Preparation and Mechanical and Tribological Properties of High-Density Polyethylene/Hydroxyapatite Nanocomposites

High-density polyethylene (HDPE) nanocomposites reinforced with hydroxyapatite nanorods (nHA) were fabricated by means of extrusion and injection molding. The thermal, mechanical, and dry sliding wear properties of HDPE-based nanocomposites filled with nHA loadings up to 20 wt% were investigated. The results of mechanical property characterization showed that nHA additions improved the hardness, elastic modulus, and yield strength of HDPE at the expense of its tensile ductility and impact strength. Thermogravimetric analysis and heat deflection temperature measurements revealed that nHA fillers are very effective to enhance the thermal stability of HDPE. The wear behavior of HDPE/nHA nanocomposites was studied using a pin-on-disk tribometer. nHA fillers of a large aspect ratio improved the wear resistance of HDPE substantially because of their load-bearing effect and the formation of a continuous transfer film on the steel counterface.     

The Effect of Zinc Oxide and Calcium Carbonate Nanoparticles on the Thermal Conductivity of Polypropylene

The thermal conductivity (TC) of compression-moulded polypropylene (PP) and PP filled with 5–15% zinc oxide (ZnO) or calcium carbonate (CaCO₃) nanoparticles, prepared by extrusion, was studied using a thermal conductivity analyzer (TCA). The effect of nanoparticle content and crystallinity on the thermal conductivity was investigated using conventional methods, including SEM, XRD, and DSC. The incorporation of nanoparticles improved the crystallinity and thermal conductivity simultaneously. The experimental TC values of the PP nanocomposites with different level of nanoparticles concentration showed a linear increase with an increase in crystallinity. The TC improvement in PP/ZnO nanocomposite was greater than that of PP/calcium carbonate nanocomposites. This fact can be attributed to the intrinsic, better thermal conductivity of the ZnO nanoparticles. Several models were used for prediction of the TC in the nanocomposites. In the PP/ZnO nanocomposites the TC values correlated well with the values predicted by the Series, Maxwell, Lewis and Nielson, Bruggeman, and De Loor models up to 10 wt%.     

Fabrication and characterization of iron oxide nanoparticles filled polypyrrole nanocomposites

The effect of iron oxide nanoparticle addition on the physicochemical properties of the polypyrrole (PPy) was investigated. In the presence of iron oxide nanoparticles, PPy was observed in the form of discrete nanoparticles, not the usual network structure. PPy showed crystalline structure in the nanocomposites and pure PPy formed without iron oxide nanoparticles. PPy exhibited amorphous structure and nanoparticles were completely etched away in the nanocomposites formed with mechanical stirring over a 7-h reaction. The thermal stability of the PPy in the nanocomposites was enhanced under the thermo-gravimetric analysis (TGA). The electrical conductivity of the nanocomposites increased greatly upon the initial addition (20 wt%) of iron oxide nanoparticles. However, a higher nanoparticle loading (50 wt%) decreased the conductivity as a result of the dominance of the insulating iron oxide nanoparticles. Standard four-probe measurements indicated a three-dimensional variable-range-hopping conductivity mechanism. The magnetic properties of the fabricated nanocomposites were dependent on the particle loading. Ultrasonic stirring was observed to have a favorable effect on the protection of iron oxide nanoparticles from dissolution in acid. A tight polymer structure surrounds the magnetic nanoparticles, as compared to a complete loss of the magnetic iron oxide nanoparticles during conventional mechanical stirring for the micron-sized iron oxide particles filled PPy composite fabrication.     

Crystallization and Thermal Conductivity of CaCO3 Nanoparticle Filled Polypropylene

Isotactic polypropylene (IPP) and calcium carbonate (CaCO₃) nanocomposites were prepared by melt extrusion in a twinscrew extruder. The effect of CaCO₃ nanoparticles on the crystallization and thermal conductivity (TC) of PP was studied by thermal analysis (DSC) and thermal conductivity analysis (TCA). The introduction of CaCO₃ nanoparticles resulted in an increase in crystallinity. The incorporation of this nanoparticle (up to 15 phr) caused a significant increase of TC of PP, especially for larger filler content. Several models were used for prediction of TC of the nanocomposites. The experimental results had a good correlation with the Ce Wen Nan Model.     

Role of curing conditions and silanization of glass fibers on carbon nanotubes (CNTs) reinforced glass fiber epoxy composites

Curing behavior of amino-functionalized carbon nanotubes (ACNT) used as reinforcing agent in epoxy resin has been examined by thermal analysis. Experiments performed as per supplier’s curing conditions showed that modification of the curing schedule influences the thermo-mechanical properties of the nanocomposites. Specifically, the glass transition temperature (T_g) of ACNT-reinforced composites increased likely due to the immobility of polymer molecules, held strongly by amino carbon nanotubes. Further, a set of composites were prepared by implementing the experimentally determined optimal curing schedule to examine its effect on the mechanical properties of different GFRP compositions, while focusing primarily on reinforced ACNT and pristine nanotube (PCNT) matrix with silane-treated glass fibers. From the silane treatment of glass fibers in ACNT matrix composition it has been observed that amino silane is much better amongst all the mechanical (tensile and flexural) properties studied. This is because of strong interface between amino silane-treated glass fibers and modified epoxy resin containing uniformly dispersed amino-CNTs. On the other hand, PCNT GFRP composites with epoxy silanes demonstrated enhanced results for the mechanical properties under investigation which may be attributed to the presence of strong covalent bonding between epoxy silane of glass fiber and epoxy–amine matrix.     

Fabrication and characterization of superparamagnetic and thermoresponsive hydrogels based on oleic-acid-coated Fe3O4 nanoparticles, hexa(ethylene glycol) methyl ether methacrylate and 2-(acetoacetoxy)ethyl methacrylate

Stimuli-responsive hydrogel nanocomposites comprised of swollen polymer networks, in which magnetic nanoparticles are embedded, are a relatively new class of “smart” soft materials presenting a significant impact on various technological and biomedical applications. A novel approach for the fabrication of hydrogel nanocomposites exhibiting temperature- and magneto-responsive behavior involves the random copolymerization of hexa(ethylene glycol) methyl ether methacrylate (HEGMA, hydrophilic, thermoresponsive) and 2-(acetoacetoxy)ethyl methacrylate (AEMA, hydrophobic, metal-chelating) in the presence of preformed oleic-acid-coated magnetite nanoparticles (OA·Fe₃O₄). In total, two series of hydrogel nanocomposites have been prepared in two different solvent systems: ethyl acetate (series A) and tetrahydrofuran (series B). The degrees of swelling (DSs) of all conetworks were determined in organic and in aqueous media. The nanocrystalline phase adopted by the embedded magnetic nanoparticles was investigated by X-ray diffraction (XRD) spectroscopy. The obtained diffraction patterns indicated the presence of magnetite (Fe₃O₄). Deswelling kinetic studies that were carried out at ∼60 °C in water demonstrated the thermoresponsive properties of the hydrogel nanocomposites, attributed to the presence of the hexaethylene glycol side chains within the conetworks. Moreover, thermal gravimetric analysis (TGA) measurements showed that these materials exhibited superior thermal stability compared to the pristine hydrogels. Further to the characterization of compositional and thermal properties, the assessment of magnetic characteristics by vibrational sample magnetometry (VSM) disclosed superparamagnetic behavior. The tunable superparamagnetic behavior exhibited by these materials depending on the amount of magnetic nanoparticles incorporated within the networks combined with their thermoresponsive properties may allow for their future exploitation in the biomedical field.     

EPR investigations of silicon carbide nanoparticles functionalized by acid doped polyaniline

Nanocomposites (SiC-PANI) based on silicon carbide nanoparticles (SiC) encapsulated in conducting polyaniline (PANI) are synthesized by direct polymerization of PANI on the nanoparticle surfaces. The conductivity of PANI and the nanocomposites was modulated by several doping levels of camphor sulfonic acid (CSA). Electron paramagnetic resonance (EPR) investigations were carried out on representative SiC-PANI samples over the temperature range [100–300 K]. The features of the EPR spectra were analyzed taking into account the paramagnetic species such as polarons with spin S=1/2 involved in two main environments realized in the composites as well as their thermal activation. A critical temperature range 200–225 K was revealed through crossover changes in the thermal behavior of the EPR spectral parameters. Insights on the electronic transport properties and their thermal evolutions were inferred from polarons species probed by EPR and the electrical conductivity in doped nanocomposites.     

Luminescence from copper nanoparticles

The presence of copper nanoparticles in alumina and silica modifies their luminescence, and the changes in spectra are influenced by variations in the nanoparticle size distributions. Luminescence signals are sensitive to the total defect population. Thus the luminescence not only reflects changes caused by thermal annealing, which can modify both intrinsic defects and the copper nanoparticles, but also responds to the method of preparation of thin film layers. Copper nanoparticle influence on luminescence is reported both for ion-implanted bulk silica and for copper in pulsed laser deposition within alumina. Luminescence thus potentially offers a non-destructive monitor of the layer quality, reproducibility and growth conditions, as well as the state and size of the copper nanoparticles. Received: 29 June 2001 / Published online: 10 October 2001     

ZnO nanoparticles favours heterogeneous nucleation in PET–ZnO nanocomposites

The structural and chemical properties with non-isothermal crystallization kinetics of PET–ZnO nanocomposites have been reported in this article. ZnO nanoparticles have been synthesized via chemical route with average diameter 19 nm which made confirm by transmission electron microscopy and X-ray diffractometer (XRD) techniques. PET–ZnO nanocomposites have been prepared by solution casting method. The structural and chemical changes occurred in poly (ethylene terephthalate) after inclusion of ZnO nanoparticles have been studied with the help of XRD and Fourier transform infrared spectroscopy, respectively. It was observed from differential scanning calorimeter that ZnO nanoparticles work as nucleating agent for heterogeneous nucleation in PET matrix under non-isothermal crystallization process. The combined Avrami and Ozawa models have been proved adequate to explain non-isothermal crystallization kinetics of PET–ZnO nanocomposites, and also, ZnO nanoparticles have been caused to reduce crystallization activation energy in pristine PET as per the applied Kissinger model.     

Effect of Restricted Geometry on the Structure and Phase Transitions in Potassium Nitrate Nanoparticles

The effect of restricted geometry and thermal prehistory of sample preparation on phase transitions in nanocomposites on base of porous glasses with average pore diameters 7 and 46 nm filled by potassium nitrate have been studied by X-rays and neutron diffraction. The nanoparticle sizes have been determined and phase diagrams (on cooling) for these nanoparticles have been described. It is shown that there is a critical nanoparticle size in the interval from 30 till 20 nm, at which in nanocomposite the ferroelectric phase is realized only regardless of preparation method.     

Fullerene–epoxy nanocomposites-enhanced mechanical properties at low nanofiller loading

In this study, we characterized the mechanical properties of fullerence (C₆₀) epoxy nanocomposites at various weight fractions of fullerene additives in the epoxy matrix. The mechanical properties measured were the Young’s modulus, ultimate tensile strength, fracture toughness, fracture energy, and the material’s resistance to fatigue crack propagation. All of the above properties of the epoxy polymer were significantly enhanced by the fullerene additives at relatively low nanofiller loading fractions (~0.1 to 1% of the epoxy matrix weight). By contrast, other forms of nanoparticle fillers such as silica, alumina, and titania nanoparticles require up to an order of magnitude higher weight fraction to achieve comparable enhancement in properties.     

Modified Maxwell model for predicting thermal conductivity of nanocomposites considering aggregation

The effect of nanoparticle aggregation on the thermal conductivity of nanocomposites or nanofluids is typically nonnegligible. A universal model(Maxwell model) including nanoparticle aggregation is modified in order to predict the thermal conductivity of nanocomposites more accurately. The predicted thermal conductivities of silica and titania nanoparticle powders are compared first with that measured by a hot-wire method and then with those in previous experimental works.The results show that there is good agreement between our model and experiments, and that nanoparticle aggregation in a nanocomposite enhances the thermal conductivity greatly and should not be ignored. Because it considers the effect of aggregation, our model is expected to yield precise predictions of the thermal conductivity of composites.     

Glass transition temperature and thermal stability of ZnS/PMMA nanocomposites

In this article, ZnS nanoparticles were prepared by wet chemical precipitation method using zinc sulphate (ZnSO₄), sodium sulphide (Na₂S) and thio-glycerol. These nanoparticles were characterized through X-ray diffraction (XRD) and transmission electron microscope (TEM) measurements. The solution-based processing was used to prepare Poly methyl methacrylate (PMMA) nanocomposites with different weight percents (0, 2, 4, 6 and 8) of ZnS nanoparticles. The obtained ZnS/PMMA nanocomposites were characterized through XRD, scanning electron microscope and TEM measurements. The dynamic mechanical analyzer was used to obtain the storage modulus and glass transition temperature (T _g) of the nanocomposites. The apparent activation energy of the glass transition region was also determined using the Vogel–Fulcher–Tammann equation. The results indicated that the thermal stability of ZnS/PMMA nanocomposites was higher than PMMA and 6 wt. % of ZnS nanoparticles in PMMA matrix showed the maximum activation energy, which indicated that this nanocomposite had higher thermal stability than other composites.     

Improvement of the mechanical and rheological properties of HDPE/PET/MWCNT nanocomposites

High density polyethylene (HDPE)/poly (ethylene terephthalate) (PET) (90/10 wt.%) blends and HDPE/PET/multi-walled carbon nanotubes (MWCNTs) nanocomposites were prepared by melt mixing process, and the influence of MWCNTs on the mechanical and rheological properties of the nanocomposites was investigated. MWCNTs were added up to 5 wt.% in the HDPE/PET matrix. Transmission electron microscopy images reveal that the MWCNTs were homogeneously dispersed in the HDPE/PET matrix. Improvement of mechanical properties was observed by the addition of MWCNTs compared with HDPE/PET blends. Prominent increases in the complex viscosity and storage modulus of the nanocomposites were found with increasing MWCNT content.     

Structural,electrical and optical properties of MgO-reduced graphene oxide nanocomposite for optoelectronic applications

MgO-reduced graphene oxide nanocomposites (NCs) were synthesized by a simple two-step chemical method. The microstructure, surface morphology, and composition of the prepared samples have been studied. X-ray diffractometer (XRD) analysis confirmed the crystalline cubic MgO nanoparticle and rGO sheets. Scanning electron microscope (SEM) showed the spherical MgO nanoparticles well dispersed over the graphene sheets. UV–visible spectroscopy analysis demonstrated that a red shift in the wavelength dependent absorbance curve. The band gap of the samples was found to be decreased with the increase of rGO content. The dielectric studies have been examined in the frequency range 500 Hz−5 MHz and found significant improvement in the dielectric constant, dielectric loss, and electric properties due to rGO addition.This is mainly attributed to the strong interfacial polarization (Maxwell–Wagner polarization) between MgO and rGO sheets. Further, the modulation of charge carrier density with rGO additions help to enhance the electrical conductivity of NCs and thus, encouraging to have wider application in electronic and energy technologies.     

Synthesis and Thermal Behavior of Silica‐Graft‐Polypropylene Nanocomposites Studied by Step‐Scan DSC and TGA

Silica graft poly(propylene) (silica‐g‐PP) nanocomposites were successfully prepared by radical grafting copolymerization and ring‐opening reaction. Their thermal properties were studied by step‐scan differential scanning calorimetry (SDSC) and thermogravimetric analysis (TGA). The exothermic peaks in the IsoK baseline (C_p,IsoK, nonreversing signal) of SDSC reveal that PP and silica‐g‐PP nanocomposites undergo melting‐recrystallization‐remelting during heating. The peak temperatures of recrystallization and remelting shift upward with the existence of nanoparticles in the PP matrix. The thermal degradation kinetics of silica‐g‐PP nanocomposites were investigated using nonisothermal TGA and the Flynn‐Wall‐Ozawa method. The results indicate that the thermal stability was significantly improved with increasing silica content, mainly because of the physical‐chemical adsorption of the volatile degradation products on the nanoparticles that delays their volatilization during decomposition, and the covalent interaction between nanoparticles and PP chains, which will also reduce the breakage of PP backbone chains.     

In situ Radical Copolymerization in Presence of Surface‐Modified TiO2 Nanoparticles: Influence of a Double Modification on Properties of Unsaturated Polyester (UP) Nanocomposites

In the preparation of nanocomposites, there is competition between the dispersion of nanoparticles and the formation of agglomerates. In this study, radical copolymerization of ethyl acrylate and methyl methacrylate initiated by 2,2‐azobis (isobutyro) nitrile (AIBN) was performed, in the presence of titanium oxide (TiO₂) nanoparticles modified in a new approach; a good dispersion of the nanoparticles in the unsaturated polyester (UP) matrix was obtained. The TiO₂ nanoparticles were exposed to 3‐(methacryloxy) propyl trimethoxy silane as the coupling agent. The presence of coupling agent‐grafted TiO₂ nanoparticles in the copolymerization process resulted in the formation of a polymeric layer on the surface of the TiO₂ nanoparticles (doubly modified‐TiO₂). The grafting of coupling agent molecules and consequently copolymer macromolecular chains onto the surface of TiO₂ nanoparticles was investigated using Fourier transform infrared (FTIR) analysis. It found that the formation of an acrylate layer on the surface of nanoparticles was successful. Then, unsaturated polyester (UP)/TiO₂ nanocomposites were prepared. The morphology was studied using transmission electron microscopy (TEM). Mechanical properties and ultraviolet visible (UV/VIS) spectroscopy of various samples, including the doubly modified‐TiO₂ nanoparticles, with different nanoparticle inclusions and the unmodified‐TiO₂ nanoparticles, were also investigated. The results showed the doubly modified‐TiO₂ nanoparticles, compared to those of unmodified‐TiO₂, had better nanoparticle dispersion causing improvement in the mechanical properties and UV shielding.     

Flow boiling heat transfer of alumina nanofluids in single microchannels and the roles of nanoparticles

This study investigates flow boiling heat transfer of aqueous alumina nanofluids in single microchannels with particular focuses on the critical heat flux (CHF) and the potential dual roles played by nanoparticles, i.e., (i) modification of the heating surface through particle deposition and (ii) modification of bubble dynamics through particles suspended in the liquid phase. Low concentrations of nanofluids (0.001–0.1 vol.%) are formulated by the two-step method and the average alumina particle size is ~25 nm. Two sets of experiments are performed: (a) flow boiling of formed nanofluids in single microchannels where the effect of heating surface modification by nanoparticle deposition is apparent and (b) bubble formation in a quiescent pool of alumina nanofluids under adiabatic conditions where the role of suspended nanoparticles in the liquid phase is revealed. The flow boiling experiments reveal a modest increase in CHF by nanofluids, being higher at higher nanoparticle concentrations and higher inlet subcoolings. The bubble formation experiments show that suspended nanoparticles in the liquid phase alone can significantly affect bubble dynamics. Further discussion reveals that both roles are likely co-existent in a typical boiling system. Properly surface-promoted nanoparticles could minimize particle deposition hence little modification of the heating surface, but could still contribute to the modification in heat transfer through the second mechanism, which is potentially promising for microchannel applications.     

Hybrid nanostructured materials with tunable magnetic characteristics

Novel titanium oxide (TiO₂) nanoparticles were fabricated via a modified propanol drying step. These nanoparticles were loaded with anti-cancer drug paclitaxel (PTX) to yield PTX-TiO₂ nanocomposites. The nanocomposites were characterized for their size and surface morphology employing nanoparticle tracking analysis (NTA) and scanning electron microscopy (SEM). The SEM images showed spherical particles with smooth surface and narrow size distribution of ~30–40 nm, which was also supported by NTA analysis data. The drug loading efficiency of the air-dried nanoparticles was observed to be ~63.61 % while those prepared through propanol-induced drying step showed ~69.70 %, thereby demonstrating higher efficiency of the latter. In vitro pH-dependent release of the loaded PTX was observed with higher release at acidic pH compared with physiological pH. Cell uptake studies suggested of time-dependent internalization of nanocomposites with significant improvement in uptake by increasing incubation time from 2 to 24 h, as evidenced by flow cytometry. Further, the cell viability as a measure of anti-cancer activity revealed that cell viability upon exposure to PTX only was 40.5 % while that of PTX-TiO₂ nanocomposite showed 21.6 % viability after 24 h, suggesting better anti-cancer efficacy of nanocomposites. Apoptosis studies revealed that cells treated with PTX-TiO₂ nanocomposites possessed more amount of apoptotic bodies as compared to those treated with PTX only.     

Preparation and properties of nano-sized Ag and Ag2S particles in biopolymer matrix

Silver (Ag) and silver sulfide (Ag₂S) nanoparticles were synthesized in a sago starch matrix. The resulting nanocomposites were investigated using structural, optical and thermal methods. XRD spectra of the nanocomposites confirmed the presence of nanostructured silver (cubic phase) and silver sulfide (monoclinic phase) in the matrix. TEM micrographs showed that the nanoparticles are mostly spherical in shape. Analyzes of the optical properties of the silver nanocomposite aqueous dispersions/solutions of various concentrations were carried out. The results and the theoretical considerations suggested that at high concentrations there is a release of silver nanoparticles from the composite in the water environment. Further dilution produces homogeneous solution in which silver nanoparticles are capped with starch macromolecules. TGA analysis revealed reduced thermal stability of the nanocomposites with respect to pure starch matrix.