TiO2-Al2O3载体的制备方法对其负载的磷化镍催化剂加氢脱氮反应性能的影响

采用共沉淀法和原位溶胶-凝胶法制备了TiO₂-Al₂O₃复合载体,其负载的磷化镍催化剂采用等体积浸渍法和H₂原位还原法制备. 通过N₂吸附（BET）、X射线衍射（XRD）、透射电镜（TEM）、程序升温还原（TPR）,X射线光电子能谱（XPS）和等离子体发射光谱（ICP-AES）表征技术对催化剂进行了表征,并通过喹啉的加氢脱氮反应评价了催化剂的加氢脱氮性能. 结果表明,原位溶胶-凝胶法制成的复合载体基本保留了原有的γ-Al₂O₃的孔特征,具有较大的比表面积和较宽的孔分布,TiO₂主要以表面富集的形式分散在管状的γ-Al₂O₃表面,其负载的磷化镍催化剂还原后所形成的活性相为Ni₂P和Ni₁₂P₅;而共沉淀法制成的复合载体比表面积较小,孔径分布更加集中,TiO₂趋于在块状的Al₂O₃表面均匀分散,其负载的磷化镍催化剂具有更好的可还原性,还原后所形成的活性相为Ni₂P. 不同的载体制备方法和不同的钛铝比对催化剂加氢脱氮性能影响较大,当n（Ti）/n（Al）=1/8时,共沉淀法载体负载的催化剂表现出最佳的加氢脱氮性能,在340 ℃,3 MPa,氢油体积比500,液时空速3 h^-1的反应条件下,喹啉的脱氮率可以达到91.3%.     

Sol-gel preparation of In2O3-Al2O3 supports with controlled textural and structural properties

Alumina supports with a very narrow pore size distribution were obtained with indium-doped alumina prepared by the sol-gel method. The formation of aluminum in pentahedral coordination was identified by ²⁷Al NMR-MAS-spectroscopy. A good correlation was obtained with the Al^V NMR-MAS intensity signal and the activity in isopropanol dehydration. The insertion of In³⁺ substituting some Al³⁺ in the alumina network was suggested.     

Li2O-Al2O3-GeO2-P2O5微晶玻璃的微观结构和离子电导率

采用传统熔体冷却法制备了Li3-xAl2-xGex(PO4)3(x=1.1~1.9)体系玻璃,并通过热处理工艺获得了高电导率的微晶玻璃。通过XRD、TEM和交流阻抗等测试方法,研究了该系微晶玻璃的物相组成、微观形貌和锂离子电导率。结果表明:该系统微晶玻璃析出导电主晶相为LiGe2(PO4)3,杂质相为AlPO4和GeO2。当x=1.5时,由于导电主晶相LiGe2(PO4)3晶粒充分长大、分布均匀,所制备微晶玻璃的室温锂离子电导率最高(5.72×10-4 S.cm-1),可以满足全固态锂离子电池对电解质高室温电导率的要求。     

固体碱催化剂K_2CO_3/Al_2O_3的制备及其催化餐饮废油制生物柴油的性能

采用浸渍法制备了K2CO3/Al2O3固体碱催化剂,考察了活性组分负载量、焙烧温度、焙烧时间等制备条件对催化剂在催化餐饮废油合成生物柴油的酯交换反应中催化活性的影响,并对其进行了FT-IR、XRD、TG-DTG、SEM和BET表征分析。实验结果表明,所制备的催化剂在催化餐饮废油合成生物柴油的酯交换反应中表现出良好的活性,在活性组分K2CO3负载量为50%、焙烧温度500℃、焙烧时间3 h的条件下制备的催化剂催化酯交换反应时,生物柴油产率可达86.70%。催化剂表征结果显示,K2CO3/Al2O3催化活性是因K2CO3与Al2O3经高温焙烧产生新的晶相有关。催化剂重复使用4次,生物柴油产率仍在75%以上。制得的生物柴油产品质量达到国家生物柴油B100标准。     

Al2O3-CeO2复合电解质的制备及其半导体离子燃料电池性能

通过共沉淀法制备了Al₂O₃-CeO₂复合材料,并将其作为电解质应用于半导体离子燃料电池(SIFC)。探究了Al₂O₃、CeO₂物质的量之比不同的Al₂O₃-CeO₂复合电解质对SIFC电化学性能的影响。采用X射线衍射(XRD)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)对材料进行了表征。其中,Al₂O₃、CeO₂物质的量之比为1∶0.5的Al₂O₃-CeO₂ (1∶0.5)电池获得了最佳性能,在550 ℃下,开路电压为1.099 V时最大功率密度为1 142 mW·cm^-2。得益于复合电解质在测试气氛下两相间的界面效应,Al₂O₃-CeO₂ (1∶0.5)电池在较低测试温度下取得了优异的混合离子传导和功率输出性能。     

Al2O3-CeO2复合电解质的制备及其半导体离子燃料电池性能

通过共沉淀法制备了Al₂O₃-CeO₂复合材料,并将其作为电解质应用于半导体离子燃料电池（SIFC）。探究了Al₂O₃、CeO₂物质的量之比不同的Al₂O₃-CeO₂复合电解质对SIFC电化学性能的影响。采用X射线衍射（XRD）、X射线光电子能谱（XPS）、扫描电子显微镜（SEM）和透射电子显微镜（TEM）对材料进行了表征。其中,Al₂O₃、CeO₂物质的量之比为1：0.5的Al₂O₃-CeO₂（1：0.5）电池获得了最佳性能,在550℃下,开路电压为1.099 V时最大功率密度为1 142 mW·cm^-2。得益于复合电解质在测试气氛下两相间的界面效应,Al₂O₃-CeO₂（1：0.5）电池在较低测试温度下取得了优异的混合离子传导和功率输出性能。     

Preparation and properties of homogeneous V2O5-SiO2 xerogel composite based on interpenetrating polymer network

In this paper, we report the conducting and electrochemical properties of a homogeneous V₂O₅-SiO₂ xerogel composite obtained from the simultaneous polymerization in both inorganic components (Si-O and V-O based polymers) forming an interpenetrating polymer network, where a mutual “solubility” due to cross-links and entanglements was observed. The presence of V₂O₅ inside the silica matrix has a strong effect on electrical conductivity; measurements showed room temperature conductivity almost 1000 times higher than what is found in the literature. In addition, the electrochemical behavior is quite similar to that found in V₂O₅ xerogel. Moreover, the effects of thermal treatment on the conducting and electrochemical properties were investigated. It was found that both properties were improved with no significant effect on V₂O₅ xerogel layered structure.     

CaO-SiO2-Al2O3-MgO-TiOx-FeOy体系氧化动力学

用电动势和化学分析方法研究了富钛还原熔渣－ＣａＯ－ＳｉＯ２－Ａｌ２Ｏ３－ＭｇＯ－ＴｉＯ２－ＦｅＯｙ体系的氧化动力学,得出了氧在熔渣中的扩散速率常数分别为０．６６＊１０＾－５ｍ．ｓ＾－１和１．９８＊１０＾－５ｍ．ｓ＾－１,研究表明：固体电解质构成的氧浓差电池法得出的结果不仅可靠,且方法快速,简便。     

Synthesis and characterization of sodium titanates Na2Ti3O7 and Na2Ti6O13

Na₂Ti₃O₇ and Na₂Ti₆O₁₃ were synthesized by sol-gel method in order to obtain pure phases. Different heat-treatments were applied on powders and pellets of these materials. The effects were studied by XRD, dilatometry, TGA-DTA, SEM and electrochemical impedance spectroscopy. Pure Na₂Ti₃O₇ was obtained at 973 K. Sintering at 1373 K caused a partial decomposition into Na₂Ti₆O₁₃. The Na₂Ti₃O₇ powder sintered at 1273 K showed polygonal microstructure. Na₂Ti₃O₇ pellets sintered at 1323 K for 10 h exhibited large structures. This latter microstructure decreased the electrical conductivity of Na₂Ti₃O₇. Pure Na₂Ti₆O₁₃ was obtained at 873 K. Sintering at 1073 K caused a partial decomposition into TiO₂ (rutile). Na₂Ti₆O₁₃ pellets sintered at 1323 K for 10 h exhibited common shrinkage behavior. This shrinkage process increased the electrical conductivity of this material. The presence of TiO₂ resulted in a oxygen partial pressure dependence of the electrical conductivity.     

Methane conversion to C2 hydrocarbons in solid electrolyte membrane reactors

Solid electrolyte membrane reactors (SEMRs) have been used to both study and influence catalytic reaction rates. Methane coupling is the reaction most thoroughly and intensively studied in these membrane reactors. In the last 20 years, oxygen ion (O²⁻), proton (H⁺) and mixed (O²⁻-e⁻, H⁺-e⁻) conducting membranes have been tested in order to maximize the conversion of methane to C₂ compounds. The present review contains the fundamental operating principles of the various SEMR types and their applications in this reaction. The difficulties that should be overcome in order to promote this SEMR process to an industrial scale are discussed.     

Sol-gel derived (LiCl)2-Al2O3-SiO2 thin film solid electrolyte

(LiCl)₂-Al₂O₃-SiO₂ thin film solid electrolyte was prepared by a sol-gel process with a spin coating technique. The thin film was studied by X-ray photoelectron spectroscopy (XPS) and ac impedance. The ionic conductivity of the solid electrolyte film is comparable to that of the bulk xerogel. The highest conductivity measured by ac impedance is 2.5×10^–4 S·cm^–1 at 300°C with E_a=0.75 eV.     

TiO_2-Al_2O_3复合载体的制备及Co-Mo/TiO_2-Al_2O_3催化剂加氢脱硫性能的研究

通过改进的溶胶-凝胶法(SG)、共沉淀法(CP)、表面沉淀法(PR)及混捏法(ME)制备TiO_2-Al_2O_3复合载体,考察了不同制备方法对复合载体物理性质的影响。采用浸渍法制备Co-Mo/TiO_2-Al_2O_3-X加氢脱硫催化剂,研究了Co-Mo/TiO_2-Al_2O_3-X加氢脱硫催化剂的脱硫性能。利用XRD、BET、SEM等表征手段对复合载体及催化剂进行表征分析。结果表明,SG法制备的复合载体粒径均一,具有较大的比表面积、孔径和孔体积;CP法制备复合载体时TiO_2以单层或亚单层的分散状态高度分散于γ-Al_2O_3中。在氢气压力3.0 MPa、反应温度280℃、反应时间4 h、液时空速1.4 h-1和氢油比600的条件下,SG法制备的Co-Mo/TiO_2-Al_2O_3催化剂具有较高加氢脱硫活性,噻吩转化率达到96.6%。     

磁性固体超强酸SO42-/ZrO2-Al2O3-Fe3O4的制备与性能研究

利用化学共沉淀法将磁性基质与固体酸组装制备磁性纳米固体超强酸催化剂，利用XRD、Raman、TG-DSC、M?ssbauer、TEM、HRTEM等手段对样品性质进行表征。结果表明：磁性基质的引入赋予固体超强酸以超顺磁性；Fe₃O₄、Al₂O₃粒子弥散在ZrO₂基质中，烧结过程中阻碍了扩散传质的进行以及晶界移动，抑制了ZrO₂晶体生长，稳定了四方晶相(T-ZrO₂)；样品粒径分布集中，平均约为32 nm；HRTEM显示T-ZrO₂晶体生长取向于(101)方向，晶面间距d(101)=0.29 nm；Hammett指示剂法测得经600 ℃焙烧后产物的酸强度H_o＜-13.8，酸强度大于浓硫酸(H_o=-11.93)。以柠檬酸三丁酯的合成作为磁性固体超强酸SO₄^2-/ZrO₂-Al₂O₃-Fe₃O₄催化剂的探针反应，结果表明外磁场的引入提高了柠檬酸的转化率。     

Preparation, characterization and application of KNH2/Al2O3 and KF/Al2O3 as strong solid bases

This review describes the preparation, characterization and application of KNH₂ loaded on alumina and KF loaded on alumina. These strong solid bases catalyze a variety of organic reactions in a very selective manner. The reactions include isomerizations of alkenes and alkynes, dimerization of alkynes, Tishchenko reaction, and the reaction of silanes to form of Si–C, Si–N and Si–O bonds.     

Preparation of COF2 using CO2 and F2 in the electrochemical cell with PbSnF4 as a solid electrolyte

Tetragonal PbSnF₄ was prepared by precipitation method with Pb(NO₃)₂ and SnF₂ aqueous solutions. The product was characterized using X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XFS), and the other chemical analyses. Tetragonal PbSnF₄ exhibited the highest electric conductivity of 3.2 Sm⁻¹ at 473 K in air as a fluoride ion conductor. We have investigated the possibility of COF₂ formation using CO₂ and F₂ in an electrochemical cell with PbSnF₄ as a solid electrolyte. At same time, we tried to produce an electric power from an electrochemical cell. This CO₂/F₂ electrochemical cell was constructed with a tetragonal PbSnF₄ disk having Au electrodes. The electromotive force was about 0.9 V at room temperature for 0.1 MPa CO₂/(0.01 MPa F₂ + 0.09 MPa Ar). However, the short circuit current density was 0.24 A m⁻², which was quite small. This current density was so small that no fluorocarbon compound was detected after 3 h discharge using FT-IR.     

Fe2O3/Al2O3氧载体用于甲烷化学链燃烧：负载量与制备方法的影响

以不同方法制备了系列Fe₂O₃/Al₂O₃氧载体,采用XRD、H₂-TPR、CH₄-TPR、O₂-TPD和BET等分析技术对氧载体进行了表征。研究了不同Fe₂O₃负载量氧载体的甲烷化学链燃烧性能,考察了不同制备方法对Fe₂O₃/Al₂O₃氧载体结构、反应性和产物选择性的影响。结果表明,Fe₂O₃负载量对氧载体活性及产物中CO₂选择性的影响较大,负载量较低时氧载体活性较低且引起甲烷部分氧化产物CO含量增加。制备方法亦对氧载体与甲烷的反应活性有所影响,整体上共沉淀法制备的质量分数60％Fe₂O₃/Al₂O₃氧载体具有较高的氧化活性和化学链循环稳定性。其在反应温度850℃、反应时间15 min、30次循环后甲烷转化率及产物中CO₂选择性均未见明显降低。     

Preparation of crack-free ZrO2 membrane on Al2O3 support with ZrO2–Al2O3 composite intermediate layers

To develop porous alumina supported MF ZrO₂ membranes, ZrO₂–Al₂O₃ composite intermediate layers are considered in order to decrease stress creation during the processing and avoid cracks formation. The relation between distortion stress and sintering shrinkage was experimentally studied. And the cracks formation mechanism was qualitatively evaluated and discussed. Finally, crack-free YSZ membrane with pore size of 0.16 μm on the two ZrO₂–Al₂O₃ intermediate layers possessing a gradient composition was successfully prepared and characterized.     

Hierarchically porous Fe2O3/CuO composite monoliths: Synthesis and characterization

In this paper, hierarchically porous Fe2O3/CuO composite monoliths were first successfully synthesized by a mild method using silica monoliths as templates. The structure of composite monoliths was characterized by X-ray diffraction, scanning electron microscopy, nitrogen adsorption-desorption. The results indicated that the molar ratio of Fe to Cu had a great influence on the crystal phase of Fe2O3, pore size and the structure of the macroporous wall. The Fe2O3/CuO composite monoliths consist of hierarchically macroporous and mesoporous structure, while the sample with the Fe/Cu molar ratio of 2 : 1 possesses tighter wall structure than other samples. It is expected that as-prepared Fe2O3/CuO composite monoliths have potential applications in several fields as catalysts, catalyst supports, chemical sensors and high-performance liquid chromatography (HPLC).     

添加Y2O3的ZrO2—Al2O3复相陶瓷力学性能的研究

采用工业ZrO2, Al2O3原料, 以Y2O3作为稳定剂, 通过适当的工艺制备出ZrO2-Al2O3复相陶瓷. 研究结果表明, Y2O3添加量为3.5%(摩尔分数)的ZrO2基陶瓷中加入Al2O3可有效地抑制ZrO2晶粒的生长, 有利于使ZrO2晶粒以亚稳四方相存在, 从而提高材料的强度与断裂韧性. Al2O3含量为20%(质量分数)时, 复相陶瓷的抗弯强度、断裂韧性分别为676.7和10 MPa*m1/2, 其值接近湿化学法制备的复相陶瓷的力学性能. 相变增韧与颗粒弥散增韧作用相互叠加提高了复相陶瓷材料的力学性能.     

Low-temperature synthesis of SrAl2O4 by a modified sol-gel route: XRD and Raman characterization

Among other alkaline-earth aluminates, the monoclinic (M) polymorph of SrAl₂O₄ can be used as host material for Eu²⁺ luminescence based phosphors. With the aim of reducing the synthesis temperature of this polymorph, we have produced and characterized by XRD and Raman scattering solid solutions of the SrAl_2−xB_xO₄ system (x?0.3) obtained by two different methods, a ceramic route and a modified sol-gel synthesis. Though the addition of boron lowers the temperature of obtention of the M polymorph in both type of samples, lower B contents are needed to stabilize the M form as single phase for samples prepared by the sol-gel method than through the ceramic route. In the sol-gel method, the M polymorph can be obtained at temperatures as low as 1200 °C, with a Boron content of just 1%. Rietveld profile analysis allows us to conclude that coexistence of the monoclinic and hexagonal polymorphs of SrAl₂O₄ occurs for samples synthesized below an onset temperature of about 1000-1100 °C, that depends on the sample composition. Above those temperatures, only the monoclinic phase is formed.