Preferential surface segregation of homopolymer and copolymer blend films

Surface film properties of the homopolymers polystyrene (PS), poly(methyl methacrylate) (PMMA), poly(butyl methacrylate) (PBMA) and the copolymer poly(methyl methacrylate)-co-poly(butyl methacrylate) (PMMA-co-PBMA) and their blends with PS have been examined by atomic force microscopy (AFM) and contact angle measurements. The total and the Lifshitz-van der Waals, acid and base components of the surface free energy together with the work of adhesion and its components, the cohesive energy density and the solubility parameters of the homopolymer, copolymer and blend films were determined. Films of about 3 μm were considered. The results are discussed in terms of surface migration mechanisms based on surface free energy and solubilities of the polymers in the solvent, toluene in this paper. AFM imaging and contact angles revealed surface enrichment at the air polymer interface of PBMA for both the PS/PBMA blend and the copolymer PMMA-co-PBMA, whereas the PS/PMMA and PS/PMMA-co-PBMA blend film surfaces show island-like phase-separated structure of typical size 27.4-86.5 nm in diameter and 6.9-15.6 nm in height for PS/PMMA, while for PS/ PMMA-co-PBMA film surface the typical size is 49.6-153.3 nm in diameter and 1.6-14.2 nm in height.     

Monte carlo studies of phase transitions in polymer blends and block copolymer melts

Summary The unmixing transition of both symmetrical polymer blends AB (i.e. chain lengthsN _A=N _B=N) and asymmetrical ones (N _B/N _A=2,3) is studied by large-scale Monte Carlo simulations of the bond fluctuation model. Combination of semi-grand-canonical simulation techniques, ?histogram reweighting? and finitesize scaling allows an accurate location of the coexistence curve in the critical region. The variation of the critical temperature with chain length (N) is studied and compared to theoretical predictions. For the symmetrical case, use of chain lengths up toN=512 allows a rough estimation of crossover scaling functions for the crossover from Ising to mean-field exponents. The order-disorder transitions in melts of both symmetric (compositionf=N _A/(N _A+N _B)=1/2) and asymmetric (f=3/4) block copolymers is studied for very short chains (16≤N≤60). The interplay between structure and chain configuration is emphasized. Qualitative evidence for ?dumbell formation? of chains and vacancy enrichment in A-B-interfaces and near hard walls is presented. Paper presented at the I International Conference on Scaling Concepts and Complex Fluids, Copanello, Italy, July 4–8, 1994.     

Adhesion enhancement in polystyrene/polyethylene blends by corona treatment and triblock copolymer addition

A comparative study of interfacial effects due to styrene-butadiene-based triblock copolymer (SEBS) addition and to corona treatment has been investigated for blends of polyethylene (PE) and polystyrene (PS). Blends of PS/PE covering a wide range of weight composition have been prepared in the molten state. Scanning electron microscopy demonstrated that moderate amounts of SEBS copolymer addition (2-5%) resulted in finer particle dispersion and in better interfacial adhesion between PE and PS phases. Tensile strength and elongation at break were also significantly improved. In the case of corona treatment of both polyethylene and polystyrene, the tensile strength of the blends increased while their elongation at break remained almost unchanged. The same trend was found when small amounts of corona-treated blend (5%) were added to the non-modified PS/PE blends. Rheological measurements revealed that corona treatment resulted in a decrease of dynamic shear viscosity of both PE and PS. From a view-point of morphological and mechanical properties, the triblock copolymer was found to be the more efficient modifier. Nevertheless, much higher tensile strengths, but lower elongations at break were obtained when the blends were modified by corona-treated SEBS copolymer. The results suggest that a combination of the two modification methods may be a promising route to enhance performance properties in the immiscible PS/PE system.     

AB/CD嵌段共聚物共混体系多尺度结构的自洽场模拟

本文采用自洽场理论模拟了AB/CD嵌段共聚物共混体系的自组装. 改变组分B与D间的相互作用, 得到了不同空间尺度上的两种层状结构和只能在非对称组成情况才能得到的核壳结构. 结果表明, 这种多尺度结构的形成是因为BD间排斥作用的减弱或者吸引 作用的增强导致二者间相互融合程度的增加. 当BD间的相互融合程度与AB和CD间的相互融合程度相当时, 体系会发生宏观层状与微观层状结构间的转变. 此外, 本文还从能量角度揭示了体系发生这种结构转变的深层次原因. 关键词： 嵌段共聚物 共混 多尺度结构 自洽场     

Synthesis and conformational characterization of functional di-block copolymer brushes for microarray technology

Surface initiated polymerization (SIP) coupled with reversible addition-fragmentation chain transfer polymerization (RAFT) was used to functionalize microarray glass slides with block polymer brushes. N,N-dimethylacrylamide (DMA) and N-acryloyloxysuccinimide (NAS) (graft-poly[DMA-b-(DMA-co-NAS)]) brushes, with di-block architecture, were prepared from a novel RAFT chain transfer agent bearing a silanating moiety (RAFT silane) directly anchored onto the glass surfaces. Conformational characterization of the coatings was performed by Self Spectral Interference Fluorescence Microscopy (SSFM), an innovative technique that describes the location of a fluorescent DNA molecule relative to a surface with sub-nanometer accuracy. X-ray Photoelectron Spectroscopy (XPS) and Scanning Electron Microscopy (SEM) were used to characterize the coatings composition and morphology.     

Study of structural,morphological and mechanical properties of PMMA,PVC and their blends

PMMA, PVC and their five blends in different compositions were irradiated by γ -rays of 2 Mrad dose. A comparative study of structural, morphological and mechanical properties of irradiated and non-irradiated samples was carried out. The structural changes that have taken place due to irradiation are seen in the FTIR and X-ray diffraction (XRD) spectra. The ester group is mainly affected in PMMA and the blends. The XRD results have confirmed that the irradiated samples are more amorphous in nature than the non-irradiated ones. The DSC study reveals that some irradiated samples undergo cross-linking, whereas some of them undergo degradation. One of the irradiated blend compositions has become thermally more stable. The SEM study suggests that the irradiated samples have undergone curing. An improvement in the mechanical properties has been observed in some of the irradiated blend compositions.     

Infrared studies on the molecular interactions of polymer blends: polystyrenes and polycarbonates systems

Fourier—transform infrared (FT-IR) with digital subtraction method has been applied to investigate the molecular interactions of immiscible polystyrene (PS)/bisphenol A polycarbonate (PC) blends and miscible PS/tetra-methyl PC (TMPC) blends. The FT-IR results show that there are no interactions for PS/PC, and the miscibility of PS/TMPC blends is mainly due to the intermolecular interaction between the phenyl ring of PS and the carbonate group of TMPC. The phenyl ring band of PS is linearly shifted to higher wave number with increasing concentration of TMPC, and the bandwidth at half maximum intensity of the carbonyl band of TMPC is linearly decreased with increasing concentration of PS. The amplitude of the interactional bands is decreased with increasing temperature consistent with LCST behavior of the blend. The miscibility of PS/TMPC and immiscibility of PS/PC has also been discussed in terms of local free-volume, self-interactions, and intermolecular interactions based on the chemical structures of PC and TMPC. Furthermore, the immiscibility behavior for blends of methyl-substituted PS and TMPC, and blends of PS and halogen-substituted PC has been explained in terms of intra and intermolecular interactions caused by steric and/or induction effects.     

Mesostructures and properties of transparent block copolymer/silica nanocomposite monoliths

In this work, three different block copolymer/silica hybrid nanocomposite monoliths that possess mesostructured domains (hexagonal, cubic, and disordered) were prepared through the micellization of the block copolymer during the sol-gel process of a silica precursor. Transparent block copolymer/silica nanocomposite monoliths were obtained from the amphiphilic triblock copolymer poly(ethylene oxide)-b-poly(propylene oxide)-b-poly(ethylene oxide) (EO₁₀₆PO₇₀EO₁₀₆, Pluronic F127), which we used to organize the polymerizing silica networks; the ratio between the block copolymer and silica was fixed at 60:40 (wt%). Small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM) were used to observe the mesostructural ordering. Temperature-dependent SAXS patterns of the cubic structured nanocomposites showed that the calcination process takes place at 210°C. The transmittances of the nanocomposite monoliths over the range of wavelengths from 400 to 800 nm was >85%. From rheological measurements at low frequency, it was found that the hexagonally structured monoliths had higher storage and loss moduli relative to the monoliths possessing cubic and disordered structures.     

Morphology,miscibility and mechanical properties of PMMA/PC blends

This study deals with some results on morphology, miscibility and mechanical properties for polymethyl methacrylate/polycarbonate (PMMA/PC) polymer blends prepared by solution casting method at different concentration between 0 and 100 wt%. Dynamic storage modulus and tan δ were measured in a temperature range from 30 to 180°C using dynamical mechanical analyzer (DMA). The value of the storage modulus was found to increase with the addition of the PC in the matrix. Transition temperature of pure PMMA and pure PC is found to be 83.8 and 150°C, respectively. The result shows that the two polymers are miscible for whole concentration of PC in PMMA. The distribution of the phases in the blends was studied through scanning electron microscopy (SEM). Also the mechanical properties like elongation at break and fracture energy of the PMMA/PC blends increase with the increase in concentration of PC in PMMA.     

Surface and interfacial properties of PVDF/acrylic copolymer blends before and after UV exposure

Morphological and chemical properties of both the surface and interface of poly(vinylidene fluoride)/poly(methyl methacrylate)-co-poly(ethyl acrylate) (PVDF/PMMA-co-PEA) blend films have been investigated before and after the samples were exposed to ultraviolet (UV) irradiation using a xenon arc lamp at 50 °C and 9% relative humidity (RH) for 7 months. Surface and interfacial morphologies were studied by atomic force microscopy (AFM). Chemical composition information was obtained by confocal Raman microscopy, attenuated total reflection-FTIR spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), and contact angle measurements. Results show an enrichment of the PVDF material at the air surface, while the acrylic copolymer enriches the interface. Blends having greater than 50% mass fraction of PVDF show little change in the surface morphology after UV exposure for 7 months. However, for a lower PVDF content, blends exhibit significant degradation of PMMA-co-PEA copolymer and a much rougher surface after UV exposure. Microstructural changes in the PVDF spherulites are also observed after UV degradation. It is found that the surface and interfacial morphologies are correlated with the chemical properties.     

Thermal and mechanical properties of gamma-irradiated prevulcanized natural rubber latex/low nitrosamines latex blends

Thermal and mechanical properties of blended radiation prevulcanized natural rubber latex (RVNRL) and low nitrosamines latex (LNL) were studied. RVNRL was blended with LNL at various composition ratios. From the tensile test, it was found that the optimum tensile value was attained at a total blending ratio of 70% RVNRL and 30% LNL. Latex blending with optimum tensile strength was then subjected to gamma irradiation at various doses with the presence and absence of methyl methacrylate (MMA) at 10?pphr. It was found that the gamma irradiation of latex blend with the presence of MMA could help increase further the tensile value. Composition of blending at a specific ratio and gamma irradiation at a specific dose has led to a significant improvement in the mechanical properties of the latex blend. The formation of grafting in the latex blend was characterized by Fourier transform infrared spectra (FTIR) spectroscopy and differential scanning calorimetry (DSC). FTIR spectroscopy confirmed that MMA could be grafted onto blended latex effectively under appropriate irradiation conditions. Two new peaks at 1731 and 1149?cm^?1 were observed after irradiation, indicating the presence of an ester group from poly(methyl methacrylate) (PMMA), which was grafted onto rubber chains. This finding was proved by the presence of new T_g in DSC analysis. The increase in new T_g indicates the movement of grafting chains, which are tightly bound onto rubber chains.     

Comparison of optical properties and mechanical/electrical degradation of some low density polyethylene-and polypropylene-based polymer blends

In this study, the optical properties as well as mechanical and electrical degradation of low-density polyethylene (LDPE)/polypropylene fiber (PP fiber) (10–50% PP fiber), polypropylene (PP)/PP fiber (10–50% PP fiber), and LDPE/diamond (0.1–3% diamond) blends, which are prepared by hot pressing method, with changing thicknesses ranging from 30 to 225 μm, are compared. The spectra, in the wavelength range 200–2500 nm, are examined. Based on optical absorption spectra obtained, Tauc graphs are plotted. Determined values of the direct optical energy gap (E _d ^opt ), the indirect optical energy gap (E _i ^opt ), the width of the band (ΔE), and ultraviolet transmittance (T_UV) are listed. The direct E _d ^opt and indirect E _i ^opt values for organic blends are in the range of 3.10–3.17 eV and 1.52–2.99 eV; for inorganic blends they are 1.80–4.13 eV and 1.55–4.7 eV respectively. The electrical strength (ε) and the mechanical tension (σ) have been investigated, and graphs (the dependence of the electrical life time log τ_ε on ε) are given. The experimental results are analyzed from the viewpoint of the validity of the thermofluctuation theory. LDPE and LDPE/0.5% diamond composite parameters consecutively changed: σ from 68 to 82 MPa, ε from 60·10⁶ to 85·10⁶ V/m, mechanical lifetime τ_σ from 10 to 1.5·10⁵ sec, electrical lifetime τ_ε from 2· 10³ to 2·10⁵ sec, and structure-sensitive parameters γ and χ — from 1.48 to 1.18 (J)MPa/mole and from 0.97 to 0.70 (J)Vm⁻¹/mole respectively. The values of mechanical and electrical durability were observed to increase by 20 and 41%, respectively, for LDPE/0.5% diamond composite. Published in Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 5, pp. 677–683, September–October, 2007.     

Synthesis and Raman spectroscopic study of Mg/Al,Fe hydrotalcites with variable cationic ratios

Hydrotalcites of formula Mg₆(Al,Fe)₂(OH)₁₆(CO₃)·4H₂O formed by intercalation with the carbonate anion as a function of divalent/trivalent cationic ratio have been successfully synthesised. The XRD patterns show variation in the d‐spacing attributed to the size of the cation. Raman and infrared bands in the OH stretching region are assigned to (1) brucite layer OH stretching vibrations, (2) water stretching bands and (3) water strongly hydrogen bonded to the carbonate anion. Multiple (CO₃)²⁻ symmetric stretching bands suggest that different types of (CO₃)²⁻ exist in the hydrotalcite interlayer. Increasing the cation ratio (Mg/Al,Fe) resulted in an increase in the combined intensity of the two Raman bands at around 3600 cm⁻¹, attributed to Mg OH stretching modes, and a shift of the overall band profile to higher wavenumbers. These observations are believed to be a result of the increase in magnesium in the structure. Raman spectroscopy shows a reduction in the symmetry of the carbonate, leading to the conclusion that the anions are bonded to the brucite‐like hydroxyl surface and to the water in the interlayer. Water bending modes are identified in the infrared spectra at positions greater than 1630 cm⁻¹, indicating that water is strongly hydrogen bonded to both interlayer anions and the brucite‐like surface. Copyright © 2009 John Wiley & Sons, Ltd.     

High-pressure conductivity studies of blends of poly(p-phenylene)s with oxyethylene side-chains and lithium salts

High-pressure electrical conductivity studies have been carried out with poly(p-phenylene)s with oxyethylene side-chains (PPP(EO)_x/y), which were blended with LiCF₃SO₃. Measurements were performed at pressures up to 280 MPa and at different temperatures. The influences of salt concentration, side-chain length, temperature, and plasticizer content on the relative conductance and activation volume are investigated. The temperature-dependent conductivity of the sample is non-Arrhenius and exhibits Williams–Landel–Ferry (WLF) behavior. The logarithm of relative conductance for PPP(EO)_x/y/LiCF₃SO₃ decreases almost linearly with increasing pressure but increases with salt concentration and side-chain length. As temperature increases, the activation volume becomes smaller but remains positive for PPP(EO)_x/y/LiCF₃SO₃. At higher salt concentrations and longer side-chain lengths, a smaller activation volume for the ion motion is found. These results can be interpreted such that PPP(EO)_x/y/LiCF₃SO₃ behaves like a true polymer electrolyte where ion transport is mediated by segmental motions of the EO side-chains. The addition of tetraethylene glycol dimethyl ether (TEGDME) as a plasticizer increases the activation volume but reduces the conductance.     

铬和镍的添加对Fe3Al合金力学性能影响的DFT研究

利用第一原理研究了过渡金属元素 Cr 或 Ni 在 Fe₃Al合金中的优先占位行为及其合金化效应. 计算结果表明: Cr 或 Ni 的取代有助于Fe₃Al 合金体系更稳定, Cr 优先占据 Fe_I 位, Ni 优先占据 Fe_II位. Fe₂NiAl-II 具有最小的剪切模量G, 杨氏模量E和G/B值, 因此Fe₂NiAl-II合金的韧性、延展性最佳. 态密度和电荷密度图表明, 过渡金属元素的取代提高了它们与近邻基体原子之间的相互作用, 削弱了Al和Fe的相互作用.     

Influence of surface modification of halloysite nanotubes and its localization in PP phase on mechanical and thermal properties of PP/ABS blends

Halloysite nanotubes (HNTs) have been successfully modified using polyethyleneimine (PEI). HNTs and PEI-modified HNTs-filled 80/20 (wt/wt) polypropylene (PP)/acrylonitrile butadiene styrene (ABS) blends and its nanocomposites in the presence of dual compatibilizer have been prepared by melt mixing technique. The refinement in matrix–droplet morphology, selective localization of PEI-modified HNTs, increase in crystallinity of PP phase, formation of β-form of PP crystals and improved dispersion of PEI-modified HNTs in PP phase has resulted in a remarkable improvement in tensile modulus, impact strength and thermal stability of PEI-modified HNTs-filled 80/20 (wt/wt) PP/ABS blends in presence of dual compatibilizer. The increase in tensile modulus, tensile strength and impact strength for PEI-modified HNTs-filled 80/20 (wt/wt) PP/ABS blends in presence of dual compatibilizer are 28.8, 26.6 and 38.5%, respectively.     

Structural, magnetotransport and morphological studies of Sb-doped La2/3Ba1/3MnO3 ceramic perovskites

We report here the structural, magnetotransport and morphological studies of Sb-doped La_2/3Ba_1/3Mn_1−xSb_xO₃ perovskite manganites. Pristine material La_2/3Ba_1/3MnO₃ (LBMO) shows two insulator-metal (I-M) transitions in the electrical resistivity-temperature (ρ-T) behavior. While the higher temperature transition (T_P1) at ∼340 K is reminiscent of the usual I-M transition in manganites, the lower temperature transition (T_P2) at ∼250 K has been ascribed to the grain boundary (GB) effects arising out of the ionic size mismatch between the ions present at the rare-earth site (La³⁺ and Ba²⁺). With Sb-doping T_P1 shifts to lower temperatures while T_P2 remains invariant up to 3% and shifts to lower temperature for 5%. Room temperature electrical resistivity and the peak values also increase successively with Sb-doping. Scanning electron micrographs of the samples exhibit a gradual increase in their grain sizes with Sb indicating a gradual decrease in the GB density. Shift of T_P1 with doping is explained on the basis of a competition between double-exchange and super-exchange mechanisms. The overall electrical resistivity increases and the shift in the electrical resistivity hump (T_P2) with Sb-doping is found related to be gradually decreasing GB density and the ensuing lattice strain increase at the GBs. The intrinsic magnetoresistance (MR) gets suppressed and extrinsic MR gets enhanced with Sb-doping. At T>T_P1, the electrical resistivity is found to follow the adiabatic polaron hopping model whereas the electron-magnon scattering is found to dominate in the metallic regime (T<T_P1).     

Structural, thermal and optical studies of mechanical alloyed Ga40Se60 mixture

A mixture of elemental Ga and Se with the nominal composition Ga₄₀Se₆₀ was submitted to the Mechanical alloying technique and their structural, thermal and optical properties were followed by X-ray diffraction, differential thermal analysis, photoacoustic spectroscopy, UV-VIS‐NIR absorbance spectroscopy and Raman spectroscopy techniques. After 10 h of milling the X-ray pattern showed monoclinic Ga₂Se₃ phase nucleation, which is in the nanometric form, and also a minority amorphous phase. The DSC results showed exothermic reactions between 430 and 720 K attributed to amorphous-crystalline phase transition and structural relaxation of Ga₂Se₃ phase. Based on this a small amount of the as-milled sample was annealed at 723 K. Its XRD pattern showed evidences of grain growth, reduction of the interfacial component, as well as, disappearance of the amorphous phase. The annealing process induced thermal diffusivity increasing, while the optical band gap energy and Raman profile remained practically unchanged.     

EXAFS and XRD studies of an amorphous Co57Ti43 alloy produced by mechanical alloying

We have investigated the local atomic order of an amorphous Co₅₇Ti₄₃ alloy produced by mechanical alloying by means of x-ray diffraction and EXAFS analyses on Co and Ti K-edges. Average coordination numbers and average interatomic distances between first neighbors where found from EXAFS and compared with those determined using an additive hard sphere (AHS) model associated with an deconvolution, and also with data from bcc- Co₂Ti compound. EXAFS results obtained indicated a shortening in the Co-Ti and Ti-Ti average interatomic distances when compared to those found by using the AHS-RDF method and an increase in the Co-Co and Ti-Ti average interatomic distances and a shortening in the Co-Ti one when compared to the interatomic distances found in the bcc- Co₂Ti compound. In spite of these differences, average coordination numbers obtained from EXAFS and AHS-RDF are similar to each other and also to those found in bcc- Co₂Ti.