The effect of gamma irradiation on mechanical, and thermal properties of recycling polyethylene terephthalate and low density polyethylene (R-PET/LDPE) blend compatibilized by ethylene vinyl acetate (EVA)

A study has been made on the compatibility of recycled polyethylene terephthalate (R-PET) and low density polyethylene (LDPE) blend in the presence of ethylene vinyl acetate (EVA) as a compatibilizing agent prepared by extrusion hot stretching process. EVA content in the blend as a compatibilizing agent was an enhancement effect on radiation crosslinking of R-PET/EVA/LDPE blends and the highest radiation crosslinking was obtained when the EVA content was reached at 10 % EVA when irradiated by gamma irradiation. Blends containing different (EVA) ratios were irradiated to different doses of gamma irradiation 25, 50 and 100 kGy. The effect of the compatibilizer and radiation on mechanical, thermal properties of R-PET together with LDPE and morphology has been investigated. It was found that gamma irradiation together with the presence of compatibilizing agent (EVA) has positive effect on the mechanical and thermal properties of R-PET/LDPE blend. The structural properties of R-PET/LDPE modified by gamma irradiation and EVA as compatibilizing agent was examined by SEM. Also, it was found that the optimum concentration of EVA and gamma irradiation dose was found to be 10 % EVA and 100 kGy, respectively.     

Characterization of electron beam irradiation blends based on metallocene ethylene‐1‐octene copolymer

Binary blends using metallocene ethylene‐1‐octene copolymer as matrix were prepared and subjected to electron beam (EB) irradiation (50, 100, and 200 kGy). Gel content and melt flow index values indicated that the blends were crosslinking. Fourier transform infrared‐ATR spectroscopy was used to study the crosslinking and oxidative degradation of the blends via tertiary carbon and carboxyl group formation, respectively. Thermal and mechanical properties were studied showing that the crystallinity of both matrix and dispersed phase decreased with irradiation dose, and that the thermoplastic elastomers with good mechanical properties may be obtained by EB irradiation. Chain branching and scission were also detected at all irradiation doses, although at the highest doses (200 kGy) a crosslinking reaction was the most predominantly observed effect. The successive self‐nucleation annealing technique was used to determine the EB irradiation effects on crystallization of some blends in which crosslinking and chain branching take place, modifying the chain's structure and therefore crystalline regions in the matrix and the dispersed phase. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2432–2440, 2007     

Photocrosslinking and related properties of intumescent flame‐retardant LLDPE/EVA/IFR blends

The photoinitiated crosslinking of halogen‐free flame retarded linear low density polyethylene/poly(ethylene‐co‐vinyl acetate) blends (LLDPE/EVA) with the intumescent flame retardant (IFR) of phosphorous‐nitrogen compound (NP) in the presence of photoinitiator and crosslinker and their characterization of related properties have been investigated by gel determination, heat extension test, cone calorimeter test (CCT), thermogravimetric analysis (TGA), Fourier transfer infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), mechanical properties measurements, limiting oxygen index (LOI), UL‐94, and water resistance test. The data from the gel content and heat extension rate (HER) show that the LLDPE/EVA/IFR blends filled with NP are readily crosslinked to a gel content of above 75% and the HER values reach about 50% by UV‐irradiation of 5 sec under suitable amount of photoinitiator and crosslinker. The data obtained from the CCT and LOI indicate that photocrosslinking can considerably decrease the heat release rates (HRR) by 10–15%, prolongate the combustion time, and increase two LOI values for the LLDPE/EVA/NP blends UV irradiated for 5 sec. The results from TGA and the dynamic FTIR spectra give the evidence that the photocrosslinked LLDPE/EVA/NP samples show slower thermal degradation rate and higher thermo‐oxidative degradation temperature than the uncrosslinked LLDPE/EVA/NP samples. The morphological structures of charred residues observed by SEM give the positive evidence that the compact charred layers formed from the photocrosslinked LLDPE/EVA/NP samples play an important role in the enhancement of flame retardant and thermal properties. The data from the mechanical tests and water‐resistant measurements show that photocrosslinking can considerably improve the mechanical and water‐resistant properties of LLDPE/EVA/NP samples. Copyright © 2011 John Wiley & Sons, Ltd.     

Properties of radiation‐modified blends of polyethylene with elastomers and liquid crystalline copolyester

The results are given on the effect of γ‐irradiation on properties of blends of high and low‐density polyethylene (HDPE, LDPE) with elastomers ‐ethylene/propylene/diene rubber (EPDM) and chlorinated polyethylene (CPE), and thermotropic liquid crystalline polymer (LCP). The morphological, thermal, mechanical properties (including thermosetting properties) and adhesion properties of blended composites were investigated. A special attention was paid to the applicability of the blends as thermosetting materials (TSM). The LCP used was a copolyester of poly(ethylene terephthalate) with p‐(hydroxybenzoic acid) in the ratio 40 : 60. It was found that addition of LCP essentially influenced the thermomechanical and adhesion properties of PE composites, irradiated up to the absorbed dose 150 kGy, as well as the dimensional stability of thermosetting products, made from polyethylene/elastomer mixtures. The results show that such ternary blends considerably improve the exploitation conditions of irradiated polyethylene and useful thermosetting materials can be obtained.     

Effect of electron beam irradiation on mechanical and thermal properties of waste polyamide copolymer blended with nitrile‐butadiene rubber

In the present study, the effect of electron beam irradiation on the morphological, thermal, and mechanical properties of waste polyamide copolymer (WPA‐66/6) blended with different contents of acrylonitrile butadiene rubber (NBR) were studied. The prepared blends were subjected to irradiation doses up to 150 kGy and the structural modifications were discussed; non‐irradiated blends were used as control. Mechanical properties, namely, tensile strength (TS), yield strength, elongation at break, and hardness, were followed up as functions of irradiation dose and degree of loading with rubber content. On the other hand, the influence of irradiation dose on the thermal parameters, melting temperature, heat of fusion, ΔH_m of the recycled PA copolymer, and its blend with NBR were also investigated. Copyright © 2009 John Wiley & Sons, Ltd.     

Characterization of irradiation-induced crosslink of epoxidised natural rubber/ethylene vinyl acetate (ENR-50/EVA) blend

The effect of irradiation on tensile, dynamic mechanical properties, thermal properties and morphology of ENR-50, EVA and ENR-50/EVA blend was investigated. All the samples were irradiated using a 3.0 MeV electron beam (EB) machine with doses ranging from 20 to 100 kGy. Results indicate that the gel fraction of ENR-50, EVA and ENR-50/EVA blend increases with irradiation dose. Concerning tensile properties, it can be seen that EB radiation increases the tensile strength of all the samples, increases the elongation at break of ENR-50 and ENR-50/EVA blend, reduces the elongation at break of EVA, increases M200 (modulus at 200% strain) of ENR-50 and EVA, while decreases M200 of the ENR-50/EVA blend. For dynamic mechanical studies, it was found that EB radiation increases the T_g of all the samples due to the effect of irradiation-induced crosslinking. The compatibility of ENR-50/EVA blend also found to be improving upon irradiation. In the case of thermal properties, it was detected that T_m, T_c and the degree of crystallinity of ENR-50/EVA blend increase with an increase in irradiation dose. This was due to the perfection in the crystal growth occurring upon radiation. Morphology changes play a major role in the changes of the properties of ENR-50/EVA blend. Finally, it can be concluded that ENR-50/EVA blend can be vulcanized by EB radiation.     

Electrically conductive,melt‐processed ternary blends of polyaniline/dodecylbenzene sulfonic acid,ethylene/vinyl acetate,and low‐density polyethylene

Although polyaniline (PANI) has high conductivity and relatively good environmental and thermal stability and is easily synthesized, the intractability of this intrinsically conducting polymer with a melting procedure prevents extensive applications. This work was designed to process PANI with a melting blend method with current thermoplastic polymers. PANI in an emeraldine base form was plasticized and doped with dodecylbenzene sulfonic acid (DBSA) to prepare a conductive complex (PANI–DBSA). PANI–DBSA, low‐density polyethylene (LDPE), and an ethylene/vinyl acetate copolymer (EVA) were blended in a twin‐rotor mixer. The blending procedure was monitored, including the changes in the temperature, torque moment, and work. As expected, the conductivity of ternary PANI–DBSA/LDPE/EVA was higher by one order of magnitude than that of binary PANI–DBSA/LDPE, and this was attributed to the PANI–DBSA phase being preferentially located in the EVA phase. An investigation of the morphology of the polymer blends with high‐resolution optical microscopy indicated that PANI–DBSA formed a conducting network at a high concentration of PANI–DBSA. The thermal and crystalline properties of the polymer blends were measured with differential scanning calorimetry. The mechanical properties were also measured. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3750–3758, 2004     

Photocrosslinking of EVA/inorganic filler blends and characteristics of related properties

The blends of EVA filled with talc, calcium carbonate, and glass ball (GB) have been photocrosslinked by UV irradiation in the presence of benzophenone (BP) as a photoinitiator and triallyl isocyanurate (TAIC) as a crosslinker. The various factors affecting the crosslinking process and the related properties have been studied by gel determination, heat extension test, mechanical and thermal aging test, UV spectroscopy, and scanning electron microscopy. The results show that the EVA/talc, EVA/CaCO₃, and EVA/GB samples of 1 mm thickness filled with 25 phr inorganic filler can be photocrosslinked to gel content of above 70 wt% by 5 sec UV‐irradiation under optimum conditions, which is sufficient for some applications of EVA blend materials. The crosslinking rate and final gel content level are in the order of EVA/GB > EVA/talc > EVA/CaCO₃. The data from mechanical and thermal aging tests give evidence that the photocrosslinked EVA/talc, EVA/CaCO₃, and EVA/GB samples are of much better tensile strength and thermal aging properties than those of the unphotocrosslinked ones. Copyright © 2009 John Wiley & Sons, Ltd.     

Simultaneous Enhancement of Mechanical and Dynamic Mechanical Properties of Natural Rubber/Recycled Ethylene-Propylene-Diene Rubber Blends by Electron Beam Irradiation

Mechanical and dynamic mechanical properties of natural rubber/recycled ethylene-propylene-diene rubber (NR/R-EPDM) blends were simultanoeusly enhanced by electron beam (EB) irradiation. The cross-linking promoter, trimethylolpropane triacrylate (TMPTA), was also introduced into the blends to induce the cross-linking. By applying EB irradiation, the tensile modulus, hardness, swelling, cross-link density, and storage modulus increased with increase in the irradiation dose; an irradiation dose of 50 kGy was efficient to gain optimum tensile strength. The formation of irradiation-induced cross-links after EB irradiation is a major concern for the enhancement of mechanical, swelling resistance, and dynamic mechanical properties of the blends.     

Synergistic effect of combination of Irganox 1010 and zinc stearate on thermal stabilization of electron beam irradiated HDPE/EVA both in hot water and oven

Thermo-oxidative stability of HDPE/EVA blends can be considerably increased by combination of a high-molecular weight phenolic antioxidant and zinc stearate. In this work, the post-irradiation thermal stability of HDPE/EVA blends has been studied. High-density polyethylene and its blends with ethylene-vinylacetate copolymer in both pure form and mixed with Irganox 1010 and zinc stearate were exposed to electron beam radiation at doses between 80 and 150 kGy, at room temperature, in air. In order to evaluate the thermal stability of the samples, post-irradiation heat treatments were done in both hot water bath at 95 °C and in an oven at 140 °C. The mechanical properties and changes in the chemical structure were determined during thermal aging in hot water and oven. The gel content was enhanced by increasing EVA concentration in all applied doses. The stabilized blends have lower gel content than the unstabilized samples. From the results of heat aging treatments it was observed that the thermal stability of the unstabilized blend samples was lower than HDPE. Thermal stability of the samples has been improved by incorporation of Irganox 1010 and zinc stearate. Formation of hydroxyl group was insignificant for stabilized samples during heat aging in both conditions. Also, the changes in the value of oxidation induction time (OIT) for the stabilized samples were negligible after prolonged immersion in hot water.     

Improvements of physical and mechanical properties of electron beam irradiation—crosslinked EVA foams

In this work, ethylene–vinyl acetate (EVA) copolymer foams were prepared and crosslinked by using high‐energy electron beam (e‐beam) radiation (10 MeV). The effect of parameters such as irradiation dose, the contents of foaming agent, radiation activator, and radiation sensitizer on improvement of physical and mechanical properties of the EVA foamed samples were investigated. The foams were obtained through a four‐step process of melt mixing, forming, crosslinking, and foaming. During the melt mixing process EVA was compounded with different amounts of azodicarbonamide (ADCA) as a blowing agent, zinc oxide (ZnO) as a radiation activator, and trimethylol propane‐trimethacrylate (TMPTMA) as a radiation sensitizer. The samples were compression molded into flat sheets at low temperature (110°C) and were then radiation‐crosslinked by 20–80 kGy e‐beam. Finally, the crosslinked samples were converted to foams by a high temperature (210°C) compression molding process. The foamed samples were analyzed in terms of gel content, density, compression molding set, tensile properties, and micro‐structural features. It was found that an increase in absorbed radiation dosage increases crosslink density, elasticity, percentage recovery, tensile strength, and compression properties of the EVA foams. Due to the increased recovery the percentage of compression set was reduced. Similarly increasing the TMPTMA content in the formulation increased the crosslink density and the resulting mechanical properties. Contrary to these findings, addition of ADCA led to the formation of extra gases which in turn reduced the crosslink density, and resulted in the deterioration of the mechanical properties and hence an increase in the compression set. However, addition of ZnO and TMPTMA led to the formation of smaller and more uniform cell size with improved mechanical properties. Copyright © 2008 John Wiley & Sons, Ltd.     

Effects of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] on the charge distributions of low‐density polyethylene/polystyrene blends

The effect of the triblock copolymer poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) on the formation of the space charge of immiscible low‐density polyethylene (LDPE)/polystyrene (PS) blends was investigated. Blends of 70/30 (wt %) LDPE/PS were prepared through melt blending in an internal mixer at a blend temperature of 220 °C. The amount of charge that accumulated in the 70% LDPE/30% PS blends decreased when the SEBS content increased up to 10 wt %. For compatibilized and uncompatibilized blends, no significant change in the degree of crystallinity of LDPE in the blends was observed, and so the effect of crystallization on the space charge distribution could be excluded. Morphological observations showed that the addition of SEBS resulted in a domain size reduction of the dispersed PS phase and better interfacial adhesion between the LDPE and PS phases. The location of SEBS at a domain interface enabled charges to migrate from one phase to the other via the domain interface and, therefore, resulted in a significant decrease in the amount of space charge for the LDPE/PS blends with SEBS. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2813–2820, 2004     

Mechanical properties and thermal analysis of low‐density polyethylene + polypropylene blends with dialkyl peroxide

Polypropylene + low density polyethylene (PP + LDPE) blends involving 0, 25, 50, 75 and 100 wt% of PP with dialkyl peroxide (DAP) were prepared by melt blending in a single‐screw extruder. The effects of adding dialkyl peroxide on mechanical and thermal properties of PP + LDPE blends have been studied. It was found that at lower concentrations of peroxide (e.g., 0–0.08 wt% of dialkyl peroxide) LDPE component is cross‐linked and Polypropylene (PP) is degraded in all compositions of PP + LDPE blends. Mechanical properties (Tensile strength at break, at yield and elongation at break), Melt flow index (MFI), hardness, Scanning Electron Microscope (SEM) and thermal analyses (DSC) of these blends were examined. Because of serious degradation or cross‐linking the mechanical properties and the crystallinty (%) of those products were decreased as a result of increasing peroxide content. Copyright © 2009 John Wiley & Sons, Ltd.     

Mechanical hysteresis,interface and filler–filler structural breakdowns in ethylene vinyl acetate organoclay composites internally lubricated via radiolytically degraded PTFE microparticles

Inclusion of two or more distinct fillers (hybrid fillers) in a matrix is envisaged to entail synergetic advantages. This study reports synthesis and property evaluation of a novel hybrid filler‐based polymer composite containing two types of fillers with distinct attributes namely mechanical reinforcement and internal lubrication. Poly(tetrafluoroethylene) micro‐particles (PTFEMP) were synthesized via radiolytic‐mechanical degradation and used as an internal lubricant for organoclay (OC) reinforced ethylene vinyl acetate (EVA) matrix. Mechanical hysteresis, nonlinear and linear small amplitude oscillatory shear rheology, morphology, small angle X‐ray scattering (SAXS), dynamic coefficient of friction (DCoF), surface wetting and thermoxidative stability of binary and ternary composites were investigated. In EVA/OC composites, PTFEMP acted as an internal lubricant and reduced DCoF in a volume fraction‐dependent fashion. OC and PTFEMP both increased the mechanical hysteresis of EVA; though the magnitude of hysteresis was much less in PTFEMP. Intriguingly, PTFEMP reduced mechanical hysteresis of EVA/OC composites that is work done during loading and unloading stress–strain cycles was considerably reduced with the inclusion of PTFEMP in EVA/OC composites. SAXS results revealed mass fractals and the presence of an interfacial layer in EVA/OC composites but not in EVA/PTFEMP composites. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 509–519     

Electron beam crosslinking of poly(ethylene-co-vinyl acetate)/clay nanocomposites

Effect of electron beam irradiation on the thermal and mechanical properties of poly(ethylene-co-vinyl acetate) (EVA)/clay nanocomposites prepared by melt blending method has been investigated. The hot set test results show that elongation at high temperature under static load decreased with the increase of irradiation dose. The tensile modulus increased continuously with increasing dose. While the tensile strength increased up to 100 kGy, it decreased with further increase in dose. The elongation at break decreased continuously with increasing dose. Thermogravimetric analysis showed that thermal stability of the EVA/clay nanocomposites improved with increasing dose. The improvement in the mechanical and thermal properties is attributed to the formation of radiation-induced crosslinking as evidenced by the gel content results.     

Dynamic mechanical behavior of acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) blends

The dynamic mechanical behavior of uncrosslinked (thermoplastic) and crosslinked (thermosetting) acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) (NBR/EVA) blends was studied with reference to the effect of blend ratio, crosslinking systems, frequency, and temperature. Different crosslinked systems were prepared using peroxide (DCP), sulfur, and mixed crosslink systems. The glass‐transition behavior of the blends was affected by the blend ratio, the nature of crosslinking, and frequency. sThe damping properties of the blends increased with NBR content. The variations in tan δ_max were in accordance with morphology changes in the blends. From tan δ values of peroxide‐cured NBR, EVA, and blends the crosslinking effect of DCP was more predominant in NBR. The morphology of the uncrosslinked blends was examined using scanning electron and optical microscopes. Cocontinuous morphology was observed between 40 and 60 wt % of NBR. The particle size distribution curve of the blends was also drawn. The Arrhenius relationship was used to calculate the activation energy for the glass transition of the blends, and it decreased with an increase in the NBR content. Various theoretical models were used to predict the modulus of the blends. From wide‐angle X‐ray scattering studies, the degree of crystallinity of the blends decreased with an increasing NBR content. The thermal behavior of the uncrosslinked and crosslinked systems of NBR/EVA blends was analyzed using a differential scanning calorimeter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1556–1570, 2002     

Shape memory behavior of carbon nanotube‐reinforced trans‐1,4‐polyisoprene and low‐density polyethylene composites

Shape memory composites of trans‐1,4‐polyisoprene (TPI) and low‐density polyethylene (LDPE) with easily achievable transition temperatures were prepared by a simple physical blending method. Carbon nanotubes (CNTs) were introduced to improve the mechanical properties of the TPI/LDPE composites. The mechanical, cure, thermal, and shape memory properties of the TPI/LDPE/CNTs composites were investigated in this study. In these composites, the cross‐linked network generated in both the TPI and LDPE portions acted as a fixed domain, while the crystalline regions of the TPI and LDPE portions acted as a domain of reversible shape memory behavior. We found that CNTs acted as not only reinforced fillers but also nucleation agents, which improved the crystalline degree of the TPI and LDPE portions of the composites. Compared with the properties at the other CNT doses, the mechanical properties of the TPI/LDPE composites when the CNT dose was 1 phr were improved significantly, showing excellent shape memory properties (R_f = 97.85%, R_r = 95.70%).     

Effect of Electron Beam Irradiation and Ethylene Vinyl Acetate Copolymer on the Properties of NBR/HDPE Blends

The mechanical and physical properties of blends based essentially on nitrile butadiene rubber (NBR) and different ratios of high density polyethylene (HDPE) up to 25 parts per hundred part of rubber (phr) before and after electron beam irradiation were investigated. The values of tensile strength (TS), tensile modulus at 50% elongation (M₅₀), hardness and gel fraction % (GF%) of NBR/HDPE blends were increased with both irradiation dose and by increasing the content of HDPE in the blends. On the other hand, the values of elongation at break (E _b ) were decreased with both irradiation dose and the content of HDPE in the blends. By loading NBR/HDPE (100/25) blend with ethylene vinyl acetate (EVA) copolymer the mechanical and physico-chemical properties were improved. Moreover, the degree of improvement is proportional to the loading content of EVA.     

Mechanical properties,surface chemistry,and barrier characteristics of electron beam irradiated‐annealed LDPE/PA6/LDPE multi‐layer films at N2

The effects of electron beam irradiation in the nitrogen environment, on chain scission, crosslinking, crystallinity, mechanical performance, and barrier properties of LDPE/PA6/LDPE multi‐layer films were studied. The evaluation of radiation‐induced crosslinking effect by the gel content measurement and Charlesby–Pinner plot suggested more of crosslinking over chain scission, in all the layers, which was more pronounced in polyethylene phase. The FTIR analysis results showed good agreement with those observed by the gel content measurements. It is believed that the crosslinking reaction had occurred through the C? N bonds in polyamide‐6, and vinyl group in polyethylene layers. The evaluation of radiation effect on the crystallinity and crosslinking of films by FTIR technique showed that by increasing the applied doses, the crystallinity in all the layers was decreased and the crosslinking was increased. The differential scanning calorimetry of irradiated samples revealed that due to the crosslinking reaction, the crystallinity was decreased by the applied dose. The tensile strength of the films was increased and the percent elongation at break was decreased, by increasing the applied doses. This study was also indicated that the radiation‐induced crosslinking effect on the tensile properties was dominantly observed up to 50 kGy. The surface free energy analysis of the films using the contact angle measurement and geometric mean equation indicated that the surface polarity was decreased by increasing the absorbed doses. It was found that due to the decline in the surface polarity and the simultaneously formation of crosslinked network in these films, both water vapor transmission rate and oxygen permeability were significantly decreased. Copyright © 2009 John Wiley & Sons, Ltd.     

Enhancing crystallization behavior for optimized performances of poly(TMC‐b‐(LLA‐ran‐GA)) by PDLA/PLLA stereocomplex crystallization

The blends of poly(1,3‐trimethylene carbonate‐b‐(l ‐lactide‐ran‐glycolide)) (PTLG) with poly(d ‐lactide) (PDLA) were prepared via solution‐casting method using CH₂Cl₂ as solvent. The poly(l ‐lactide) (PLLA) segments of PTLG with PDLA chain constructed as stereocomplex structures and growth stereocomplex crystals of PLA (sc‐PLA). The effects of sc‐PLA crystals on thermal behavior, mechanical properties, thermal decomposition of the PTLG/PDLA blends were investigated, respectively. The differential scanning calorimetry (DSC) and wide‐angle X‐ray diffraction (WAXD) results showed that the total crystallinity of the PTLG/PDLA blends was increased with the PDLA content increasing. Heterogeneous nucleation of sc‐PLA crystals induced crystallization of the PLLA segments in PTLG. The crystallization temperature of samples shifted to 107.5°C for the PTLG/PDLA‐20 blends compared with that of the PTLG matrix, and decreased the half‐time of crystallization. The mechanical measurement results indicated that the tensile strength of the PTLG/PDLA blends was improved from 21.1 MPa of the PTLG matrix to 39.5 MPa of PTLG/PDLA‐20 blends. The results of kinetics of thermal decomposition of the PTLG/PDLA blends by TGA showed that the apparent activation energy of the PTLG/PDLA blends was increased from 59.1 to 72.1 kJ/mol with the increasing of the PDLA content from 3 wt% to 20 wt%, which indicated the enhancement of thermal stability of the PTLG/PDLA blends by addition of PDLA. Furthermore, the biocompatibility of the PTLG/PDLA blends cultured with human adipose‐derived stem cells was evaluated by CCK‐8 and live/dead staining. The experiment results proved the PTLG/PDLA blends were a kind of biomaterial with excellent physical performances with very low cytotoxicity.