低阶煤热萃取物与瘦煤共炭化焦炭的微观结构及显微强度研究

以众唯瘦煤作为主炼焦煤,大同长焰煤萃取物作为添加剂,进行共炭化处理制备坩埚焦。利用偏光显微镜法定量研究焦炭光学显微组分,获得焦炭的各向异性指数(DRAS);采用XRD及分峰拟合的方法研究了焦炭的微晶粒径(L_c)、芳香缩合度(I_a)、石墨化度(g);利用Raman光谱结合分峰拟合的方法研究了焦炭中理想石墨微晶含量(I_g)。对所得焦炭的光学显微组分进行定量分析发现:大同长焰煤热解萃取产物的添加对共炭化焦炭的光学显微组分有显著的影响,利用偏光显微镜法计算出焦炭的DRAS与XRD和Raman计算的焦炭微晶参数呈现很好一致性。并且,焦炭的显微强度与其微观结构关联性极大。     

用光学显微术和X-射线衍射法研究焦炭结构

用X-射线衍射测定了具有各种不同光学组织(从各向同性到直径大于60μm 的广域)的24种焦炭。研究了光学组织指数(OTI)与微晶高度和面间距之间的关系。对于光学组织中大于中粒锒嵌(1.5—5.0μm)的焦炭,其OTI 值随X-射线衍射指数的变化很小。对于光学组织中结构很小的焦炭,则微晶高度急剧下降和面间距增加。这些结果可以解释为当生成中粒锒嵌焦炭时,流动中间相融并,消除了缺陷。而光学组织尺寸较小的焦炭则是未经融并,因此缺陷残存于焦炭中,从而降低了结晶化程度。     

聚合物热裂解碳材料结构对电化学性能的影响

近年来 ,对各种碳材料如天然石墨、焦炭、碳纤维、非石墨碳、裂解碳、掺杂型碳等用于锂离子二次电池的负极已进行了广泛的研究[17].随着碳材料来源和制备方法的不同 ,其形态和结构差异很大 ,这些宏观和微观结构的变化对锂离子电池碳负极的电化学性能有很大影响 .也就是说锂离子在碳负极材料中的嵌入与脱出能力与碳负极的种类 (石墨碳或非石墨碳 )、形态 (如结晶或非结晶碳 )及比表面积、Ｈ/Ｃ原子比率、粒径大小及其分布、聚集态以及微晶尺寸ｄ0 0 2 、Ｌａ、Ｌｃ 等物理参数均有密切关系 .由于碳材料本身结构的复杂性及其形态的多样性 ,目…     

间规1,2-聚丁二烯结晶结构研究

以间规1,2-聚丁二烯(s-PB)为研究对象,通过原位同步辐射小角X射线散射(SR-SAXS)和广角X射线衍射(WAXD)研究其结晶结构的变化过程.SR-SAXS曲线中存在明显的散射峰,表明在等温结晶过程中形成有序结晶结构;在等温结晶后间规1,2-聚丁二烯的片晶厚度、微晶尺寸均正比于1/Tc∞-T,根据高分子结晶中介相机理可以做出合理的解释.     

弱粘结煤的高温结构变化及其对合成SiC的影响

用弱粘结煤与石英砂以Acheson工艺合成了SiC ,用SEM研究了弱粘结煤高温焦炭的孔隙结构 ,并对弱粘结煤 80 0℃～ 1 60 0℃的焦炭进行了X射线衍射分析 ,计算了各温度下的微晶结构参数。研究表明 ,弱粘结煤高温焦炭孔隙率、长径比和表面积大 ,反应性好 ,可为SiC快速、大范围生长提供有利条件。微晶活化温度范围也和SiC的最佳合成温度范围基本一致。     

交联聚乙烯熔体结晶的晶胞结构及微晶尺寸

用X -衍射方法研究了熔融辐照交联结晶聚乙烯的晶胞结构变化规律 ,并得到了垂直( 110 )晶面方向微晶尺寸随辐射照剂量变化的关系。结果表明晶格尺寸和缺陷随交联度增加而增长。     

炭化程度对核桃壳焦孔隙结构和燃烧特性的影响

利用傅里叶变换红外光谱仪(FT-IR)、扫描电子显微镜(SEM)和X射线衍射仪(XRD)研究了炭化程度对核桃壳焦孔隙及微晶结构的影响,并使用热重-差示扫描量热仪(TG-DSC)对核桃壳焦及其原料的燃烧特性进行了分析。结果表明,合适的炭化程度(焦炭挥发分含量为6%-15%)使焦炭内乱层石墨变得无序,碳质微晶结构中缺陷增多,导致焦炭内孔隙结构相对发达;热解温度为500℃时,核桃壳焦的比表面积最大,为374.60 m~2/g;热解温度为600℃时,核桃壳焦的燃烧特性最优,其燃烧特性指数为7.16×10~6;合适的炭化程度可使焦炭内的挥发分含量减少,从而使得核桃壳焦的高位热值升高,且由于相对发达的孔隙使焦炭在燃烧时与空气的接触面积增大,导致焦炭的燃烧速率加快。     

剪切对iPP/PEcO共混物结晶行为的影响

对剪切场作用下的全同聚丙烯/弹性体乙烯-辛烯共聚物(iPP/PEcO)的共混物结晶行为进行研究, 结果表明, 剪切使得iPP球晶密度增加, 微晶和片晶均发生取向, 且片晶取向明显; 片晶取向度随共混物中PEcO含量的增加而增大, 而微晶取向度随PEcO含量的增加而减小; 强剪切诱导出现纤维状结晶形态. 利用同步辐射(SAXS)技术对共混物在剪切场下的等温结晶行为进行研究, 结果表明, 随结晶的进行长周期呈现先减少而后固定的趋势; 高剪切速率缩短了结晶诱导时间, 加快了共混物中结晶部分的结晶动力学过程.     

乙烯-α-烯烃共聚物的结晶性能及其临界序列结晶长度的研究

本文用DSC、WAXD及偏光显微镜(PLM)方法,研究了化学反应法催化剂合成的乙烯-α-烯烃共聚物的结晶性能及其临界序列结晶长度。结果表明,随共聚物中α-烯烃含量增大,共聚物的微晶尺寸、结晶度及熔点均逐渐减小,而晶胞参数增大。变化的辐度戊烯>辛烯。共聚物的临界结晶序列长度(n)和k值均戊烯<辛烯。上述结果表明影响支链进入晶格的主要因素是α-烯烃支链长度和结构。     

高分子液晶态有序性对其结晶过程的影响

采用退偏振光强度法、ＳＡＬＳ和ＰＯＭ测定了高分子液晶态有序微区结构随体系温度变化的规律,并用ＤＳＣ法研究具有不同有序微区结构尺寸的液晶态的结晶过程．结果发现,高分子液晶态有序性或有序微区结构是随着体系退火温度和时间的变化而变化．同时从相应的不同有序性为起始态进行结晶时,其结晶速率明显不同．并讨论了高分子液晶态的结晶机理     

高硫石油焦高温热解过程及硫析出特性研究

为深入了解高硫石油焦在工业应用高温工况下的热解过程以及硫的析出特性,本研究采用高温固定床对青岛高硫石油焦进行了高温(900-1500℃)热解实验,考察了高温热解下热解气体释放规律,热解过程中焦的物理孔隙结构以及化学特性的演变,并对热解过程中硫的析出与演变特性进行了研究。结果表明,随着热解温度的升高,石油焦热解气中的H₂含量逐渐增加,CO含量变化不大,CH₄与CO₂含量则逐渐下降;热解焦的比表面积与平均孔隙均随热解温度的升高有所增加,颗粒的表面形态则受温度影响较小;热解温度的升高会降低石油焦中含有的非定型碳比例,提高其微晶结构的有序性以及石墨化程度;热解焦的气化活性随热解温度的升高先降低后升高,在1100℃附近有最小值; 1500℃高硫石油焦硫元素析出率达81.34%,仅少量硫醇类有机硫和噻吩环内的硫元素得以残存。     

X-ray analysis of the influence of various nucleating agents on the crystallinity of poly-α-butene

The influence of various nucleating agents on the crystallinity of poly-α-butene form I has been studied. The nucleating agents were: adipic acid, salicylic acid, p-aminobenzoic acid, sodium benzoate and sorbic acid; their influences on the lattice parameters, degree of crystallinity, size of crystallites and texture have been examined. The analysis was carried out by wide-angle X-ray diffraction. The relative degrees of crystallinity in poly-α-butene samples containing nucleating agents were measured using the Hermans-Weidinger procedure; in order to obtain the size of crystallites, the Debye-Scherrer method was applied. The lattice parameters show no change but the relative degree of crystallinity, the size of crystallites and their texture depend on the nucleating agent used.     

高硫石油焦制备高储气性能天然气吸附剂

以高硫石油焦为原料,KOH为活化剂,十二烷基苯磺酸钠（SDBS）为表面活性剂制备天然气吸附剂,分析了高硫焦基吸附剂的孔结构和孔分布特征,讨论了高硫焦制备吸附剂的活化机理。结果表明,预活化中加入表面活性剂SDBS可提高KOH与原料的混合均匀度,对活化效果有利。最优活化条件下制备的吸附剂样品GSR3和GSR4的微孔容积分别达到1.0985cm3·g－1 和1.3193cm3·g－1,孔径分布集中在0.9nm~1.5nm;在25℃、充放气压力3.5MPa和0.1MPa下,GSR3、GSR4对甲烷的质量吸附量分别达到0.139和0.145,有效体积脱附量达到111和115。粉体高硫焦基吸附剂的性能非常接近于低硫焦基吸附剂。     

Supramolecular Structure - A Key Parameter for Cellulose Biodegradation

Summary: Three different cellulosic substrata, like microcrystalline cellulose, cotton cellulose and spruce dissolving pulp, were chosen for biodegradation. The kinetics of the enzymatic hydrolysis of these celluloses by Trichoderma reesei, has been investigated. The experiments proved the fact that both the morphological structure and the crystalline one are crucial to the process and the ratio of the reactions. In addition, in order to obtain the most accessible cellulose substratum it was studied the biodegradation of cellulose allomorphs of spruce dissolving pulp. The insoluble cellulose fraction remaining after enzymatic hydrolysis was examined by X-ray diffraction method and it was established the degree of crystallinity and the average crystallite size. The enzymatic degradation is also proved by the decrease in the degree of polymerization of hydrolyzed samples.     

Thermal compatibility studies of nitroimidazoles and excipients

Nitroimidazoles are heterocycle imidazoles with a nitrogen group incorporated in its structure. The objective of this study was to develop a model to characterize possible interactions between active substances and excipients using: Thermogravimetry, Differential Thermal Analysis, Differential Scanning Calorimetry, and DSC coupled to photovisual system. It was used three nitroimidazoles (metronidazole, secnidazole, and tinidazole) and two types of microcrystalline cellulose with different particle size (Microcel and Avicel). The binary mixtures were prepared in proportion (w/w) 1:1 (nitroimidazole:excipient). Thermogravimetric data demonstrated that the tinidazole was the nitroimidazole with better uniformity. The nitroimidazoles obeyed the zero order kinetic reaction, evidencing its vaporization processes. Differential thermal analysis data showed nitroimidazoles compatibility with the different microcrystalline celluloses studied, showing that microcrystalline celluloses stabilized the active substances. Calorimetric data of secnidazole showed two melting points, characteristic of the polymorphs presented in raw material. The vaporization constants values of nitroimidazoles studied were secnidazole > metronidazole > tinidazole and for the binary mixtures these values followed the order tinidazole > metronidazole ≥ secnidazole.     

渣油加氢转化催化剂初期结焦规律的研究

以孤岛减压渣油及其超临界流体萃取分馏所得的窄馏分为原料,采用齐鲁石化公司胜利炼油厂VRDS装置的主催化剂,在高压釜反应器内考察了渣油加氢转化催化剂的初期结焦规律。结果表明,焦炭的生成是一个动态过程,其产率和性质与反应体系的温度、时间、氢气初始压力及原料的性质密切相关;结焦催化剂的孔壁焦炭沉积和堵孔现象严重,导致其比表面积大大减小,孔分布向小孔范围迁移。     

水溶性Mo催化剂在悬浮床加氢过程中的低温硫化

采用不同的分散及硫化过程,研究了水溶性分散型Mo催化剂在低温（≤300℃）下的预硫化,并对不同条件下形成的硫化态催化剂进行了表征与评价。结果表明,水溶性Mo催化剂（分散破乳）SⅠ方案采取300℃硫化,（共同破乳）SⅡ采用200℃硫化,硫化后催化剂取得较小的粒径分布;催化剂在100℃下硫化可以形成少量MoS2晶体,并且结晶程度低,300℃硫化时两种硫化方案均形成结晶较好的MoS2物种。水溶性Mo催化剂300℃硫化下随着硫化时间的延长,催化剂的抑焦活性增强,但硫化时间大于2h后催化剂抑焦活性趋于稳定,抑焦活性随硫化时间延长的变化趋于平缓。     

Preparation of rapidly disintegrating tablet using new types of microcrystalline cellulose (PH-M series) and low substituted-hydroxypropylcellulose or spherical sugar granules by direct compression method

To decrease the sensation of roughness when a tablet, which is rapidly disintegrated by saliva (rapidly disintegrating tablet), is orally taken, we prepared rapidly disintegrating tablets using microcrystalline cellulose (Avicel PH-M series), a new type of pharmaceutical excipient that is spherical and has a very small particle size (particle size, 7-32 microm), instead of conventional microcrystalline cellulose (PH-102) used in the formulation of tablets containing acetaminophen or ascorbic acid as model drugs for tableting study. Tablets (200 mg) prepared using spherical microcrystalline cellulose, PH-M-06, with the smallest particle size (mean value, 7 microm) had sufficient crushing tolerance (approximately, 8 kg) and were very rapidly, disintegrated (within 15 s) when the mixing ratio of PH-M-06 to low-substituted hydroxypropylcellulose (L-HPC) was 9:1. Sensory evaluation by volunteers showed that PH-M-06 was superior to PH-102 in terms of the feeling of roughness in the mouth. Consequently, it was found that particle size is an important factor for tablet preparation using microcrystalline cellulose. It is possible to prepare drugs such as acetaminophen and ascorbic acid (concentration of approximately 50%) in the tablet form using PH-NM-06 in combination with L-HPC as a good disintegrant at a low compression force (1-6 kN). To solve the problem of poor fluidity in the preparation of these tablets, we investigated the use of spherical sugar granules (Nonpareil, NP-101 (sucrose and starch, composition ratio of 7:3), NP-103 (purified sucrose), NP-107 (purified lactose) and NP-108 (purified D-mannitol)). Rapidly disintegrating tablets can be prepared by the direct compression method when suitable excipients such as fine microcrystalline cellulose (PH-M-06) and spherical sugar granules (NP) are used.     

Effect of surfactants on the structure and texture characteristics of aluminum oxide

The effect of surfactants (polyvinyl alcohol and cetyltrimethylammonium bromide), which were introduced at the aluminum hydroxide synthesis stage, on the structure and texture characteristics of aluminum oxide was studied by a set of physicochemical techniques. The introduction of the above surfactants did not cause considerable changes in the thermal transformations of aluminum hydroxides, but it affected the genesis of the formed carbon. An analysis of the diffuse reflectance spectra and electron micrographs indicated that the aluminum oxide obtained in the presence of polyvinyl alcohol and calcined at 300°C was covered with polyene-type coke. An increase in the treatment temperature to 550°C led to the formation of condensed aromatic coke; in this case, the specific surface area of the sample increased from 125 to 500 m²/g. The samples calcined at 550°C were γ-Al₂O₃ with a unit cell parameter of 7.933 Å and a crystallite size of no more than 30–40 Å. The pore size distribution was bimodal, with maximums at 35–65 and 380–415 Å, regardless of treatment temperature.