Probing internal environment of sol–gel bulk and thin films using multiple fluorescent probes

The selection of sol compositions, conditions of preparation and storage of gels are an important aspects for encapsulating biomolecules in gel matrix for applications in biosensor. In the present investigation, fluorescence spectroscopic measurements (emission and fluorescence lifetimes) were carried out in bulk gel and thin films prepared from sols with water and tetraethyl-orthosilicate (TEOS) containing different fluorescent probes viz Hoechst 33258 (H258), Pyranine (Py), and 7-Azaindole (7-AI) in different sols. Sols were prepared with addition of water, HCl and surfactant Triton X-100, and stored at room temperature (RT) and low temperature (4 °C). The spectral characteristics have been compared for two different storage conditions as a function of aging. The results of the present study clearly suggested that the internal environment of gels specifically the content of water inside the pores of the sol–gel matrix can be controlled by storage at 4 °C as compared to RT.     

On the nature of the processes occurring in silver doped SiO<Subscript>2</Subscript> films under heat treatment

The processes taking place on air-heating of SiO₂−Ag⁺ films and xerogels produced from the SiO₂ sols of different pH (3.7 or 9.5) were investigated. Silver nanoparticles 10–40 nm in size tolerant to oxidation at temperatures above 600 °C were found to be formed in the systems whatever the pH value of the starting sol. SiO₂ crystallization giving the cristobalite phase in the temperature range from 500 to 800 °C was shown to proceed only in the films produced from the acidic sol, while in those formed from the alkali one SiO₂ remained amorphous. A mechanism by which the formation of Ag nanoparticles and the cristobalite phase occurs in the films at the oxidative conditions is suggested.     

Preparation of highly stable TiO<Subscript>2</Subscript> sols and nanocrystalline TiO<Subscript>2</Subscript> films via a low temperature sol–gel route

Highly stable TiO₂ sols were prepared by adjusting the water-to-titanium molar ratio to ~4 in the process of hydrolysis and condensation of titanium isopropoxide in ethanol with HNO₃. Particularly, long-term stable TiO₂ sols were prepared without adding any chemical additives. Anatase TiO₂ nanocrystallites with sizes of 3–5 nm in diameter were uniformly dispersed in the stable sol. Crystallized TiO₂ films were successfully deposited on Si (100) using the stable sol via a dip-coating process with low temperature curing at as low as 100 °C. The synthesized TiO₂ sols and films are promising for use in flexible or dye-sensitized solar cells.     

Aging effect of diethanolamine derived precursor sol on TiO<Subscript>2</Subscript> films deposited at different annealing temperatures

A diethanolamine stabilized precursor sol has been utilized for studying the effect of sol aging and annealing temperature on key properties of TiO₂ films. X-ray diffraction investigations have shown increased crystallite size in the films as a function of both sol aging and the thermal treatment. Fourier transform infrared studies have elucidated that cleavage of the bond involving diethanolamine and the alkoxide in the films requires high temperature annealing treatment upon the use of aged sol for the deposition of the films. Multiple step chronoamperometry has shown the ion storage capacity of the films increases as a function of sol aging, with the highest extent of Li ion insertion being obtained for films produced from as-prepared and aged sols and subsequently annealed at, 300 and 350 °C, respectively. Films with excellent optical quality were obtained. Ellipsometry revealed that the refractive indices of the films vary from 1.67 to 2.02. The highest thickness obtained in these films was nearly 900 nm. The bandgaps of the films for both direct and indirect transitions decreased as a function of precursor sol’s aging. In addition, although the indirect bandgap values have shown a decrease with increasing annealing temperature, the direct bandgap values reveal a slight increase as a function of annealing temperature.     

Separation of benzene/cyclohexane mixtures using polyurethane–silica hybrid membranes

Mixed sols were prepared by dissolving polyurethane (a 30 wt% solution in n-propanol, PU) and tetraethylorthosilicate (TEOS) in ethanol at PU:TEOS mass ratios of 1:2, 1:1, 2:1 and 3:1. Each of the sols was coated on a porous α-alumina support tube by the dipping method, and green membranes were heat-treated at 200°C for 1 h in an atmosphere of nitrogen. A PU membrane was also prepared with PU alone. The membranes were 5–6 μm thick. The polyurethane–silica membranes were swollen in benzene but only slightly in cyclohexane at room temperature. The degree of swelling in benzene decreased with increasing fractions of TEOS in the hybrid sols. The selectivity of benzene to cyclohexane was improved due to the suppression of swelling as a result of hybridization with TEOS. The total permeation flux and benzene/cyclohexane selectivity in the membrane prepared with a sol of PU:TEOS=1:1 were 3×10⁻⁵ kg m⁻² s⁻¹ and 19, respectively.     

Preparation and characterization of diphasic sol-gel derived unsupported mullite membranes

Diphasic gels prepared by mixing freshly prepared polymeric silica and polymeric boehmite sols through a modified Al-alkoxide route in mullite compositions led to the crystallization of mullite upon heat treatment at 775 °C. Mullite formation was observed at a 100 °C higher temperature when diphasic gels were formed by mixing aged polymeric sols containing about 2 nm in diameter boehmite species. These relatively low mullite formation temperatures were attributed to the nanoscale sizes of the polymeric species of the two amorphous phases present in the diphasic gels.     

Limiting stability temperatures for copper sols stabilized by poly(<Emphasis Type="Italic">N</Emphasis>-vinyllactams)

It has been shown that stable copper sols cannot be prepared through the reduction of copper ions in aqueous solutions of poly(N-vinyllactams) in the presence of poly(N-vinylpyrrolidone) in the temperature range 50–70°C, while in the presence of poly(N-vinylcaprolactam), the said sols cannot be prepared at temperatures below ～12°C. This tendency is related to the thermodynamic instability of complexes formed via noncovalent interactions of copper nanoparticles with polymer macromolecules in corresponding temperature ranges. Stable sols synthesized in the presence of the above polymers at other temperatures rapidly lose stability in the said temperature ranges, and this effect is accompanied by the aggregation of metal particles. The experimental results provide evidence that there is a relationship between the stability of complexes macromolecules-metal nanoparticles and the thermodynamic quality of the solvent.     

Sol-gel derived oxides and mixed oxides catalysts with narrow mesoporous distribution

A novel sol-gel process for preparing oxides and mixed oxides sols from precipitation and peptization process is reported in this article. Inorganic salts are used as raw materials in this study. It is found that the amount of acid has great influence on the stability and particle diameter distribution of the precursor sols. Ultrasonic treatment is used to prepare alumina sol at room temperature. The result of 27AI NMR shows that there exist AI_13~(7+) species in the sol. By controlling the sol particles with narrow particle diameter distribution, alumina, titania and silica-alumina (SA) materials with narrow mesoporous distribution are formed by regular packing of sol particles during gelation without using any templates. The results also show that the structure and particle diameter distribution of precursor sol determine the final materials' texture.     

Preparation and characterization of TiO2 sols and their UV-cured hybrid thin films on plastic substrates

In this research, TiO₂ sols were synthesized via a sol?Cgel reaction at room temperature followed by heating under reflux. Hybrid thin films were prepared using the TiO₂ sols and dipentaerythritol hexacrylate on poly(methyl methacrylate) substrates via spin coating followed by UV-curing. The images of transmission electron microscopy (TEM) and results of dynamic light scattering (DSL) showed that some originally synthesized TiO₂ nanoparticles aggregated while many small-sized (~5?nm) TiO₂ nanoparticles still existed after reflux heating. The synthesized TiO₂ sols showed poor photocatalytic ability, which might avoid degradation of organic moieties in the hybrids. The refractive indices of the hybrid thin films were increased from 1.66 to 1.82 while the water contact angles on the thin films were increased from 70.2° to 87.7° with the increment of TiO₂ content. Increasing the heating time of the TiO₂ sol resulted in an increase in the refractive index and contact angle.     

Synthesis of high surface area nanocrystalline anatase-TiO2 powders derived from particulate sol-gel route by tailoring processing parameters

Stabilised titania sols were prepared using an additive free particulate sol-gel route, via electrostatic stabilisation mechanism, with various processing parameters. Peptisation temperature, 50°C and 70°C, and TiO₂ concentration, 0.1, 0.2 and 0.4 molar, were chosen as processing parameters during sol preparation. Results from TiO₂ particle size and zeta potential of sols revealed that the smallest titania hydrodynamic diameter (13 nm) and the highest zeta potential (47.7 mV) were obtained for the sol produced at the lower peptisation temperature of 50°C and lower TiO₂ concentration of 0.1 M. On the other hand, between the sols prepared at 70°C, smaller titania particles (20 nm) and higher zeta potential (46.3 mV) were achieved with increasing TiO₂ concentration up to 0.4 M. X-ray diffraction (XRD) and Brunauer-Emmett-Teller (BET) results of produced powders annealed at different temperatures showed that the 300°C annealed powder made from 0.1 M sol prepared at 50°C was a mixture of anatase and brookite, corresponding to a major phase of anatase (∼95% estimated), with the smallest average crystallite size of 1.3 nm and the highest specific surface area (SSA) of 193 m²/g. Furthermore, increasing TiO₂ concentration up to 0.4 molar for the sols prepared at 70°C resulted in decreasing the average crystallite size (1.9 nm at 300°C) and increasing SSA (116 m²/g at 300°C) of the powders annealed at different temperatures. Anatase-to-rutile phase transformation temperature was increased with decreasing peptisation temperature down to 50°C, whereas TiO₂ concentration had no effect on this transition. Anatase percentage increased with decreasing both peptisation temperature and TiO₂ concentration. Such prepared powders can be used in many applications in areas from photo catalysts to gas sensors.     

Triple redox/temperature responsive diselenide‐containing homopolypeptide micelles and supramolecular hydrogels thereof

Stimuli‐responsive polypeptides are receiving much attention for drug delivery systems and tissue engineering scaffolds; however, it is challenging to construct multiple‐responsive polypeptides and one‐component polymeric hydrogels. Herein, a novel type of triple redox/temperature‐responsive diselenide‐containing poly(methoxydiethylene glycol‐l ‐glutamate) homopolypeptide was facilely synthesized by selenocystamine‐initiated ring‐opening polymerization in DMF at 30 °C, and their chemical structures and physical properties were fully characterized by means of ¹H NMR, GPC, FT‐IR, WAXD, and CD. They self‐assembled into spherical micelles in aqueous solution, which possess a lower critical solution temperature, redox‐responsiveness inherited from diselenide bond, and the triple stimuli‐sensitive self‐assembly behaviors, as characterized by means of turbidity, DLS, TEM, and zeta potential measurements. The diselenide‐containing homopolypeptides formed supramolecular hydrogels at room temperature, exhibiting a thermal gel–sol transition. The rheological tests evidence that the mechanical modulus of the hydrogel is independent of angular frequency within 100 rad/s and at 25 °C, in which the storage modulus of G′ is order of magnitude greater than the loss modulus of G″, displaying a solid‐like elastic behavior. Moreover, the mechanical modulus of the hydrogel can be tuned by changing the chain length of the homopolypeptide, the 10‐mM 1,4‐dithiothreitol (DTT) reduction, and 1 mM H₂O₂ oxidation, respectively. Consequently, this work provides a simple strategy to fabricate triple‐stimuli responsive polypeptide micelles and one‐component hydrogels. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1067–1077     

Studies of Lead Zirconate Titanate Sol Ageing Part I: Factors Affecting Particle Growth

The formation and growth of polymeric particles during the hydrolysis and condensation of PbZr_0.3Ti_0.7O₃ (PZT 30/70) precursor solutions have been studied as functions of time by using photon correlation spectroscopy (PCS). Particle shape was deduced by measuring the rheological properties of the sols and was found to remain chain-like during sol ageing. Various factors that affect the ageing of PZT sols have been investigated. Ethylene glycol (EG) was found to greatly accelerate the hydrolysis and condensation of the acid-modified Pb-free Zr/Ti solutions but had little effect on the particle growth for the Pb-containing PZT sols. Temperature and H₂O concentration were found to have major effects on the ageing behaviors. The higher the temperature and H₂O concentration, the higher the particle growth rates and the faster the sol gels.     

Preparation of colloidal solutions of noble metals stabilized by polyoxometalates and supported catalysts based on these solutions

Conditions for the preparation of stable aqueous monometallic and bimetallic colloidal solutions (sols) of noble metals (Ru, Rh, Pd, Pt, Ir, Ag, and Au) in the presence of polyoxometalates containing W, Mo, V, and Nb were found. The stability of sols against coagulation at room temperature was studied. The metal/C samples prepared by metal adsorption from sols were studied by powder X-ray diffraction analysis and transmission electron microscopy. The following factors of importance for the preparation of a stable sol are discussed: (1) the formation of a sol of a metal polyhydroxo complex stabilized by a polyoxometalate (preliminary stage) and (2) the formation of polyoxometalate-metal clusters in the course of reduction of polyhydroxo complexes.Translated from Kinetika i Kataliz, Vol. 45, No. 6, 2004, pp. 921–929.Original Russian Text Copyright © 2004 by Maksimova, Chuvilin, Moroz, Likholobov, Matveev.     

Kinetic study on photochromism of WO3 aqueous sol and its enhancement accompanying spectral changes by the addition of TiO2 aqueous sol

Photochromism of a WO₃ aqueous sol has been investigated in a nitrogen atmosphere under controlled temperature. Effects of ageing of the WO₃ sols, concentrations of WO₃ sols or Cl⁻ ion and temperature on the coloring rate were examined. The coloring rate was the first-order with respect of the WO₃ concentration. The coloring process was accelerated by an addition of TiO₂ aqueous sols. Spectral changes were measured using the mixing sol with various molar ratios (γ) of WO₃ and TiO₂. The absorption spectra changed from those having the single peak at 775 nm to those with two peaks at 640 and 980 nm. Such spectral transformation was ascribed to the structural change of the WO₃ nanoclusters, depending on the γ value and the concentration of Cl⁻ ion.     

Photopatternable hybrid sol–gel films: A liquid Si NMR investigation of the inorganic network formation

Methacryloxypropyltrimethoxysilane precursor has been involved in the realization of optical elements in crack free thick films (ranging from 15 to 100 μm), through spatially controlled photopolymerization. First, alkoxysilane functions were partially hydrolyzed and condensed. Then, using a photoinitiator, free radical photopolymerization was proceeded by irradiating the sample under UV or visible light. Since an organic network is formed in the matrix of the primarily formed inorganic network, understanding the formation of the silicate backbone was of first importance to ensure the creation of crack free thick films through efficient polymerization.

Liquid ²⁹Si NMR spectroscopy was used to investigate the inorganic network formation. Material preparation required evaporation of the volatile solvents released by the sol–gel process and limitation of the condensation degree. Both conditions were achieved by a drying process at room temperature. The structure and the composition of the dried sols were investigated and compared to non-dried sols. NMR peak fitting pointed out to the presence of a large variety of cyclic and linear oligomers in the sol. The structure of the dried sol appeared to depend both on the aging time and on the storage temperature. All these results have to be taken into account when the condensation degree has to be limited for specific optical applications.     

Preparation methods and thermal stability of calcipotriol solid lipid nanoparticles and efficacy in plaque psoriasis treatment

The preparation of Calcipotriol by solid lipid nanoparticles and the encapsulation of drugs in solid lipids are expected to obtain a new preparation with strong cutin permeability, slow release and targeting effect, so as to improve the local therapeutic effect of the drug and reduce the occurrence of skin irritation symptoms. In this work, Calcipotriol solid lipid nanoparticle (CPT-SLN) preparation methods are introduced and the stability of CPT-SLNs gel was evaluated by appearance, leakage rate and content. The performance was stable in a low-temperature environment of 4 °C for 40 days. There were no significant changes in appearance, and drug content and permeability can be controlled around 0.00469% and 0.26. However, it has poor stability under the storage conditions of 25 °C and 40 °C at room temperature. Therefore, the suitable conditions for the gel storage should be around 4 °C and sealed away from light. Pharmacodynamic experiments showed that CPT solid lipid nanoparticle gel was more effective than market-sale Calcipotriol ointment in the treatment of psoriasis. Further clinical tests have shown that CPT-SLNS can cure plaque psoriasis more effectively.

     

紫外光辐射对TiO2溶胶的影响研究

用紫外-可见吸收光谱、动态光散射与透射电镜研究紫外光辐射对T₂溶胶的影响,结果表明,光辐射使T₂溶胶在可见光区的吸收减少,紫外区吸收增加,吸收带隙增大.与非光辐射的T₂溶胶粒子相比,光辐射使T₂溶胶粒子分布均匀且平均粒径减小,提高了T₂纳米粒子在室温下的晶化程度.     

Synthesis of 15-(4-[<Superscript>131</Superscript>I]iodophenyl)pentadecanoic acid (<Emphasis Type="Italic">p</Emphasis>-IPPA) via tin-precursor using Chloramine-T as an oxidant

A rapid method for the preparation of the radioiodinated 15-(4-iodophenyl)pentadecanoic acid (p-IPPA) was developed. ¹³¹I-p-IPPA was obtained from the corresponding tin precursor and ¹³¹I-iodide using Chloramine-T as an oxidant in a radiochemical yield of 90 ± 1.4% with a radiochemical purity > 99% when performing the labeling at room temperature within a reaction time of 3 min. The study of dependences on temperature (0, 20 and 80 °C) and reaction time (1, 3, 5, 10 and 30 min) showed no yield increase with higher temperatures and prolonged reaction times but the formation of side products.     

Effect of calcination temperature on the microstructure of porous TiO<Subscript>2</Subscript> film

To obtain porous TiO₂ film, the precursor sol was prepared by hydrolysis of Ti isopropoxide and then complexed with trehalose dihydrate. The porous TiO₂ film was fabricated by the dip-coating technique on glass substrates using this solution. The TiO₂ film was calcined at 500 °C. The maximum thickness of the film from one-run dip-coating was ca. 740 nm. The film was composed of nanosized particle and pores. The porosity of the TiO₂ film was increased by addition of trehalose dihydrate to the sol. The porous TiO₂ films were calcined at different temperatures. The effects of calcination temperature on the microstructure of the porous TiO₂ film were investigated. The porous film prepared from sol containing trehalose still kept the porous structure after calcination at 950 °C. The phase transition temperature of the film from anatase to rutile was shifted from 650 to 700 °C by addition of trehalose to the sol.     

Bismuth titanate thin films prepared by wet-chemical techniques: effect of sol ageing time

In this work, layered perovskite bismuth titanate (Bi₄Ti₃O₁₂) thin films were fabricated on α-alumina substrates by spin coating process. Precursor sol was prepared by sol–gel process from bismuth nitrate and titanium butoxide in concentrated acetic acid, with diethylamine as a stabilizer. Processes occurring in the precursor sol were followed in the ageing period of 20 days. Thin films prepared from the as-synthesized and aged sols are crack-free, with the thickness of ~1 μm, uniform surface texture and rounded grains having grain size in nanometer range. Sintering of thin films was performed at various temperatures, and sintered thin films exhibited dense structure, fully crystallized with typical Aurivillius phase and without any preferred orientation and impurity phase. The influence of ageing of the precursor sol on the microstructure of obtained thin films was also investigated. Direct relation between hydrodynamic diameter of precursor particles and the morphology and the grain size of the obtained films was observed.