聚对苯二甲酸丁二醇酯/聚(对苯二甲酸丁二醇酯-e-己内酯)二元结晶共混体系的相容性和结晶行为

聚对苯二甲酸丁二醇酯(PBT)/聚(对苯二甲酸丁二醇酯-e-己内酯)(PBT-PCl)是一个新制备的具有分子间排斥相互作用的A/AxB1?x型两元结晶共混体系. 根据两元平均场模型,报道对苯二甲酸丁二醇酯(BT)与"-己内酯(CL)结构单元的相互作用参数为0.305. DSC研究发现,此共混物呈现了与典型的共聚物/均聚物共混物不同的结晶特征. PBT-PCL影响PBT链的活动力和晶片堆积;同时PBT-PCL的结晶受到先期结晶的PBT晶粒的阻滞. 尽管拥有相同的BT单元,共混的两组分在组成变化范围内仍没有形     

Rheological,thermal, and mechanical properties of poly(ethylene naphthalate)/poly(ethylene terephthalate) blends

Structural, Theological, thermal, and mechanical properties of blends of poly(ethylene naphthalate) (PEN) and poly(ethylene terephthalate) (PET) obtained by melt blending were investigated using capillary rheometry, differential scanning calorimetry (DSC), scanning electron microscopic (SEM) observation, tensile testing. X-ray diffraction, and ¹H nuclear magnetic resonance (NMR) measurements. The melt Theological behavior of the PEN/PET blends was very similar to that of the two parent polymers. The melt viscosity of the blends was between that of PEN and that of PET. Thermal properties and NMR measurement of the blends revealed that PEN is partially miscible with PET in the as molded blends, indicating that an interchange reaction occurs to some extent on melt processing. The blend of 50/50 PEN/PET was more difficult to crystallize compared with blends of other PEN/PET ratios. The blends, once melted during DSC measurements, almost never showed cold crystallization and subsequent melting and definitely exhibited a single glass transition temperature between those of PEN and PET during a reheating run. Improvement of the miscibility between PEN and PET with melting is mostly due to an increase in transesterification. The tensile modulus of the PEN/PET blend strands had a low value, reflecting amorphous structures of the blends, while tensile strength at the yield point increased linearly with increasing PEN content.     

Synthesis of Poly(butylene terephthalate)/Attapulgite Nanocomposites by In-Situ Polymerization and Its Crystallization Behavior

Poly(butylene terephthalate) (PBT)/attapulgite (AT) nanocomposites were prepared via in-situ polymerization without pre-modification of AT. By this method, PBT chains were successfully grafted onto the surface of AT, which was confirmed by Fourier transform infrared spectroscopy and thermogravimetric analysis. Scanning electron microscope examination indicated the uniform dispersion of AT nanoparticles in PBT matrix. The crystallization behavior of PBT/AT nanocomposites was investigated by X-ray diffraction patterns, differential scanning calorimetry, and step-scan differential scanning calorimetry. The non-isothermal crystallization processes were analyzed with the Avrami, Ozawa, and Mo methods. Crystallization activation energies of the samples were also determined by the Kissinger method. The results indicated that AT could act as a heterogeneous nucleating agent in PBT crystallization and lead to an acceleration of crystallization, while AT also acted as a physical hindrance to retard the transport of polymer chains to the growing crystals.     

Manufacture and Characterization of Poly (butylene terephthalate) Nanofibers by Electrospinning

Poly (butylene terephthalate) (PBT) nanofiber mats were prepared by electrospinning, being directly deposited in the form of a random fibers web. The effect of changing processing parameters such as solution concentration and electrospinning voltage on the morphology of the electrospun PBT nanofibers was investigated with scanning electron microscopy (SEM). The electrospun fibers diameter increased with rising concentration and decreased by increasing the electrospinning voltage, thermal and mechanical properties of electrospun fibers were characterized by DSC and tensile testing, respectively.     

Morphology of ternary immiscible polymer blends

Ternary blends consisting of thermoplastic and thermotropic immiscible polymers were studied. Both thermodynamic and kinetic considerations were found to affect their multiphase structure. Thermodynamics is expressed by means of spreading coefficients, whereas the kinetic effect is driven by the dispersed phase viscosity ratio. Some morphologies could be predicted, when both effects acted cooperatively. However, in cases where the effects were opposing, kinetics hindered the development of the expected structure; interpenetration between the two minor phases, rather than engulfing or separately dispersed morphology, took place. In cases where two relatively polar phases were dispersed in a nonpolar matrix (e.g., nylon and polycarbonate in polypropylene), the interaction between the two dispersed minor phases always existed due to their low interfacial tension. Spreading of one minor phase over another, rather than penetration, is the dominating mechanism of encapsulation in polymer blends, contrary to low molecular weight liquids where both spreading and penetration play an important role in the structurization.     

Isothermal Melt Crystallization Kinetics for Poly(Trimethylene Terephthalate)/Poly(Butylene Terephthalate) Blends

The kinetics of isothermal melt crystallization of poly(trimethylene terephthalate) (PTT)/poly(butylene terephthalate) (PBT) blends were investigated using differential scanning calorimetry (DSC) over the crystallization temperature range of 184–192°C. Analysis of the data was carried out based on the Avrami equation. The values of the exponent found for all samples were between 2.0 and 3.0. The results indicated that the crystallization process tends to be two‐dimensional growth, which was consistent with the result of polarizing light microscopy (PLM). The activation energies were also determined by the Arrhenius equation for isothermal crystallization. The values of ΔE of PTT/PBT blends were greater than those for PTT and PBT. Lastly, using values of transport parameters common to many polymers (U*=6280 J/mol, T _∞=T _g – 30), together with experimentally determined values of T _m ⁰ and T _g, the nucleation parameter, K _g, for PTT, PBT, and PTT/PBT blends was estimated based on the Lauritzen–Hoffman theory.     

Nanofilled Polypropylene/Poly(trimethylene terephthalate) Blends: A Morphological and Mechanical Properties Study

Polypropylene (PP) /poly(trimethylene terephthalate), (PTT), binary blends in the presence of two interfacial modifier as well as two organically modified nanoclay additives were studied in terms of mechanical and morphological characteristics. Scanning electron microscopy confirmed the incompatibility of the system which was solved to some extent through incorporating the nanoclay as well as functional compatibilizers. An evaluation of the specimens via static mechanical tests in tensile mode gave credence to the assumption that the higher the PTT content, the higher the mechanical performance would be. Furthermore, the compatibilizer-containing blends not only exhibited higher toughness, but also possessed enhanced stiffness when a maleated compatibilizer was added. The tensile modulus was promoted further in the presence of clay nanoparticles; however, toughness was somewhat sacrificed. The Barentsen as well as Halpin-Tsai models were found to describe the binary blends modulus. The reinforcing impact of the nanoclay was exploited to a greater degree in the presence of the compatibilizer.     

Fiber Structure,Tensile Behavior and Antibacterial Activity of Polylactide/Poly(butylene terephthalate) Bicomponent Fibers Produced by High-Speed Melt-Spinning

Abstract

Various types of bicomponent fibers composed of polylactide (PLA) and poly(butylene terephthalate) (PBT) with different molecular weights, arranging the polymers separately in the skin or core, were produced by high-speed melt-spinning. The bicomponent spinning, arranging the PLA with high molecular weight (melt flow rate =1.9?g/10?min, L-lactide content = 98.7%) in the skin and the PBT with low molecular weight (IV = 0.835–0.865 dL/g) in the core, resulted in orientation-induced crystallization in the PLA component at the spinning speed of 2?km/min. This crystallization effect was ascribed to a chain-extending treatment applied to the original PLA (MFR = 4.0?g/10?min) to increase its molecular weight. By the treatment the PLA could crystallize when spun even at 1?km/min in its single-component spinning. On the other hand, the bicomponent spinning system interfered with the orientation-induced crystallization of PBT in the core. As a result, the critical spinning speed needed to generate the orientation-induced crystallization in the core PBT was elevated to 4?km/min. The inferior tensile behavior of the bicomponent fibers, as compared to the single-component PLA or PBT fibers, suggested poor compatibility between PLA and PBT. Transesterification reactions rarely occurred at the interface of the two polymers. The bicomponent fibers prepared from high molecular weight PLA and low molecular weight PBT, however, showed sufficient antibacterial activity and physical properties to be suitable for designing medical clothing materials.     

Fabrication and Physical Characterization of Biodegradable Poly(butylene succinate)/Carbon Nanofiber Nanocomposite Foams

Nanocomposites of biodegradable poly(butylene succinate) (PBS) and carbon nanofibers (CNFs) were prepared by three different methods, that is, solution blending, melt compounding, and solution and subsequent melt blending (SOAM) method, among which the SOAM method, where nano-scale fillers and polymer matrix are solution-blended and subsequently melt-mixed in a torque rheometer, is a two-step process for obtaining polymer nanocomposite. Dispersion of CNFs in the PBS matrix was characterized by FE-SEM, while thermal and mechanical properties were analyzed by thermogravimetric ananlysis (TGA) and universal test machine (UTM), respectively. The PBS/CNF nanocomposites were then converted to foams by employing a chemical blowing agent (CBA) in the melt. The presence of CNFs increased the melt viscosity of PBS so that the PBS/CNF nanocomposite foams were produced without modifying the chemical structure of the PBS. Nanocomposite foams prepared by the SOAM method showed higher physical properties compared with those prepared by the solution blending and the melt mixing. Cell size and blowing ratio increased with the increase in the CBA content, blowing temperature and time. Cell morphology of the nanocomposite foams was examined by optical microscopy, and the cell size distribution was also investigated.     

Upgrading poly(butylene succinate)/wood fiber composites by esterified lignin

Aliphatic chains were introduced into the macromolecule of kraft lignin using aliphatic chlorides as esterification reagents. The hydrophobicity of esterified lignin (EL) was enhanced as compared to the original lignin. EL was further used as a macromolecular coupling agent in poly(butylene succinate)/chemi-thermomechanical pulp fiber composites. As a result, the composites with enhanced mechanical performance were obtained, and the tensile strength, impact strength, and bending strength were increased by 25.1, 22.4, and 19.3%, respectively, under 2 wt% EL-treatment (synthesized by palmitoyl chloride, –COCl/–OH = 1.5:1) in comparison with those of the specimen without any coupling agent treatment. Furthermore, the composite prepared with EL-treated fibers shows significant lower water absorption ratio than that of untreated one. A significant increase in storage modulus (E′) was observed upon the incorporation of treated fibers. Furthermore, the improved interfacial bonding between treated fibers and matrix was verified by SEM images. The shear viscosity of composite was increased by the incorporation of EL, but in general, the rheological behaviors of composites are not significantly changed.     

Miscibility,Morphology, and Thermal Properties of Poly(Trimethylene Terephthalate)/Polycarbonate

Abstract

Poly(trimethylene terephthalate)/polycarbonate (PTT/PC) blends were prepared by melt blending and rapid quenching in ice water. The miscibility and thermal properties were investigated using differential scanning calorimeter (DSC) and dynamic mechanical analysis (DMA). The blend's morphologies were investigated using scanning and transmission electron microscopies. Both DSC and DMA results suggested that PTT and PC were very limited, partially miscible pairs. The melting point, melt crystallization, and cold crystallization exotherms in the blends of PTT were depressed by the presence and amount of PC. When the PC content was <50 wt%, PC spherical particles were found to distribute evenly in the PTT matrix; at 50–60 wt%, the two‐phase structures were close to being bicontinuous. At higher PC content, PTT formed a string‐like texture in the PC matrix. The PTT spherulitic morphologies in PTT/PC blends were found to be very sensitive to PC and PC content. When the PC content was ≥60 wt%, the blends crystallized as an agglomeration of tiny PTT crystals.     

Non-Isothermal Crystallization Kinetics of Poly(Butylene Terephthalate)/Silica Nanocomposites

Poly(butylene terephthalate)/silica nanocomposites were prepared by in situ polymerization of terephthalic acid, 1,4-butanediol and silica. Transmission electron microscopy (TEM) was used to examine the quality of the dispersion of silica in the PBT matrix. The non-isothermal crystallization behavior of pure PBT and its nanocomposites was studied by differential scanning calorimetry (DSC). The results show that the crystallization peak temperatures of PBT/silica nanocomposites are higher than that of pure PBT at a given cooling rate. The values of halftime of crystallization indicate that silica could act as a heterogeneous nucleating agent in PBT crystallization and lead to an acceleration of crystallization. The non-isothermal crystallization data were analyzed with the Avrami, Ozawa, and Mo et al. models. The non-isothermal crystallization process of pure PBT and PBT/silica nanocomposites can be best described by the model developed by Mo et al. According to the Kissinger equation, the activation energies were found to be ?217.1, ?226.4, ?259.2, and ?260.2 kJ/mol for pure PBT and PBT/silica nanocomposites with silica weight content of 1, 3 and 5 wt%, respectively.     

Effects of Montmorillonite on the Nonisothermal Crystallization Behavior of the Poly(trimethylene terephthalate)/Polypropylene/Montmorillonite Nanocomposites

Organic montmorillonite (MMT) reinforced poly(trimethylene terephthalate) (PTT)/ polypropylene (PP) nanocomposites were prepared by melt blending. The effects of MMT on the nonisothermal crystallization of the matrix polymers were investigated using differential scanning colorimetry (DSC) and analyzed by the Avrami equation. The DSC results indicated that the effects of MMT on the crystallization processes of the two polymers exhibited great disparity. The PTT's crystallization was accelerated significantly by MMT no matter whether PTT was the continuous phase or not, but the thermal nucleation mode and three-dimensional growth mechanism remained unchanged. However, in the presence of MMT, the PP's crystallization was slightly retarded with PP as the dispersed phase, and was influenced little with PTT as the dispersed phase. When the MMT content was increased from 2_wt% to 7_wt%, the crystallization of the PTT phase was slightly accelerated, whereas the crystallization of the PP phase was severely retarded, especially at lower temperatures. Moreover, the nucleation mechanism for the PP's crystallization changed from a thermal mode to an athermal one. In the polypropylene-graft-maleic anhydride (PP-g-MAH) compatibilized PTT/PP blends, with the addition of 2_wt% MMT during melt blending, the T _c (PTT) shifted 7.8°C to lower temperature and had a broadened exotherm, whereas the T _c (PP) shifted 17.1°C to higher temperature, with a narrowed exotherm. TEM analysis confirmed that part of the PP-g-MAH was combined with MMT during blending.     

Reactive Compatibilization of Poly(Butylene Terephthalate)/Acrylonitrile-Styrene-Acrylate Blends by Epoxy Resin: Morphology and Mechanical Properties

The effect on the notched Izod impact strength of poly(butylene terephthalate) (PBT) by blending it with acrylonitrile-styrene-acrylate (ASA) was examined. Epoxy resin (ER) was demonstrated to be an efficient compatibilizer for the partially compatible blends of PBT/ASA. It requires only a very small amount of ER to improve the toughness of the PBT/ASA blends drastically. Furthermore, there exists an optimum proportion of ER added to achieve maximum notched Izod impact strength. Transmission electron microscopy (TEM) observation suggests that the ER in the PBT/ASA/ER blends suppressing the tendency of coalescence of ASA, leading to better dispersion of the ASA particles. Field emission scanning electron microscopy (FESEM) shows that ER enhances the phase dispersion and the interfacial adhesion between the PBT and ASA phases, it improves the compatibility between PBT and ASA. The compositions in the interphase was continuous, which results in multiphase composites with a graded interphase. It is suggested that enhanced interphase adhesion was necessary to obtain improved dispersion, fine phase morphology, and better toughness.     

Synergistic Effect of Polycarbonate on Reactive Core-Shell Particles Toughened Poly(Butylene Terephthalate)

Glycidyl methacrylate functionalized methyl methacrylate-butadiene-styrene copolymer (MBS-g-GMA) core-shell particles were prepared via an emulsion polymerization process. MBS-g-GMA was used to toughen poly(butylene terephthalate) (PBT) and the synergistic toughening effect of polycarbonate (PC) on PBT/MBS-g-GMA blends were investigated. Notched impact tests showed the percolation threshold became lower with the increase of PC content. Transmission electron microscopy displayed a very good dispersion of MBS-g-GMA particles in the PBT matrix with the different PC contents. The synergistic toughening effect was due to the encapsulation structure of PC which could facilitate the whole PBT matrix to yield. The more perfect the encapsulation structure formed, the more obvious the synergistic toughening the PC achieved. Sufficient strength of the phase interface was important to ensure the stress transfer effectively and facilitate the whole PBT matrix to yield. The interface strength between PC and MBS-g-GMA could be ensured by the good miscibility between Poly(methyl methacrylate) (PMMA) (grafted onto the polybutadiene-based rubber core) and PC. For the PBT/PC, the transesterification between PBT and PC improved the interface strength of the PBT and PC phases, as demonstrated by Fourier transform infrared spectroscopy (FTIR) scans. Scanning electron microscopy results showed shear yielding of the matrix and cavitation of the rubber particles were the major toughening mechanisms.     

Effect of PMMA on crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate) blend prepared in semi-dilute solutions

Films of poly(vinylidene fluoride) (PVDF)/poly(methyl methacrylate) (PMMA) blend were derived from a special procedure of casting semi-dilute solutions. Hydrophilic character and crystallization of PVDF were optimized by variation of PMMA concentration in PVDF/PMMA blends. It was found that a PVDF/PMMA blend containing 70 wt% PMMA has a good performance for the potential application of hydrophilic membranes via thermally induced phase separation. The films presented β crystalline phase regardless of PMMA content existed in the blends. Thermal analysis of the blends showed a promotion of crystallization of PVDF with small addition of PMMA which induced larger lamellar thickness of PVDF, leading to the largest spherulitic crystal of PVDF (10 wt% PMMA) is about 8 μm. SEM micrographs illustrated no phase separation occurred in blends, due to the high compatibility between PVDF and PMMA.     

Preparation and Properties of Poly(ethylene terephthalate)/Silica Nanocomposites

A kind of poly(ethylene terephthalate) (PET)/Silica nanocomposite (PETS) was synthesized via in situ polymerization using the compatibility between silica nanoparticles and ethylene glycol (EG). Transmission electron microscopy (TEM) micrographs revealed that the silica nanoparticles were well dispersed in the PET matrix, the particle size was about 10 nm with narrow distribution, and there existed strong interaction between the particles and the polymer chains. Differential scanning calorimetry (DSC) results indicated that the thermal properties of PETS with 2 wt% silica (PETS‐2) are different from those of pure PET (PETS‐0). The properties of the as‐spun fibers show that the tenacity and LASE‐5 (load at a specified elongation of 5%) of PETS‐2 were higher than those of PETS‐0, while the heat shrinkage of PETS‐2 was lower than that of PETS‐0. We suggest that the increasing of crystallinity and the strong interface interaction of the nanocomposite caused the fibers of PETS‐2 to not only have higher tenacity and LASE‐5 but also to have lower heat shrinkage.     

Poly(Butylene Terephthalate)/Single Wall Carbon Nanotubes Composite Nanofibers by Electrospinning

Poly(buthylene terephthalate)(PBT)/single wall carbon nanotubes (SWCNTs) composite nanofibers were prepared by electrospinning. The effect of carbon nanotubes on the morphology, crystallization, and mechanical properties of the electrospun composite nanofibers were investigated by SEM, DSC, and tensile testing, respectively. SEM observations indicated that the presence of SWCNTs resulted in finer nanofibers for lower loading; however, a broader distribution, especially for the higher diameter ranges was found for nanofibers with higher amounts of carbon nanotubes. SWCNTs accelerated crystallization and acted as a nucleating agent; the degree of crystallinity increased with increasing content of SWCNTs, followed by a moderate decrease at higher content. Specific tensile strength and modulus of the PBT/SWCNTs composite nanofibers mats were higher than that of neat PBT nanofibers mat. However, the elongation at break of composite nanofibers mats was lower than that of the neat PBT nanofibers mat.     

Microstructures and Mechanical Properties of Poly(Trimethylene Terephthalate)/Maleic Anhydride Grafted Poly(Ethylene-octene)/Polypropylene Blends

A range of blends based on 70 wt% of poly(trimethylene terephthalate) PTT with 30 wt% dispersed phase were produced via melt blending. The dispersed phase composition was varied from pure maleic anhydride grafted poly(ethylene-octene) (POE-g-MA) over a range of POE-g-MA:polypropylene (PP) ratios. The micromorphology and mechanical properties of the ternary blends were investigated. The results indicated that the domains of the POE-g-MA are dispersed in the PTT matrix, and at the same time the POE-g-MA encapsulate the PP domains. The interfacial reaction between the hydroxyl-end group of PTT and maleic anhydride (MA) during melt blending changes the formation from “isolated formation” to “capsule formation,” where the PP domains are encapsulated by POE-g-MA. Compared to the PTT/POE-g-MA blends, mechanical properties of ternary blends, such as tensile strength and Young's modulus, were improved significantly.     

Preparation and Properties of Antimicrobial Poly(butylene adipate-co-terephthalate)/TiO2 Nanocomposites Films

Abstract

Poly(butylene adipate-co-terephthalate) (PBAT) nanocomposite films with various contents of nano-titanium dioxide (TiO₂) and titanium dioxide doped silver (Ag-TiO₂) were prepared by a solvent casting method. The TiO₂ and Ag-TiO₂ nanoparticles were surface-modified with silane coupling agents to improve their compatibility and dispersibility in the PBAT matrix. They were denoted as mTiO₂ and mAg-TiO₂, and were characrterized by Fourier transform infrared (FTIR) spectroscopy and transmission electron microscopy (TEM). The morphology of the PBAT nanocomposite films was studied by field emission scanning electron microscopy (FE-SEM). The crystallinity of the PBAT film increased upon the introduction of the nano-TiO₂/Ag-TiO₂. Its mechanical properties and gas barrier properties were also significantly improved. In addition, the PBAT/mTiO₂ and PBAT/mAg-TiO₂ nanocomposite films showed a strong antibacterial activity against Gram-negative (Escherichia coli) and Gram-positive (Staphylococcus aureus) food-borne pathogenic bacteria.