沸石分子筛的骨架同晶置换(Ⅰ)——NH4BF4溶液中沸石分子筛的脱铝补硅

通过NH₄BF₄溶液对沸石分子筛进行脱铝补硅,对所得产物已用多种技术表征。结果表明,在此处理过程中,产物的硅铝比随溶液中NH₄BF₄浓度的增加而增加,热稳定性随之增强,酸量随之减弱,未发现硼对骨架元素的同晶置换,而发生了脱铝补硅作用。     

NH4BF4改性Y沸石的结构和性质

用NH₄BF₄溶液处理普通的Y沸石后,得到了一系列不含B的脱铝Y沸石。本文运用多种实验手段对它们进行了表征,并与其它改性方法得到的脱铝Y沸石进行比较,发现这类Y沸石脱铝羟基空穴较少,晶格热稳定性较高,且具有特殊的表面酸性分布,因而NH₄BF₄处理亦是一种有特色的Y沸石改性方法。     

(NH4)2SiF6脱铝八面沸石酸性和1-已烯结碳研究

(NH_4)_2SiF_6液相同晶取代脱铝技术,作为沸石脱铝方法之一,自1985年提出后,己引起了人们的广泛注意.研究结果已表明:(NH_4)_2SiF_6脱铝沸石的结晶度很高,二次中孔道很少;由于在脱铝过程中扩散影响较大,使得脱铝沸石晶粒表面富硅.本文由(NH_4)_2SiF_6方法制备了骨架Si/Al 比在2.62～5.20的系列样品,用吡啶吸     

完善骨架全硅β沸石性质研究

以四乙基氢氧化铵为模板剂,正硅酸乙酯为硅源,静置水热法合成全硅β沸石 。用硝酸(13 mol/L)对硅铝比(Si/Al)为20的Na-β沸石回流脱铝。焙烧后的上述两 样品经粉末X射线衍射、低温氮吸附、核磁共振、红外光谱、吸附等温线等表征, 发现合成的全硅β沸石骨架与孔道结构完善并具有很高的表面疏水／亲有机物的吸 附特性。     

完善骨架全硅β沸石性质研究

以四乙基氢氧化铵为模板剂，正硅酸乙酯为硅源，静置水热法合成全硅β沸石 。用硝酸(13 mol/L)对硅铝比(Si/Al)为20的Na-β沸石回流脱铝。焙烧后的上述两 样品经粉末X射线衍射、低温氮吸附、核磁共振、红外光谱、吸附等温线等表征， 发现合成的全硅β沸石骨架与孔道结构完善并具有很高的表面疏水／亲有机物的吸 附特性。     

八面沸石用(NH_4)_2SiF_6脱铝补硅的研究 Ⅲ.脱铝补硅沸石的性能

沸石的热稳定性、酸性和催化性能与沸石的Si/Al比有很大的关系.用(NH_4)_2SiF_6对Y型沸石进行脱铝补硅,能改变沸石的Si/Al比,并且脱铝沸石中非骨架铝少,结晶度好,很适合用于研究其物化性质与催化性能随Si/Al比的变化. 样品的制备及结构参数测试参阅文献〔1〕.沸石的组分分析采用湿法化学分析法。晶格破坏温度由DTA法测定.将厚度为10mg/cm~2的片状沸石,于1.33×10~(-2)～     

高酸位多级孔超稳Y型沸石的制备及催化性能

以表面活性剂十六烷基三甲基溴化铵(CTABr)为模板剂,在水热体系对水蒸气处理后的超稳Y型(USY)沸石进行晶化处理,获得高酸量和高水热稳定性的USY-c-w样品。利用X射线衍射、扫描电子显微镜、透射电子显微镜、固态核磁共振、N₂吸附-脱附、NH₃-程序升温脱附、傅里叶变换红外光谱及吡啶红外对所制备催化剂的物化性质进行详细表征。选用1,3,5-三异丙苯(TIPB)催化裂化作为探针反应,研究制备的催化剂的催化性能,并与工业USY沸石进行对比。结果表明,再次水热晶化后,样品的硅铝骨架局部重构,非骨架铝重新进入沸石骨架,合成样品的硅铝比(n_Si/n_Al)由10降至3.0;再晶化后的USY沸石,不仅具有丰富的介孔结构,并且具有更多的弱酸和中强酸位点。在TIPB裂解反应中,再晶化后的USY沸石表现出比原样品更优异的催化性能。     

模板剂四乙基氢氧化铵的用量对合成的β沸石结构及脱胺的影响

研究四乙基氢氧化铵（TEA-OH）模板剂用量对合成的β沸石的结构及脱胺行为的影响。合成β沸石的模板剂的较佳用量(TEA+/Al)为2.10～1.68,合成的β沸石的相对结晶度均大于84%;β沸石中的铝含量(Al/Al+Si)及骨架铝含量(TdAl/TdAl+OhAl)随晶化混合液的TEA+/Al而变,存在最佳TEA+/Al点为1.9,此时合成的β沸石非骨架铝量最少,结构硅铝比最高;含TEA的β沸石脱胺过程为Hofmann降解反应,TGA测定的失重量、DSC测定的吸热量与β沸石中TEA含量密切相关.     

脱铝八面沸石的研究II.羟基及其酸性

采用SiCl_4同晶取代NaY沸石,制备了硅铝比变化较宽且结晶度完好的八面沸石,进一步将样品交换为铵型,还制备了铝交换型八面沸石及越稳Y样品。红外研究发现,随硅铝比增加,八面沸石样品的两种典型羟基谱带频率发生规律性变化,且于3600及3666cm~(-1)附近相继出现新的羟基吸收谱带,其小笼羟基质子酸性逐渐增加,沸石体系B酸总量逐渐降低,而强B酸量则呈山峰形变化,骨架外铝对硅铝比较低的样品的酸性影响较大,在骨架硅铝比相近情况下,高温水热法脱铝样品(USY)较SiCl_4脱铝样品(DNH_4Y)的羟基谱带和酸性具有明显的差异。     

脱铝八面沸石的研究I.制备及表征

以NaY沸石为原料,采用SiCl_4同晶取代脱铝技术,制得了硅铝比变化范围较宽的八面沸石,所得样品结晶度高且系列性好。用XRD测定沸石的晶相、晶胞参数α_0和峰相对强度,以IR测定沸石的骨架振动谱带。系统地研究了制备条件对脱铝产品性能的影响,并对取代过程的化学原理进行了探讨。     

Methane dehydrogenation and aromatization in the absence of oxygen on Mo/HZSM-5: A study on the interaction between Mo species and HZSM-5 by using Al and Si MAS NMR

By using a high-resolution solid state nuclear magnetic resonance spectrometer with ²⁷Al and ²⁹Si probes, the interaction between Mo species and HZSM-5 of frsol|Mo/HZSM-5 catalysts has been studied. The results show that there is a strong interaction between Mo species and HZSM-5 zeolite. The framework aluminum in the zeolite can be easily extracted by the introduction of Mo species. The extractability of framework aluminum by Mo species increases with increasing Mo loading and the calcination temperature. The extraction process leads to the formation of non-framework Al at first and then a new crystalline phase of Al₂(MoO₄)₃. The dealumination of the catalyst having a Mo loading of 15% and had been calcined at 973 K is so severe that all the aluminum in the framework are extracted and no framework Al could be detected by ²⁷Al MAS NMR. The catalyst, therefore, lost its catalytic activity for methane dehydrogenation and aromatization in the absence of oxygen. The Si/Al ratio measured from ²⁹Si MAS NMR further confirms the dealumination process observed by ²⁷Al MAS NMR. The MAS NMR results give us an evidence that Al₂(MoO₄)₃ crystallites are much less active for the reaction.     

镁改性对HZSM-5分子筛催化乙烯制丙烯的影响

采用等体积浸渍法制备了一系列不同Mg含量(0–1.0%)的HZSM-5分子筛。利用X射线衍射(XRD)、N_2吸附/脱附、铝魔角旋转固体核磁共振(~(27)AlMASNMR)、~(29)SiMASNMR、氨-程序升温脱附(NH_3-TPD)和吡啶吸附傅里叶变换红外(Pyridine-IR)光谱等技术对改性前后样品的结构和酸性进行了详细表征,在常压连续流动固定床反应器上考察其对乙烯转化制丙烯(ETP)反应的催化性能,评价了反应条件和Mg改性的影响。结果表明,在温度为550°C、乙烯体积空速GHSV=3000 h~(-1)的适宜反应条件下,0.5%适量镁改性HZSM-5导致乙烯转化率有所下降,但丙烯选择性增加到45%以上,而副产物芳烃的选择性降到8%以下。反应前样品的酸性表征和反应后积碳样品的TPO及~(13)CCP/MASNMR谱图分析表明适量镁改性使HZSM-5分子筛的总酸量和强B酸量减少而中强酸量增加,从而提高了丙烯的选择性,但是过量的镁改性使分子筛的总酸量明显减少,导致催化剂的活性显著下降。     

A high-resolution MAS NMR study on the potential catalysts Mo/HBeta for olefin metathesis: The interaction of Mo species with HBeta zeolite

The interfacial interaction of Mo species with the HBeta zeolite was studied by multinuclear MAS NMR, XRD and N₂ adsorption. As proved by the quantitative ²⁷Al MAS NMR, this interaction is so strong as to dealuminate the framework of HBeta, and leads to a new peak appearing at −14 ppm, which indicates the formation of crystalline Al₂(MoO₄)₃. This can also be detected by XRD measurements when the Mo loading is as high as 9.0 wt.%. The corresponding quantitative ²⁹Si and ¹H MAS NMR spectra show that the amount of silanols and Brønsted acidic sites decrease obviously with increasing Mo loading. This also reveals an interaction between Mo species and HBeta support through an oxygen bridge resulting from condensation with the hydroxyls on the support. At higher Mo loadings, the interaction is so strong that it results in an extraction of aluminum from the zeolite framework, and subsequently appearance of Al₂(MoO₄)₃ and loss of Brønsted acidic sites. These can be correlated to the low catalytic activity of Mo/HBeta in metathesis of ethylene and 2-butylene to propylene.     

^29Si（^27Al）MAS NMR考察镧离子在LaDAlY型沸石中的作用

用~(29)Si(~(27)Al)MAS NMR和辅加乙酰丙酮(acac)处理样品的静态~(27)Al NMR研究了镧离子对脱铝Y型沸石(DAIY)骨架硅、铝和非骨架铝(EFAL)的影响.结果表明,~(29)Si MAS谱的化学位移及其形状不仅取决于连接[SiO_4]四面体的[AlO]-四面体数目,而且还与引入镧离子的量有关.镧离子的引入导致~(27)Al MAS谱的明显宽化和不对称形变.另外,还讨论了镧离子对非骨架铝的影响.     

Structural evolution of calcium-exchanged (NH4)2SiF6-dealuminated Y zeolite after various chemical treatments

The structural evolution of Y zeolite (Si/Al 2.17) weakly dealuminated by hexafluorosilicate (Si/Al 3.13), denoted Y_D, and exchanged with calcium (CaY_D), has been studied after acid–base treatments at 80 °C close to the cation exchange conditions. The stability of the samples was followed by X-ray diffraction and solid-state NMR of ²⁹Si and ²⁷Al; Y_D zeolite was completely destroyed by treatment with acid pH 2.5 and suffered serious degradation on treatment with alkali at pH 11.8. The introduction of calcium improved the stability of the zeolite in acid and base. In acid CaY_D was not destroyed until pH 1. At pH 2, silicon and aluminium were extracted and an amorphous phase was formed. Base treatment at pH 13 did not affect the calcium-exchanged zeolite.     

DFT计算结合固体NMR研究富铝SSZ-13的铝分布和Br?nsted酸性

具有菱沸石(CHA)结构的SSZ-13分子筛在甲醇制烯烃(MTO)及柴油机车尾气氨选择性催化还原(NH_3-SCR)反应中具有重要的应用,采用富铝SSZ-13可以调节MTO反应的烯烃选择性和提升NH_3-SCR的低温脱硝活性,因此SSZ-13中的铝含量和分布与对应的酸性决定了其催化性能。本文采用密度泛函理论结合固体核磁共振实验研究了富铝和富硅HSSZ-13的Al位置与Br?nsted酸强度的内在关系。通过计算取代能发现,对于孤立Al位,质子位于Al周围4个不同O位时能量差异较小,最稳定的B酸位点是O(1)―H。对于富铝SSZ-13,两个Al原子位于同一六元环的对位是Al-Si-Si-Al (NNNN)序列中最稳定的结构,而Al-Si-Al (NNN)序列中能量最优的Al分布是两个铝原子排布于六棱柱上下不同的六元环上。通过计算最稳定构型下的质子亲和势、NH3脱附能和吸附氘代乙腈后的1H NMR化学位移,发现富铝SSZ-13中含有Si(2Al)分布的NNN序列导致了其Br?nsted酸强度弱于高硅的分子筛。分峰拟合29Si魔角旋转核磁共振(MASNMR)谱图表明富铝SSZ-13中Si(2Al)的含量在43%以上,而吸附氘代乙腈后的1H MAS NMR实验显示富铝SSZ-13的桥羟基化学位移向低场移动,进一步证明富铝SSZ-13具有较弱的Br?nsted酸强度。     

NMR Study of Pore Surface and Size in a Mesoporous Material FSM-16

Surface structure, pore size distribution and pore wall thickness of a mesoporous material FSM-16 have been studied by X-ray powder diffraction (XRD), ^lH and ²⁹Si MAS NMR and ¹H liquid-state NMR, and by applying surface silylation as a probe. Concentrations of surface hydroxyl groups for FSM-16 are estimated from ²⁹Si and ¹H MAS NMR, which are about 3×l0²¹ g^-1, corresponding to approximately 3 nm^-2. O₂ molecules contribute to ²⁹Si spin-lattice relaxation of Q² and Q³ as well as Q⁴, suggesting thin wall thickness. ¹H MAS NMR spectra indicate the presence of isolated and hydrogen-bonded hydroxyl groups. Both hydroxyl groups are silylated, where the silylated fraction is about 50%. The spatial distribution of surface hydroxyl groups is estimated from the line width in ¹H static spectra. A rather homogeneous distribution is demonstrated in one of the samples. The sample with less homogeneous distribution has a larger affinity for moisture. Pore size and pore wall thickness were determined by ¹H NMR measurements on water saturated FSM-16 samples, which are in good agreement with literature values obtained by N₂ adsorption isotherms and transmission electron micrographs on a similar sample. In benzene saturated samples, a non-freezing surface layer of benzene is much thicker than that of water, which indicates a stronger interaction between benzene and the FSM-16 surface.     

ZSM-5酸改性对甲醇芳构化性能的影响

利用硝酸、草酸和酒石酸溶液对ZSM-5分子筛进行改性,并采用XRD、SEM、NH₃-TPD、XRF、²⁷Al MAS NMR、吡啶吸附红外光谱和N₂吸附-脱附对ZSM-5分子筛结构、酸量、比表面积及孔体积等物化性质进行表征分析。在反应温度为422℃,甲醇质量空速为4.74 h^-1的条件下,考察了ZSM-5分子筛的催化活性。结果表明,采用不同酸改性ZSM-5分子筛,影响了分子筛的比表面积、酸性及孔体积,从而改变了催化剂的催化性能。在甲醇芳构化（MTA）反应中,酸改性后的分子筛表现出良好的催化活性,且草酸改性后的催化剂表现出较高的催化活性及选择性,反应8 h时,芳烃及BTX收率分别达到57.40%和39.40%。     

纳米富铝β沸石的合成与表征

以低硅铝比焙烧后的硅铝胶固体为初始原料,在含F-近中性与低含水量体系下晶化合成出相对高结晶度的纳米富铝β沸石。实验考察了合成条件、硅铝胶焙烧对晶化产物的影响和晶化过程中Al配位状况变化,并采用XRD、XRF、SEM/TEM2、7AlMAS NMR物化方法对晶化产物进行表征。结果表明,含F-离子、H2O/SiO2摩尔比为2.4～6.0以及高温焙烧硅铝胶有利于合成高结晶度的纳米富铝β沸石;硅铝胶固体焙烧后能产生易于转化为β沸石晶核的Al四配位结构,而部分六配位Al在晶化过程中缓慢溶入β沸石晶核中而最终生成纳米富铝β沸石。     

REUSY-Ex的吸附性能及二次孔结构研究

应用高真空重量法(分别以苯和正庚烷为吸附质)和低温N2吸附法对REUSY-Ex的吸附性能和二次孔结构进行了研究.结果表明,在水热处理过程中可产生二次孔结构,且二次孔的形成与水热处理的脱铝深度相关.稀HCl浸取REUSY不仅能浸取出位于其二次孔中的非骨架铝(EFAL)碎片,而且还能浸取出位于微孔中的EFAL。29Si MAS NMR的结果显示,稀HCl浸取后,骨架Si(OAl)的谱宽变窄,裂分效果提高,表明其化学环境单一或均匀.