Low infrared emissivity of polyurethane/Cu composite coatings

Polyurethane/Cu composite coatings with low infrared emissivity near to 0.10 at the wavelength of 8-14 μm were prepared by a simple and convenient process. The influences of the content of Cu powder, surface roughness, coating thickness and temperature on infrared emissivity of the coatings were systematically investigated. The results indicated that the emissivity decreases significantly with increasing content of Cu powder and coating thickness. The coatings with smooth surface exhibit lower emissivity values than those with rough coatings. Moreover, we found the relationship between the emissivity of coatings and temperature presents a “U” type, and the emissivity reaches to the minimum at about 380 K. The mechanisms of low emissivity were proposed by optical theories, which are found to be in a good agreement with the experimental results.     

Microstructure and infrared emissivity property of coating containing TiO2 formed on titanium alloy by microarc oxidation

Ceramic coatings containing TiO₂ were formed on Ti6Al2Zr1Mo1V alloy surface by microarc oxidation (MAO) method. The microstructure, phase and chemical composition of the coatings were analyzed by SEM, XRD and EDS techniques. The coating mainly consists of rutile TiO₂ and a small amount of anatase TiO₂. The infrared emissivity values of coated and uncoated titanium samples when exposed to 700 °C were tested. It was found that the coating exhibits a higher infrared emissivity value (about 0.9) in the wavelength range of 8–14 μm than that of the uncoated titanium alloy, although which shows a slight increase from 0.1 to 0.3 with increasing exposure time at 700 °C. The relatively high infrared emissivity value of the MAO coating is possibly attributed to the photon emission from the as formed TiO₂ phase.     

直接置换法制备包覆型纳米铜-银双金属粉末

 以AgNO₃为主盐,采用直接置换法初步制备了包覆型纳米铜-银双金属粉末,分析了工艺条件对包覆效果的影响,并用透射电子显微镜、X射线能量色散谱仪和X射线衍射仪进行了表征。实验结果表明：纳米铜-银双金属粉末为包覆型结构,平均粒径约70 nm,分散性较好,表面银的原子分数达到74.28%。在洗涤过程中加入一定量的保护剂,有效解决了纳米铜粉的氧化问题。     

Electroless Ni-P coating preparation of conductive mica powder by a modified activation process

A modified activation process was developed for electroless Ni-P coating preparation of conductive mica powder. The electroless Ni-P coating process was modified by replacing the conventional sensitization and activation steps only using activation step with a Pd(II)-APTHS activator, which is a complex of Pd(II) ion with a derivate γ-aminopropyltrihydroxysilane (APTHS) from the hydrolysis of γ-aminopropyltriethoxysilane (APTES). The activated reaction progress and resulted Ni-P coating were characterized by XPS, SEM/EDX and TEM. Electroless nickel deposition was successfully initiated by this activation process. This activation process is very simple, and the obtained Ni-P deposits have the advantages of uniformity, continuity and densification. The average specific resistivity for the Ni-P coated mica powder was 4.85 × 10⁻² Ω cm.     

Microwave absorption properties of a wave-absorbing coating employing carbonyl-iron powder and carbon black

To prevent serious electromagnetic interference, a single-layer wave-absorbing coating employing complex absorbents composed of carbonyl-iron powder (CIP) and carbon black (CB) with epoxy resin as matrix was prepared. The morphologies of CIP and CB were characterized by scanning electron microscope (SEM) and transmission electron microscope (TEM), respectively. The electromagnetic parameters of CIP and CB were measured in the frequency range of 2-18 GHz by transmission/reflection technology, and the electromagnetic loss mechanisms of the two particles were discussed, respectively. The microwave absorption properties of the coatings were investigated by measuring reflection loss (RL) using arch method. The effects of CIP ratio, CB content and thickness on the microwave absorption properties were discussed, respectively. The results showed that the higher thickness, CIP or CB content could make the absorption band shift towards the lower frequency range. Significantly, the wave-absorbing coating could be applied in different frequency ranges according to actual demand by controlling the content of CIP or CB in composites.     

Preparation and characterization by infrared emission spectroscopy and applications of new mineral-based composite materials of biomedical interest

New composite materials based on clay minerals had been prepared by reductive calcination. These materials exhibit very strong infrared (IR) emission at quite low temperatures. The structural properties and emission capabilities of the new materials have been studied by various theoretical and experimental methods. In addition, a brief overview of the medical and other practical applications of IR-emitting materials is presented. The basic principles of IR emission spectroscopy are discussed with special respect to low temperatures (close to human-body temperature). Furthermore, DFT calculations on a kaolinite structure of chemical composition of [Al₄Si₄ O₈(OH)₁₆]^4? have been performed. The calculated bond distances and IR spectrum are in good agreement with experimental observations. Structural and compositional characterization of the new composite materials have been performed by various structural analytical methods. An interesting effect on the IR phosphorescence of composite samples has been established. After 2 hours of IR light exposure at room temperature from the FT-IR spectrometer, the composite materials exhibited enhanced emission of IR radiation with relaxation time about 40 min. Finally, two practical applications of the composites have been investigated, namely polyamide-based fabrics and rubber preservatives.     

Attenuation of solar radiation by a water mist from the ultraviolet to the infrared range

A model is developed for the hemispherical transmittance of direct and scattered solar radiation from a cloudless atmosphere by a mist layer of water droplets in order to investigate the potential of water misting systems to serve as a protection from solar irradiation with particular emphasis on harmful UV radiation. The proposed model is based on published spectral experimental data for solar irradiation, Mie theory for interaction of the radiation with single spherical droplets, and radiative transfer theory. Known limiting solutions are employed to simplify the Mie calculations. The modified two-flux approximation is used to account for both direct and diffuse irradiation in lieu of a numerical solution for the full radiative transfer equation in anisotropically scattering media. The role of the governing parameters of a disperse water curtain of water droplets, water content, and droplet size for sample conditions is studied in some detail, particularly in the near-ultraviolet part of the spectrum where radiation can result in human tissue damage.     

快电子发散角的实验测量

采用飞秒激光辐照铜靶,利用电子角分布仪和LiF热释光探测器测量了快电子发射的发散角.实验结果显示,快电子的发散角与激光入射角密切相关,随着激光入射角增加,快电子的发散角逐渐减小.在相同入射角条件下,加上预脉冲将导致快电子的发散角变小.这个结果为获取较小发散角的快电子束提供了实验参考.     

Preparation of a novel Ni/Co-based alloy gradient coating on surface of the crystallizer copper alloy by laser

A high wear-resistant gradient coating made of Ni/Co-based alloys on the surface of a Cu alloy substrate was synthesized using a YAG laser induced in situ reaction method. The coating consists of three layers: the first is a Ni-based alloy layer, the second and third are Co-based alloy layers. The microhardness increases gradually from 98 HV in the Cu alloy substrate to the highest level of 876 HV in the third layer. The main phase of the Co-based alloy layer is CoCr₂(Ni,O)₄, coexisting with the Fe₁₃Mo₂B₅, Cr(Co(Mo, and FeCr_0.29Ni_0.16C_0.06 phases. Wear tests indicate that the gradient coating has good bond strength and wear properties with a wear coefficient of 0.31 (0.50 for the Cu alloy substrate). Also, the wear loss of the coating is only 0.01 g after it has been abraded for 60 min, which is only one fifth of that of the Cu alloy of the crystallizer. Wear tests of the gradient coating reveal good adhesive friction and wear properties when sliding against steel under dry conditions. This novel technique may have good application to make an advanced coating on the surface of the Cu alloy crystallizer in a continuous casting process.     

Experimental and theoretical insight into the cooperativity effect in composite wax powder and ternary complex of coronene with CH4 and Mn+ (Mn+ = Li+, Na+, K+, Be2+, Mg2+ or Ca2+)

The experimental infrared (IR) spectrum of composite wax powder was investigated. The frequency shifts of the C=C anti-symmetrical stretching mode were observed and the experimental cooperativity effect involving Na⁺···π interaction was suggested. In order to further reveal the nature of cooperativity effect, the interaction energies in Mⁿ⁺···coronene···CH₄ (Mⁿ⁺ = Li⁺, Na⁺, K⁺, Be²⁺, Mg²⁺ or Ca²⁺) as the model systems of composite wax powder were calculated by using the B3LYP, M06-2X and MP2 methods with 6-311++G^** basis set. The results show that the Mⁿ⁺···π interactions were strengthened upon the formation of ternary complexes. Although the changes of absolute values of the interactions between CH₄ and coronene were not obvious, the relative values were considerably significant upon the formation of ternary complexes. The cooperativity effect was perhaps the reason for the formation of notable advantage of composite wax powder upon the introduction of surfactant with cation into wax powder. Reduced density gradient and atoms-in-molecules analysis confirm the cooperativity effect in Mⁿ⁺···coronene···CH₄, and reveal the nature of the formation of the predominant advantage of composite wax powder.     

Ni-Al layered double hydroxides modified with citrate, malate, and tartrate: Preparation by coprecipitation and uptake of Cu from aqueous solution

We report on aqueous Cu²⁺ uptake by Ni-Al layered double hydroxides (Ni-Al LDHs) modified with citrate (C₆H₅O₇³⁻), malate (C₄H₄O₅²⁻), and tartrate (C₄H₄O₆²⁻) anions via coprecipitation. Dropwise addition of a mixed aqueous solution of Ni(NO₃)₂ and Al(NO₃)₃ to the respective organic acid solutions at a constant pH of 7.0-9.0 afforded LDHs with intercalated C₆H₅O₇³⁻ and Ni(C₆H₅O₇⁾⁻, C₄H₄O₅²⁻, and C₄H₄O₆²⁻ in their interlayers. The anions were also likely adsorbed on the LDH surface. Citrate·Ni-Al LDH could rapidly take up Cu²⁺ at a constant pH of 5.0, mainly via chelation by the intercalated and adsorbed anions, rather than coprecipitation with dissolved Al³⁺ to form Cu-Al LDH. By contrast, malate and tartrate were not active as chelating agents, probably because they formed bridges between brucite-like layers by direct coordination of the two −COO⁻ groups with Al³⁺ in those layers.     

A Ftir and Raman Spectral Study of the Preparation of Lead Titanate (PbTiO3) by a Sol-Gel Method

Lead Titanate (FT) materials were prepared by a sol-gel process in an air atmosphere using lead acetate and titanium propoxide in methoxyethanol as the precursor materials. FTIR and Raman spectroscopy were used to characterize the various structural changes that occurred during various stages of the preparation. A new crystalline lead titanate phase was detected by both Raman spectral and X-ray diffraction techniques when heating the gelled material at 430°C. In-situ Raman spectra were measured at high temperatures for the resulting sol-gel prepared PT material to investigate its phase-transition and soft-mode behavior.     

Preparation and characterization of Cu(In,Ga)(Se,S)2 films without selenization by co-sputtering from Cu(In,Ga)Se2 quaternary and In2S3 targets

In this study, Cu(In,Ga)(Se,S)₂ (CIGSS) thin films were deposited onto a bi-layer Mo coated soda-lime glass by co-sputtering a chalcopyrite Cu(In,Ga)Se₂ (CIGS) quaternary alloy target and an In₂S₃ binary target. A one-stage annealing process was performed to form CIGSS chalcopyrite phase without post-selenization. Experimental results show that CIGSS films were prepared by the proposed co-sputter process via CIGS (70 W by radio frequency) and In₂S₃ (30 W by direct current) with a substrate temperature of 373 K, working pressure of 0.67 Pa, and one-stage annealing at 798 K for 30 min. The stoichiometry ratios of the CIGSS film were Cu/(In + Ga) = 0.92, Ga/(In + Ga) = 0.26, and Se/(S) = 0.49 that approached device-quality stoichiometry ratio (Cu/(In + Ga) < 0.95, Ga/(In + Ga) < 0.3, and (Se/S) ≈ 0.5). The resistivity of the sample was 14.8 Ω cm, with a carrier concentration of 3.4 × 10¹⁷ cm⁻³ and mobility of 1.2 cm² V⁻¹ s⁻¹. The resulting film exhibited p-type conductivity with a double graded band-gap structure.     

Preparation of organic acid anion-modified magnesium hydroxides by coprecipitation: A novel material for the uptake of heavy metal ions from aqueous solutions

New layered magnesium hydroxides whose brucite layers had been bridged with malate²⁻ and tartrate²⁻ were prepared by dropwise addition of Mg(NO₃)₂ to malate and tartrate solutions at a constant pH of 10.5. Malate²⁻ and tartrate²⁻ may have been also absorbed on the surfaces of hydroxides. In the case of using citrate solution, Mg(OH)₂ absorbed with citrate³⁻ was produced. These materials were found to take up Cu²⁺ rapidly from an aqueous solution at pH 5.0. Copper uptake by precipitates is attributed to the formation of chelate complexes of Cu²⁺ with citrate³⁻, malate²⁻, and tartrate²⁻.     

The model updating based on near infrared spectroscopy for the sex identification of silkworm pupae from different varieties by a semi-supervised learning with pre-labeling method

Abstract

It is effective to accurately discriminate the sex of silkworm pupae with the same varieties based on near infrared spectroscopy. However, when the model is promoted to classify new varieties of silkworm pupae, the model’s performance becomes worse, due to the cultivation environment and varieties changing. In the aims of improving the generalization ability and accuracy of the model, this paper proposed a model updating strategy based on semi-supervised learning. First, support vector machine identification model was built after the original spectra was pretreated by Savitzky-Golay convolution smoothing operation, which could effectively reduce spectra noise. Then, the support vector machine model gave the pre-labelings of unlabeled silkworm pupae in the updated set, which were divided into male samples and female samples. According to the correlation coefficients that calculated by Pearson correlation coefficient and Euclidean distance, a total of 8 reliable samples were selected from the male and female samples, respectively. The reliable samples were added to the original training set to update the original model. Finally, the updated model was used to test the test sets from the varieties of silkworm pupae that were the same with updated sets.The results showed the performance of the non-updated model for silkworm pupae from the three new varieties just reached 54.55%, 68.52%, 86.84%, respectively. The support vector machine model updated by using Pearson correlation coefficient improved the accuracy to 100%, 96.30%, 97.37%, and the model updated by Euclidean distance increased the identification accuracy of the three varieties that were not involved in the modeling to 100%, 75.93%, 92.10% respectively. The results showed that the performance of the model updated by Pearson correlation coefficient was better than Euclidean distance. The results revealed that the method based on semi-supervised learning could effectively solve the problem of poor universality for sex identification model.     

Raman analysis assessed by Fourier‐Transformed infrared and X‐ray fluorescence spectroscopies: a multi‐analytical approach of ancient chromolithographs from the 19th century

A set of chromolithographs from the 19th century were analysed to identify the fillers and pigments used for their elaboration. Because of the delicacy of the chromolithographs, the research involved the use of Raman, Fourier‐transform infrared and energy dispersive X‐ray fluorescence spectroscopies for a complete characterization of the works on paper without removing any microsamples. Despite the high fluorescence of the samples when analyzed by Raman spectroscopy, in this paper, we demonstrated that ink spectra can be successfully enhanced by subtracting the spectra of the supporting background paper. The results of the study showed that, apparently, the lithographer used a limited range of common inorganic pigments from the 19th century (carbon black, chrome yellow, Prussian blue, red ochre, red lead and vermilion) together with organic pigments (indigo blue, gamboge and a red organic pigment). The study also found that despite the fact that during the 19th and early 20th century the use of mixtures of several pigments was a common practice, unusual admixtures were used for the preparation of some colours of the studied chromolithographs. Copyright © 2011 John Wiley & Sons, Ltd.     

Preparation of Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> nanowires by calcining the precursor powders synthesized in a novel inverse microemulsion

Manganese oxide (hausmannite) nanowires were prepared by annealing precursor powders at a temperature of 800 °C for 3 h, which were produced in a novel inverse microemulsion (IμE) system. The microstructures of the as-prepared Mn₃O₄ nanowires were investigated by means of X-ray diffraction, transmission electron microscopy, and Raman spectra. It has been found that the Mn₃O₄ nanowires were relatively straight and their surfaces were smooth with a typical diameter of 75–150 nm. The formation mechanism of the Mn₃O₄ nanowires is discussed. Received: 30 May 2002 / Accepted: 7 October 2002 / Published online: 17 December 2002 RID="*" ID="*"Corresponding author. Fax: +86-25/359-5535, E-mail: wangqun@nju.edu.cn