Synthesis,rheology, and morphology of nylon‐11/layered silicate nanocomposite

Exfoliated nylon‐11/layered silicate nanocomposites were prepared via in situ polymerization by dispersing organoclay in 11‐aminoundecanoic acid monomer. The original clay was modified by a novel method with 11‐aminoundecanoic acid. In situ Fourier transform infrared spectroscopy results show that stronger hydrogen bonds exist between nylon‐11 and organoclay than that of between nylon‐11 and original clay. The linear dynamic viscoelasticity of organoclay nanocomposites was investigated. Before taking rheological measurements, the exfoliated and intercalating structures and the thermal properties were characterized using X‐ray diffraction, transmission electron microscopy, differential scanning calorimetry, and thermogravimetric analysis. The results show that the clay was uniformly distributed in nylon‐11 matrix during in situ polymerization of clay with 4 wt % or less. The presence of clay in nylon‐11 matrix increased the crystallization temperature and the thermal stability of nanocomposites prepared. Rheological properties such as storage modulus, loss modulus, and relative viscosity have close relationship with the dispersion favorably compatible with the organically modified clay. Comparing with neat nylon‐11, the nanocomposites show much higher dynamic modulus and stronger shear thinning behavior. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2161–2172, 2006     

Effect of organoclay loading and electron beam irradiation on the physico‐mechanical properties of low‐density polyethylene/ethylene‐vinyl acetate blend

The influence of electron beam (EB) irradiation and organoclay (OC) loading on the properties of low‐density polyethylene (LDPE)/ethylene‐vinyl acetate (EVA) blends was investigated. The samples were subjected to the EB irradiation with the dose values of 50 and 250 kGy. X‐ray diffraction (XRD), gel content, mechanical, thermal, and electrical properties were utilized to analyze the characteristics of the LDPE/EVA blends with and without OC at different irradiation dosages. Gel content analysis showed that the OC promotes considerably the insoluble part so that the LDPE/EVA blends filled with OC become fully crosslinked at 250 kGy; possibly through the formation of further crosslinks between OC and polymer chains. The samples irradiated by EB showed enhanced mechanical properties due to the formation of three‐dimensional networks. In addition, thermogravimetric analysis indicated that combined OC loading and radiation‐induced crosslinking improved thermal stability of LDPE/EVA blends considerably. Copyright © 2011 John Wiley & Sons, Ltd.     

Fluorene‐based polyester nanocomposites via in situ interlayer polymerization

Fluorene‐based polyester nanocomposites were prepared by in situ polymerization of equivalent weights of 9,9′‐dihexylfluorene‐2,7‐dicarboxylic acid and 4,4′‐dihydroxy‐1,4‐diphenoxybutane (DPB‐OH) in the presence of octadecyl‐montmorillonite (C₁₈‐MMT) as an organoclay. We investigated the intercalation of the organoclay among the polymer chains, with the aim of improving the thermal properties of the polyester. It was found that the addition of only a small amount of organoclay was enough to improve the polyester's thermal properties. The maximum enhancement of the thermal properties of the fluorene‐based polyester nanocomposites was observed with the dispersion of 5 wt% organoclay. Copyright © 2008 John Wiley & Sons, Ltd.     

Characterization of polysuccinate and hydroxyapatite‐based nanocomposites containing poly(ester‐anhydride) microspheres

Repair and regeneration of bone defects with particular shape may be enhanced by in situ forming biomaterials which can be used in minimal invasive surgery. This study is aimed to prepare novel in situ forming biodegradable nanocomposites based on poly(3‐allyloxy‐1,2‐propylene) succinate (PSAGE) and nanosized hydroxyapatite (HA). These nanocomposite materials contain poly(ester‐anhydride) (PEA) microspheres embedded in a polyester matrix prepared by crosslinking PSAGE with oligo(1,2‐propylene maleate) and methacrylic monomers. Methyl methacrylate and one of hydrophilic oligo(ethylene glycol) methacrylates with different functionality and various length of oligooxyethylene chains were used as polymerizable diluents. Incorporation of microspheres which degrade faster than crosslinked polyester matrices enables formation of porous structure in situ. The obtained materials are liquid before curing and harden in several minutes with moderate exothermic effect. The effect of the composition of nanocomposite materials on selected properties, such as water sorption, mechanical strength, porosity and hydrolytic degradation process, was investigated. Rheological behavior and injectability of liquid formulations were studied. Analysis by energy dispersive spectroscopy confirmed the presence of characteristic features of HA in the nanocomposite materials. The morphology of the cured nanocomposites subjected to hydrolytic degradation was evaluated by scanning electron microscopy. The MTS cytotoxicity assay was carried out for extracts from crosslinked materials using hFOB1.19 cells. It was found that the extracts exhibit a dose‐dependent cytotoxic response. Copyright © 2014 John Wiley & Sons, Ltd.     

Carbon nanotube‐filled ethylene/vinylacetate copolymers: from in situ catalyzed polymerization to high‐performance electro‐conductive nanocomposites

Preparation and analysis of morphology, mechanical, and electrical properties of nanocomposites based on ethylene vinyl acetate (EVA) copolymer and commercial multiwalled carbon nanotubes (CNTs) was achieved. The used techniques for obtaining nanocomposites were the conventional melt‐mixing and the in situ ethylene polymerization/coating reaction, as catalyzed directly from CNT surface, with different polyethylene content (i.e. 55.0% and 66.6%). Nanocomposites were also prepared using crude CNTs. The incorporation in the molten state of such polyethylene surface‐coated CNTs, used as “masterbatch,” in EVA was demonstrated a good strategy for allowing the complete destructuring of the native bundle‐like aggregates, leading to the preparation of polymer nanocomposites with largely improved properties, even at very low nanofiller content. Copyright © 2011 John Wiley & Sons, Ltd.     

Mechanical and thermal properties of attapulgite clay reinforced polymethylmethacrylate nanocomposites

To investigate the dispersion and nanofillers' interaction of rod‐like silicates (attapulgite, ATT) in the polymethylmethacrylate (PMMA) matrix, a novel in situ modification of ATT by toluene‐2,4‐di‐isocyanate (TDI) using mechanical mixing was exploited, which resulted in homogeneous dispersion and rod‐like texture of ATT nanorods. As a consequence, organo‐modified ATT/PMMA nanocomposites were prepared, which provided prominent improvements in strength, toughness, and thermal stability. High grafting efficiency of TDI on ATT surface was confirmed by FTIR spectra and SEM observations. The uniform dispersion of in situ TDI modified ATT nanorods in the PMMA which was clearly visible in the TEM micrographs, influenced the mechanical and thermal properties of the nanocomposites. The fibrous nanoparticles significantly confined the segmental motion, causing a 13.20°C increase in the glass transition temperature of 2 wt% in situ TDI modified ATT/PMMA nanocomposites. But at higher loadings little or no differences were observed for the reinforcement benefits provided by the in situ TDI modified ATT clay. By comparison, pre‐treated ATT clay severely fractured during mechanical mixing and showed little reinforcement benefits. Copyright © 2010 John Wiley & Sons, Ltd.     

Dynamic mechanical behavior of acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) blends

The dynamic mechanical behavior of uncrosslinked (thermoplastic) and crosslinked (thermosetting) acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) (NBR/EVA) blends was studied with reference to the effect of blend ratio, crosslinking systems, frequency, and temperature. Different crosslinked systems were prepared using peroxide (DCP), sulfur, and mixed crosslink systems. The glass‐transition behavior of the blends was affected by the blend ratio, the nature of crosslinking, and frequency. sThe damping properties of the blends increased with NBR content. The variations in tan δ_max were in accordance with morphology changes in the blends. From tan δ values of peroxide‐cured NBR, EVA, and blends the crosslinking effect of DCP was more predominant in NBR. The morphology of the uncrosslinked blends was examined using scanning electron and optical microscopes. Cocontinuous morphology was observed between 40 and 60 wt % of NBR. The particle size distribution curve of the blends was also drawn. The Arrhenius relationship was used to calculate the activation energy for the glass transition of the blends, and it decreased with an increase in the NBR content. Various theoretical models were used to predict the modulus of the blends. From wide‐angle X‐ray scattering studies, the degree of crystallinity of the blends decreased with an increasing NBR content. The thermal behavior of the uncrosslinked and crosslinked systems of NBR/EVA blends was analyzed using a differential scanning calorimeter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1556–1570, 2002     

Interfacial interaction in EVA‐carbon nanotube and EVA‐clay nanocomposites

Proper filler‐matrix compatibility is a key factor in view of obtaining nanocomposites with well‐dispersed nanofillers displaying enhanced properties. In this respect, polymer‐filler interaction can be improved by a proper combination of matrix and nanofiller polarities. This is explored for matrices ranging from nonpolar high density poly(ethylene) to ethylene‐vinyl acetate (EVA) copolymers with varying vinyl acetate contents, in combination with several types of organoclay or carbon nanotubes. A novel in situ characterization methodology using modulated temperature differential scanning calorimetry is presented to evaluate the matrix‐filler interaction. During quasi‐isothermal crystallization of the matrix, an “excess” contribution is observed in the recorded heat capacity signal because of reversible melting and crystallization. Its magnitude considerably decreases upon addition of nanofiller in case of strong interfacial interaction, whereas the influence is moderate in case of a less interacting matrix‐filler combination. It is suggested that the “excess heat capacity” can be used to quantify the segmental mobility of polymer chains in the vicinity of the nanofiller. Hence it provides valuable information on the strength of interaction, governed by the physical and chemical nature of matrix and filler. Heating experiments subsequent to quasi‐isothermal crystallization point at a certain degree of molecular ordering, responsible for crystal nucleation in EVA copolymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1291–1302, 2007     

Extruder‐made TPO nanocomposites. I. Effect of maleated polypropylene and organoclay ratio on the morphology and mechanical properties

PP/PP‐g‐MA/MMT/EOR blend nanocomposites were prepared in a twin‐screw extruder at fixed 30 wt % elastomer and 0 to 7 wt % MMT content. Elastomer particle size and shape in the presence of MMT were evaluated at various PP‐g‐MA/organoclay masterbatch ratios of 0, 0.5, 1.0, and 1.5. The organoclay dispersion facilitated by maleated polypropylene serves to reduce the size of the elastomer dispersed phase particles and facilitates toughening of these blend nanocomposites. The rheological data analysis using modified Carreau‐Yasuda model showed maximum yield stress in extruder‐made nanocomposites compared with nanocomposites of reactor‐made TPO. Increasing either MMT content or the PP‐g‐MA/organoclay ratio can drive the elastomer particle size below the critical particle size below which toughness is dramatically increased. The ductile‐brittle transition shift toward lower MMT content as the PP‐g‐MA/organoclay ratio is increased. The D‐B transition temperature also decreased with increased MMT content and masterbatch ratio. Elastomer particle sizes below ～1.0 μm did not lead to further decrease in the D‐B transition temperature. The tensile modulus, yield strength, and elongation at yield improved with increasing MMT content and masterbatch ratio while elongation at break was reduced. The modified Mori‐Tanaka model showed better fit to experimental modulus when the effect of MMT and elastomer are considered individually. Overall, extruder‐made nanocomposites showed balanced properties of PP/PP‐g‐MA/MMT/EOR blend nanocomposites compared with nanocomposites of reactor‐made TPO. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Influence of organoclay dispersed state of poly(ethylene glycol‐co‐1,3/1,4‐cyclohexanedimethanol terephthalate)/organoclay nanocomposites on their characteristics

This work prepared poly(ethylene glycol‐co‐1,3/1,4‐cyclohexanedimethanol terephthalate) (PETG)/organoclay nanocomposites via a melt intercalation process and investigated the influences of organoclay aspect ratio and organoclay content on the dispersed state, mechanical, thermal, gas barrier, and heat recovery properties of PETG/organoclay nanocomposites. X‐ray diffraction (XRD) and transmission electron microscopic analyses showed that the organoclay dispersed in the polymer matrix with intercalation in the nanometer scale range. Differential scanning calorimetry (DSC) analysis demonstrated that all of the obtained nanocomposites were amorphous, indicating that the addition of organoclay did not affect the amorphous nature of PETG. The gas barrier properties of the nanocomposites improved with organoclay content and the properties were also affected by the organoclay aspect ratio. Water vapor and oxygen transmission rates (OTRs) of PETG/organoclay nanocomposites containing 3 phr Cloisite 15A, and 3 phr modified polymer grade Na‐montmorillonites (MPGN) were the lowest among the samples tested, and were 41.7 and 44.3%, respectively, of those of neat PETG. Similar organoclay content‐ and aspect ratio‐related effects were observed in the mechanical and heat recovery properties of the tested nanocomposites. Copyright © 2010 John Wiley & Sons, Ltd.     

Photocrosslinking and related properties of intumescent flame‐retardant LLDPE/EVA/IFR blends

The photoinitiated crosslinking of halogen‐free flame retarded linear low density polyethylene/poly(ethylene‐co‐vinyl acetate) blends (LLDPE/EVA) with the intumescent flame retardant (IFR) of phosphorous‐nitrogen compound (NP) in the presence of photoinitiator and crosslinker and their characterization of related properties have been investigated by gel determination, heat extension test, cone calorimeter test (CCT), thermogravimetric analysis (TGA), Fourier transfer infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), mechanical properties measurements, limiting oxygen index (LOI), UL‐94, and water resistance test. The data from the gel content and heat extension rate (HER) show that the LLDPE/EVA/IFR blends filled with NP are readily crosslinked to a gel content of above 75% and the HER values reach about 50% by UV‐irradiation of 5 sec under suitable amount of photoinitiator and crosslinker. The data obtained from the CCT and LOI indicate that photocrosslinking can considerably decrease the heat release rates (HRR) by 10–15%, prolongate the combustion time, and increase two LOI values for the LLDPE/EVA/NP blends UV irradiated for 5 sec. The results from TGA and the dynamic FTIR spectra give the evidence that the photocrosslinked LLDPE/EVA/NP samples show slower thermal degradation rate and higher thermo‐oxidative degradation temperature than the uncrosslinked LLDPE/EVA/NP samples. The morphological structures of charred residues observed by SEM give the positive evidence that the compact charred layers formed from the photocrosslinked LLDPE/EVA/NP samples play an important role in the enhancement of flame retardant and thermal properties. The data from the mechanical tests and water‐resistant measurements show that photocrosslinking can considerably improve the mechanical and water‐resistant properties of LLDPE/EVA/NP samples. Copyright © 2011 John Wiley & Sons, Ltd.     

Mechanical and anti‐stabbing properties of modified thermoplastic polymers impregnated multiaxial p‐aramid fabrics

New forms of hybrid multiaxial nanocomposites with enhanced mechanical and stab resisting properties are presented. This study is motivated by the lack of knowledge in the study of the multiaxial fabric nanocomposites with two modified thermoplastic matrices for antiballistic protection. Introduction of 5 wt.% silica nanoparticles in the composite of polyurethane/p‐aramid/poly (vinyl butyral) leads to significant improvement in mechanical properties, and the addition of silane as a coupling agents and glutaraldehyde as a crosslinking agents yielded maximal values of storage modulus, tensile modulus and anti‐stabbing properties for hybrid nanocomposites. Ballistic resistance testing and penetration depth of the hybrid nanocomposites were visualized using image analysis. Copyright © 2013 John Wiley & Sons, Ltd.     

Effect of matrix viscosity on the extent of exfoliation in EVA/organoclay nanocomposites

The influence of matrix viscosity and polarity on ethylene‐vinyl acetate copolymer (EVA) nanocomposites was studied. Five different EVA grades, with different melt flow indexes (MFIs) and/or vinyl acetate (VA) contents, were mixed with two montmorillonite (MMT) nanoclays: pristine and modified with a polar surfactant, producing 75/25 w/w% masterbatches which were subsequently diluted in the EVA matrix to obtain 5 wt% MMT nanocomposites. Although the same VA content, WAXS results, rheological measurements and TEM analysis showed that the lower the EVA viscosity, the greater the tendency to obtain exfoliated and well dispersed nanocomposites with the organically modified clay. On the other hand, the high viscosity EVA nanocomposites showed that the (001) organoclay diffraction peak was shifted to higher values of 2θ, suggesting lamellae collapsing. TGA and FTIR measurements were used to probe the thermal degradation of organoclay; furthermore, it was not possible to identify, by the techniques used, any reaction between the VA groups and hydroxyl surfactant groups. Thus, it was inferred that the organic surfactant was removed (or ejected) from the clay galleries as a consequence of huge shear tensions developed during processing of the masterbatches/nanocomposites with high viscosity EVA matrices. Copyright © 2009 John Wiley & Sons, Ltd.     

Dynamics of cyclodimerization and viscoelasticity of photo‐crosslinkable PVA

We investigated the interfacial properties of poly(vinyl alcohol) carrying UV‐crosslinkable pendant quaternized stilbazole (styrylpyridinium), PVA‐SbQ. The extent and dynamics of PVA‐SbQ cyclodimerization reactions and crosslinking induced by UV irradiation were monitored in situ and in real time by quartz crystal microgravimetry (QCM). Sensograms reflecting time‐dependent changes in density and viscoelasticity of crosslinking films followed a Boltzmann sigmoidal model, depending on precursor film composition and irradiation power. The shifts in QCM frequency and energy dissipation upon PVA‐SbQ cyclodimerization correlated with three photo‐crosslinking phases involving soft‐to‐rigid transitions, namely, induction (initiation), main crosslinking (interaction), and termination. PVA‐SbQ films crosslinked to different degree were used as protein carriers and a slower release profile was determined for the films that underwent more extensive crosslinking. Overall, this study demonstrates for the first time the dynamics of PVA‐SbQ crosslinking and its impact in system viscoelasticity and protein release. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 345–355     

Effect of different matrices and nanofillers on the rheological behavior of polymer‐clay nanocomposites

In this work, a comprehensive study of the rheological behavior under shear and isothermal and nonisothermal elongational flow of low density polyethylene (LDPE) and ethylene‐vinyl acetate copolymer (EVA) based nanocomposites was reported to evaluate their “filmability”, that is, the ability of these material to be processed for film forming applications. The influence of two different kinds of organoclay – namely Cloisite 15A and Cloisite 30B – and their concentration was evaluated. The presence of filler clearly affects the rheological behavior in oscillatory state of polyolefin‐based nanocomposites but the increase of complex viscosity and the shear thinning are not dramatic. A larger strain‐hardening effect in isothermal elongational flow is shown by the nanocomposites compared to that of the pure matrix, particularly for EVA based nanocomposites. The melt strength measured under nonisothermal elongational flow increases in the presence of the nanofiller, while the drawability is only slightly lower than that measured for the neat matrix. Moreover, the rheological behavior under nonisothermal elongational flow of EVA‐based nanocomposites is similar for both nanoclays used. Differently, LDPE‐based nanocomposites show a strong dependence on the type of organoclay. Finally, the mechanical properties of the materials were measured by tensile tests. They revealed that the presence of the filler provokes, in all the cases, an increase of the rigidity. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 344–355, 2010     

Effect of Organic Nano Carboncapsule Incorporated Modified Clay on Fire‐Retardancy of PMMA Nanocomposites

Here we investigate a new type of highly flame retardant poly(methyl methacrylate) (PMMA) nanocomposite by bulk polymerization of methyl methacrylate (MMA) in the presence of organic nano carboncapsule (OCNC/NCNC)‐incorporated modified montmorillonites (CL120, CL42). The morphology of the modified clay was confirmed by X‐ray diffraction (XRD), and Fourier transform infrared (FT‐IR) spectroscopy was used to identify the functional groups in the clay. The nano morphological characterization of the clay in the PMMA matrix was confirmed by XRD and transmission electron microscopy (TEM). The thermal and mechanical properties of the PMMA nanocomposites were investigated by thermogravimetry and dynamic mechanical analysis, respectively. PMMA containing organo nano carboncapsule‐doped CL42 modified cocoamphodipropionate (K2) (P‐O‐CL42) could achieve very high thermal stability compared to pristine PMMA. The 5% thermal decomposition temperature (T _5d) increased by 63.2°C. Storage modulus of PMMA nanocomposites measured by DMA analysis. An enhancement of storage modulus and significant reduction in the peak heat release (PHR) rate were observed in the almost all PMMA nanocomposites as compared to pristine PMMA. Moreover, these results suggest that PMMA nanocomposites can have potential applications in the building industry and the medical field.     

Nanospace preparation by crosslinking helical syndiotactic‐poly(methacrylic acid) in acetonitrile/water after stereocomplexation

Various molecular weights of isotactic (it‐)‐poly(methyl methacrylate) (PMMA) and syndiotactic (st‐)‐poly(methacrylic acid) (PMAA) were used to form an it‐PMMA/st‐PMAA (1/2) stereocomplex in acetonitrile/water as a suspension. The stereocomplex was tentatively crosslinked with 1,11‐diamino‐3‐6‐9‐trioxaundecane and water soluble carbodiimide at 10, 20, and 40 mol % concentrations versus MAA unit. The it‐PMMA was extracted from the crosslinked stereocomplex under alkaline conditions, and the successive re‐incorporation of the it‐PMMA was carried out. During the extraction and re‐incorporation processes, the FTIR/ATR spectra showed the absence and generation of a peak at 860 cm^?1, respectively, which was characteristic of this stereocomplex. The result of the XRD analysis also corresponded with the extraction and re‐incorporation behavior of it‐PMMA; peaks were observed at 2θ = 12 and 15°, d = 0.74 and 0.59 nm, respectively. This study showed that the nanospaces of helical st‐PMAA were available in acetonitrile/water in a suspended state using a crosslinking approach. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Tuning amphiphilicity/temperature‐induced self‐assembly and in‐situ disulfide crosslinking of reduction‐responsive block copolymers

New poly(ethylene oxide)‐based block copolymers (ssBCs) with a random copolymer block consisting of a reduction‐responsive disulfide‐labeled methacrylate (HMssEt) and a thermoresponsive di(ethylene glycol)‐containing methacrylate (MEO₂MA) units were synthesized. The ratio of HMssEt/MEO₂MA units in the random P(MEO₂MA‐co‐HMssEt) copolymer block enables the characteristics of well‐defined ssBCs to be amphiphilic or thermoresponsive and double hydrophilic. Their amphiphilicity or temperature‐induced self‐assembly results in nanoaggregates with hydrophobic cores having different densities of pendant disulfide linkages. The effect of disulfide crosslinking density on morphological variation of disulfide‐crosslinked nanogels is investigated. In response to reductive reactions, the partial cleavage of pendant disulfide linkages in the hydrophobic cores converts the physically associated aggregates to disulfide‐crosslinked nanogels. The occurrence of in‐situ disulfide crosslinks provides colloidal stability upon dilution. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2057–2067     

Transport properties of crosslinked acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) blends

The diffusion and transport of organic solvents through crosslinked nitrile rubber/poly(ethylene‐co‐vinyl acetate) (NBR/EVA) blends have been studied. The diffusion of cyclohexanone through these blends was studied with special reference to blend composition, crosslinking systems, fillers, filler loading, and temperature. At room temperature the mechanism of diffusion was found to be Fickian for cyclohexanone–NBR/EVA blend systems. However, a deviation from the Fickian mode of diffusion is observed at higher temperature. The transport coefficients, namely, intrinsic diffusion coefficient (D*), sorption coefficient (S), and permeation coefficient (P) increase with the increase in NBR content. The sorption data have been used to estimate the activation energies for permeation and diffusion. The van't Hoff relationship was used to determine the thermodynamic parameters. The affine and phantom models for chemical crosslinks were used to predict the nature of crosslinks. The experimental results were compared with the theoretical predictions. The influence of penetrants transport was studied using dichloromethane, chloroform, and carbon tetrachloride. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1815–1831, 1999     

Ultraviolet‐induced crosslinking of poly(butylene succinate) and its thermal property,dynamic mechanical property,and biodegradability

Crosslinking is an effective way to improve polymer properties. This paper focuses on ultraviolet‐induced crosslinking of poly(butylene succinate) (PBS) in the presence of a photoinitiator and a crosslinking agent at ambient temperature. The effects of the concentration of photoinitiator, the crosslinking agent content, and the irradiation time on the crosslink behavior were investigated. To obtain an appropriate gel fraction in different irradiation times, 3.0 wt% of photoinitiator and 10.0 wt% of crosslinking agent were proved to be the optimum choice. Furthermore, properties such as thermal properties, dynamic mechanical property, and enzymatic degradation of PBS before and after crosslinking were examined. Differential scanning calorimetry (DSC) analysis revealed that glass transition temperature (T_g) increased with increase in gel fraction, while melting temperature (T_m) and the degree of crystallinity decreased. This may be caused by the reduced molecular chain mobility and inhibited molecular motion for crystallization in crosslinked samples. The crosslinked polymer also showed improved thermal stability and dynamic mechanical property. In addition, the introduction of crosslinking retarded the enzymatic degradation rate of PBS, but it was still biodegradable. The improved properties of crosslinked PBS will extend the application of PBS. Copyright © 2009 John Wiley & Sons, Ltd.