Investigation of interfacial adhesion in nylon-6 fibre/NBR composites through restricted equilibrium swelling technique

Short nylon-6 fibre reinforced acrylonitrile butadiene rubber (NBR) composites were prepared and the interfacial adhesion was evaluated by the restricted solvent swelling technique. The solvents used were N,N-dimethyl formamide (DMF), dimethyl sulphoxide (DMSO) and acetonitrile. As the fibre content increased, the solvent uptake decreased, which has been attributed to the increased hindrance to solvent penetration due to better fibre–rubber interaction. It was observed that the ratio of change in volume fraction of rubber before and after swelling to the volume fraction of rubber before swelling (V ₀ – V _r/V ₀) was lower for a bonding agent added composite, compared to the unbonded one. Anisotropic swelling studies were carried out to analyze the extent of fibre alignment and fibre–matrix interaction. It was seen that in strongly bonded composites, the swelling mainly took place in the thickness direction. The rubber–fibre interaction has also been examined by the Lorenz–Parks and Kraus equations.     

Investigation on interfacial adhesion of short sisal/coir hybrid fibre reinforced natural rubber composites by restricted equilibrium swelling technique

Interfacial adhesion of sisal/coir hybrid fibre reinforced natural rubber (NR) composites has been characterized by restricted equilibrium swelling technique with special reference to the effects of fibre loading, orientation and bonding agent. The swelling parameters of NR composites with and without bonding agent were evaluated with three aromatic solvents, namely; benzene, toluene and xylene, by a sorption gravimetric method. As fibre content and penetrant size increase, the solvent uptake has been found to decrease due to the increased hindrance and good fibre–rubber interaction. The bonding agent added mixes showed enhanced restriction to swelling and it is seen that the ratio of change in volume fraction of rubber before and after swelling to the volume fraction of rubber before swelling (V ₀ – V _r/V ₀) is lower for bonding agent added composites, when compared to an unbonded one. The anisotropic swelling studies were carried out to analyse the extent of fibre alignment and fibre–matrix interaction. In strongly bonded composites, the swelling has been mainly observed to take place in the thickness direction, as attested by optical photographs. The rubber–fibre interaction has also been examined by Lorenz–Parks and Kraus equations.     

胆红素络合物的表面增强拉曼光谱研究

本文通过对近红外激发傅里叶变换拉曼光谱(NIR-FT-Raman)与表面增强拉曼散射(Surface Enhanced Raman Scattering,SERS)技术的联用,测得胆红素及其络合物Na     

Growth fusion of submicron spherical boron carbide particles by repetitive pulsed laser irradiation in liquid media

We studied the fabrication of B₄C submicron particles by laser irradiation of boron nanoparticles dispersed in an organic solvent. The spherical shape of the formed particles suggests that instantaneous melt formation and solidification by quenching are involved in the particle-forming process. B₄C particles gradually became larger with irradiation time at relatively low laser fluence (1.5 J cm⁻² pulse⁻¹) by repetitive melting and fusion of the particles, and the B₄C yield increased with irradiation time to 90% for 600 min of irradiation. At higher laser fluences, the B₄C yield decreased due to the explosive ablation of boron or B₄C to form H₃BO₃, and thus only the larger B₄C particles were observed. The dielectric constant of the organic solvent also affected the generated B₄C particle size, probably due to the degree of particle aggregation. Thus, this technique can provide a new approach for fabricating spherical submicron particles of ceramic materials, such as carbides, with simple and safe processes.     

胆结石的FT－Raman光谱研究

胆结石的ＦＴ－Ｒａｍａｎ光谱研究徐智勇，李维红，王立波，许振华，吴瑾光（北京大学化学与分子工程学院，稀土材料化学与应用国家重点实验室北京１００８７１）ＴｈｅＩｄｅｎｔｉｆｉｃａｔｉｏｎｏｆＴｈｒｅｅＤｉｆｆｅｒｅｎｔＴｙｐｅｓｏｆＧａｌｌｓｔｏｎｅｓ...     

Effect of curing temperature,fibre loading and bonding agent on the equilibrium swelling of isora-natural rubber composites

Isora fibre-reinforced natural rubber (NR) composites were cured at 80, 100, 120 and 150°C using a low temperature curing accelerator system. Composites were also prepared using a conventional accelerator system and cured at 150°C. The swelling behavior of these composites at varying fibre loadings was studied in toluene and hexane. Results show that the uptake of solvent and volume fraction of rubber due to swelling was lower for the low temperature cured vulcanizates which is an indication of the better fibre/rubber adhesion. The uptake of aromatic solvent was higher than that of aliphatic solvent, for all the composites. As the fibre content increased, the solvent uptake decreased, due to the superior solvent resistance of the fibre and good fibre–rubber interactions. The bonding agent improved the swelling resistance of the composites due to the strong interfacial adhesion. Due to the improved adhesion between the fibre and rubber, the ratio of the change in volume fraction of rubber due to swelling to the volume fraction of rubber in the dry sample (V_τ ) was found to decrease in the presence of bonding agent. At a fixed fibre loading, the alkali treated fibre composite showed a lower percentage swelling than untreated one for both systems showing superior rubber–fibre interactions.     

Influence of synthesis temperature on the granulometric composition of a Ba0.65Sr0.35TiO3 pigment and the optical properties and radiation resistance of pigment-based coatings

The influence of synthesis temperature on the granulometric composition of a Ba_0.65Sr_0.35Ti O₃ pigment and the optical properties and radiation resistance of pigment-based coatings has been analyzed. It has been found that a rise in synthesis temperature decreases the sizes of pigment particles, deteriorates the reflectance of the coatings, and enhances their radiation resistance.     

Assessment of LIBS for Spectrochemical Analysis: A Review

Abstract

This review assesses the applications of laser-induced breakdown spectroscopy (LIBS) for the analysis of a variety of samples, including biomaterials (teeth, nail, hair, gallstones, and kidney stones, etc.), food materials (fruits and vegetables, milk, salt, nutritional supplements, etc.), medicinal plants, industrial waste, liquid samples, etc. In addition, for the first time the identification of cholesterol and pigment stones was performed on the basis of atomic lines of different elements and molecular bands of C₂ molecules present in the LIBS spectra of gallstones. Chemometric techniques such as principal component analysis (PCA) was also applied to LIBS data for rapid identification/classification of different gallstone samples. LIBS analysis of toxic/heavy elements present in vegetables (spinach, tomato) and rice is also presented in this review. It was observed that vegetables grown near industrial areas are rich in several toxic metals like Pb and Cr. The wastewater samples from different industries were also analyzed by recording their spectra using a liquid jet. These results clearly demonstrate the ability of LIBS technique as an instant monitoring device to detect heavy metals present in liquid samples. Finally, this review shows that LIBS is a versatile analytical technique with unlimited applications.     

徐州地区胆结石的溶剂萃取的FTIR研究

胆石病是徐州地区的多发病之一,针对徐州地区临床术中取出的五类胆结石利用系列溶剂萃取,用傅里叶变换红外光谱(FTIR)分别表征萃取前后的成分、结构及形态变化。结果表明:所取的五类徐州地区胆结石分别为胆固醇型、难溶物分别为胆红素盐、蛋白质的胆固醇为主的混合型、棕色色素型和黑色色素型胆结石。蛋白质为胆结石的形成提供沉淀基质,对于胆结石成核具有重要意义;胆结石难溶物中胆固醇和羟基碳酸磷灰石相伴而生,羟基磷灰石与胆固醇存在相互作用,促使其结晶析出,从而加速胆结石的形成。结果可以为胆结石的临床诊断、治疗及预防提供一定的参考。     

钇复合氧化物颜料的制备与表征

通过尿素分解法,把三价铬离子掺入到钇铝石榴石Y₃Al₅O₁₂中,采用共沉淀法制备出绿色颜料。扫描电镜测试表明产物颗粒直径在200 nm左右,用XRD测试复合氧化物的结晶相行为,确定主相是钇铝石榴石相,用紫外可见漫反射光谱测试掺杂离子的配位状态和电子跃迁行为,用色度学测试氧化物颜色特征。将复合氧化物颜料颗粒与高分子聚丙烯共混,熔体纺丝,并通过北京同步辐射X射线CT对制得的纤维加以测试,结果表明复合氧化物颜料在高分子基质中得到良好的分散。这种颜料性能稳定,对环境友好,为实现无水印染技术奠定基础,减少纺织印染工业中所排放的污水。     

The stress-optical coefficient and amorphous order

The calculated stress-optical coefficients obtained using the rotational isomer model and the principle of additivity of bond polarizability tensors give values of the segment polarizability anisotropy, Δ T_Sin reasonable agreement with experimental values for swollen rubber networks. Furthermore, these values agree well with those obtained from streaming birefringence studies. Estimates of the effect of ordering in the amorphous state upon Δ T_S lead to values appreciably in excess of those found experimentally. The effect of swelling solvent on Δ T_S can be interpreted in terms of its role in separating chains from each other and in itself being oriented by the polymer chain. This model accounts for the observation that Δ T_S increases with increasing anisotropy of the swelling solvent. The value of Δ T_S found for networks swollen with an isotropic solvent is approximately, but not exactly, equal to the intrinsic anisotropy of the segment, Δ T_S found for undiluted networks arises in part from mutual orientation of segments by their neighbors. An additional cause comes from the anisotropy of the internal field arising from local order. All of these effects of the internal field arising from local order. All of these effects are interpretable in terms of relatively short-range interactions and do not require the relatively long-range ordering of a type proposed in some recent theories.     

Comparison between aesthetic and thermal performances of copper oxide and titanium dioxide nano-particulate coatings

Nano-particulate coatings with high reflectance against solar irradiation can control undesirable thermal heating by sunlight absorption. It can reduce the energy consumption for air conditioning of houses and cars. For the objects covered by these coatings and subjected to human sight, e.g. roofing surfaces, high dazzle of reflected visible light can offend the human eyes and spoil the fine view of covered objects. The authors introduced a new optimization method in designing pigmented coatings which considers both thermal and aesthetic effects in previous studies. The optimization is possible by controlling the material, size and concentration of pigment particles. The proposed coatings maximize the reflectance of near infrared (NIR) region to care the thermal effects and minimize the visible (VIS) reflected energy to keep the dark tone because of aesthetic appeal. Two different types of copper oxide pigment particles namely cupric oxide (CuO) and cuprous oxide (Cu₂O) were considered in this study. The optimum characteristics and performances are obtained and compared with titanium dioxide (TiO₂) particle as a typical cool pigment. The results show that cupric oxide has much better performance for our objective.     

Investigation of molecular dynamics in β-carotene using femtosecond pump-FWM spectroscopy

We have carried out two different pump four-wave mixing experiments, combining an initial pump excitation and a subsequent four-wave mixing probe process, on the photosynthetic pigment β-carotene to reveal different aspects of its molecular dynamics after photoexcitation. Firstly, the pump degenerate four-wave mixing (pump -DFWM) technique, in which the DFWM is resonant with the S₁- to S _n -transition of β-carotene, is used to monitor the events following excitation of the system. The transient shows a peculiar shape and is seen to depend on the energy of the initial pump pulse as well as on the concentration of the solute in the solvent. Secondly, pump coherent anti-Stokes Raman scattering (pump-CARS) is used to elucidate the excited state vibrational dynamics of β-carotene. This technique gives access to the dynamics of both ground and excited electronic states with vibrational selectivity.     

Advantages and limitations of OM, SEM, TEM and AFM in the study of ancient decorated pottery

This paper presents results from the study of two fragments of pre-Hispanic pottery, decorated with red pigment, using Optical Microscopy (OM), Scanning Electron Microscopy (SEM), High Resolution Transmission Electron Microscopy (HRTEM), Atomic Force Microscopy (AFM) and Magnetic Force Microscopy (MFM). Capabilities and limitations of these techniques in the analysis of archaeological material are highlighted with special emphasis on TEM, AFM and MFM due to their contribution in the study of the pigment layer at micro and nano scale. The analyzed samples come from the archaeological sites of El Tajin and Xochicalco, both in Mexico. Results of conventional TEM and HRTEM analysis of the red pigment showed nanometric Fe₂O₃ particles in both samples but different particle shape and size distributions: specimen from El Tajin presented irregular particles between 50–100 nm while that from Xochicalco exhibited semispherical shapes in the 3–25 nm range. AFM images showed the topography of the pigments, which are related to the texture of their surface and thus to the production process. Finally, MFM showed different contrast regions suggesting the presence of ferromagnetic elements forming clusters and domain orientations on the color layer.     

Probing temperature-sensitive behavior of pNIPAAm-coated iron oxide nanoparticles using frequency-dependent magnetic measurements

Ferromagnetic iron oxide nanoparticles of about 33 nm in diameter were synthesized by high-temperature decomposition of an iron-oleate complex, using octadecene as the solvent. These particles were subsequently coated with polyN-isopropylacrylamide (pNIPAAm) by a surfactant exchange method. Temperature-sensitive behavior of these particles was studied using ac susceptibility and dynamic light scattering (DLS) measurements. Shifts in the imaginary part of the ac susceptibility are correlated with swelling and collapse of pNIPAAm as a function of temperature.     

An optimised molecular model for ammonia

Based on molecular dynamics (MD) computer simulations we investigate the dynamic behaviour of a model complex fluid suspension consisting of large (A) particles (the ‘solute’) immersed in a bath of smaller ‘solvent’ (B) particles. The goal is to identify the effect of systematic simplifications (coarse-graining) of the solvent on typical microscopic time correlation functions characterizing the single-particle and collective dynamics of the solute. As a reference system we employ a binary Lennard–Jones mixture of spherical particles with significant differences in particle sizes (σ_A>σ_B) and masses (m _A>m _B). We then replace the original B particles step by step by a reduced number of larger and heavier particles such that the mass and volume fraction of B particles is kept constant. At each step of coarse-graining, the intermolecular interactions between A particles are chosen such that the static A–A structure of the reference system is preserved. Our MD results indicate that coarse-graining has a profound influence on both the single-particle dynamics as reflected by the self-diffusion constant and the collective dynamics represented by the distinct part of the van Hove time correlation function. The latter holds only at intermediate packing fractions, whereas the collective dynamics turns out to be essentially insensitive to coarse-graining at high packing fractions.     

Char characteristics and particulate matter formation during Chinese bituminous coal combustion

The characteristics of char particles and their effects on the emission of particulate matter (PM) from the combustion of a Chinese bituminous coal were studied in a laboratory-scale drop tube furnace. The raw coal was pulverized and divided into three sizes, <63, 63–100, and 100–200 μm. These coal samples were subjected to pyrolysis in N₂ and combusted in 20 and 50% O₂ at 1373, 1523, and 1673 K, respectively. Char samples were obtained by glass fiber filters with a pore size of 0.3 μm, and combustion-derived PM was size-segregated by a low pressure impactor (LPI) into different sizes ranging from 10.0 to 0.3 μm. The characteristics of char particles, including particle size distribution, surface area, pore size distribution, swelling behavior and morphology property, were studied. The results show that, coal particle size and pyrolysis temperature have significant influence on the char characteristics. The swelling ratios of char samples increase with temperature increasing from 1373 to 1523 K, then decrease when the temperature further increases to 1623 K. At the same temperature, the swelling ratios of the three size fractions are markedly different. The finer the particle size, the higher the swelling ratio. The decrease of swelling ratio at high temperature is mainly attributed to the high heating rate, but char fragmentation at high temperature may also account for the decrease of swelling ratio. The supermicron particles (1–10 μm) are primarily spherical, and most of them have smooth surfaces. Decreasing coal particle size and increasing the oxygen concentration lead to more supermicron-sized PM formation. The influence of combustion temperature on supermicron-sized PM emission greatly depends on the oxygen concentration.     

Depolarized light scattering from swollen-filled rubber

The H_v small-angle light-scattering patterns from cross-linked swollen rubbers containing glass bead filler particles are shown to arise from the birefringence patterns associated with the inhomogeneous swelling in the vicinity of the particles. Theoretically calculated patterns are obtained by using the stress field calculated by Sternstein and are found to agree with the experimental results.     

MRI study of Fickian, case II and anomalous diffusion of solvents into hydroxypropylmethylcellulose

Magnetic resonance imaging was used to investigate the diffusion and swelling processes of a hydroxypropylmethylcellulose (HPMC) matrix. Polymer in the form of a cylinder was hydrated in a water solvent with pH 2, 7, and 12 at 37 °C and monitored at equal intervals on a Bruker Avance 300 MHz spectrometer. The spatially resolved spin-spin relaxation times and spin densities together with the change in the dimension of the glass core of the polymer were determined for the HPMC tablets as a function of hydration times. FromT ₂ parameters, the solvent molecule mobility within the gel layer of the HPMC was estimated. All studied parameters allow the determination of the diffusion of the solvent into the HPMC matrix as Fickian diffusion for alkaline solvents, case II for acidic solvent, and anomalous diffusion for neutral solvent.     

The interaction of dislocation loop and γ' precipitate in nickel based alloys

The nucleation and growth of interstitial loops during irradiation has a : ontrolling effect on the subsequent swelling behaviour of metals. In nickel based alloys containing ordered γ' precipitate (Ni₃Al, Ti), interactions occur between the nucleated loops and γ' particles. This effect has been studied in two nickel based alloys using a High Voltage Electron Microscope.

For the case of Nimonic 80A alloy containing 18% volume fraction : gamma;' precipitate, dislocation loop-particle interactions obeyed the developed isotropic elasticity theory.²'³'¹² Consequently, rather low dislocation densities were developed and the swelling resistance was high during electron irradiation. In Nimonic 115A alloy, loop nucleation and growth was dependent on the availability of interfacial dislocation surrounding the γ' particles.

With regard to the swelling behaviour of γ' hardened alloys, it : s concluded that several mechanisms contribute to make these materials resistant.

Coherency strains at the γ' particles reduce the density of : limbing dislocations.

The γ' precipitate affects the climb efficiency of the : ucleated dislocations by:

pinning the dislocation line, thus introducing a line tension force : hich opposes dislocation climb and reduces swelling;

reducing the available volume of material in which dislocation loops : an nucleate and grow.