Ammonia synthesis by means of plasma over MgO catalyst

Ammonia synthesis from H₂-N₂ mixed gas was studied at room temperature in a glow-discharge plasma in the presence of metals or metal oxides. Magnesia (MgO) and calcia (CaO), which are oxides with solid basicity, revealed catalytic activity in the plasma synthesis of ammonia, although they are catalytically inactive in industrial ammonia synthesis. The acidic oxides (Al₂O₃, WO₃, and SiO₂-Al₂O₃) lead to the consumption of the reactant, i.e., the H₂-N₂ mixed gas. No ammonia was isolated. Metal catalysts showed higher activity than the above basic oxides. They have, however, different activities. The reaction was faster over the active materials than over sodium chloride (NaCl) or glass wool or in a blank reactor without any catalyst.     

等离子体修饰磁载TiO2光催化剂性能研究

以化学共沉法制备的CoFe₂O₄纳米粒子为磁核,采用TiCl₄水解包覆技术制备磁载二氧化钛纳米复合粒子CoFe₂O₄ /TiO_x(TCF),利用低温等离子体技术修饰TCF制备了CoFe₂O₄/TiO₂(PTCF)纳米复合光催化剂。运用VSM(振动样品磁强计)技术对样品磁性能进行研究,结果表明：等离子体修饰后的复合材料仍具有较高的饱和磁化强度,可在外加磁场作用下实现催化剂在水中的分离与回收;样品的XRD、TEM和UV-Vis分析测试结果表明：等离子体修饰后的复合材料有锐钛矿型TiO₂存在;TEM谱图显示磁核CoFe₂O₄的平均粒径约为20 nm,TCF复合粒子的粒径约为30~40 nm,TiO₂包覆层的厚度为10~20 nm。与纯TiO₂相比PTCF样品对光的吸收拓展到整个紫外-可见区,扩大了光谱响应范围;对甲基橙溶液降解的光催化活性评价研究表明：TCF复合粒子等离子体修饰后的PTCF纳米复合光催剂的光催化活性明显提高。     

Comparative Study of the Decomposition of CCl4 in Cold and Thermal Plasma

Decomposition of carbon tetrachloride was studied in an inductively coupled thermal plasma reactor and in a low temperature, non-equilibrium plasma reactor, in neutral and oxidative conditions, respectively. In neutral conditions formation of solid soot, aliphatic- and cyclodienes was observed in equilibrium, and products, such as Cl₂ and C₂Cl₆ were detected in non-equilibrium plasma. Feeding of oxygen into the thermal plasma reactor depressed both soot and dienes formation and induced the formation of oxygen containing intermediates and products. GC-MS analyses of the gaseous products and the extract of the soot referred to as complex decomposition and recombination mechanism at given conditions. Presence of oxygen in the low temperature plasma reactor results in the formation of carbonyl compounds as intermediers. CO₂ and Cl₂ revealed as final products of CCl₄ decomposition in cold plasma.     

Deposition of Diamondlike Carbon Film and Mass Spectrometry Measurement in CH4/N2 RF Plasma

The deposition of diamondlike carbon (DLC) film and the measurements of ionic species by means of mass spectrometry were carried out in a CH₄/N₂ RF (13.56 MHz) plasma at 0.1 Torr. The film deposition rate greatly depended on both CH₄/N₂ composition ratio and RF power input. It was decreased monotonically as CH₄ content decreased in the plasma and then rapidly diminished to negligible amounts at a critical CH₄ content, which became large for higher RF power. The rate increased with increasing RF power, reaching a maximum value in 40% CH₄ plasma. The predominant ionic products in CH₄/N₂ plasma were NH⁺ ₄ and CH₄N⁺ ions, which were produced by reactions of hydrocarbon ions, such as CH⁺ ₃, CH⁺ ₂, CH⁺ ₅, and C₂H⁺ ₅ with NH₃ molecules in the plasma. It was speculated that the production of NH⁺ ₄ ion induced the decrease of C₂H⁺ ₅ ion density in the plasma, which caused a reduction in higher hydrocarbon ions densities and, accordingly, in film deposition rate. The N⁺ ₂ ion sputtering also plays a major role in a reduction of film deposition rate for relatively large RF powers. The incorporation of nitrogen atoms into the bonding network of the DLC film deposited was greatly suppressed at present gas pressure conditions.     

配位化合物Zn(Met)3(NO3)2·H2O(s)(Met=L-α-蛋氨酸)的低温热容及标准摩尔生成焓

利用精密绝热热量仪测定了化合物配合物Zn(Met)₃(NO₃)₂·H₂O (s) (Met=L-α-蛋氨酸)在78-371 K温区的摩尔热容. 通过热容曲线解析, 得到了该配合物的起始脱水温度为T_D=325.10 K. 将该温区的摩尔热容实验值用最小二乘法拟合得到了摩尔热容(C_p)对约化温度(T)的多项式方程, 由此计算得到了配合物的舒平热容值和热力学函数值. 基于设计的热化学循环, 选择100 mL of 2 mol·L^-1 HCl为量热溶剂, 利用等温环境溶解-反应热量计, 得到了298.15 K配合物的标准摩尔生成焓为Δ_fH_m⁰[Zn(Met)₃(NO₃)₂·H₂O(s),s]=-(1472.65±0.76) J·mol^-1.     

Thermoelectric properties of Ag-doped n-type (Bi2Te3)0.9-(Bi2−xAgxSe3)0.1 (x=0-0.4) alloys prepared by spark plasma sintering

Ag-doped n-type (Bi₂Te₃)_0.9-(Bi_2−xAg_xSe₃)_0.1 (x=0-0.4) alloys were prepared by spark plasma sintering and their physical properties evaluated. When at low Ag content (x=0.05), the temperature dependence of the lattice thermal conductivity follows the trend of (Bi₂Te₃)_0.9-(Bi₂Se₃)_0.1; while at higher Ag content, a relatively rapid reduction above 400 K can be observed due possibly to the enhancement of scattering of phonons by the increased defects. The Seebeck coefficient increases with Ag content, with some loss of electrical conductivity, but the maximum dimensionless figure of merit ZT can be obtained to be 0.86 for the alloy with x=0.4 at 505 K, about 0.2 higher than that of the alloy (Bi₂Te₃)_0.9-(Bi₂Se₃)_0.1 without Ag-doping.     

Thermal effect on the voltammogram of 7-ferrocenycarbonyloxy-1-heptanethiol self-assembled monolayer

The voltammetry of self-assembled monolayers (SAMs) of 7-ferrocenycarbonyloxy-1-heptanethiol (FcCO₂(CH₂)₇SH) has been studied as a function of temperature. Such SAMs are, when oxidised, susceptible to loss of ferrocene via nucleophilic attack, but at temperatures only just above room temperature, there is an accelerated loss of ferrocene from the chain termini, an increase in the capacitance of the layer in its reduced state and a positive shift in the E_1/2 value is observed. A comparison between these data and the effects of multiple scans recorded at room temperature suggests that there is a re-orientation, induced at slightly elevated temperatures, which is associated with the ferrocene ester linkage at the chain terminus and which apparently renders ferrocene more susceptible to nucleophilic attack. With the increasing of temperature, the loss of ferrocene (terminal) is accelerated, due to the capacitances and permeability of the SAM layers. The positive shift of the E_1/2 value is harder to interpret but may result because the ferrocene is in more intimate contact with the layer and is placed in a more hydrophobic, less polar environment. Other possible influences on the shift of E_1/2 are discussed. This work confirms that electroactive terminal groups can provide information on the microenvironment at the SAM/electrolyte interface through variations in current and potential.     

Conversion of natural gas to C2 hydrocarbons through dielectric-barrier discharge plasma catalysis

The experiments are carried out in the system of continuous flow reactors with dielectric-barrier discharge (DBD) for studies on the conversion of natural gas to C₂ hydrocarbons through plasma catalysis under the atmosphere pressure and room temperature. The influence of discharge frequency, structure of electrode, discharge voltage, number of electrode, ratio of H₂/CH₄, flow rate and catalyst on conversion of methane and selectivity of C₂ hydrocarbons are investigated. At the same time, the reaction process is investigated. Higher conversion of methane and selectivity of C₂ hydrocarbons are achieved and deposited carbons are eliminated by proper choice of parameters. The appropriate operation parameters in dielectric-barrier discharge plasma field are that the supply voltage is 20–40 kV (8.4–40 W), the frequency of power supply is 20 kHz, the structure of (b) electrode is suitable, and the flow of methane is 20–60 mL · min⁻¹. The conversion of methane can reach 45%, the selectivity of C₂ hydrocarbons is 76%, and the total selectivity of C₂ hydrocarbons and C₃ hydrocarbons is nearly 100%. The conversion of methane increases with the increase of voltage and decreases with the flow of methane increase; the selectivity of C₂ hydrocarbons decreases with the increase of voltage and increases with the flow of methane increase. The selectivity of C₂ hydrocarbons is improved with catalyst for conversion of natural gas to C₂ hydrocarbons in plasma field. Methane molecule collision with radicals is mainly responsible for product formation.     

Ho(NO3)3(C2H5O2N)4·H2O的低温热容和热力学函数

合成了稀土(钬, Ho)-氨基酸(甘氨酸, C₂H₅O₂N)二元配合物Ho(NO₃)₃(C₂H₅O₂N)₄·H₂O, 并且通过化学分析、元素分析和红外(IR)光谱对配合物进行了表征. 用高精度全自动绝热量热仪, 测定了该配合物在80-390 K温度区间的定压摩尔热容(C_p,m). 利用实验测定的热容数据, 采用最小二乘法, 将热容曲线上热容峰以外的两段平滑区的摩尔热容对折合温度进行拟合, 建立了热容随折合温度变化的多项式方程. 根据热容与焓、熵的热力学关系,计算出了配合物在80-390 K温度区间内,每隔5 K,相对于298.15 K的摩尔热力学函数(H_T,m-H_298.15,m)和(S_T,m-S_298.15,m). 通过热容曲线分析, 计算出了350 K附近转变过程的焓变(Δ_trsH_m)和熵变(Δ_trsS_m). 用差示扫描量热法(DSC)测定了配合物的热稳定性.     

Synthesis and characterization of La1+xSr2−xCoMnO7−δ (x=0,0.2; δ=0,1)

The n=2 Ruddlesden-Popper phases LaSr₂CoMnO₇ and La_1.2Sr_1.8CoMnO₇ have been synthesized by a sol-gel method. The O6-type phases LaSr₂CoMnO₆ and La_1.2Sr_1.8CoMnO₆ were produced by reduction of the O7 phases under a hydrogen atmosphere. The materials crystallize in the tetragonal I4/mmm space group with no evidence of long-range cation order in the neutron and electron diffraction data. Oxygen vacancies in the reduced materials are located primarily at the common apex of the double perovskite layers giving rise to square pyramidal coordination around cobalt and manganese ions. The oxidation states Co³⁺/Mn⁴⁺ and Co²⁺/Mn³⁺ predominate in the as-prepared and reduced materials, respectively. The materials are spin glasses at low temperature and the dominant magnetic interactions change from ferro- to antiferromagnetic following reduction.     

Influence of O2 Plasma on Surface Properties of PC-TiO2 Nanocomposite Film

In this work, polycarbonate-TiO₂ nanocomposite films were prepared with different percentages. The aim was to consider the effect of O₂ LF plasma (50 Hz) on the hydrophilicity, surface energy, and surface morphology of polycarbonate and polycarbonate-TiO₂ nanocomposite. Structure of samples was determined by using X-ray diffraction analysis. In comparison with the reference sample, the samples’ structure did not change after plasma treatment. Surface properties of polycarbonate and polycarbonate-TiO₂ nanocomposite films were studied by X-ray photoelectron spectroscopy (XPS), contact angle measurement, atomic force microscopy (AFM), and Vickers microhardness tester. XPS analysis showed that the surface of samples became more oxidized due to plasma treatment. The water contact angle significantly decreased from 88° to 15° after plasma treatment. It was observed that the hardness of the nanocomposite films was not modified after plasma treatment.     

Solid solubility of Yb2Si2O7 in β-, γ- and δ-Y2Si2O7

This paper examines the structural changes with temperature and composition in the Yb₂Si₂O₇-Y₂Si₂O₇ system; members of this system are expected to form in the intergranular region of Si₃N₄ and SiC structural ceramics when sintered with the aid of Yb₂O₃ and Y₂O₃ mixtures. A set of different compositions have been synthesised using the sol-gel method to obtain a xerogel, which has been calcined at temperatures between 1300 and 1650 °C during different times. Isotherms at 1300 and 1600 °C have been analysed in detail to evaluate the solid solubility of Yb₂Si₂O₇ in β-Y₂Si₂O₇ and γ-Y₂Si₂O₇. Although Yb₂Si₂O₇ shows a unique stable polymorph (β), Yb³⁺ is able to replace Y³⁺ in γ-Y₂Si₂O₇ and δ-Y₂Si₂O₇ at high temperatures and low Yb contents. IR results confirm the total solid solubility in the system and suggest a constant SiOSi angle of 180° in the Si₂O₇ unit across the system. The temperature-composition diagram of the system, obtained from powder XRD data, is dominated by the β-RE₂Si₂O₇ polymorph, with γ-RE₂Si₂O₇ and δ-RE₂Si₂O₇ showing reduced stability fields. The diagram is in accordance with Felsche's diagram if average ionic radii are assumed for the members of the solid solution at any temperature, as long as the β-γ phase boundary is slightly shifted towards higher radii.     

Reaction Mechanisms in Both a CCl2F2/O2/Ar and a CCl2F2/H2/Ar RF Plasma Environment

Decomposition of dichlorodifluoromethane (CCl₂F₂ or CFC-12) in aradiofrequency (RF) plasma system is demonstrated. The CCl₂F₂decomposition fractions _{CCl 2 F 2} and mole fractionsof detected products in the effluent gas stream of CCl₂F₂/O₂/Ar andCCl₂F₂/H₂/Ar plasma, respectively, have been determined. The experimentalparameters including input power wattage, O₂/CCl₂F₂ or H₂/CCl₂F₂ ratio,operational pressure, and CCl₂F₂ feeding concentration wereinvestigated. The main carbonaceous product in the CCl₂F₂/O₂/Arplasma system was CO₂, while that in the CCl₂F₂/H₂/Ar plasma systemwas CH₄ and C₂H₂. Furthermore, the possible reaction pathways werebuilt-up and elucidated in this study. The results of the experimentsshowed that the highly electronegative chlorine and fluorine wouldeasily separate from the CCl₂F₂ molecule and combine with the addedreaction gas. This led to the reactions terminated with the CO₂,CH₄, and C₂H₂ formation, because of their high bonding strength. Theaddition of hydrogen would form a preferential pathway for the HCland HF formations, which were thermodynamically stable diatomicspecies that would limit the production of CCl₃F, CClF₃, CF₄, andCCl₄. In addition, the HCl and HF could be removed by neutral orscrubber method. Hence, a hydrogen-based RF plasma system provideda better alternative to decompose CCl₂F₂.     

Deposition of Gallium Nitride Thin Films by MOCVD in Microwave Plasma

The deposition of GaN thin films in a nitrogen–hydrogen microwave plasma using Ga(CH ₃ ) ₃ as a gallium precursor was investigated. The deposit was identified as stoichiometric GaN by XPS and XRD. The substrate was dielectrically heated in the microwave discharge and the substrate temperature was lower than that in usual thermal MOCVD. The NH radicals, which were the primary N-atoms precursors, and fragments of Ga(CH ₃ ) ₃ were identified in the plasma by OES. The NH radical formation and the decomposition of Ga(CH ₃ ) ₃ in the plasma may be one of the reasons for the lower deposition temperature of GaN. The position dependence of the substrate temperature showed similar tendency as the position dependence of the electron temperature. The plasma state contributes to the deposition of GaN thin films. The deposited GaN exhibited a wide optical band gap of 3.4eV. Material highly oriented along the c axis was detected in the deposit, and a PL spectrum which has the band head at about 450 mm was obtained.     

Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.     

Hydrocarbon Effects on the Promotion of Non-Thermal Plasma NO–NO2 Conversion

Kinetic modeling of non-thermal plasma chemistry is conducted to investigate hydrocarbon (CH₄, C₂H₄, C₃H₆, and C₃H₈) effects on the promotion of NO–NO₂ conversion. A reduced plasma chemistry model, in which radical reactions are selectively involved, is validated with experimental data. The higher reactivity of hydrocarbon additive with O radicals, which produces initial radicals, is requisite to initiate hydrocarbon decomposition, thus providing NO–NO₂ conversion. Initial radicals by plasma discharge induce continual hydrocarbon decomposition and this self-preserved reaction mechanism greatly contributes to the promotion of energy efficient NO–NO₂ conversion. Increase in the conversion extent by ethylene and propylene additives is substantial because of their stronger affinity with O radical. The primary routes of NO–NO₂ conversion process differed by hydrocarbon additives are presented and discussed with the assistance of sensitivity analysis.     

Numerical method and composition in multi-temperature plasmas: Application to an Ar-H2 mixture

To take into account the nonequilibrium between the temperatures (electronic, rotation, vibration, translation) in plasmas, the partition function are modified. Then they are used to determine the concentration in a Gibbs free energy minimization method adopted to a multi-temperature plasma. Their influence oil the results for different temperature hypotheses is quantified. The composition and thermodynamic properties of an Ar-H₂ mixture are given and discussed for different temperature nonequilibria.     

The reaction of MgCl2·4H2O with CCl2F2

A new reaction of MgCl₂·4H₂O with CCl₂F₂ is investigated by DTA and TG from room temperature to 350 °C. It is observed that MgF₂ was obtained between 252 and 350 °C, Below the temperature, MgCl₂·4H₂O dehydrates and hydrolyzes to MgCl₂ and Mg(OH)Cl, which are the real reactants of the reaction with CCl₂F₂. The formation of MgF₂ is ascribed to the reaction of MgCl₂ and Mg(OH)Cl with HF, which forms by decomposition of CCl₂F₂ with the taking part in of H₂O released from dehydration of hydrated magnesium chloride on the surface of MgCl₂ and Mg(OH)Cl, which catalyzes the decomposition of CCl₂F₂ in this case. Consequently, the reactions are tested in the fluid-bed condition. It is found that MgF₂ formed at temperatures down to 200 °C in a fluid-bed reactor. This reaction may be used as a method of disposing of the environmentally sensitive CCl₂F₂ (rather than release into the atmosphere). It is also a method for the preparation of MgF₂.     

基于密度泛函理论对等离子体中H/CO2相互作用的第一性原理研究

深入理解辐照条件下氢同位素与CO₂反应的微观机制,可为聚变堆氘氚燃料循环工艺的优化设计提供数据支撑。基于此,采用第一性原理计算研究了等离子体放电条件下H₂和CO₂的微观反应机制,研究了不同温度和氢同位素效应对反应过程的影响。通过内禀反应坐标（IRC）算法结合反应过渡态获得4条初始反应路径,并对比研究了生成产物CH₄及CH₃OH的2条路径在热力学上的容易程度,以及不同氢同位素对各个反应的影响。研究发现,氚的自发衰变或等离子体中的高能电子都会诱导氢同位素与CO₂发生反应,形成CO、H₂O、CH₄及CH₃OH等产物;在高能电子诱导CO₂的离解后,由4条初始反应路径组成的复杂反应可以自持发生,且该复杂反应中存在2种倾向;升高反应温度对CO₂转化为有机物（CH₄和CH₃OH）具有一定的促进作用。     

Hydrogen desorption of reduced Pt/TiO2 catalyst

The temperature-programmed desorption of hydrogen from a Pt/TiO₂ catalyst reduced in a wide temperature range (RT-773 K) has been studied. It is found that the presence of labile surface oxygen species increases the amount of hydrogen species formed at room temperature, and greatly decreases the quantities of adsorbed hydrogen species at medium temperatures. After the catalyst was reduced at high temperature, it is observed that two strong hydrogen desorption peaks appear at 450–600 K and above 600 K, which are ascribed to surface titanium hydride and the hydrogen species stored in the sublayer and bulk of the support, respectively.