Effect of Wood Flour on the Curing Behavior,Mechanical Properties,and Water Absorption of Natural Rubber/Wood Flour Composites

The preparation of natural rubber/wood flour (NR/WF) composites and the influence of WF content, modification, and particle size on the vulcanizing behavior, mechanical properties, and water absorption of NR/WF composites are described. Results show that the addition of WF into NR delayed the scorching time and vulcanizing time of NR. The appropriate WF contents can improve the mechanical properties of NR. However, the overloading of WF destroys the mechanical properties of NR. The addition of WF increased the water absorption of NR. The silicone couple agents that were used to modify the WF had little effect on the water absorption of NR/WF composites. Decreasing the WF particle size enhanced the water absorption of NR/WF composites because the water-absorbing surface area increased with decreasing WF particle size. The water absorption of sisal-fiber-filled NR-based composites was larger than that of the WF-filled NR-based composites. A useful equation, w=ktⁿ , was inferred from the water absorption results to calculate the water absorption (w) of the NR/WF composites as a function of time (t), where k was a constant concerning the compounds’ character that was primarily determined by the WF's character and n was the power of time that was related to the NR's inherent character, such as cross-linking density, and primarily determined the water absorption rate.     

Rheological and Mechanical Characterization of Multi-Walled Carbon Nanotubes/Polypropylene Nanocomposites

The rheology and morphology of multi-walled carbon nanotube (MWNT)/polypropylene (PP) nanocomposites prepared via melt blending was investigated. The minor phase content of MWNT varied between 0.25 and 8 wt%. From morphological studies using a scanning electron microscopy technique a good dispersion of carbon nanotubes in the PP matrix was observed. The rheological studies were performed by a capillary rheometer, and mechanical properties of the nanocomposites were studied using a tensile and flexural tester. Both PP and its nanocomposites showed non-Newtonian behavior. At low shear rates the addition of MWNT content causes an increase in viscosity; however, viscosity is less sensitive to addition of MWNT content at higher shear rates. Flow activation energy for the nanocomposites was calculated using an Arrhenius type equation. From this calculation it was concluded that the temperature sensitivity of nanocomposites was increased by increasing of nanotube content. An increase in tensile and flexural moduli and Izod impact strength was also observed by increasing the MWNT content. From rheological and mechanical tests it was concluded that the mechanical and rheological percolation threshold is at 1.5 wt%.     

Morphological,Thermal, and Electrical Characterization of Syndiotactic Polypropylene/Multiwalled Carbon Nanotube Composites

In this work, syndiotactic polypropylene/multiwalled carbon nanotubes (MWCNT) nanocomposites, in various concentrations, were produced using melt mixing. The influence of the addition of MWCNT on the morphology, crystalline form, and the thermal and electrical properties of the polymer matrix was studied. To that aim, scanning electron microscopy, Raman spectroscopy, X-ray diffraction, differential scanning calorimetry, and dielectric relaxation spectroscopy were employed. Significant alterations of both the crystallization behavior and the thermal properties of the matrix were found on addition of the carbon nanotubes: conversion of the disordered crystalline form I to the ordered one, increase of the crystallization temperature and the degree of crystallinity, and decrease of the glass transition temperature and the heat capacity jump. Finally, the electrical percolation threshold was found between 2.5–3.0 wt.% MWCNT. For comparison purposes, the results of the system studied here are also correlated with the findings from a previous work on the isotactic polypropylene/MWCNT system.     

Electrical Properties of Isotactic Polypropylene/Multiwalled Carbon Nanotubes Composites Prepared by Vibration Injection Molding

To study the effect of vibration field on the electrical conductivity properties of nanocomposites, isotactic polypropylene (iPP)/multiwalled carbon nanotubes (MWCNT) composites were prepared by conventional injection molding and vibration injection molding. Results showed that the electrical conductivity of iPP/MWCNT composites was significantly promoted by vibration injection molding. Vibration injection molded samples had a percolation threshold of about 2.7 wt% compared with the threshold of about 4.5 wt% for conventional injection molded samples. The effects of test locations and vibration frequency on the electrical conductivity of composites were investigated. The samples exhibited an inhomogeneity along the injection direction. The electrical conductivity of the samples was different at different test locations and increased with increasing vibration frequency. Polarized light microscopy (PLM) results indicated that vibration injection molding can induce MWCNT aggregates to be stretched and oriented along the flow direction, which could form conductive networks and greatly enhance the electrical conductivity of iPP/MWCNT composites.     

Studies on the Nonisothermal Crystallization Behavior of Polypropylene/Multiwalled Carbon Nanotubes Nanocomposites

Polypropylene/multiwalled carbon nanotubes (PP/MWNTs) nanocomposites were prepared by a melt compounding process. The morphology and nonisothermal crystallization of these nanocomposites were investigated by means of optical microscopy, scanning electron microscopy, and differential scanning calorimetry. Scanning electron microscope micrographs of PP/MWNTs composite showed that the MWNTs were well dispersed in the PP matrix and displayed a clear nucleating effect on PP crystallization. Avrami theory, modified by Jeziorny and Mo's method, was used to analyze the kinetics of the nonisothermal crystallization process. It was found that the addition of MWNTs improved the crystallization rate and increased the peak crystallization temperature of the PP/MWNTs nanocomposites as compared with PP. The results show that the Jeziorny theory and Mo's method successfully describe the nonisothermal crystallization process of PP and PP/MWNTs nanocomposites.     

Properties of Polypropylene/Antibacterial Glass Composites

Polypropylene (PP)/antibacterial glass composites were prepared by melt blending PP and silver-doped glass. The antibacterial activity of the PP composites was examined by the method of plate counting, and the crystallization behaviors of pure PP and antibacterial glass/PP composites were compared via hot-stage polarized optical microscopy (POM), X-ray diffraction (XRD), and differential scanning calorimeter (DSC). The results revealed that the antibacterial PP composites had effective antibacterial activity with antibacterial rates more than 90%. The antibacterial agent in the antibacterial glass/PP composites acted as nucleating agents, increasing the crystallization temperature and crystallization rate of PP, but not changing the crystalline modification of PP. The mechanical properties of antibacterial glass/PP composites were also studied, and the results showed that the antibacterial glass improved the stiffness and modulus but decreased the notched impact strength of the PP composites.     

Effects of Carbon Nanotubes on the Morphology and Properties of Uncompatibilized and Maleic Anhydride-grafted Polypropylene-compatibilized Polyamide 6/Polypropylene Blends

The effects of carbon nanotubes (CNTs) on the morphology of uncompatibilized and maleic anhydride-grafted polypropylene (MAPP)-compatibilized polyamide 6 (PA6)/polypropylene (PP) (70/30 w/w) blends prepared using a torque rheometer were investigated. TEM observations showed that the CNTs were selectively located in the major PA6 phase and at the interface. Such localization of nanofillers in the literature usually leads to a refinement in a sea-island morphology. Unexpectedly, our results show that increasing amounts of CNTs in the samples prepared using a torque rheometer led to a transformation from typical sea-island morphology to co-continuous morphology for uncompatibilized PA6/PP blends and to partial fibrillization of the PP domains for MAPP-compatibilized PA6/PP blends. These unusual morphological changes are attributed to a retarded morphology evolution process caused by the CNTs. According to rheological measurements and theoretical analysis, this was achieved through the role of CNTs in enhancing the viscoelasticity of the PA6 phase and promoting interfacial slip. The electrical resistivites, crystallization, and melting behavior of all samples were also studied.     

Dynamic Mechanical and Dielectric Properties of Ethylene Vinyl Acetate/Carbon Nanotube Composites

A comparative study of the dielectric and mechanical properties of ethylene vinyl acetate copolymer (EVA) filled with various concentrations of pristine and modified carbon nanotubes is reported. The surface of the carbon nanotubes was modified with 4-(2-(cholesteryloxycarboxy)ethyl) phenyl to improve the interaction of the filler with the block copolymer matrix. The improved interaction and the better dispersion of the modified carbon nanotubes (mMWCNTs) were demonstrated by a detailed study of the EVA molecular mobility through dynamic mechanical analysis and broadband dielectric relaxation spectroscopy. The storage modulus of the nanocomposite with 6 wt.% of mMWCNTs at ?50°C was enhanced by 103%, whereas for the nanocomposite with the same amount of unmodified filler, the storage modulus was only enhanced by 76% compared to the pure elastomeric matrix. This difference is more pronounced in the rubbery region in which the storage moduli were increased by 117% and 48% for the composite with the modified and unmodified fillers, respectively. The morphologies of the nanocomposites were studied with scanning and transmission electron microscopies to demonstrate the dispersion of the mMWCNTs within the EVA matrix.     

Investigation of the Morphological and Mechanical Properties of Polyethylene Terephthalate (PET)/Ethylene Propylene Diene Rubber (EPDM) Blends in the Presence of Multi-Walled Carbon Nanotubes

In this study the blends of polyethylene terephthalate (PET)/ethylene propylene diene rubber (EPDM) in the presence of multi-walled carbon nanotubes (MWCNT) (1 and 3?wt %) were prepared by melt compounding in an internal mixer. Mechanical and morphological properties of the nanocomposites were investigated. The thermal behaviors of the PET/EPDM nanocomposites were also investigated, by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The results of the mechanical tests showed that the tensile strength, elastic modulus and the hardness of the blends were increased with increasing CNT, while the impact strength and elongation at break decreased. The DSC and TGA results showed an increase of melting temperature (T_m) and degradation temperature of the nanocomposites with the addition of the carbon nanotubes, because the carbon nanotubes serve both as nucleating agents to increase T_m and prevent the composite from degradation to increase the thermal stability. The microstructure of the composites was evaluated through field emission scanning electron microscopy (FESEM) and the results showed a good distribution of the MWCNT within the polymer blend.     

Synergistic Effect of Polyhedral Oligomeric Silsesquioxane and Multiwalled Carbon Nanotubes on the Flame Retardancy and the Mechanical and Thermal Properties of Epoxy Resin

A novel polyhedral oligomeric silsesquioxane containing phosphorus and boron (PB-POSS) was synthesized. The resulting PB-POSS and multiwalled carbon nanotubes (MWCNTs) were incorporated into an epoxy resin (EP) to prepare PB-POSS/MWCNTs/EP composites through a solution mixing method. The synergistic effect of MWCNTs and PB-POSS on the thermal and mechanical properties and the flame retardancy of these flame retardant composites were studied. The experimental results showed that the introduction of PB-POSS or MWCNTs further improved the LOI values of the epoxy resin, and the highest LOI value (32.8%) was obtained for the formulation containing 14.6 wt% PB-POSS and 0.4 wt% MWCNTs. In addition, the incorporation of both PB-POSS and MWCNTs significantly improved the thermal and mechanical properties of the composites. The mechanical properties of composites containing 14.7 wt% PB-POSS and 0.3 wt% MWCNTs reached the maximum. The impact strength and flexural strength increased by 42% and 7%, respectively, compared to the neat epoxy resin. Thus, a combination of PB-POSS and MWCNTs in the appropriate ratio could effectively enhance the thermal and mechanical properties and the flame retardancy of the epoxy resin matrix.     

Mechanical and Thermal Properties of Polypropylene/Silica Aerogel Composites

Polypropylene (PP) composites including various amounts of silica aerogel (SA) microparticles were prepared by melt mixing in an internal mixer. The morphology and microstructure of the prepared composites were investigated by scanning electron microscopy (SEM). Mechanical properties of the samples, including elastic modulus, tensile stress, elongation and stress at break, were measured by tensile tests. In addition, the other mechanical features, including Izod impact strength, hardness and wear resistance, were evaluated and then related to the structure of the PP/SA composites. Furthermore, the thermal characteristics of the composites, such as heat deflection temperature and thermal stability, were studied by thermal gravimetric analysis (TGA). The SEM photographs indicated the satisfactory SA particles dispersion for the compositions of 1% and 3% but agglomeration of the aerogels at higher SA contents. Since the composites became stiffer, the impact and tensile strength decreased. The addition of the SA to the PP matrix yielded harder samples with lower weight loss and coefficients of friction in wear tests. The TGA evaluations confirmed that the presence of SA promoted and upgraded the thermal stability and heat deflection temperature of PP. The thermal results proved the superior potential of PP as an insulator when the SA particles were added.     

Mechanical Properties and Morphology of Polypropylene/Polypropylene-g-Maleic Anhydride/Long Glass Fiber Composites

Long glass fiber (LGF)-reinforced polypropylene (PP) was prepared using a self-designed impregnation device. The effect of dicumyl peroxide (DCP) and maleic anhydride (MA) content on the compatibilizer, PP grafted with maleic anhydride (PP-g-MA), was investigated by means of scanning electron microscopy (SEM) and mechanical properties. The experimental results demonstrated that the increase of DCP and MA could effectively improve the interfacial interaction between PP and GF. Good interfacial adhesion between PP and GF in PP/ PP-g-MA /LGF composites was observed from SEM studies for the higher contents of MA. The best mechanical properties of PP/ PP-g-MA /LGF(30%) composites were obtained when the content of DCP and MA were 0.4 and 0.8 wt%, respectively. The storage modulus of the PP/PP-g-MA/LGF composites increased and then decreased with the content of MA. When the content of MA was 0.8 wt%, tan δ had the lowest value, indicating that the corresponding composites had the best compatibility.     

Morphology and Mechanical Properties of Polyamide 6/Acrylonitrile-Butadiene-Styrene Blends Containing Carbon Nanotubes

The blends of polyamide 6/acrylonitrile-butadiene-styrene (PA6/ABS), with added styrene-maleic acid copolymer (SMA) compatibilizer, were prepared through melt mixing in an internal mixer. The effects of blend composition and various process conditions, as well as the addition of multi-wall carbon nanotubes (MWCNTs) to the blends, on the morphology and mechanical properties were investigated. The morphology of the blends and blend nanocomposites were observed by scanning electron microscopy (SEM) and analyzed using an image analysis technique. The mechanical behavior of the blends was investigated by tensile and also impact testing. The results showed that the blend composition as well as the processing conditions significantly affected the morphology and mechanical properties of the PA6/ABS blends. Among the various compositions, the blend with 36?wt.% of ABS and 4?wt.% of SMA compatibilizer exhibited the best mechanical properties. Comparing various speeds and times of mixing, it was found that less mixing speed and longer mixing times resulted in the favorable morphology and conditions for achievement of the desired toughness for the polyamide 6. By adding different amounts of MWCNTs to the blends, it was found that the presence of the carbon nanotubes changed the viscosity of the resulting nanocomposite and thus changed the morphology. These nanocomposites also showed an improvement in mechanical properties. The MWCNTs acted as a second compatibilizer, resulting in a synergistic effect on the mechanical properties of the PA6/ABS blend nanocomposites.     

Mechanical Properties and Rheological Behavior of Dynamically Vulcanized Trans-Polyisoprene/Polypropylene Blends

The degree of dynamic vulcanization, mechanical properties, rheological behavior, and the ageing-resistant performance of thermoplastic vulcanizates (TPVs) based on Trans 1,4-polyisoprene/polypropylene (TPI/PP) blends with the blend ratios of 70/30, 60/40, and 50/50 were investigated. The results showed that TPI fully dynamically vulcanized in the Haake mixer chamber when mixed with PP, and the specimen with the blend ratio 70/30, for the same sulfur content in all samples, had the lowest cross-linking degree of the TPI phase. The shear viscosity of TPI/PP-TPVs dropped as the shear rate increased and the specimen with the blend ratio 70/30 had a relatively greater shear viscosity in the region of shear rates less than 1000 s^?1. With the antiageing agent Vulkanox 4020 NA (Bayer) added, all the TPI/PP-TPVs showed good ageing characteristics, and the specimen with the blend ratio 70/30 possessed the best mechanical properties.     

Mechanical Properties and Crystallization Behavior of Polycarbonate/Polypropylene Blends

The mechanical properties, morphology, and crystallization behavior of polycarbonate (PC)/polypropylene (PP) blends, with and without compatibilizer, were studied by tensile and impact tests, scanning electron microscopy (SEM), X-ray diffraction (XRD), and differential scanning calorimetry (DSC). The tensile and impact strengths of PC/PP blends decreased with increasing the PP content due to poor compatibility between the two phases. But the addition of compatibilizer improved the mechanical properties of the PC/PP blends, and the maximum value of the mechanical properties, such as tensile and impact strengths of PC/PP (80/20 wt%) blends, were obtained when the compatibilizer was used at the amount of 4 phr. The SEM indicated that the compatibility and interfacial adhesion between PC and PP phases were enhanced. DSC results that showed the crystallization and melting peak temperatures of PP increased with the increase of the PP content, which indicated that the amorphous PC affected the crystallization behavior. However, both the PC and compatibilizer had little effect on the crystallinity of PP in PC/PP blends based on both the DSC and XRD patterns.     

Injection Molding Shrinkage and Mechanical Properties of Polypropylene Blends

Polypropylene (PP) blends based on isotactic polypropylene (iPP), propylene-ethylene block copolymer (bPP), and propylene–ethylene random copolymer (rPP) were prepared by melt blending and the effects of content of bPP and rPP on the shrinkage during solidification and storage and mechanical properties of the blends were studied. It was found that the addition of polypropylene copolymer could effectively reduce the processing shrinkage of iPP and the lowest shrinkage of the blends was achieved at a loading of 2 wt% bPP or rPP. The flexural modulus and tensile strength of the blends decreased a little while the impact strength and elongation at break were improved greatly compared with those of iPP.     

Thermal and Tensile Properties of Epoxy Nanocomposites Reinforced by Silane-functionalized Multiwalled Carbon Nanotubes

Epoxy nanocomposites with unmodified multiwalled carbon nanotubes (u-MWCNTs) and silanized multiwalled carbon nanotubes (si-MWCNTs) were prepared by a cast molding method. The effects of 3-aminopropyltriethoxysilane functionalization of MWCNTs on thermal, tensile, and morphological properties of the nanocomposites were examined. The nanocomposites were characterized by thermogravimetric analysis, dynamic mechanical thermal analysis, and tensile testing. The results showed that epoxy composites based on si-MWCNTs showed better thermal stability, glass transition temperature, and tensile properties than the composites based on u-MWCNTs. These results prove the effect of silane functionalization on the interfacial adhesion between epoxy and MWCNTs. This was further confirmed by morphology study of fractured surfaces of nanocomposites by field emission scanning electron microscopy.     

超细0.4nm直径单壁碳管的光学特性

由于纳米碳管的优异机械特性及其丰富多采的光学和电学特性,它自1991年被发现以来一直受到科学家的青睐,纳米碳管研究已成为当今世界上发展最迅速,竞争最激烈的科学前沿领域之一。怎样才能把纳米碳管做得更细小,尺寸更均匀以及如何使众多的纳米碳管排列规整,一直是纳米碳管研究中的难题。我们利用多孔的沸石晶体作为载体,首次成功地研制出了尺寸均一,排列规整的超细单壁纳米碳管,这些超细纳米碳管具有独特的性能,低温下（＜20K）甚至呈现出前所未有的一维超导现象。详细介绍了这些超细单壁纳米碳管的制备过程,并着重介绍其在可见光区的光吸收,光发射以及二次谱波的倍频特性。     

High-Performance Silicone Rubber Composites via Non-Covalent Functionalization of Carbon Nanotubes

A high-performance silicone rubber (SR) composite (denoted as SCT) filled with 5 phr functionalized carbon nanotubes (CNTs) and 40 phr fumed silica (SiO₂) was prepared by mechanical blending. The CNTs were functionalized by tetrakis (phenylmethyl)-thioperoxydi (carbothioamide) (TBzTD); it contains four benzene rings that can interact with the CNTs via π–π interactions. Raman spectroscopy and X-ray photoelectron spectroscopy analysis demonstrated the existence of the π-π interactions between the CNTs and the TBzTD. Transmission electron microscopy and scanning electron microscopy confirmed the uniform dispersion of the CNTs in SR matrix and strong interfacial interactions between the SR and the CNTs. The effects of these non-covalently functionalized CNTs on the mechanical properties of the silica filled SR composites were fully investigated. The results showed that the tear strength of the SCT composite with TBzTD functionalized CNTs was significantly improved, by 249%, compared with that of the composite containing only SiO₂. An obvious crack deflection occurred in the SCT during the tearing process, resulting in the enhanced tear strength.     

Comparison of Mechanical Properties and Rheological Behavior of Trans-Polyisoprene/Polypropylene and Ethylene Propylene Diene Rubber/Polypropylene Thermoplastic Vulcanizates

The degree of dynamic vulcanization, mechanical properties, rheological behavior, and the ageing-resistant performance of trans 1,4-polyisoprene (TPI)/polypropylene (PP) and ethylene propylene diene rubber (EPDM)/PP thermoplastic vulcanizates with a blend ratio of 60/40 were investigated comparatively. The results showed that TPI had fully dynamically vulcanized when mixed with PP in the Hakke mixer chamber (175°C, 60 rpm) while EPDM had only partly dynamically vulcanized due to its saturated main chain backbone. With increased sulfur content, the torque at the end of the curing curves of the two thermoplastic vulcanizates (TPVs) increased in the curing characteristics measuring process as the degree of crosslinking increased. Comparing the two blends, TPI/PP-TPVs were possessed of a better mobility, a little lower tensile strength and tear strength, a little higher 100% modulus and hardness, and much lower elongation at break. EPDM/PP-TPVs had better ageing-resistant characteristics due to EPDM's saturated main chain backbone.