The effect of 3-aminopropyltrimethoxysilane on the formation of NiFe2O4/SiO2 nanocomposites

NiFe₂O₄/SiO₂ nanocomposites were prepared using a sol–gel method with the addition of 3-aminopropyltrimethoxysilane (APS). Different phases and morphologies of NiFe₂O₄/SiO₂ nanocomposites were obtained when different amounts of APS were used. The structural properties of the products were examined by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Sheet-like morphology was observed at higher molar ratio of APS to NiFe₂O₄, while spherical NiFe₂O₄/SiO₂ nanoparticles separated from each other were formed at lower molar ratio of APS to NiFe₂O₄. The magnetic properties of the nanocomposites were also investigated, indicating that the interparticle interactions exhibit strong dependence on the molar ratio of APS to NiFe₂O₄.     

Studies on polyethylene glycol coating on NiFe2O4 nanoparticles for biomedical applications

The NiFe₂O₄ nanoparticles were prepared by the combustion method and these nanoparticles were successfully coated with polyethylene glycol (PEG) for the possible biomedical applications such as magnetic resonance imaging, drug delivery, tissue repair, magnetic fluid hyperthermia etc. The structural and magnetic characterizations of NiFe₂O₄ nanoparticles were carried out by x-ray diffraction and vibrating sample magnetometry techniques, respectively. The morphology of the uncoated and coated nanoparticles was studied by scanning electron microscopy. The existence of PEG layer on NiFe₂O₄ nanoparticles was confirmed by fourier transform infrared spectroscopy technique.     

Magnetic nanoparticles coated with polysaccharide polymers for potential biomedical applications

This study reports a two-steps route for obtaining magnetic nanoparticles–polysaccharide hybrid materials consisting of Fe₃O₄, NiFe₂O₄ and CuFe₂O₄ nanoparticles synthesis by coprecipitation method in the presence of a soft template followed by coating of ferrite nanoparticles of 8–10-nm size range with polysaccharide type polymers—sodium alginate or chitosan. Magnetic oxide nanoparticles and the corresponding hybrid materials were characterized by X-ray diffraction (XRD), Mössbauer spectroscopy, atomic absorption spectroscopy (AAS), FTIR spectroscopy, scanning and transmission electron microscopy (SEM and TEM) and specific surface area measurements. The vibrating sample magnetometry confirms the superparamagnetic properties of the synthesized ferrites and hybrids. Using this route, the percent of magnetic nanoparticles retained in chitosan-based hybrid materials is nearly double in comparison with that of sodium alginate–based materials. The biological activity tests on Escherichia coli ATCC 25922, Pseudomonas aeroginosa ATCC 27853, Staphylococcus aureus ATCC 25923 and Candida scotti microorganisms show the non-toxic properties of prepared hybrid materials.     

Microwave synthesis of magnetic Fe3O4 nanoparticles used as a precursor of nanocomposites and ferrofluids

Methods to synthesize magnetic Fe₃O₄ nanoparticles and to modify the surface of particles are presented in the present investigation. Fe₃O₄ magnetic nanoparticles were prepared by the co-precipitation of Fe³⁺ and Fe²⁺, NH₃·H₂O was used as the precipitating agent to adjust the pH value, and the aging of Fe₃O₄ magnetic nanoparticles was accelerated by microwave (MW) irradiation. The obtained Fe₃O₄ magnetic nanoparticles were characterized by Fourier transform infrared spectroscopy (FT-IR), transmission electron microscopy (TEM), X-ray powder diffraction (XRD) and vibrating sample magnetometer (VSM). The average size of Fe₃O₄ crystallites was found to be around 8–9 nm. Thereafter, the surface of Fe₃O₄ magnetic nanoparticles was modified by stearic acid. The resultant sample was characterized by FT-IR, scanning electron microscopy (SEM), XRD, lipophilic degree (LD) and sedimentation test. The FT-IR results indicated that a covalent bond was formed by chemical reaction between the hydroxyl groups on the surface of Fe₃O₄ nanoparticles and carboxyl groups of stearic acid, which changed the polarity of Fe₃O₄ nanoparticles. The dispersion of Fe₃O₄ in organic solvent was greatly improved. Effects of reaction time, reaction temperature and concentration of stearic acid on particle surface modification were investigated. In addition, Fe₃O₄/polystyrene (PS) nanocomposite was synthesized by adding surface modified Fe₃O₄ magnetic nanoparticles into styrene monomer, followed by the radical polymerization. The obtained nanocomposite was tested by thermogravimetry (TG), differential scanning calorimetry (DSC) and XRD. Results revealed that the thermal stability of PS was not significantly changed after adding Fe₃O₄ nanoparticles. The Fe₃O₄ magnetic fluid was characterized using UV–vis spectrophotometer, Gouy magnetic balance and laser particle-size analyzer. The testing results showed that the magnetic fluid had excellent stability, and had susceptibility of 4.46×10⁻⁸ and saturated magnetization of 6.56 emu/g. In addition, the mean size d (0.99) of magnetic Fe₃O₄ nanoparticles in the fluid was 36.19 nm.     

The study of transition on NiFe2O4 nanoparticles prepared by co-precipitation/calcination

In this study, the NiFe₂O₄ nanoparticles have been prepared by co-precipitation and calcination process. Using a vibrating sample magnetometer (VSM), transmission electron microscopy (TEM), X-ray diffraction (XRD), energy dispersive spectrometer of X-ray (EDX), and X-ray photoelectron spectroscopy (XPS), the samples obtained by co-precipitation and then by further calcination have been analyzed. The experimental results show that the precursor synthesized by co-precipitation is the composite of both amorphous FeOOH and Ni(OH)₂, but has no amorphous NiFe₂O₄. The results of both EDX and XPS revealed that the FeOOH species is wrapped up by Ni(OH)₂ species. In the calcination process, the amorphous composite is dehydrated and transformed gradually into crystalline NiFe₂O₄ nanoparticles, with the metal ions diffusing. The reaction is different from the one used to prepare other ferrite (e.g., CoFe₂O₄, MnFe₂O₄, Fe₃O₄, etc.) nanoparticles directly by co-precipitation. With increasing calcination temperature, the NiFe₂O₄ grains grow and the magnetization is enhanced.     

Synthesis and characteristics of multifunctional Fe3O4-SiO2-CdS magnetic-fluorescent nanocomposites

A luminescent superparamagnetic nanocomposite with an Fe 3 O 4-SiO 2-CdS structure is synthesized.Coated with a silica shell,Fe 3 O 4 nanoparticles and CdS quantum dots (QDs) are successfully assembled together.Analysed from the test results of X-ray diffraction (XRD),transmission electron microscopy (TEM),high resolution transmission electron microscopy (HRTEM),hysteresis loop,and photoluminescence (PL) spectrum,these nanocomposites exhibit superparamagnetic and photoluminescent properties.     

Synthesis, characterization and infrared emissivity study of polyurethane/TiO2 nanocomposites

In this study, polyurethane/titania (PU/TiO₂) nanocomposites were prepared in ultrasonic process and characterized by fourier transform IR spectroscopy (FT-IR), powder X-ray diffraction (XRD), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and infrared emissivity analysis. The TEM and SEM results indicated that the nanoparticles were dispersed homogeneously in PU matrix on nanoscale. TGA-DSC confirmed that the heat stability of the composite was improved. Infrared emissivity study showed that the nanocomposite possessed lower emissivity value than those values of pure polymer and nanoparticles.     

Chemical synthesis of spinel nickel ferrite (NiFe2O4) nano-sheets

The present investigation is related to the deposition of single-phase nano-sheets spinel nickel ferrite (NiFe₂O₄) thin films onto glass substrates using a chemical method. Nano-sheets nickel ferrite films were deposited from an alkaline bath containing Ni²⁺ and Fe²⁺ ions. The films were characterized for their structural, surface morphological and electrical properties by means of X-ray diffraction (XRD), transmission electron microscope (TEM), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and two-point probe electrical resistivity techniques. The X-ray diffraction pattern showed that NiFe₂O₄ nano-sheets are oriented along (3 1 1) plane. The FT-IR spectra of NiFe₂O₄ films showed strong absorption peaks around 600 and 400 cm⁻¹ which are typical for cubic spinel crystal structure. Microstructural study of NiFe₂O₄ film revealed nano-sheet like morphology with average sheet thickness of 30 nm. The room temperature electrical resistivity of the NiFe₂O₄ nano-sheets was 10⁷ Ω cm.     

Magnetic field synthesis of Fe3O4 nanoparticles used as a precursor of ferrofluids

Methods to synthesize magnetic Fe₃O₄ nanoparticles and to modify the nanoparticle surface are presented in this paper. In these methods, Fe₃O₄ nanoparticles were prepared by co-precipitation, and the aging of nanoparticles was improved by applied magnetic field. The obtained nanoparticles were characterized by Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), X-ray powder diffraction (XRD), and vibrating sample magnetometer (VSM). Thereafter, to enhance the compatibility between nanoparticles and water, an effective surface modification method was developed by grafting acrylic acid onto the nanoparticle surface. FT-IR, XRD, transmission electron microscopy (TEM), and thermogravimetry (TG) were used to characterize the resultant sample. The testing results indicated that the polyacrylic acid chains have been covalently bonded to the surface of magnetic Fe₃O₄ nanoparticles. The effects of initiator dosage, monomer concentration, and reaction temperature on the characteristics of surface-modified Fe₃O₄ nanoparticles were investigated. Moreover, the Fe₃O₄-g-PAA hybrid nanoparticles were dispersed in water to form ferrofluids (FFs). The obtained FFs were characterized by UV–vis spectrophotometer, Gouy magnetic balance and laser particle-size analyzer. The testing results showed that the high-concentration FF had excellent stability, with high susceptibility and high saturation magnetization. The rheological properties of the FFs were also investigated using a rotating rheometer.     

Exchange coupling behavior in bimagnetic CoFe2O4/CoFe2 nanocomposite

In this work we report a study of the magnetic behavior of ferrimagnetic oxide CoFe₂O₄ and ferrimagnetic oxide/ferromagnetic metal CoFe₂O₄/CoFe₂ nanocomposite. The latter compound is a good system to study hard ferrimagnet/soft ferromagnet exchange coupled. Two steps were followed to synthesize the bimagnetic CoFe₂O₄/CoFe₂ nanocomposite: (i) first, preparation of CoFe₂O₄ nanoparticles using a simple hydrothermal method, and (ii) second, reduction reaction of cobalt ferrite nanoparticles using activated charcoal in inert atmosphere and high temperature. The phase structures, particle sizes, morphology, and magnetic properties of CoFe₂O₄ nanoparticles were investigated by X-Ray diffraction (XRD), Mossbauer spectroscopy (MS), transmission electron microscopy (TEM), and vibrating sample magnetometer (VSM) with applied field up to 3.0 kOe at room temperature and 50 K. The mean diameter of CoFe₂O₄ particles is about 16 nm. Mossbauer spectra revealed two sites for Fe³⁺. One site is related to Fe in an octahedral coordination and the other one to the Fe³⁺ in a tetrahedral coordination, as expected for a spinel crystal structure of CoFe₂O₄. TEM measurements of nanocomposite showed the formation of a thin shell of CoFe₂ on the cobalt ferrite and indicate that the nanoparticles increase to about 100 nm. The magnetization of the nanocomposite showed a hysteresis loop that is characteristic of exchange coupled systems. A maximum energy product (BH)_max of 1.22 MGOe was achieved at room temperature for CoFe₂O₄/CoFe₂ nanocomposites, which is about 115% higher than the value obtained for CoFe₂O₄ precursor. The exchange coupling interaction and the enhancement of product (BH)_max in nanocomposite CoFe₂O₄/CoFe₂ are discussed.     

Preparation and characterization of NiFe2O4/NiO composite film via a single-source precursor route

NiFe₂O₄/NiO nanocomposite thin films have been successfully prepared through a facile route using nickel iron layered double hydroxide (NiFe-LDH) as a single-source precursor. This synthetic approach mainly involves the formation of NiFe-LDH film by casting the slurry of NiFe-LDH precursor on the α-Al₂O₃ substrate, followed by high-temperature calcination. The composition, microstructure and properties of the films were characterized in detail by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDX) and vibrating sample magnetometer (VSM). The results indicate that NiFe₂O₄/NiO composite film was composed of granules with diameter less than 100 nm, and the thickness of the film was in the range 1-2 μm. The magnetization of the film can be tuned by alternating the Ni/Fe molar ratio of LDH precursor. In addition, the method developed should be easily extended to fabricate other MFe₂O₄/MO composite film systems with specific applications just by an appropriate combination of divalent/trivalent composition in the precursor of LDHs.     

Structural and polarization properties of polyimide/TiO2 nanocomposites

Polyimide (PI)/titanium dioxide (TiO₂) nanocomposite films were prepared by a solution mixing method with different contents of TiO₂ nanoparticles. The structural and thermal properties of pure PI and PI/TiO₂ nanocomposite films were studied by several techniques such as scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and thermally stimulated depolarization current (TSDC). The SEM and AFM measurements show the uniform dispersion of TiO₂ nanoparticles in PI matrix, and it is also observed that the value of average roughness increases with increasing the contents of TiO₂ nanoparticles. The XRD pattern shows the presence of TiO₂ nanoparticles in PI matrix. It has been observed that the average crystallite size and percentage of crystallinity increase with content of the TiO₂ nanoparticles. FTIR spectra depict the position of different bonds in PI and nanocomposite samples. The TSDC results represent the modification of polarization phenomenon after filling of PI by titania nanoparticles.     

Study of alternating current conduction mechanism in polypyrrole-magnesium ferrite hybrid nanocomposite through correlated barrier hopping model

In the present work, both polypyrrole (PPy) and optimized polypyrrole–magnesium ferrite (PPy-MgFe₂O₄) hybrid nanocomposite were synthesized separately by simple oxidative chemical polymerization method and then structurally characterized using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. The FTIR spectrum of the composite showed the presence of characteristic absorption bands of both PPy and MgFe₂O₄ in the composite confirming interfacial interaction of PPy with MgFe₂O₄. That this interaction is not affected by crystalline behaviour of predominant MgFe₂O₄ particles but that MgFe₂O₄ has embedded in PPy matrix was confirmed by XRD studies. Agglomerated granular spherical morphology of the composite was confirmed by SEM studies. Decrease in AC conductivity of the composite as compared to PPy due to the formation of interfacial heterojunction barrier between p-type PPy and n-type MgFe₂O₄ was confirmed experimentally and well supported theoretically by calculating binding energy, hopping distance and density of states at Fermi level of PPy and the composite as per CBH model.     

One‐Dimensional Magnetic Composite of Polypyrrole‐Containing Carbon Nanotubes/Ni0.75Zn0.25Fe2O4

A novel one‐dimensional electromagnetic nanocomposite of polypyrrole (PPY) containing carbon nanotubes (CNTs)/Ni_0.75Zn_0.25Fe₂O₄ was synthesized by an in‐situ polymerization method. The composite was characterized by x‐ray diffraction (XRD), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM) and Fourier transform infrared. The XRD results confirmed that PPY, CNTs, and Ni_0.75Zn_0.25Fe₂O₄ coexisted in the composite. The TEM and HRTEM results indicated that PPY coated the surface of the CNTs/Ni_0.75Zn_0.25Fe₂O₄ with a thickness of 15–30 nm. The lattice spacings, according to the first main peak of the CNTs, Ni_0.75Zn_0.25Fe₂O₄, and PPY, was about 0.34 nm, 0.25 nm, and 0.42 nm, respectively. The FTIR result also indicated that the PPY formed in the composite. A test of magnetic properties indicated that the composite was ferromagnetic with the saturated magnetization of 12.86 electromagnetic units (emu)/g, and the coercive of 127.18 Oersted (Oe).     

Combustion synthesis of nickel ferrite powders: Effect of NaClO4 content on their characteristics and magnetic properties

Magnetic powders of nickel ferrite (NiFe₂O₄) were successfully synthesized by combustion synthesis in air using iron (Fe), iron oxide (Fe₂O₃), and nickel oxide (NiO) as reactants and sodium perchlorate (NaClO₄) as fuel (or oxidizing agent). The thermal behaviors were characterized using thermogravimetric analysis (TG) and differential thermal analysis (DSC). The as-combusted and final nickel ferrite powders were characterized in terms of chemical composition and morphology by X-Ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), and scanning electron microscopy (SEM) coupled with energy dispersive X-Ray spectroscopy (EDX). In addition, magnetic properties were examined by vibrating sample magnetometer (VSM). The results of TG/DSC analysis indicated that increasing the content of NaClO₄ increased the exothermicity of combustion reaction. XRD indicated that the final nickel ferrite powders formed a single spinel NiFe₂O₄ phase when the amount of NaClO₄ used was 0.08 or 0.10 mol. SEM revealed roughly octahedron particles with sizes in a sub-micrometer range (∼500 nm). All final products exhibited soft magnetism and, synthesis that included 0.1 mol of NaClO₄ produced pure NiFe₂O₄ powders that had a saturation magnetization (M_s) of 58.93 emu/g, which is higher than the reported value (55 emu/g) for the bulk product.     

Microemulsion-mediated in-situ synthesis and magnetic characterization of polyaniline/Zn<Subscript>0.5</Subscript>Cu<Subscript>0.5</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanocomposite

Polyaniline/Zn_0.5Cu_0.5Fe₂O₄ nanocomposite was synthesized by a simple, general and inexpensive in-situ polymerization method in w/o microemulsion. The effects of polyaniline coating on the magnetic properties of Zn_0.5Cu_0.5Fe₂O₄ nanoparticles were investigated. The structural, morphological and magnetic properties of as-prepared samples were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectra, scanning electron microscopy (SEM) and magnetic measurements. The morphology analysis confirmed that polyaniline was deposited on the porous surface of magnetic Zn_0.5Cu_0.5Fe₂O₄. It was shown that the saturation magnetization and coercivity of Zn_0.5Cu_0.5Fe₂O₄ decreased after polyaniline coating, which can be interpreted by the interparticle dipole–dipole interactions that contributed to magnetic anisotropy and changed the magnetic properties of the nanoparticles. PACS  74.25.Ha; 81.05.-t; 81.05.Lg     

Preparation and electrochemistry of one-dimensional nanostructured MnO2/PPy composite for electrochemical capacitor

One-dimensional nanostructured manganese dioxide/polypyrrole (MnO₂/PPy) composite was prepared by in situ chemical oxidation polymerization of pyrrole in the host of inorganic matrix of MnO₂, using complex of methyl orange (MO)/FeCl₃ as a reactive self-degraded soft-template. The morphology and structure of the composite were characterized by infrared spectroscopy (IR) X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that the MnO₂/PPy composite consists of α-MnO₂ and PPy with nanotube-like structure. Electrochemical properties of the composite demonstrated the material showed good electrochemical reversibility after 500 charge-discharge cycles in the potential range of −0.4 to 0.6 V, the tube-like nanocomposite has the potential application in electrochemical capacitor.     

Investigations on structural and magnetic properties of cobalt ferrite/silica nanocomposites prepared by the coprecipitation method

Magnetic nanocomposites consisting of cobalt ferrite nanoparticles embedded in silica matrix were prepared by the coprecipitation method using metallic chlorides as precursors for ferrite. Subsequently composites were annealed at 100, 200 and 300 °C for 2 h. The samples were structurally characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM). The magnetic properties were measured in the temperature range of 10-300 K using vibrating sample magnetometer (VSM). The effects of thermal treatment on structural and magnetic properties of nanocomposites were investigated. When the samples were annealed, CoFe₂O₄ nanocrystallites were observed in the SiO₂ matrix, whose size increases with increase in annealing temperature. The coercivity and saturation magnetization of nanocomposite (annealed at 300 °C for 2 h) are much higher than that of bulk cobalt ferrite. The realization of adjustable particle sizes and controllable magnetic properties makes the applicability of the CoFe₂O₄ nanocomposite more versatile.     

Green synthesis of soya bean sprouts-mediated superparamagnetic Fe3O4 nanoparticles

Superparamagnetic Fe₃O₄ nanoparticles were first synthesized via soya bean sprouts (SBS) templates under ambient temperature and normal atmosphere. The reaction process was simple, eco-friendly, and convenient to handle. The morphology and crystalline phase of the nanoparticles were determined from scanning electron microscopy (SEM), transmission electron microscopy (TEM), selected area electron diffraction (SAED), and X-ray diffraction (XRD) spectra. The effect of SBS template on the formation of Fe₃O₄ nanoparticles was investigated using X-ray photoemission spectroscopy (XPS) and Fourier-transform infrared spectroscopy (FT-IR). The results indicate that spherical Fe₃O₄ nanoparticles with an average diameter of 8 nm simultaneously formed on the epidermal surface and the interior stem wall of SBS. The SBS are responsible for size and morphology control during the whole formation of Fe₃O₄ nanoparticles. In addition, the superconducting quantum interference device (SQUID) results indicate the products are superparamagnetic at room temperature, with blocking temperature (T_B) of 150 K and saturation magnetization of 37.1 emu/g.     

Nanostructural and magnetic studies of virtually monodispersed NiFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanocrystals synthesized by a liquid–solid-solution assisted hydrothermal route

This study presents a comprehensively and systematically structural, chemical and magnetic characterization of ~9.5 nm virtually monodispersed nickel ferrite (NiFe₂O₄) nanoparticles prepared using a modified liquid–solid-solution (LSS) assisted hydrothermal method. Lattice-resolution scanning transmission electron microscope (STEM) and converged beam electron diffraction pattern (CBED) techniques are adapted to characterize the detailed spatial morphology and crystal structure of individual NiFe₂O₄ particles at nano scale for the first time. It is found that each NiFe₂O₄ nanoparticle is single crystal with an fcc structure. The morphology investigation reveals that the prepared NiFe₂O₄ nanoparticles of which the surfaces are decorated by oleic acid are dispersed individually in hexane. The chemical composition of nickel ferrite nanoparticles is measured to be 1:2 atomic ratio of Ni:Fe, indicating a pure NiFe₂O₄ composition. Magnetic measurements reveal that the as-synthesized nanocrystals displayed superparamagnetic behavior at room temperature and were ferromagnetic at 10 K. The nanoscale characterization and magnetic investigation of monodispersed NiFe₂O₄ nanoparticles should be significant for its potential applications in the field of biomedicine and magnetic fluid using them as magnetic materials.