表面活性单体NaAMC14S/丙烯酰胺共聚物的分子链微结构与疏水缔合性

在实施丙烯酰胺型阴离子表面活性单体2-丙烯酰胺基十四烷磺酸钠(NaAMC14S)与丙烯酰胺(AM)水溶液均相共聚合过程中,分别通过改变AM与NaAMC14S的投料比、改变外加电解质NaCl的加入量以及引发剂的用量,制备了分子链微结构系列变化的具有微嵌段结构的共聚物NaAMC14S/AM;采用荧光探针法与表观粘度法研究了共聚物分子链微结构与其疏水缔合性能之间关系,探索了共聚物分子链中疏水微嵌段含量、疏水微嵌段长度及共聚物分子量诸微结构因数对共聚物疏水缔合性的影响.结果表明,共聚物NaAMC14S/AM的疏水缔合性随着疏水微嵌段含量的增加而增强,随着疏水微嵌段长度的增长而增强,当疏水微嵌段含量和嵌段长度一定时,共聚物的疏水缔合性随分子量的增大而增强.     

丙烯酰胺-苯乙烯双亲嵌段共聚物水溶液的表面活性及增溶性

在微乳液介质中制备了系列的丙烯酰胺 (AM)与苯乙烯 (St)的双亲嵌段共聚物 (PAM b PSt) ,用紫外分光光度法测定了共聚物的组成 ,用乌氏粘度计测定了共聚物的特性粘数 [η],并用其相对表征共聚物的分子量大小 .重点研究了双亲嵌段共聚物 (PAM b PSt)疏水链段在水溶液中的缔合行为、共聚物的表面活性及其对有机物的增溶性能 ,考察了共聚物分子组成 (疏水链段含量 )与分子量对其表面活性与增溶性能的影响规律 .研究结果表明 ,由于疏水链段的憎水性 ,PAM b PSt的分子链在水溶液表面会形成表面吸附 ,从而降低水溶液的表面张力 ;而在水溶液中 ,在疏水相互作用下 ,PAM b PSt分子链中的苯乙烯疏水链段会形成分子间或分子内的胶束 ,烃类有机物可增溶其中 ;疏水链段含量越大 ,分子量越小 ,PAM b PSt的表面活性与增溶性能越强     

丙烯酰胺-苯乙烯双亲嵌段共聚物水溶液的粘度性能

通过改变丙烯酰胺 (AM)与苯乙烯 (St)两单体的投料比 ,在微乳液介质中制备了分子组成系列变化的丙烯酰胺 苯乙烯双亲嵌段共聚物 (PAM b PSt) ,使用旋转粘度计测定了共聚物水溶液的表观粘度 ,详细考察了共聚物浓度、共聚物链结构、剪切速率、盐度及温度等因素对共聚物水溶液表观粘度的影响规律 .研究结果表明 ,由于PAM b PSt分子链中的PSt疏水嵌段链段之间具有强的疏水缔合作用 ,导致其具有独特的流变性能 .当共聚物水溶液的浓度高于某一临界值后 ,疏水缔合作用以分子间的缔合为主 ,大分子链之间会形成动态物理交联网络 ,增大了流体力学体积 ,使PAM b PSt水溶液可产生良好的增稠性能 ;疏水缔合作用是一吸热过程 ,升高温度有利于分子间的缔合 ,因此PAM b PSt水溶液具有良好的耐温性 ;聚合物水溶液中盐类物质的存在 ,会增强溶剂的极性 ,有利于分子间的缔合 ,使PAM b PSt水溶液具有良好的耐盐性 .     

丙烯酰胺型阴离子表面活性单体与丙烯酰胺共聚物水溶液的流变特性

以丙烯酰胺型阴离子表面活性单体2-丙烯酰胺基十四烷基磺酸钠(NaAMC14S)为共单体,与丙烯酰胺(AM)的水溶液均相共聚合,使NaAMC14S的浓度分别处于临界胶束浓度上下,分别制备了具有无规结构与微嵌段结构的两类共聚物;用红外光谱法对共聚物的结构进行了表征,使用乌氏粘度法测定了特性粘数,相对表示出了共聚物的分子量;采用荧光探针法与表观粘度法重点研究了两类共聚物的疏水缔合性与水溶液的流变特性.研究结果表明,具有微嵌段结构的共聚物具有很强的疏水缔合性,当其水溶液的浓度达0.2wt%后,表观粘度迅速提高;其水溶液的切力变稀行为具有明显的可逆性,表现出强的抗剪切性能.本研究中特别发现,具有微嵌段结构的共聚物其盐水溶液的表观粘度远高于纯水溶液的表观粘度,当共聚物浓度为0.3wt%、CaCl2浓度为2wt%时,溶液的表观粘度竟然提高了3个数量级,表现出独特的正性盐敏性(即遇盐变稠).     

兼具有强阴离子性与疏水缔合性的丙烯酰胺三元共聚物

在微乳液介质中实施了丙烯酰胺 (AM)、苯乙烯 (St)、2 丙烯酰胺基 2 甲基丙磺酸钠 (NaAMPS)的共聚合 ,制备了既含有强阴离子性基团 (—SO3Na)又含有疏水基团 (St)的丙烯酰胺三元共聚物AM NaAMPS St;通过红外光谱法、紫外分光光度法及元素分析法对共聚物的结构及组成进行了表征 ;稀释外推粘度法测定了共聚物的特性粘数 ;测定了共聚物纯水溶液及盐水溶液的表观粘度 ;荧光探针法考察了三元共聚物的疏水缔合性以及离子基团对疏水缔合性的影响规律 .实验结果表明 ,在聚丙烯酰胺 (PAM )分子主链上同时引入强阴离子性基团与疏水基团后 ,阴离子的电粘效应与疏水基团的疏水缔合作用相互协同 ,会使共聚物水溶液的黏度显著提高 ;盐溶液对疏水缔合作用的增强效应与强阴离子基团对盐的较大容忍度相互结合 ,会使共聚物水溶液的抗盐性能明显得以提高 ;大分子链上的强阴离子基团磺酸根的存在 ,在一定程度上会削弱疏水基团之间的疏水缔合作用 ,即对疏水基团的疏水缔合行为会产生一定的负性影响 .     

新一族疏水缔合聚丙烯酰胺NaAMC14S/AM与Gemini表面活性剂之间的相互作用

在水溶液中进行了表面活性单体丙烯酰胺基十四烷基磺酸钠(NaAMC14S)与丙烯酰胺(AM)的均相共聚合, 制备了具有微嵌段结构的疏水缔合聚丙烯酰胺NaAMC14S/AM, 合成了阳离子型Gemini表面活性剂二溴化-N,N′-二(二甲基十二烷基)己二铵(C12C6C12Br2), 采用表观粘度法和荧光探针法研究了共聚物NaAMC14S/AM与Gemini表面活性剂C12C6C12Br2的相互作用. 研究结果表明, 疏水缔合聚丙烯酰胺NaAMC14S/AM与Gemini表面活性剂C12C6C12Br2之间存在着很强的相互作用, 既存在静电相互作用, 又存在强烈的疏水相互作用, 表现在以下几方面: C12C6C12Br2的加入, 使共聚物NaAMC14S/AM在浓度小于其临界缔合浓度(cac)时即发生分子间的缔合; C12C6C12Br2在低于其临界胶束浓度时, 就与共聚物NaAMC14S/AM形成混合胶束; 当共聚物的浓度为0.30%(w)时, 随着C12C6C12Br2加入量的增多, 共聚物水溶液的粘度会发生大幅度的增加, 在最大值处粘度竟提高了3个数量级. 研究还发现, 共聚物NaAMC14S/AM与C12C6C12Br2之间的相互作用还与共聚物分子链中的疏水微嵌段含量有关, 疏水微嵌段含量越多, NaAMC14S/AM与C12C6C12Br2之间的相互作用越强, 溶液粘度增加的程度越大.     

新型疏水缔合丙烯酰胺/2-苯氧乙基丙烯酸酯共聚物的合成与性质

采用胶束共聚方法合成了一种新型的疏水缔合共聚物 ,它由丙烯酰胺 (AM)和少量的 2 苯氧乙基丙烯酸酯 (POEA) (<1 0mol% )组成 ,具有良好的水溶性 .当溶液浓度超过一定值c 后 ,由于分子间的疏水缔合 ,产生很大的增粘作用 .研究了不同聚合条件下包括单体浓度、投料比和SMR值对聚合物的结构和性能的影响 .实验结果表明 ,聚合物的粘度性质和缔合行为取决于其分子量的大小、疏水单体含量及其嵌段的长度和分布 .     

水溶性AM-St两亲嵌段共聚物的自乳化微乳液法合成

水溶性AM-St两亲嵌段共聚物的自乳化微乳液法合成;丙烯酰胺;苯乙烯;疏水缔合共聚物     

水溶性疏水缔合型聚(丙烯酰胺-丙烯酸十六酯)溶液性质的研究

采用沉淀聚合法制备水溶性的丙烯酰胺－丙烯酸十六疏水缔合型共聚物,研究了共聚物水溶液的性质及其影响因素。随着疏水基团含量增加,共聚物在纯水中及NaCl溶液中的特性粘数[η]均减小,疏水基团临界缔合浓度降低。共聚物溶液浓度高于监界缔合浓度时,溶液表现粘度急剧增加,表明溶液中分子间缔合大量形成。     

阳离子型共聚物AM/DMBAC疏水微嵌段结构的分析

利用表面张力法对甲基丙烯酰氧乙基二甲基苄基氯化铵(简称DMBAC)在水溶液中的表面活性进行了测试并确定了其CMC值.研究了丙烯酰胺(AM)和DMBAC在水溶液中的共聚合反应行为,测定了AM与DMBAC共聚反应的竞聚率;IR,1H-NMR对共聚物的结构进行了表征;13C-NMR和DSC分析了单体DMBAC浓度对共聚产物微结构的影响;芘作为荧光探针测定了共聚物水溶液的疏水缔合性质.实验结果表明当共聚单体DMBAC浓度大于CMC时DMBAC倾向于均聚,DMBAC在共聚产物主链上呈微嵌段的形式分布.当共聚单体DMBAC浓度小于CMC时,DMBAC与AM倾向于无规共聚.     

Studies on microstructure and aqueous solution properties of block copolymer of acrylamide-styrene

Three series of block copolymers of acrylamide (AM) and styrene (St) as hydrophobic comonomer with varied microstructures were prepared in microemulsion medium by changing feed ratio of monomers, ratio of St to surfactant, and amount of initiator, respectively. The effects of microstructure factors of the amphiphilic block copolymers PAM-b-PSt on their aqueous solution properties were investigated by fluorescence probe technique and surface tension measurement in detail. The experimental results show that the aqueous solution properties of PAM-b-PSt are strongly dependent on their microstructure factors, such as the length and content of PSt hydrophobic blocks in the copolymers and their molecular weight. It was found that the main microstructure factors which effect the hydrophobic association behavior of the copolymer PAM-b-PSt are the length and content of PSt hydrophobic blocks in the copolymer, whereas the hydrophobic association behavior of the copolymer is not affected nearly so much by molecular weight in more dilute regions. At the same time, it was also found that the main microstructure factors which affect the surface activity of the copolymer are the content of PSt hydrophobic blocks in the copolymer and molecular weight, whereas the length of PSt blocks in copolymer does not affect surface activity of the copolymer nearly so much under fixed content of PSt hydrophobic blocks and molecular weight in the copolymer.     

Synthesis of amphiphilic block copolymers with well‐defined glycopolymer segment by atom transfer radical polymerization

AB block copolymers of 2‐(2′,3′,4′,6′‐tetra‐O‐acetyl‐β‐D‐glucopyranosyloxy)ethyl acrylate (AcGEA) with styrene (St) have been synthesized by atom transfer radical polymerization using well‐defined bromo‐terminated polystyrene as a macroinitiator. An O‐deacetylation of the precursor copolymers affords amphiphilic block copolymers, PSt‐b‐PGEA, with well‐defined glycopolymer segments and narrow molecular weight distributions (M_w/M_n < 1.4). The examination of the aqueous solution of these amphiphilic block copolymers revealed the formation of ordered aggregates.     

Y‐shaped poly(ethylene glycol) and poly(trimethylene carbonate) amphiphilic copolymer: Synthesis and for drug delivery

New Y‐shaped (AB₂‐type) amphiphilic copolymers of poly(ethylene glycol) (PEG) with poly(trimethylene carbonate) (PTMC), PEG‐b‐(PTMC)₂, were successfully synthesized by the ring‐opening polymerization (ROP) of TMC with bishydroxy‐modified monomethoxy‐PEG (mPEG). First, a bishydroxy functional ROP initiator was synthesized by esterification of acryloyl bromide with mPEG, followed by Michael addition using excess diethanolamine. A series of Y‐shaped amphiphilic PEG‐(PTMC)₂ block copolymers were obtained via ROP of TMC using this PEG with bishydroxyl end groups as macroinitiator and ZnEt₂ as catalyst. The amphiphilic block copolymers with different compositions were characterized by gel permeation chromatography (GPC) and ¹H NMR, and their molecular weight was measured by GPC. The results showed that the molecular weight of Y‐shaped copolymers increased with the increase of the molar ratio of TMC to mPEG‐(OH)₂ initiator in feed while the PEG chain length was kept constant. The Y‐shaped copolymer mPEG‐(PTMC)₂ could self‐assemble into micelles in aqueous medium and the critical micelle concentration values of the micelles decrease with increase in hydrophobic PTMC block length of mPEG‐(PTMC)₂. The in vitro cytotoxicity and controlled drug release properties of the Y‐shaped amphiphilic block copolymers were also investigated. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8131–8140, 2008     

两亲嵌段共聚物胶束用作医用材料

两亲嵌段共聚物可以在水溶液中自组装形成亲水性链段为外壳、疏水性链段为内核的胶束,这种胶束能够用作药物载体而引起人们极大的关注。本文综述了两亲嵌段共聚物胶束用作医用材料的研究进展,主要内容包括医用两亲嵌段共聚物的种类,胶束化,以及用作诊断试剂载体、药物缓释载体、靶向载体等。两亲嵌段共聚物胶束用作磁共振造影剂载体有利于肿瘤的诊断,用作药物缓释载体可以有效增溶难溶性抗肿瘤药物,延长药物在体内的血液循环时间。此外,通过对胶束表面进行修饰或者施加外场,还可以实现靶向功能。因此,两亲嵌段共聚物胶束在医用材料领域有着广阔的发展前景。     

Organic/inorganic hybrid star-shaped block copolymers of poly(l-lactide) and poly(N-isopropylacrylamide) with a polyhedral oligomeric silsesquioxane core: Synthesis and self-assembly

The star-shaped organic/inorganic hybrid poly(l-lactide) (PLLA) based on polyhedral oligomeric silsesquioxane (POSS) was prepared using octa(3-hydroxypropyl) polyhedral oligomeric silsesquioxane as initiator via ring-opening polymerization (ROP) of l-lactide (LLA). The molecular weight of POSS-containing star-shaped hybrid PLLA (POSSPLLA) can be well controlled by the feed ratio of LLA to initiator. The POSSPLLA was further functionalized into the macromolecular reversible addition-fragmentation transfer (RAFT) agent for the polymerization of N-isopropylacrylamide (NIPAM), leading to the POSS-containing star-shaped organic/inorganic hybrid amphiphilic block copolymers, poly(l-lactide)–block–poly(N-isopropylacrylamide) (POSS(PLLA–b–PNIPAM)). The self-assembly behavior of POSS(PLLA–b–PNIPAM) block copolymers in aqueous solution was investigated by dynamic light scattering (DLS), transmission electron microscopy (TEM) and atomic force microscopy (AFM). DLS showed the PNIPAM block in the aggregates is temperature-responsive and its phase-transition is reversible. TEM proved that the star-shaped POSS(PLLA–b–PNIPAM) amphiphilic block copolymers can self-assemble into the vesicles in aqueous solution. The vesicular wall and coronas are composed of the hydrophobic POSS core and PLLA, and hydrophilic PNIPAM blocks, respectively. Therefore, POSSPLLA and POSS(PLLA–b–PNIPAM) block copolymers, as a class of novel organic–inorganic hybrid materials with the advantageous properties, can be potentially used in biological and medical fields.     

Solvent replacement to thermo‐responsive nanoparticles from long‐subchain hyperbranched PSt grafted with PNIPAM for encapsulation

Long‐subchain hyperbranched polystyrene (lsc‐hp PSt) with uniform subchain length was obtained through copper‐catalyzed azide‐alkyne cycloaddition click chemistry from seesaw macromonomer of PSt having one alkynyl group anchored at the chain centre and two azido group attached to both chain ends [alkynyl‐(PSt‐N₃)₂]. After precipitation fraction, different portions of lsc‐hp PSt having narrow overall molecular weight distribution were obtained for further grafting with alkynyl‐capped poly(N‐isopropylacrylamide) (alkynyl‐PNIPAM), which was obtained via single‐electron transfer living radical polymerization of NIPAM with propargyl 2‐bromoisobutyrate as the initiator and grafted onto the peripheral azido groups of lsc‐hp PSt via click chemistry. Thus, amphiphilic lsc‐hp PSt grafted with PNIPAM chains (lsc‐hp PSt‐g‐PNIPAM) was obtained and would have star‐like conformation in tetrahydrofuran (THF). By replacing THF with water, lsc‐hp PSt‐g‐PNIPAM was dissolved at molecular level in aqueous solution due to the hydrophilicity of PNIPAM and exhibited thermal induced shrinkage of PNIPAM arms. The water‐insoluble lsc‐hp PSt would collapse densely and could be served as a reservoir to absorb hydrophobic chemicals in aqueous solution. The influence of overall molecular weight of lsc‐hp PSt on the absorption of pyrene was studied. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

ABA型两亲嵌段共聚物的合成及表征

以α ,α′ 二溴代二甲苯为引发剂 ,CuBr/2 ,2′ 联吡啶为催化体系 ,制备了双溴端基的分子量分布窄的聚苯乙烯 (MWD =1 18) .再以此作为大分子引发剂 ,实现了甲基丙烯酸对硝基苯酯的原子转移自由基聚合 ,制得了分子量可控且分子量分布窄的ABA型嵌段共聚物 ,再经水解、酸化 ,得到了聚甲基丙烯酸 b 聚苯乙烯 b 聚甲基丙烯酸ABA型两亲嵌段共聚物