Toughened Poly(Trimethylene Terephthalate) by Blending with a Functionalized Metallocenic Poly(Ethylene-Octene) Copolymer

New toughened poly(trimethylene terephthalate) (PTT) materials were obtained by melt blending with maleic anhydride grafted poly(ethylene-octene) (POEg). Rheological properties, mechanical properties, and morphological characteristics of PTT/POEg blends at four different compositions—95/5, 90/10, 80/20, and 70/30—were studied. The melt viscosity of the blends shows a linear decrease on increasing the POEg content. The addition of rubbery POEg to the PTT matrix increases the impact strength, while tensile properties decrease. Scanning electron microscopy (SEM) displayed a very good dispersion of POEg particles in the PTT matrix. Differential scanning colorimetry (DSC) experiments showed that for all samples the melting point was almost constant and the crystallinity did not show obvious differences. SEM results showed shear yielding of the PTT matrix was the major toughening mechanism.     

Effects of Montmorillonite on the Nonisothermal Crystallization Behavior of the Poly(trimethylene terephthalate)/Polypropylene/Montmorillonite Nanocomposites

Organic montmorillonite (MMT) reinforced poly(trimethylene terephthalate) (PTT)/ polypropylene (PP) nanocomposites were prepared by melt blending. The effects of MMT on the nonisothermal crystallization of the matrix polymers were investigated using differential scanning colorimetry (DSC) and analyzed by the Avrami equation. The DSC results indicated that the effects of MMT on the crystallization processes of the two polymers exhibited great disparity. The PTT's crystallization was accelerated significantly by MMT no matter whether PTT was the continuous phase or not, but the thermal nucleation mode and three-dimensional growth mechanism remained unchanged. However, in the presence of MMT, the PP's crystallization was slightly retarded with PP as the dispersed phase, and was influenced little with PTT as the dispersed phase. When the MMT content was increased from 2_wt% to 7_wt%, the crystallization of the PTT phase was slightly accelerated, whereas the crystallization of the PP phase was severely retarded, especially at lower temperatures. Moreover, the nucleation mechanism for the PP's crystallization changed from a thermal mode to an athermal one. In the polypropylene-graft-maleic anhydride (PP-g-MAH) compatibilized PTT/PP blends, with the addition of 2_wt% MMT during melt blending, the T _c (PTT) shifted 7.8°C to lower temperature and had a broadened exotherm, whereas the T _c (PP) shifted 17.1°C to higher temperature, with a narrowed exotherm. TEM analysis confirmed that part of the PP-g-MAH was combined with MMT during blending.     

Effect of Maleated Styrene/Ethylene-co-Butylene/Styrene on the Dispersed Particles Size and Mechanical Properties of Polyamide 6/Poly(styrene-co-acrylonitrile)/Poly(styrene-b-(ethylene-co-butylene)-b-styrene) Ternary Blends

In this study, the effect of several parameters, including composition, order of mixing, viscosity, and interfacial tension, on the phase structure and size of dispersed particles of polyamide 6 (PA6)/poly(styrene-co-acrylonitrile) SAN/poly(styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS) ternary blends was investigated. Moreover, the effect of addition of different ratios of reactive SEBS (maleic anhydride grafted-SEBS) and non-reactive SEBS at a fixed order of mixing and composition of 70/15/15 (PA6/SAN/SEBS + SEBS-g-MAH) on the mechanical properties of ternary blends was examined. Scanning electron microscopy (SEM) micrographs showed that among the studied parameters, interfacial tension and viscosity of dispersed phases were the leading factors in the formation of morphology and size of dispersed droplets. Mechanical results revealed that in contrast to the expectation, formation of core/shell structure of PA6/SAN/SEBS ternary blends did not result in a significant increasing of impact strength. The highest impact strength was achieved when a 50/50 weight ratio of SEBS/SEBS-g-MAH was used.     

Morphological and Rheological Properties of Poly(Trimethylene Terephthalate)/Maleic Anhydride Grafted Poly (Ethylene-Octene)/Organoclay Ternary Nanocomposite

Poly(trimethylene terephthalate) (PTT)/poly(ethylene-octene) POE-g-MA/organoclay ternary nanocomposites were prepared using melt blending in order to simultaneously improve the toughness and stiffness of PTT. The phase morphology and dispersion of organoclay were characterized by scanning electron microscope (SEM), X-ray diffractometer (XRD), and transmission electron microscopy (TEM). The melt rheological behavior of the ternary nanocomposites was determined by plate/plate rheological measurements. XRD and TEM analysis indicated that the ternary nanocomposites contained exfoliated nanoparticle when a small amount of organoclay (1 part per hundred) was added. The high aspect ratio of the organoclay platelets induced the average size of the dispersed domain to become smaller. Melt rheological studies revealed that the ternary nanocomposites exhibited strong shear thinning behavior and showed good processability.     

Reactive Compatibilization of Poly(trimethylene terephthalate)/Polypropylene Blends by Polypropylene‐graft‐Maleic Anhydride. Part 1. Rheology,Morphology, Melting,and Mechanical Properties

Poly(trimethylene terephthalate)/polypropylene (PTT/PP) blends were prepared by melt blending. The rheology, morphology, melting, and mechanical properties of PTT/PP blends were investigated with and without the addition of polypropylene‐graft‐maleic anhydride (PP‐g‐MAH). The melt viscosity results showed that the fluid behavior of PTT/PP blends exhibited great disparity to that of PTT but similar to that of PP; the dispersed flexible PP phase in the blends served as a “ball bearing effect” under shear stress, which made the fluid resistance markedly reduced; by contrast, the relatively rigid PTT dispersed phase made only a small contribution to the viscosity. With 5 wt.% PP‐g‐MAH addition during melt processing, both the shear viscosity and the non‐Newtonian index of 70/30 PTT/PP blend were increased over that of the corresponding uncompatibilized one, whereas the shear viscosity of the 30/70 PTT/PP melt decreased slightly indicating that a considerable amount of PP‐g‐MAH did not act as compatibilizer but probably served as plasticizer.

With the increasing of the other component, the melting temperature of the PTT phase showed a slight decrease while the melting temperature of the PP phase showed a slight increase. 5 wt.% PP‐g‐MAH addition had little influence on the melting temperatures of the two components. When PP≤20 wt.%, the cold crystallization temperature of the PTT phase (T_cc (PTT‐phase)) showed little change with the composition; however, it shifted to higher temperature when PP≥30 wt.%. The variations of the T_cc (PTT‐phase), with and without PP‐g‐MAH, suggested that, when PTT was a minor component, the excess PP‐g‐MAH which did not act as compatibilizer might serve as a plasticizer that made the PTT's cold crystallization process to be easier. The SEM results indicated that, for the uncompatibilized blends, the interfaces from particles pulling‐out are clear and smooth, while, for compatibilized blends, the reactive products are at the interfaces. The mechanical properties suggested that PP‐g‐MAH did not result in significant improvement of the toughness of the blend, but the tensile strength increased markedly.     

Preparation,Morphology and Properties of Poly(Trimethylene Terephthalate)/Thermoplastic Polyester Elastomer Blends

Poly(trimethylene terephthalate)(PTT)/thermoplastic polyester elastomer (TPEE) blends were prepared and their miscibility, crystallization and melting behaviors, phase morphology, dynamic mechanical behavior, rheology behavior, spherulites morphology, and mechanical properties were investigated by differential scanning calorimetry (DSC), scanning electron microscopy (SEM), dynamic mechanical analysis (DMA), parallel-plate rotational rheometry, polarized optical microscopy (POM), wide angle X-ray diffraction (WAXD), universal tensile tester and impact tester, respectively. The results suggested that PTT and TPEE were partially miscible in the amorphous state, the TPEE rich phase was dispersed uniformly in the solid matrix with a size smaller than 2 μm, and the glass transition temperatures of the blends decreased with increasing TPEE content. The TPEE component had a good effect on toughening the PTT without depressing the tensile strength. The blends had improved melt viscosities for processing. When the blends crystallized from the melt state, the onset crystallization temperature decreased, but they had a faster crystallization rate at low temperatures. All the blends’ melts exhibited a predominantly viscous behavior rather than an elastic behavior, but the melt elasticity increased with increasing TPEE content. When the blends crystallized from the melt, the PTT component could form spherulites but their morphology was imperfect with a small size. The blends had larger storage moduli at low temperatures than that of pure PTT.     

Miscibility,Morphology, and Thermal Properties of Poly(Trimethylene Terephthalate)/Polycarbonate

Abstract

Poly(trimethylene terephthalate)/polycarbonate (PTT/PC) blends were prepared by melt blending and rapid quenching in ice water. The miscibility and thermal properties were investigated using differential scanning calorimeter (DSC) and dynamic mechanical analysis (DMA). The blend's morphologies were investigated using scanning and transmission electron microscopies. Both DSC and DMA results suggested that PTT and PC were very limited, partially miscible pairs. The melting point, melt crystallization, and cold crystallization exotherms in the blends of PTT were depressed by the presence and amount of PC. When the PC content was <50 wt%, PC spherical particles were found to distribute evenly in the PTT matrix; at 50–60 wt%, the two‐phase structures were close to being bicontinuous. At higher PC content, PTT formed a string‐like texture in the PC matrix. The PTT spherulitic morphologies in PTT/PC blends were found to be very sensitive to PC and PC content. When the PC content was ≥60 wt%, the blends crystallized as an agglomeration of tiny PTT crystals.     

Effect of Organoclay Platelets on Crystallization of Polytrimethylene Terephthalate/Polyethylene-octene-g-maleic Anhydride Blends: Isothermal Crystallization

The blends of poly(trimethylene terephthalate) (PTT) with maleic anhydride-grafted poly(ethylene-octene) (POE-g-MA) and organoclay (OMMT) were prepared by melt-blending. The effects of organoclay platelets on the isothermal crystallization behaviors of PTT/POE-g-MA blend were examined using differential scanning calorimetry. The crystallization kinetics of the primary stage under isothermal conditions could be described by the Avrami equation, with values of the Avrami exponent between 2.01 and 2.81 for all samples. The crystallization rate parameter, K, decreased with increase of melt-crystallization temperature for all samples. The activation energies for isothermal crystallization were determined by the Arrhenius equation.     

Fabrication of Polypropylene/Poly (Trimethylene Terephthalate) Blend Fibers with Highly Improved Resiliency and Preserved Mechanical Properties

The main aim of this study was to deal with one of the major drawbacks of polypropylene (PP) fibers, i.e. low resiliency, by incorporating poly (trimethylene terephthalate) (PTT) nano-fibrils as a dispersed material into the PP polymer matrix. Thanks to the special helical shape of the PTT polymer backbone, the incorporated nano-fibrils of the PTT polymer strengthened the resiliency of the blend fibers. The presence of 10 and 15?wt% of PTT in the blend fibers led to an approximately 20% increase in the resilience behavior, compared to pure PP fibers, with the mechanical properties of the PP matrix preserved. The development of the fibrillar structures during the different steps of the melt spinning process was confirmed by scanning electron microscopy (SEM), and the lowest mean diameter of the nano-fibrils was 64?nm for the hot drawn blend fiber samples consisting of 10?wt% of PTT. In summary, we suggest the optimized blend fiber samples produced in this research will be a promising candidate for a wide range of engineering applications.     

Polypropylene/Poly (Trimethylene Terephthalate)–Blend Fibers

Polypropylene (PP)/polyester (PES)–blend fibers were prepared by extruder melt spinning. The polymer blend consisted of PP and a “master batch” (MB) based on polytrimethylene terephthalate (PTT) or polyethylene terephthalate (PET), binary PTT/PET or PP/PTT blends, and also on a ternary PP/(PTT/PET) blend. The phase structure of PP/PES–blend fibers was examined. PES microfibers showed separation from the PP matrix in blend fibers. The impact of MB composition and rheological characteristics on phase structure parameters indicate a significant contribution of the PTT in the binary MB on the length of dispersed PES microfibers in the PP matrix. However, the blends of PP and ternary MB (PP/PTT/PET) have a lower diameter and length of the PES microfibers. The presence of PTT/PET (PES) enhances the structural and mechanical properties of the blend PP/PES fibers. In addition, PTT increases the tensile strength of the PP/PES–blend fibers if a binary MB is used, while the fiber nonuniformity is reduced in the presence of a ternary MB.     

Reactive Compatibilization of Poly(trimethylene terephthalate)/Polypropylene Blends by Polypropylene‐graft‐Maleic Anhydride. Part 2. Crystallization Behavior

The crystallization behavior of uncompatibilized and reactive compatibilized poly(trimethylene terephthalate)/polypropylene (PTT/PP) blends was investigated. In both blends, PTT and PP crystallization rates were accelerated by the presence of each other, especially at low concentrations. When PP content in the uncompatibilized blends was increased to 50–60 wt%, PTT showed fractionated crystallization; a small PTT crystallization exotherm appeared at ～135°C besides the normal ～175°C exotherm. Above 70 wt% PP, PTT crystallization exotherms disappeared. In contrast, PP in the blends showed crystallization exotherms at 113–121°C for all compositions. When a maleic anhydride‐grafted PP (PP‐g‐MAH) was added as a reactive compatibilizer, the crystallization temperatures (T _c ) of PTT and PP shifted significantly to lower temperatures. The shift of PTT's T _c was larger than that of the PP, suggesting that addition of the PP‐g‐MAH had a larger effect on PTT's crystallization than on PP due to reaction between maleic anhydride and PTT.

The nonisothermal crystallization kinetics was analyzed by a modified Avrami equation. The results confirmed that PTT's and PP's crystallization was accelerated by the presence of each other and the effect varied with blend compositions. When the PP content increased from 0 to 60 wt%, PTT's Avrami exponent n decreased from 4.35 to 3.01; nucleation changed from a thermal to an athermal mode with three‐dimensional growths. In contrast, when the PTT content increased from 0 to 90 wt% in the blends, changes in PP's n values indicated that nucleation changed from a thermal (0–50 wt% PTT) to athermal (60–70 wt% PTT) mode, and then back to a thermal (80–90 wt% PTT) mode. When PP‐g‐MAH was added as a compatibilizer, the crystallization process shifted considerably to lower temperatures and it took a longer crystallization time to reach a given crystallinity compared to the uncompatibilized blends.     

Isothermal Melt Crystallization Kinetics for Poly(Trimethylene Terephthalate)/Poly(Butylene Terephthalate) Blends

The kinetics of isothermal melt crystallization of poly(trimethylene terephthalate) (PTT)/poly(butylene terephthalate) (PBT) blends were investigated using differential scanning calorimetry (DSC) over the crystallization temperature range of 184–192°C. Analysis of the data was carried out based on the Avrami equation. The values of the exponent found for all samples were between 2.0 and 3.0. The results indicated that the crystallization process tends to be two‐dimensional growth, which was consistent with the result of polarizing light microscopy (PLM). The activation energies were also determined by the Arrhenius equation for isothermal crystallization. The values of ΔE of PTT/PBT blends were greater than those for PTT and PBT. Lastly, using values of transport parameters common to many polymers (U*=6280 J/mol, T _∞=T _g – 30), together with experimentally determined values of T _m ⁰ and T _g, the nucleation parameter, K _g, for PTT, PBT, and PTT/PBT blends was estimated based on the Lauritzen–Hoffman theory.     

Improving the Barrier Properties of Poly(Lactic Acid) by Blending with Poly(Ethylene-Co-Vinyl Alcohol)

Poly(lactic acid) (PLA)/poly(ethylene-co-vinyl alcohol) (EVOH) blends were prepared via melt blending to improve the barrier properties of PLA. The phase morphologies and final properties (rheological behavior, thermal and dynamical-mechanical features, barrier properties, and mechanical behaviors) of the blends were investigated as a function of the EVOH content. The results indicated that hydroxyl groups of EVOH promoted the degradation of PLA, and thus affected the viscosities and morphologies of the resulting blends. The intrinsic viscosities of PLA in the blends decreased with the content of EVOH. The PLA and EVOH presented typical phase-separated morphologies, with a relatively small domain size of the EVOH phase. The EVOH enhanced the cold-crystallization behavior of PLA. The barrier properties to water vapor and oxygen increased linearly with increasing EVOH content.     

Influence of Polycarbonate on the Crystallization Behavior of Poly(Trimethylene Terephthalate)/Polycarbonate Blends

To determine the factors influencing the retardation of the crystallization of poly(trimethylene terephthalate) (PTT) when PTT is blended with polycarbonate (PC), different PTT/PC blends were prepared via the melt mixing method. The relationships between the crystallization behavior and blend composition, as well as the phase morphology, were investigated. The results showed that the predominant reason for the retardation in crystallization is due to the PC content and phase morphology. The PC influences the crystallization of PTT via two methods. First, it retards PTT crystallization. Secondly, the PC exhibits a nucleation effect on the PTT crystallization which is, however, much weaker compared to the negative effect PC exerts with regards to PTT crystallization. When the processing temperature and shear rate remains unchanged, the two effects of PC determine the crystallization behavior of the blend. The phase morphology, which is strongly dependent on the mixing temperature and the shear rate, and which is also related to mixing time, had an appreciable impact on PTT crystallization. In the case of similar adhesion with the interface, a finer PC phase domain would show a slightly stronger nucleation effect on PTT crystallization.     

Miscibility and Isothermal Crystallization Behavior of Poly (Butylene Succinate-co-Adipate) (PBSA)/Poly (Trimethylene Carbonate) (PTMC) Blends

Poly(butylene succinate-co-adipate) (PBSA)/poly (trimethylene carbonate) (PTMC) blend samples with different weight ratios were prepared by solution blending. The morphologies after isothermal crystallization and in the melt were observed by optical microscopy (OM). Differential scanning calorimetry (DSC) was used to characterize the isothermal crystallization kinetics and melting behaviors. According to the OM image before and after melting, it was found that the blends formed heterogenous morphologies. When the PTMC content was low (20%), PBSA formed the continuous phase, while when the PTMC contents was high (40%), PBSA formed the dispersed phase. The glass transition temperatures (T_g) of the blends were determined by DSC and the differences of the T_g values were smaller than the difference between those of pure PBSA and PTMC. In addition, the equilibrium melting points were depressed in the blends. According to these results, the PBSA/PTMC blends were determined as being partially miscible blends. The crystallization kinetics was investigated according to the Avrami equation. It was found that the incorporation of PTMC did not change the crystallization mechanism of PBSA. However, the crystallization rate decreased with the increase of PTMC contents. The change of crystallization kinetics is related with the existences of amorphous PTMC, the partial miscibility between PLLA and PTMC, and the changes of phase structures.     

Effect of Organoclay Platelets on Crystallization of PTT/EPDM-g-MA Blends: Nonisothermal Melt Crystallization Kinetics

PTT/EPDM-g-MA (80/20 w/w) nanocomposites were prepared by melt mixing of poly(trimethylene terephthalate) (PTT), ethylene-propylene-diene copolymer grafted with maleic anhydride (EPDM-g-MA), and organoclay. The blend nanocomposites show typical sea-island morphologies. The nonisothermal crystallization kinetics of pure PTT and 80/20 (w/w) PTT/EPDM-g-MA blends with various amounts of the clay were extensively studied by differential scanning calorimetry (DSC). The Avrami, Ozawa, and Mo methods were used to describe the nonisothermal crystallization process of pure PTT and 80/20 (w/w) PTT/EPDM-g-MA blends with various amounts of the clay. Avrami analysis results show that the crystallization rates of 80/20 (w/w) PTT/EPDM-g-MA blends with the clay were faster than those of pure PTT or PTT/EPDM-g-MA blends without clay, which indicates that the clay particles promote crystallization effectively, in agreement with the Mo analysis results. Ozawa analysis can describe the nonisothermal crystallization of pure PTT very well but was rather inapplicable to the 80/20 (w/w) PTT/EPDM-g-MA blends with various amounts of the clay.     

Crystallization Behavior of Poly(Trimethylene Terephthalate)/Polycarbonate Blends

The crystallization behavior of poly(trimethylene terephthalate (PTT) in compatibilized and uncompatibilized PTT/polycarbonate (PC) blends are investigated in the research reported in this paper. The differential scanning calorimetry (DSC) results showed that the crystallization behaviors of PTT/PC blends were very sensitive to PC content. The onset (T_ci) and the peak (T_c) crystallization temperatures shifted to lower temperatures whereas the area of the exotherm decreased quickly as the PC content was increased. The Avrami exponent, n, decreased from 4.32 to 3.61 as the PC content was increased from 0 to 20 wt %, and the growth rate constant, Z _c , decreased gradually as well. This suggests that the nucleation mechanism exhibits the tendency of changing gradually from a thermal nucleation to an athermal mode although the growth mechanism still remains three‐dimensional. When epoxy (2.7 phr) was added as a compatibilizer during melt blending, the T_ci and T_c shifted slightly to higher temperature (≤2°C), and the crystallization enthalpy, however, exhibited an increased crystallinity with the exception of the 90/10/2.7 phr PTT/PC/Epoxy. This suggests that the epoxy make a positive contribution to the PTT crystallization. Moreover, the influences of epoxy on the crystallization behaviors of PTT/PC blends are related to the epoxy content. By contrast, the compatibilizer of ethylene‐propylene‐diene copolymer graft glycidyl methacrylate (EPDM‐g‐GMA, ≤6.3 phr) had little effect on the crystallization behavior of PTT/PC blends. For PTT/PC/Epoxy (2.7 phr) blends, the Avrami exponent, n, decreased to near 3, while the growth rate constant, Z _c , increased slightly as PC content was increased from 0 to 20 wt %. It is suggested that epoxy accelerated the process of the nucleation mechanism changing from thermal nucleation to an athermal mode. The EPDM‐g‐GMA had little effect on the nucleation mode and spherical growth mechanism. The PTT spherulite morphologies in PTT/PC blends were very sensitive to blend composition. Completely different morphologies were observed in pure PTT, PTT/PC, PTT/PC/Epoxy, and PTT/PC/EPDM‐g‐GMA blends.     

Transesterification-Induced Evolution of Structure and Morphology in Poly(trimethylene terephthalate)/Poly(butylenes succinate) Blends

The evolution of the structure and morphology in poly(trimethylene terephthalate)/poly(butylene succinate) (PTT/PBS) blends induced by transesterification between PTT and PBS at different blending temperatures for 2 h and various times at 270°C was investigated. By control of the extent of transesterification, the degree of randomness, crystallization, morphology, and tensile properties of the blends could be modulated. The results indicated that the degree of randomness of the blends increased by increasing the blending temperature above 260°C and blending time, leading to the formation of copolyesters. The crystallization of the blends was restricted by the increase of blending temperature and time, shown by broad reflection peaks in X-ray spectra and less perfect spherulites as observed by polarized optical microscopy (POM), which was due to the increase of the degree of randomness. The elongation at break increased by increasing the blending time and temperature, accompanied by a decrease of tensile strength and elastic modulus, showing a dependence on the degree of randomness caused by the transesterification.     

Influence of halloysite nanotubes (HNTs) on morphology,crystallization, mechanical and thermal behaviour of PP/ABS blends and its composites in presence and absence of dual compatibilizer

Halloysite nanotubes (HNTs) filled 80/20 (wt/wt) polypropylene (PP)/acrylonitrile butadiene styrene (ABS) blends and its composites in presence and absence of dual compatibilizer (polypropylene grafted maleic anhydride (PP-g-MA), and styrene-ethylene, butylene-styrene triblock copolymer grafted with maleic anhydrite (SEBS-g-MA)) have been prepared using twin screw extruder followed by injection moulding. Significant refinements in dispersed ABS droplets diameter and interparticle distance between dispersed ABS droplets were observed in case of HNTs filled 80/20 (wt/wt) PP/ABS blends and its composites in presence of PP-g-MA and SEBS-g-MA. This has resulted in significant enhancement in tensile and impact properties of HNTs filled 80/20 (wt/wt) PP/ABS blends and its composites in presence of PP-g-MA and SEBS-g-MA. Refinement in morphology of dispersed ABS phase results in decrease in crystallinity of HNTs filled 80/20 (wt/wt) PP/ABS blends and its composites in presence of PP-g-MA and SEBS-g-MA. In addition, HNTs act as heterogeneous nucleating agent for the growth of PP crystals, and hence crystallization rate of HNTs filled 80/20 (wt/wt) PP/ABS blends and its composites in presence and absence of PP-g-MA and SEBS-g-MA increases. Thermal stability also increases in case of HNTs filled 80/20 (wt/wt) PP/ABS blends and its composites in presence and absence of PP-g-MA and SEBS-g-MA.     

Compatibilization of Poly(Trimethylene Terephthalate)/Polycarbonate Blends by Epoxy. Part 2. Melting Behavior and Spherulite Morphology

The melting behaviors of poly(trimethylene terephthalate)/polycarbonate (PTT/PC) blends, compatibilized by epoxy, and PTT spherulite morphology in the blends were investigated. When epoxy was present during blending, the melting behaviors of PTT/PC blends changed substantially; glass transition temperatures (T_g's) and cold crystallization temperature (T_cc's) of the PTT‐rich phase shifted to higher temperatures, while T_m's shifted slightly to lower temperatures, indicating that epoxy suppressed considerably all processes of dynamic movements pertinent to molecular (or segmental) movements. The cold crystallization process responded sensitively to thermal history. Changes of T_cc's with composition suggested that the epoxy's compatibilization effect was pronounced when PTT and PC were in near equal content.

Recrystallization or reorganization exotherms appeared before melting for isothermally crystallized PTT/PC and PTT/PC epoxy (E) blends. A wide angle X‐ray diffraction (WAXD) analysis showed that, although the perfection of PTT crystallites was influenced either by PC content and the presence of compatibilizer or by the crystallization temperature and crystallization time, PTT's crystal structure was independent of these variables.

The polarized light microscopy (PLM) observations showed that PTT spherulite morphology was very sensitive to blend composition. Epoxy addition interfered severely with the growth of PTT spherulites, causing them to be much less developed. When the spherulites grew under a condition of varied composition, they would exhibit diversified spherulite morphology, though in one spherulite.