperatures, indicating that epoxy suppressed considerably all processes of dynamic movements pertinent to molecular (or segmental) movements. The cold crystallization process responded sensitively to thermal history. Changes of T_cc's with composition suggested that the epoxy's compatibilization effect was pronounced when PTT and PC were in near equal content.

Recrystallization or reorganization exotherms appeared before melting for isothermally crystallized PTT/PC and PTT/PC epoxy (E) blends. A wide angle X‐ray diffraction (WAXD) analysis showed that, although the perfection of PTT crystallites was influenced either by PC content and the presence of compatibilizer or by the crystallization temperature and crystallization time, PTT's crystal structure was independent of these variables.

The polarized light microscopy (PLM) observations showed that PTT spherulite morphology was very sensitive to blend composition. Epoxy addition interfered severely with the growth of PTT spherulites, causing them to be much less developed. When the spherulites grew under a condition of varied composition, they would exhibit diversified spherulite morphology, though in one spherulite.     

Preparation and Properties of Poly(ethylene terephthalate)/Silica Nanocomposites

A kind of poly(ethylene terephthalate) (PET)/Silica nanocomposite (PETS) was synthesized via in situ polymerization using the compatibility between silica nanoparticles and ethylene glycol (EG). Transmission electron microscopy (TEM) micrographs revealed that the silica nanoparticles were well dispersed in the PET matrix, the particle size was about 10 nm with narrow distribution, and there existed strong interaction between the particles and the polymer chains. Differential scanning calorimetry (DSC) results indicated that the thermal properties of PETS with 2 wt% silica (PETS‐2) are different from those of pure PET (PETS‐0). The properties of the as‐spun fibers show that the tenacity and LASE‐5 (load at a specified elongation of 5%) of PETS‐2 were higher than those of PETS‐0, while the heat shrinkage of PETS‐2 was lower than that of PETS‐0. We suggest that the increasing of crystallinity and the strong interface interaction of the nanocomposite caused the fibers of PETS‐2 to not only have higher tenacity and LASE‐5 but also to have lower heat shrinkage.     

Thin-layer chromatography of copolyesters from blends of poly(ethylene terephthalate)/polycarbonate

Copolymers made by ester exchange reaction have been obtained from poly(ethylene terephthalate) (PET)/poly(bis-phenol-A carbonate) (PC) blends during melt mixing. The copolyesters were isolated by thin-layer chromatography (TLC) and identified by infrared spectroscopy. It was found that the quantity of copolymer formed was increased by the temperature and duration of melt mixing. The PET/PC blend was found to react at 270°C within 10 min, as detected by TLC. After 60 min, the pure PC had disappeared. The miscibility of PET/PC blends was found to be markedly aided by the addition of as little as 2% of the copolymer isolated by TLC.     

The Nucleation Effect of Grafted Carbon Black on Crystallization of Poly(Ethylene Terephthalate)/Grafted Carbon Black Composite

Poly(ethylene terephthalate)/grafted carbon black (PET/GCB) and poly(ethylene terephthalate)/carbon black (PET/CB) composites were prepared by melt blending. The nucleating effect of CB and GCB were investigated using differential scanning calorimetry (DSC) analysis. The morphologies of the spherulites in PET, PET/CB and PET/GCB composites were observed by means of scanning electron microscopy (SEM). All results showed that GCB had higher nucleating activity than CB in PET and PET/GCB composite had higher rate of nucleation and crystallization. The melting behaviors of neat PET, PET/CB and PET/GCB composites after non‐isothermal crystallization were investigated as well. It was evident that the melting behavior of PET is greatly influenced by addition of CB and GCB.