气体辅助注射成型表层熔体形成机理的分析

基于等温条件下下幂律流体的流动分析,对圆管气体辅助注射成型过程中影响表层熔体形成的因素进行了分析,指出在等温条件下牛顿流体所形成的表层熔体厚度比值约为0．3,接近试验值0．34－0．37,非牛顿流体的值（＜0．3）小于实际气辅成型值（约0．38）。文中对产生这一偏差的非等温条件下的影响因素进行作了进一步的分析,认为除了熔体温度、模具温度以及气体延迟时间对聚合物表层熔体的形成有重要影响,熔体／气体前沿之间的压力梯度值以及熔体／气体界面之间的剪切应力都对气体穿透过程中表层熔体的形成有重要影响。     

Influence of scale effect and injection speed on morphology and structure of the microinjection molded isotactic polypropylene parts

The morphology and microstructure as well as their forming mechanism of the parts in microinjection molding process are critical. In this work, the coupling effect of scale factor and injection speed on the morphology of the microparts was systematically investigated. Neat isotactic polypropylene parts with thicknesses of 1 mm, 200 μm, and 100 μm were molded at different injection speeds. Polarized light microscope and wide‐angle X‐ray diffraction were used to inspect the microstructures along the sample thickness. In this way, three kinds of typical morphology were observed in the parts, including typical skin‐core structure for the parts with the thickness of 1 mm, noncore shear layer structure for the parts with the thickness of 200 μm, and special skin‐core structure with large fraction of columnar crystal for the parts with the thickness of 100 μm. Most interestingly, it was intuitively and straightforward found that the wall slip occurs when the injection speed exceeds a certain value. Specifically, opposite morphological change trend can be obtained when the parts were molded at different levels of injection speeds. Based on these experimental observations, the formation mechanism was proposed to interpret the morphological evolution. Our work provides a new insight for better understanding the morphology evolution mechanism for microinjection molding parts.     

Development of morphology and properties of injection‐molded bars of HDPE/PA6 blends along flow direction

The structure and mechanical properties of injection‐molded bars of high‐density polyethylene (HDPE)/PA6 blends were studied in this article. The experimental results showed that the morphologies of injection‐molded bars change gradually along the flow direction, which is tightly related to the melt viscosity and processing conditions. The higher melt viscosity, lower mold temperature, and shorter packing time, restricting the macromolecular relaxation, enhance the difference in morphologies and properties at near and far parts of a mold. An injection‐molded bar (namely H2C5), consisting of 75 wt % of HDPE, 20 wt % of PA6, and 5 wt % of compatibilizer (HDPE‐g‐MAH), showed a greater difference in mechanical properties at near and far parts because of its higher melt viscosity. A clear interface between the skin and core layers of near part in it leads to a much higher impact strength than that of far part. And tensile tests show that its tensile strength of near part is higher than that of far part due to the higher orientation degrees of HDPE matrix and PA6 dispersed phase in near part. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 184–195, 2007     

Unexpected molecular weight dependence of shish kebab in water‐assisted injection molded HDPE

As a part of continuous efforts to systematically understand the morphological development in water‐assisted injection molding, high density polyethylene with different molecular weights was molded in this study. Unexpectedly, it was found that shish kebab with high lamellar and molecular orientations was formed in the sample with a lower molecular weight (LMW) rather than in the higher one, especially in the water channel layer. Present finding is obviously inconsistent with the general consensus, that is, higher molecular weight (HMW) polymer is much easier to form preferential orientation in flow field than LMW one. Such anomalous phenomenon is explained by the fact that even though melts experienced the same processing, lower shear rate is practically achieved in HMW sample due to its high viscosity. The result indicates that the flow history in industrial processing method is far from that in laboratory one. Copyright © 2012 John Wiley & Sons, Ltd.     

Crystallization and phase morphology of injection‐molded isotactic polypropylene (iPP)/syndiotactic polypropylene (sPP) blends

The crystallization and phase morphology of the injection‐molded isotactic polypropylene (iPP)/syndiotactic polypylenen (sPP) blends were studied, focusing on the difference between the skin layer and core layer. The distribution of crystallinity of PPs in the blends calculated based upon the DSC results shows an adverse situation when compared with that in the neat polymer samples. For 50/50 wt % iPP/sPP blend, the SEM results indicated that a dispersed structure in the skin layer and a cocontinuous structure in the core layer were observed. A migration phenomenon that the sPP component with lower crystallization temperature and viscosity move to the core layer, whereas the iPP component with higher crystallization temperature and viscosity move to the skin layer, occurred in the iPP/sPP blend during injection molding process. The phenomenon of low viscosity content migrate to the low shear zone may be due to the crystallization‐induced demixing based upon the significant difference of crystallization temperature in the sPP and iPP. This migration caused the composition inhomogeneity in the blend and influenced the accuracy of crystallinity calculated based upon the initial composition. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2948–2955, 2007     

A novel hierarchical crystalline structure of injection-molded bars of linear polymer: co-existence of bending and normal shish–kebab structure

The hierarchy structures and orientation behavior of high-density polyethylene (HDPE) molded by conventional injection molding (CIM) and gas-assisted injection molding (GAIM) were intensively examined by using scanning electronic microscopy (SEM) and 2D wide-angle X-ray diffraction (2D-WAXD). Results show that the spatial variation of crystals across the thickness of sample molded by CIM was characterized by a typical skin–core structure as a result of general shear-induced crystallization. Unusually, the crystalline morphologies of the parts prepared by GAIM, primarily due to the penetration of secondary high-compressed gas that was exerted on the polymer melt during gas injection, featured a richer and fascinating supermolecular structure. Besides, the oriented lamellar structure, general shish–kebab structure, and common spherulites existed in the skin, sub-skin, and gas channel region, respectively; a novel morphology of shish–kebab structure was seen in the sub-skin layer of the GAIM parts of HDPE. This special shish–kebab structure (recognized as “bending shish–kebab”) was neither parallel nor perpendicular to the flow direction but at an angle. Furthermore, there was a clear interface between the bending and the normal shish–kebab structures, which may be very significant for our understanding of the melt flow or polymer rheology under the coupling effect of multi-fluid flow and complex temperature profiles in the GAIM process. Based on experimental observations, a schematic illustration was proposed to interpret the formation mechanism of the bending shish–kebab structure during GAIM process.     

Effect of molding parameters on the properties of PP/PP sandwich injection moldings

The basic characteristics of a sandwich injection molded product depend on the properties of the respective resins that comprise the skin and core layers, and the skin/core resin volume ratio. The characteristics of the core layer resin and the skin/core ratio in particular may vary depending on the injection molding conditions. This report considers the influences that the molding conditions such as injection speed, cylinder temperature, and mold temperature confer on the mechanical properties of the sandwich moldings. The study employed, skin/core resin combinations involving similar and dissimilar materials i.e. homopolymer PP/homopolymer PP and homopolymer PP/copolymer PP, respectively. It was demonstrated that core cylinder temperature and mold temperature could be used to adjust the mechanical properties of sandwich injection moldings. In the case of single material sandwich moldings, injection speed seemed to play no significant role, even though it was clearly demonstrated that core volume increases with injection speed. However, core injection speed plays a significant role in the dual material system by lowering or increasing the mechanical strength of moldings as the case may be. Thus, the dormant or active role of injection speed depending on the material system has been highlighted.     

Morphology evolution and crystalline structure of controlled‐rheology polypropylene in micro‐injection molding

In this paper, the microstructural evolution of controlled‐rheology polypropylene (CRPP) with different melt viscoelasticities was investigated by polarized optical microscopy, scanning electronic microscopy, differential scanning calorimeter, and wide‐angle X‐ray diffraction. It is found that a typical “skin‐core” structure formed in CRPP microparts and the thickness of oriented layer of CRPP microparts decreases notably with the addition of peroxide. The thickness of oriented layer and the distribution of different layers strongly depend on the melt flow properties and the corresponding relaxation time (λ). Furthermore, the mechanisms of the suppressed formation of oriented layers during the micro‐injection molding process are discussed mainly from the viewpoint of rheology and thermodynamics. It is revealed that the shear‐induced orientation is one of the key factors for the formation of oriented molecular structure (row nuclei). The final thickness of the oriented layer is the result of the competition between the orientation behavior and the disorientation behavior. Copyright © 2015 John Wiley & Sons, Ltd.     

Hierarchical crystalline structures and dynamic mechanical properties of injection‐molded bars of HDPE: attributes of temperature field

The relationship among the processing parameters, crystalline morphologies and mechanical properties of injected‐molded bar becomes much complicated primarily due to the existence of temperature gradient coupled with the shear gradient along the sample thickness. The effect of thermal gradient field on the microstructural evolution, hierarchical structures and dynamic mechanical properties of high‐density polyethylene parts molded via gas‐assisted injection molding (GAIM) were investigated using scanning electron microscope, differential scanning calorimetry, dynamic mechanical analysis and two‐dimensional wide‐angle X‐ray diffraction. The three‐dimensional temperature profiles during the cooling stage under different melt temperatures of GAIM process were obtained by using a transient heat transfer model of the enthalpy transformation approach, and the phase‐change plateaus were clearly observed in the cooling curves. It was found that a variety of melt temperatures could induce considerable variations of the hierarchical structures, orientation behavior and dynamic mechanical properties of the injection‐molded bars. With reduced melt temperature, GAIM samples with higher molecular orientation and improved dynamic mechanical properties were obtained. Copyright © 2013 John Wiley & Sons, Ltd.     

聚烯烃共混物注射制品的形态控制与多层次结构

从注射制品形态控制和结构表征的角度探讨高分子材料加工-形态-性能之间的关系.研究中采用动态保压成型方法来制备注射样品,在注射成型过程中引入剪切应力场的作用,制得的样品表现出明显的多层次结构,从外向里分别为皮层、剪切层、芯层,表现出不同的相形态、结晶形貌以及取向行为.研究发现,剪切应力对聚烯烃的形态发展和结构变化具有重要影响.在剪切应力的作用下,聚烯烃共混物中分散相会发生变形、取向,从而导致共混物的相转变点发生移动;结晶形态从球晶转变为shish-kebab结构;聚烯烃共混物在高剪切应力下相容,低剪切下发生相分离;HDPE/PP共混物的注射制品中出现附生结晶等现象.     

A study on the micro‐injection molding of multi‐cavity ultra‐thin parts

In this study, we report the micro‐injection molding of ultra‐thin parts (100, 250, and 500 µm). The results show that the flow resistance increases as the cavity becomes thinner. The melt front is not symmetric when filling a four‐cavity ultra‐thin part and filling the eight‐cavity mold under a low temperature. If we increase the mold temperature or cavity thickness, the melt front becomes symmetric. Finally, we construct the operation windows of molding for three kinds of plastics (PS, PMMA, PC) and provide a molding range based on mold temperature and injections speed. Meanwhile, the relationship between the thickness and the operation windows are also investigated. The thinner the cavity is, the smaller the operation window is. We need to increase the injection speed significantly for molding the ultra‐thin parts with micro‐features on both surfaces which are 60 µm in thickness. Furthermore, we succeed in molding 30 µm ultra‐thin parts in this experiment. Copyright © 2009 John Wiley & Sons, Ltd.     

Morphological comparison of isotactic polypropylene parts prepared by micro‐injection molding and conventional injection molding

The morphological feature of microparts evolved during micro‐injection molding may differ from that of the macroparts prepared by conventional injection molding, resulting in specific physical properties. In this study, isotactic polypropylene (iPP) microparts with 200 µm thickness and macroparts with 2000 µm thickness were prepared, and their morphological comparison was investigated by means of polarized light microscopy (PLM), scanning electron microscopy (SEM), differential scanning calorimeter (DSC), and wide‐angle X‐ray diffraction (WAXD). The results presented some similarities and differences. PLM observations showed that the through‐the thickness‐morphology of micropart exhibited a similar “skin–core” structure as macropart, but presented a large fraction of shear layer in comparison to the macropart which presented a large fraction of core layer. The SEM observation of shear layer of micropart featured highly oriented shish‐kebab structure. The micropart had a more homogeneous distribution of lamellae thickness. The degree of crystallinity of the micropart was found to be higher than that of the macropart. High content of β‐crystal was found in micropart. The 2D WAXD pattern of the core layer of macropart showed full Debye rings indicating a random orientation, while the arcing of the shear layer indicates a pronounced orientation. The most pronounced arcing of the micropart indicates the most pronounced orientation of iPP chains within lamellae. Copyright © 2011 John Wiley & Sons, Ltd.     

Poiseuille/squeeze flow-induced crystallization in microinjection-compression molded isotactic polypropylene

Microinjection-compression molding was used to fabricate isotactic polypropylene part with microscale thickness. The combined effect of shear (up to the order of 10⁵ s⁻¹) and elongational deformations imposed by the Poiseuille (injection stage) and squeeze (compression stage) flow resulted in pronounced flow-induced crystallization under rapid quenching. Hierarchical crystalline morphology, characterized by two oriented layers, a transitional layer in between, and an isotropic core layer, was detected through the thickness in the upstream region initially filled in injection stage, whereas skin-core morphology appeared in the downstream region filled in subsequent compression stage. Under the molding conditions imposing sufficient strain rates, predominant shish-kebabs developed in the oriented layer. Furthermore, the oriented layer thicknesses, crystallinity, β-form content, and melting behavior of molded parts, all of which were closely correlated with the calculated strain rates, as well as the location of inner oriented layer could be manipulated via varying the compression-related parameters. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Use of Thermoplastic Starch in Continuous Pharmaceutical Process

Controlled release formulations of thermoplastic starch (TPS) matrix were prepared by extrusion granulation and injection molding of tablets. The compositions contained glycerol, water and on occasion urea plasticizers, glycerol-monostearate; Ca-stearate lubricants and Na-benzoate drug representing component, in addition to the starch. The lubricants and especially the urea reduce the complex viscosity of the TPS considerably facilitating the injection molding process-ability. DSC thermal analysis demonstrated, the urea is in a molecular dispersed form in the extruded granules and Raman microscopic mapping showed an under micron sized dispersion of Na-benzoate in injection molded tablets. Both the extrusion and the injection molding processing resulted retard release character of the active component.     

Predicting the location of weld line in microinjection‐molded polyethylene via molecular orientation distribution

The microstructure and molecular orientation distribution over both the length and the thickness of microinjection‐molded linear low‐density polyethylene with a weld line were characterized as a function of processing parameters using small‐angle X‐ray scattering and wide‐angle X‐ray diffraction techniques. The weld line was introduced via recombination of two separated melt streams with an angle of 180° to each other in injection molding. The lamellar structure was found to be related to the mold temperature strongly but the injection velocity and the melt temperature slightly. Furthermore, the distributions of molecular orientation at different molding conditions and different positions in the cross section of molded samples were derived from Hermans equation. The degree of orientation of polymeric chains and the thickness of oriented layers decrease considerably with an increase of both mold temperature and melt temperature, which could be explained by the stress relaxation of sheared chains and the reduced melt viscosity, respectively. The level of molecular orientation was found to be lowest in the weld line when varying injection velocity, mold temperature, and melt temperature, thus providing an effective means to identify the position of weld line induced by flow obstacles during injection‐molding process. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1705–1715     

水辅助注塑PP/SAN共混物制品中横晶形成机理的研究

采用水辅助注塑(WAIM)设备,在不同的注水压力和熔体温度下制备了4种质量比(98/2,96/4,94/6和92/8)的聚丙烯/丙烯腈-苯乙烯共聚物(PP/SAN)共混物制品.采用偏光显微镜(POM)和扫描电子显微镜(SEM),研究了WAIM PP/SAN共混物制品的结晶形态和相形态.研究发现,高压水的穿透作用所引起的强剪切和快速冷却可诱导SAN在PP基体中原位成纤,并诱导PP在SAN纤维表面形成大量的晶核而最终形成横晶.SAN含量为4 wt%时,所形成横晶的含量随水压的提高而增加,随温度的降低而大幅增加.当SAN含量较低(2 wt%)时,制品中没有横晶形成.     

气辅注塑CAE模拟技术的理论基础及分析实例

阐述了CAE模拟技术在气体辅助注射成型模具设计过程中的重要意义；介绍了气体辅助注射成型充填流动分析及保压分析中塑料熔体所遵循的数学模型和粘度参数模型，并介绍了在粘性流体力学基础上对数学模型进行了合理的简化和假设的方法；运用CAE软件C—MOLD对汽车保险杠模具结构设计及成型工艺条件进行了气辅注射成型模拟分析，优化了气体充填成型工艺和充填效果，改善了制品表面质量和力学性能，提高了首试成功率。     

在低频振动场中注射成型HDPE试样的力学性能及其形态控制

利用自行研制的低频振动注射实验装置探讨HDPE振动注射试样力学性能和微观形态之间的关系 .实验中对常规注射和振动注射成型的试样力学性能和微观形态进行了对比实验 .SEM实验结果显示 ,振动注射制件芯层的形态由常规注射的球晶转变为垂直于振动波传递方向排列的片晶结构 ,在剪切层中同时存在串晶或柱状堆砌的片晶结构 .频率的改变 (0 相似文献   

Microinjection molding of polyamide 6

Processing polymers by microinjection molding (μIM) generate specific constraints upon the polymer melt such as high shear stress and rapid cooling, leaving a mark upon the microstructure of the micropart. The present work compares the morphology and structure of polyamide 6 samples produced by melt extrusion and μIM. The specimens obtained were analyzed by polarized light microscopy, differential scanning calorimetry, and wide‐angle X‐ray diffraction. α and γ crystalline forms were formed in polyamide 6 samples prepared by both methods. The γ form was dominant in the skin of the microinjection molded part, with larger contribution for these samples compared with extruded samples. The conditions used in μIM lead to considerable orientation at the skin region, decreasing toward the core, while the extruded samples showed almost no orientation. The overall degree of crystallinity of the microinjection molded part was lower compared with the extruded sample. Copyright © 2014 John Wiley & Sons, Ltd.     

Structure Evolution upon Uniaxial Drawing Skin‐ and Core‐Layers of Injection‐Molded Isotactic Polypropylene by In Situ Synchrotron X‐ray Scattering

The structure evolution of the oriented layer (skin) and unoriented layer (core) from injection‐molded isotactic polypropylene samples upon uniaxial drawing is probed by in situ synchrotron X‐ray scattering. The X‐ray data analysis approach, called “halo method”, is used to semiquantitatively identify the transformation process of crystal phase upon uniaxial drawing. The results verify the validation of the stress‐induced crystal fragmentation and recrystallization process in the deformation of the injection‐molded samples under different temperatures. Furthermore, the end of strain softening region in the engineering stress‐strain curves explicitly corresponds to the transition point from the stress‐induced crystal fragmentation to recrystallization process. Basically, the skin and core layers of the injection‐molded parts share the similar deformation mechanism as aforementioned. The stretching temperature which dramatically affects the relative strength between the entanglement‐induced tie chains and the adjacent crystalline lamellae determines the crystal structural evolution upon drawing. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013, 51, 1618–1631