The Application of Modulated Temperature Power Compensation DSC to the Characterisation of Polymer Blends

A modulated temperature power compensated differential scanning calorimeter, MTDSC, has been built from a standard Perkin-Elmer DSC model-2 such that a computer generated voltage has been applied to induce a sinusoidal change in sample temperature superimposed on a linear heating rate. The effect of amplitude of the temperature fluctuation, modulation period and block temperature on the reversibility has been assessed from the Lissajous diagram of heat flow vs. sample temperature. From their reproducibility and symmetry the most effective conditions for operating the MTDSC has been deduced. The specific heat of sapphire has been measured using these operational conditions for comparison with conventional DSC. Phase separated blends of polycarbonate (PC) and polyethylene terephthalate (PET) have been analysed. This revised version was published online in August 2006 with corrections to the Cover Date.     

Estimation of the Parameters Describing the Changes of Conversion Degree Under Polyisothermal Conditions

The possibility of estimation of a slope of the independent variable 1/T, for the observed conversion degree in the form of a [time*temperature] matrix, has been analyzed. It has been shown that for such a case the covariance of time and temperature does not amount of zero; the procedure of estimation of the slope can be simplified by making one of the variables (time) latent. This revised version was published online in August 2006 with corrections to the Cover Date.     

Temperature response of a number of plastic dosimeters for radiation processing

Various plastic dosemeters are employed for dosimetry control of radiation processing within gamma and electron irradiation facilities.

The temperature response of a dosimeter is important when the dose to such a dosimeter is accumulated under varying irradiation temperatures. Such measurements would be significant for proper assessment of the dose for better process control, as well as, performance evaluation of dosimetry systems.

In this work we have developed a high current peltier junction temperature controller system for our Gammacell-220. This system has been designed to regulate the operating temperature of the irradiation chamber in the range of 0 to 80 C this system has been applied to measure the temperature response of the red perspex, a local clear PMMA, Gammex, Gammachrome, and Gafchromic dosimeters. The curves of relative performance or variation of the induced optical densities of the above dosemeters versus the irradiation temperature at fixed dose values are obtained.     

Thermostable persilylated polar glass capillary columns by the ammonia-etching method

Static ammonia etching has been used to effect regular surface roughening of glass capillaries. Following such treatment, polar phases could be coated after persilylation with varioussilylation agents such as hexamethyl-, tetramethyldiphenyl-, and tetra- phenyldimethyldisilazane, respectively. This method produces columns of high thermostability, which is limited only by the maximum applicable temperature for the phase itself.     

Ultrasound velocity and density studies in some refined and unrefined edible oils

Density and ultrasonic velocity at a frequency of 3?MHz and in the temperature range 298–333?K are measured in some of the refined and unrefined edible oils, namely coconut oil, castor oil, sunflower oil, kardi (safflower oil) and groundnut oil, which are predominantly used in south India. Velocity has been observed to be decreasing with temperature nonlinearly in some oils in the temperature range studied. This is in agreement with others' observations made in different oils and fats. Velocity change with temperature is attributed to change in intermolecular distance with temperature and the nature of variation depends on the internal molecular dynamics. Density of all the oils has been found to be decreasing with temperature. Various physical parameters such as specific volume, molar sound velocity, adiabatic compressibility, molar compressibility and intermolecular free length have been estimated using measured data on velocity and density.     

Discotic liquid crystals Physical parameters of some 2,3,7,8,12,13-hexa(alkanoyloxy)truxenes. Observation of a re-entrant isotropic phase in a pure disc-like mesogen

The synthesis of a new discotic mesogen, 2,3,7,8,12,13-hexa(octadecanoyloxy)-truxene is reported. This new compound has been studied using polarization microscopy, differential scanning calorimetry, small angle X-ray scattering and adiabatic calorimetry. The results are compared with those of two other truxene derivatives from the same series: 2,3,7,8,12,13-hexa(decanoyloxy)truxene and 2,3,7,8,12,13-hexa(tetradecanoyloxy)truxene. Refractive index measurements have been performed on these three truxene derivatives as a function of temperature. A re-entrant isotropic phase has been observed in 2,3,7,8,12,13-hexa(octadecanoyloxy)truxene. This is the first report of such a phase in a pure mesogen. We also report measurements of the ratio of the Frank constants for splay and bend in the nematic regime of this new mesogen as a function of temperature using the magnetic Frederiks transition technique.     

Cold microwave chemistry: synthesis using pre-cooled reagents

A novel experimental procedure for chemical reactions has been devised that involves mixing and then freezing the reagents (organic solvent-free) to a sub-zero temperature such as −30 °C. This frozen mixture is exposed to microwave irradiation for a brief period of time. The use of pre-cooled reagents may give a single product not obtained by traditional microwave irradiation at room temperature. Interestingly, such a product may provide information about mechanisms by identifying the first step of a multiple step reaction.     

Temperature variation effects on the determination of acidity constants through the internal standard–capillary electrophoresis method

The internal standard (IS) CE (IS‐CE) method is an interesting alternative to other methods for the determination of acidity constants of compounds. Although some of the advantages of this method have been already reported, the method has not been tested yet as regards to temperature effects. This has been the aim of this work, where it is demonstrated that the method can be applied successfully for the determination of pK_as at different temperatures, if the acidity constant of the IS at the desired temperature is known. The fact of obtaining the acidity constants at different temperatures allows the calculation of some thermodynamic quantities, such as the molar standard enthalpy and the molar standard entropy in a fast way. It is also demonstrated that if the IS and the test compound have similar standard enthalpy increment, the IS compensates uncontrolled possible temperature fluctuations (e.g., due to Joule heat) inside the capillary obtaining reliable acidity constant values at the desired temperature.     

Synthesis of size-controlled and shaped copper nanoparticles

The synthesis of stable, monodisperse, shaped copper nanoparticles has been difficult, partially because of copper's propensity for oxidation. This article reports the findings of an investigation of a synthetic route for the synthesis of size-controllable and potentially shape-controllable molecularly capped copper nanoparticles. The approach involved the manipulation of reaction temperature for the synthesis of copper nanoparticles in organic solvents in the presence of amine and acid capping agents. By manipulating the reaction temperature, this route has been demonstrated for the production of copper nanoparticles ranging from 5 to 25 nm. The size dependence of the melting temperature of copper nanoparticles, especially for surface melting, is believed to play an important role in interparticle coalescence, leading to size growth as the reaction temperature is increased. Control of the reaction temperature and capping molecules has also been demonstrated to produce copper nanoparticles with different shapes such as rods and cubes. The previously proposed combination of the selective formation of a seed precursor and a selective growth direction due to the preferential adsorption of capping agents on certain nanocrystal facets is believed to be responsible for shape formation by kinetically controlling the growth rates of crystal facets. The nanoparticles are characterized using TEM, XRD, and UV-visible techniques. A mechanistic consideration of the size control and shape formation is also discussed.     

Use of literature values of temperature programmed retention indexes in qualitative analysis by isothermal gas chromatography

Numerous reports have appeared on the determination of temperature programmed retention indexes in gas chromatography and although chromatographic variables should be completely consistent with published data if such indexes are to be of use, the reproduction of such rigorous parameters is quite difficult. This report presents an approximate method for using published values of temperature programmed retention indexes in isothermal chromatography. In general, the temperature dependence of the isothermal retention indexes of a number of compounds can be expressed as a series of oblique lines on a plot with retention index as the abscissa and temperature as the ordinate; the elution order of the compounds at a given, isothermal, temperature is then indicated by the points at which the compounds' oblique lines cut the horizontal line corresponding to the temperature of interest. In linear temperature programmed chromatography, the horizontal line representing isothermal operation becomes, to a first approximation, a sloping line with a gradient corresponding to the programming rate: this has been verified experimentally and may be valid over a wide range of temperatures. This line can be used to predict isothermal retention indexes for use in qualitative analysis.     

Description and modeling of polyurethane hydrolysis used as thermal insulation in oil offshore conditions

Polymers are widely used for passive thermal insulation coatings on steel pipe in offshore oil and gas production. In this industry, structures used in deep sea have to be reliable, as they are in service for more than 20 years in a very severe environment: sea water, hydrostatic pressure and temperature gradient. One of the main questions is how to test and predict the lifetime of such structures in the laboratory? This study presents one approach that has been developed to characterize and predict the degradation of polymers used as thermal insulation materials.This paper is dedicated to polyurethane (polyether based) degradation in sea water at high temperature. Ageing has been performed in natural sea water under hydrostatic pressure at temperatures ranging from 70 to 120 °C on 2 mm thick samples. Water diffusion in the material and hydrolysis have been characterized using mass evolution and tensile tests. Based on these results, a model for the urethane hydrolysis reaction is proposed.     

Reversible and irreversible crystallization in high-density polyethylene at low temperature

Reversible and irreversible crystallization and melting of high-density polyethylene at low temperature has been re-evaluated and is discussed in terms of the concept of the specific reversibility of a crystal. The concept of the specific reversibility links reversible and irreversible melting of a specific crystal such that reversible melting occurs only at slightly lower temperature than irreversible melting. In this study evidence for irreversible crystallization at low temperature in high-density polyethylene is provided, non-avoidable by primary crystallization and extended annealing at high temperature. The simultaneously observed reversible crystallization and melting at low temperature can be attributed to lateral-crystal-surface activity in addition to the well-established reversible fold-surface melting, dominant at high temperature, and evidenced by small-angle X-ray data available in the literature. This revised version was published online in August 2006 with corrections to the Cover Date.     

Beneficiation of zinc from electric arc furnace dust using hydrometallurgical approach

Zinc bearing wastes such as electric arc furnace dust (EAFD) obtained from steel making constitute an important resource for zinc extraction. Inclusion of heavy metals such as Pb, Cd, Cu, Cr, Ni, etc., in these wastes makes them hazardous to use and/or dispose. In the present research work, leaching kinetics of EAFD with sulfuric acid has been investigated and various experimental parameters such as concentration of lixiviant, stirring rate, sample particle size, liquid/solid proportion, and temperature of the reaction have been optimized. It has been found that the dissolution rate of EAFD increases with rise in temperature, acidic strength, rate of stirring, liquid to solid proportion and with reduction in EAFD particle size. From the analysis of leaching kinetic data by means of graphical and statistical methods, it has been evaluated that the leaching kinetics of EAFD is dictated by surface diffusion reaction. Apparent energy of activation for the leaching reaction of EAFD with sulfuric acid is found to be 13.1 kJ mol^–1 within the temperature range of 308 to 358 K.     

The Use of Adiabatic Calorimetry for the Process Analysis and Safety Evaluation in Free Radical Polymerization

Adiabatic calorimetry is a technique that has been introduced as an important approach to hazard evaluation of exothermically reactive systems. In this paper the free radical polymerization of methyl methacrylate (MMA) has been studied. One of the most important aspects of MMA polymerization is its exothermicity and autoaccelerating behaviour, these characteristics can generate the occurrence of a runaway reaction.In a runaway situation the reacting system is close to adiabatic behaviour because it is unable to eliminate the heat that is being generated. An even worse situation can be reproduced in the laboratory with the Phi-Tec pseudo-adiabatic calorimeter. Process design parameters that are usually calculated from thermodynamic data or using semiempirical rules, such as adiabatic temperature rise or maximum attainable pressure, can be directly determined.The existence of the ceiling temperature has been experimentally demonstrated.This revised version was published online in November 2005 with corrections to the Cover Date.     

Hydrocarbon type analysis by thin-layer chromatography with flame-ionization detection: vacuum gas oils, heavy feeds, and hydroprocessed products

Thin-layer chromatography with flame-ionization detection (TLC-FID) provides quantitative hydrocarbon type data as well as distribution of aromatics by ring number. This method has been applied to obtain amounts of saturates, aromatics, and polars in heavy oil distillates such as light vacuum gas oils and heavy vacuum gas oils derived from different crude sources. TLC-FID chromatograms and resultant quantitative hydrocarbon type data show that these distillates vary markedly in aromatic contents and aromatic ring types. Similar observations are made with several fluid catalytic cracking feeds. Effects of process parameters such as operating pressure and temperature on hydroconversion of aromatics and polars from a heavy oil are assessed by TLC-FID. It has been demonstrated that there is a preferential reduction of higher polycyclic aromatic hydrocarbons and polars with an increase of both hydrogen partial pressure and reactor temperature.     

Synthetic ceramic clay material as stationary phase in packed column supercritical fluid chromatography

Summary A novel inorganic synthetic clay material (SC) has been evaluated as the stationary phase in packed-column, supercritical fluid chromatography (SFC). The molecular recognition capability of the SC stationary phase in SFC for polycyclic aromatic hydrocarbons has been evaluated using carbon dioxide and carbon dioxide modified with methanol as the mobile phase. This recognition derives from the layer structure of the SC material which acts as a slit to distinguish non-planar solutes from the molecular-molecular interaction between solute and stationary phase and leads to smaller retention for non-planar solutes. The recognition capability is also dependent on the SFC conditions such as column pressure and column temperature.     

Synthesis of a Novel High Solid Coating Used in Automobile

High solid coating is one of the most important environmental friendly coatings, and has been obtained great attention since 70s' last century. For there are high volatile organic compounds(VOCs) in the conventional coatings, which cause both a serious pollution and consume of a plentiful of natural resource, such as petroleum. The development and production of high solid coatings is pressing target for all the countries, especially for China due to our heavy population and short of resources. Based on the requirement, a novel coating with high solid content has been developed in our lab. The solid content of the resin is 80%, compared to the 55% of conversional resin. This coating is characterized by its unique molecular architecture, it is a kind of hyper-branched polymer with uniform distribution of the reactive groups along the molecular backbone, which can react with other chemicals to form a cross-linking structure at high temperature.The coating has a lower viscosity and lower Tg corresponding to its branched structure( scheme 1).This coating has been applied in the automobile finishing. The experimental results indicated that the developed coating presented high performance properties in fastness, mar resistance, and hardness, it also reduced the baking temperature, resulting in a energy saving.     

A gravimetric procedure for the determination of wet precipitated sulphur, dissolved sulphur, soluble sulphides and hydrogen sulphide

Elemental sulphur (in wet precipitated form or dissolved in organic solvents) and hydrogen sulphide have been determined gravimetrically at room temperature by conversion into copper sulphide by elemental copper in presence of an organic solvent such as benzene or acetonitrile. Any solvent in which sulphur is soluble can be used. The black copper sulphide formed can be weighed or determined iodometrically. Analysis indicates the black compound to be Cu(1.8)S. This room temperature method is a versatile one-step procedure sensitive to microgram or macro amounts of sulphur. It has been used for determining the solubility of sulphur in tetrahydrofuran and dioxan. The apparent heat of solution indicates that sulphur dissolves in these solvents without any marked solute-solvent interactions.     

Hydrogenation of aldehydes and ketones catalyzed by a polysulfosiloxane–platinum complex

An acidic inorganic polymer, polysulfosiloxane, has been prepared and used as ligand for preparing a polysulfosiloxane–platinum complex. It has been found that such a complex could catalyze the hydrogenation of aldehydes and ketones to alcohols, giving as much as 100% yield at room temperature and under atmospheric pressure. Temperature, S/Pt molar ratio in the complex and solvents greatly influenced the reaction. This complex was very stable and could be used several times without any change in catalytic activity.