Porous-conductive chitosan scaffolds for tissue engineering, 1. Preparation and characterization

Novel porous-conductive chitosan scaffolds were fabricated by incorporating conductive polypyrrole (PPy) particles into a chitosan matrix and employing a phase separation technique to build pores inside the scaffolds. Conductive polypyrrole particles were prepared with a microemulsion method using FeCl3 as a dopant. The preparation conditions were optimized to obtain scaffolds with controlled pore size and porosity. The conductivity of the scaffolds was investigated using a standard four-point probe technique. It was found that several kinds of scaffolds showed a conductivity close to 10(-3) S.cm(-1) with a low polypyrrole loading of around 2 wt.-%. The main mechanical properties, such as tensile strength, breaking elongation and Young's modulus of the scaffolds, were examined both in the dry and in the hydrated states. The results indicated that a few different kinds of scaffolds exhibited the desired mechanical strength for some tissue engineering applications. The miscibility of polypyrrole and chitosan was also evaluated using a dynamic mechanical method. The presence of significant phase separation was detected in non-porous PPy/chitosan scaffolds but enhanced miscibility in porous PPy/chitosan scaffolds was observed.     

Surface characterization of TEMPO‐oxidized bacterial cellulose

In this study, we focused on the surface character of bacterial cellulose (BC) before and after oxidation mediated by 2,2,6,6‐tetramethylpiperidine‐1‐oxyl (TEMPO).Solid‐state ¹³C NMR, XPS, SEM, contact angle and surface free energy analyses were performed to investigate the effects of various parameters (reaction time and oxidant and catalyst concentrations) on the surface composition, morphology and polarity of the BC. The results provided by the combined use of these techniques showed that hydrogen bonds were disrupted on the BC surface after carboxylation occurred; therefore, the surface of oxidized BC was rougher than that of the original BC, and the surface free energy, especially the polar components, increased after oxidation. Copyright © 2013 John Wiley & Sons, Ltd.     

Homogeneous organic/inorganic hybrid scaffolds with high osteoinductive activity for bone tissue engineering

Composite scaffolds of polymers/β-tricalcium phosphate (TCP) have been widely used for bone regeneration due to the combination of osteoinductivity of TCP and mechanical properties of the polymers. However, the difference in surface properties of the two material causes composite has poor uniformity and weak two-phase interaction, resulting in poor TCP release and weak new bone-forming ability. In this research, a TCP sol was developed to replace traditional TCP nanoparticles for the preparation of homogeneous polycaprolactone (PCL)/TCP sol nanofibrous scaffolds. It was found that compared with TCP nanoparticles, TCP sol homogeneously distributed in PCL nanofibers, and greatly improved the hydrophilicity, biodegradability, and mechanical properties of the scaffolds. It is also confirmed that loading TCP sol promoted the formation of bone-like apatite on the surface of the scaffolds. Biological experiments showed that all scaffolds supported rat bone marrow mesenchymal stem cells (rBMSCs) proliferation, especially scaffolds loaded with TCP sol. The increase in alkaline phosphatase activity and collagen production, enhanced calcium deposition, and up-regulation of osteocalcin expression demonstrated that the loading TCP sol expanded an advantage of scaffolds in promoting rBMSCs osteogenic differentiation, suggesting it dramatically improved the osteoinductive activity of PCL/TCP hybrid system and had a great potential application in bone regeneration.     

Morphology and characterization of 3D micro-porous structured chitosan scaffolds for tissue engineering

This research studies the morphology and characterization of three-dimensional (3D) micro-porous structures produced from biodegradable chitosan for use as scaffolds for cells culture. The chitosan 3D micro-porous structures were produced by a simple liquid hardening method, which includes the processes of foaming by mechanical stirring without any chemical foaming agent added, and hardening by NaOH cross linking. The pore size and porosity were controlled with mechanical stirring strength. This study includes the morphology of chitosan scaffolds, the characterization of mechanical properties, water absorption properties and in vitro enzymatic degradation of the 3D micro-porous structures. The results show that chitosan 3D micro-porous structures were successfully produced. Better formation samples were obtained when chitosan concentration is at 1–3%, and concentration of NaOH is at 5%. Faster stirring rate would produce samples of smaller pore diameter, but when rotation speed reaches 4000 rpm and higher the changes in pore size is minimal. Water absorption would reduce along with the decrease of chitosan scaffolds’ pore diameter. From stress–strain analysis, chitosan scaffolds’ mechanical properties are improved when it has smaller pore diameter. From in vitro enzymatic degradation results, it shows that the disintegration rate of chitosan scaffolds would increase along with the processing time increase, but approaching equilibrium when the disintegration rate reaches about 20%.     

Preparation and characterization of hybrid cationic hydroxyethyl cellulose/sodium alginate polyelectrolyte antimicrobial films

This study aimed to develop polyelectrolyte‐structured antimicrobial food packaging materials that do not contain any antimicrobial agents. Cationic hydroxyethyl cellulose was synthesized and characterized by Fourier‐transform infrared, ¹H NMR, and ¹³C NMR spectroscopy. Its nitrogen content was determined by Kjeldahl method. Polyelectrolyte‐structured antimicrobial food packaging materials were prepared using hydroxyethyl cellulose, cationic hydroxyethyl cellulose, and sodium alginate. Antimicrobial activity of materials was defined by inhibition zone method (disc diffusion method). Thermal stability of samples was evaluated by thermal gravimetric analysis and differential scanning calorimetry. Surface morphology of samples was investigated by SEM. The obtained results prove that produced food packaging materials have good thermal and antimicrobial properties, and they can be used as food packaging material in many industries.     

Preparation and mechanical behavior of PLGA/nano-BCP composite scaffolds during in-vitro degradation for bone tissue engineering

In this paper, the yield strength and elastic modulus of Poly (lactide-co-glycolide) (PLGA) and PLGA/nano-biphasic calcium phosphate (nBCP) composite scaffolds, before and during in-vitro degradation, have been evaluated. Composite scaffolds were made by using PLGA matrix and 10-50 wt.% nBCP powder as the reinforcement material. All scaffolds, with more than 89% porosity, were fabricated by thermally-induced phase separation (TIPS). During in-vitro degradation (0-8 weeks), the PLGA/nBCP scaffolds showed both more weight loss and better mechanical properties as compared to neat PLGA scaffolds. The PLGA/nBCP scaffolds with 30 wt.% nBCP illustrated the highest value of yield strength among the composite scaffolds, before and after degradation, until 6 weeks. After 8 weeks, the yield strength values were very poor and close to each other. The values of elastic modulus for all samples were less than the half of their initial values after 6 weeks. However, after 8 weeks, the elastic moduli of all samples reduced to negligible values.     

HPMC crosslinked chitosan/hydroxyapatite scaffolds containing Lemongrass oil for potential bone tissue engineering applications

The chitosan (CS), hydroxypropyl methyl cellulose (HPMC), hydroxyapatite (HAp and Lemon grass oil (LGO) based scaffolds was prepared by freeze gelation method. The composite formation was confirmed by FTIR (Fourier-transform infrared spectroscopy) analysis and surface morphology was evaluated by SEM (Scanning Electron Microscopy) analysis. The mechanical strength, biodegradation, swelling, porosity and antibacterial activity were evaluated on the basis of LGO contents. The scaffold structure was porous and the mechanical strength was enhanced as a function of LGO contents. The scaffold properties analysis revealed the biodegradation nature and swelling behavior of CS-HPMC-HAp-LGO was also affected significantly as a function of LGO contents. The cytotoxicity of CS-HPMC-HAp-LGO was studied against MC3T3-E1 cells and based on cell viability, no toxic sign was observed. The antimicrobial activity was evaluated against S. aureus and CS-HPMC-HAp-LGO scaffolds showed promising activity, which was varied as a function of LGO contents. The findings revealed that the CS-HPMC-HAp-LGO are biocompatible and have potential for bone tissue engineering.     

Direct sulfation of bacterial cellulose with a ClSO3H/DMF complex and structure characterization of the sulfates

Bacterial cellulose (BC) is a form of cellulose synthesized by microorganisms, which has unique structure properties and differs from plant cellulose. Up to now, chemical modification of BC has not been studied widely. This paper aims to prepare sodium bacterial cellulose sulfate (SBS) in N,N‐dimethylformamide (DMF) with a ClSO₃H/DMF complex as the sulfating agent. SBSs with diverse degree of sulfation (DS, 0.04–0.86) were synthesized. The system could change from heterogeneous to homogeneous during the sulfation. Regarding to the DS, the optimal ClSO₃H amount and reaction time were 6 mol/mol anhydroglucose unit and 4 h, respectively. DS increased a little when increasing the temperature, while the yield decreased significantly. SBSs with DS > 0.24 were soluble in deionized water. Carbon nuclear magnetic resonance spectroscopy revealed that the sulfation prefers to take place in the order of C‐6 > C‐2 > C‐3. The X‐ray diffraction profiles indicated that the crystalline structure of BC was destroyed during sulfation. BC has better reactivity than microcrystalline cellulose in both sulfation and depolymerization processes. SBS is a potential biomaterial. However, BC depolymerized obviously in present sulfation, which forbids application of SBS in material. Moisture of the reaction mixture should be removed as completely as possible to guarantee efficient sulfation and decrease depolymerization. Copyright © 2013 John Wiley & Sons, Ltd.     

In vitro evaluation of cellulose acetate hemodialyzer immobilized with heparin

In this study, heparin was immobilized onto cellulose acetate hollow fibers to improve the anticoagulation performance during hemodialysis. In vitro evaluation was carried out using mini‐hemodialyzer circulating with fresh porcine whole blood to simulate kidney therapy. The dialysis performance and hemocompatibility were estimated. The results showed that heparinized hemodialyzer could be used through out the whole dialysis time (4 hr) without injecting additional heparin to prevent coagulation in the dialysis system. In addition, the hemocompatibility was evaluated by measuring activated partial thromboplastin time (APTT), prothrombin time (PT), and fibrinogen time (FT). The complete blood count (CBC) including red blood cell (RBC), hemoglobin (Hgb), hematocrit (Hct), white blood cell (WBC), and platelet were determined. The results showed that heparinization could keep the CBC stable during dialysis, whereas unmodified cellulose acetate hemodialyzer would cause a decrease in RBC unless heparin was injected during dialysis. Heparinized hemodialyzer showed longer APTT, PT, and FT than unmodified hemodialyzer. Heparinized hemodialyzer also showed slightly higher clearance than unmodified hemodialyzer. These results indicated that the dialysis performance and hemocompatibility of cellulose acetate hemodialyzer could be improved by the immobilization of heparin. Copyright © 2006 John Wiley & Sons, Ltd.     

Magnesium-zinc-graphene oxide nanocomposite scaffolds for bone tissue engineering

The aim of this study was to fabricate and evaluate magnesium-zinc-graphene oxide nanocomposite scaffolds for bone tissue engineering. For this reason, Mg-6Zn, Mg-6Zn-1GO, and Mg-6Zn-2GO scaffolds were fabricated by the powder metallurgy method. The porosity level and also the pore size of the scaffolds were evaluated by SEM which varied from 40 to 46% and 200 to 500 μm, respectively. The chemical composition and microstructure of the scaffolds were characterized by XRD and SEM equipped with EDS; the presence of Mg, Zn, C, and O elements in the structure of the scaffolds was shown. Also, the elemental map confirmed the existence of magnesium, zinc, carbon, and oxygen in the structure of the scaffold. The mechanical properties of the scaffolds were investigated by the compression test; the results showed that by the addition of graphene oxide to the structure, the compressive strength of the samples increased from 5 to 8 MPa. Electrochemical corrosion polarization tests were conducted to evaluate the corrosion resistance of the samples immersed in simulated body fluid (SBF). Furthermore, the biodegradability of the scaffolds was determined by immersion of the samples in phosphate-buffered saline (PBS). The results demonstrated that the polarization resistance value and the corrosion rate for different formulations including Mg-6Zn, Mg-6Zn-1GO, and Mg-6Zn-2GO were 41.58, 35.48, and 55.40 Ω.cm² followed by 10.60, 14.83, and 9.06 mm.year^?1, respectively. Based on the results, the Mg-6Zn-2GO formulation presented the best corrosion resistance among the samples were investigated, which confirmed the results of the immersion test. Moreover, the MTT assay proved that the extract of Mg-6Zn-2GO scaffolds was not cytotoxic in contact with L-929 cells which validated the studied scaffolds for bone tissue applications.     

Synthesis and characterization of hydroxypropyl cellulose from bacterial cellulose

Bacterial cellulose produced by Acetobacter xylinum has been reacted with propyleneoxide to synthesize hydroxypropyl cellulose(HPC) under different reaction conditions while diluted by toluene. The effects of mass ratio of bacterial cellulose to propyleneoxide, dilutability of toluene, reaction temperature(T) and time(t) were investigated by series of experiments. The degree of substitution(DS), hydroxypropyl content(A) and yield(η) were compared. The optimized product exhibited cold-water solubility and hot-water gelatinization in aqueous medium. Further study was carried out with FTIR, TGA, XRD, SEM and 13C-NMR for characterization. The water/air contact angle measurement reveals that it is a good hydrophobic material with good mechanical properties.     

Fabrication and enhanced mechanical properties of porous PLA/PEG copolymer reinforced with bacterial cellulose nanofibers for soft tissue engineering applications

A new class of polylactic acid (PLA)/polyethylene glycol (PEG) copolymer reinforced with bacterial cellulose nanofibers (BC) was prepared using a solvent casting and particulate leaching methods. Four weight fractions of BC (1, 2.5, 5, and 10 wt%) were incorporated into copolymer via silane coupling agent. Mechanical properties were evaluated using response surface method (RSM) to optimize the impact of pore size, porosity, and BC contents. Compressive strength obtained for PLA/PEG-5 BC wt% was 9.8 MPa, which significantly dropped after developing a porous structure to 4.9 MPa. Nielson model was applied to investigate the BC stress concentration on the PLA/PEG. Likewise, krenche and Hapli-Tasi model were employed to investigate the BC nanofiber reinforcement and BC orientation into PLA/PEG chains. The optimal parameters of the experiment results found to be 5 wt% for BC, 230 μm for pore size, and 80% for porosity. Scanning electron microscopy (SEM) micrograph indicates that uniform pore size and regular pore shape were achieved after an addition of BC-5% into PLA/PEG. The weight loss of copolymer-BC with scaffolds enhanced to the double values, compared with PLA/PEG-BC % without scaffolds. Differential Scanning Calorimetric (DSC) results revealed that the BC nanofiber improved glass transition temperature (T_g) 57 °C, melting temperature (T_m) 171 °C, and crystallinity (χ %) 43% of PLA/PEG reinforced-BC-5%.     

Fabrication of graphene‐silver/polyurethane nanofibrous scaffolds for cardiac tissue engineering

The graphene‐based nanocomposites are considered as great candidates for enhancing electrical and mechanical properties of nonconductive scaffolds in cardiac tissue engineering. In this study, reduced graphene oxide‐silver (rGO‐Ag) nanocomposites (1 and 2 wt%) were synthesized and incorporated into polyurethane (PU) nanofibers via electrospinning technique. Next, the human cardiac progenitor cells (hCPCs) were seed on these scaffolds for in vitro studies. The rGO‐Ag nanocomposites were studied by X‐ray diffraction (XRD), Raman spectroscopy, and transmission electron microscope (TEM). After incorporation of rGO‐Ag into PU nanofibers, the related characterizations were carried out including scanning electron microscope (SEM), TEM, water contact angle, and mechanical properties. Furthermore, PU and PU/nanocomposites scaffolds were used for in vitro studies, wherein hCPCs showed good cytocompatibility via 3‐(4, 5‐dimethylthiazol‐2‐yl)‐2,5‐diphenyl tetrazolium bromide (MTT) assay and considerable attachment on the scaffold using SEM studies. Real‐time polymerase chain reaction (PCR) and immunostaining studies confirmed the upregulation of cardiac specific genes including GATA‐4, T‐box 18 (TBX 18), cardiac troponin T (cTnT), and alpha‐myosin heavy chain (α‐MHC) in the PU/rGO‐Ag scaffolds in comparison with neat PU ones. Therefore, these nanofibrous rGO‐Ag–reinforced PU scaffolds can be considered as suitable candidates in cardiac tissue engineering.     

Initiator-free photocrosslinking of electrospun biodegradable polyester fiber based tubular scaffolds and their cell affinity for vascular tissue engineering

<正>Random copolyester of poly(ε-caprolactone-co-L-lactide)(PCLA) with a 50:50 feeding molar ratio was synthesized via the ring-opening polymerization and functionalized by the end-capping reaction with acryloyl chloride.The resulting acrylated PCLA was then fabricated into small diameter tubular scaffolds by electrospinning technique and the formed scaffolds were followed by photocrosslinking under UV irradiation in the absence of photoinitiator.The mechanical strengths including tensile,suture retention and burst pressure were greatly enhanced after the photocrosslinking.The in vitro degradation data clearly revealed that the mechanical properties of the crosslinked scaffolds still remained after one month degradation in PBS solution,while those of the non-crosslinked ones lost heavily.The cytotoxicity assay on the mouse fibroblast L929 cells was conducted via MTT measurement.Furthermore,the observation on endothelial and fibroblast cell adhesion and proliferation was also made by using scanning electron microscopy(SEM).The initiator-free photocrosslinked tubular scaffolds show the potential to be used in vascular tissue engineering.     

Insulin immobilized PCL‐cellulose acetate micro‐nanostructured fibrous scaffolds for tendon tissue engineering

Use of growth factors as biochemical molecules to elicit cellular differentiation is a common strategy in tissue engineering. However, limitations associated with growth factors, such as short half‐life, high effective physiological doses, and high costs, have prompted the search for growth factor alternatives, such as growth factor mimics and other proteins. This work explores the use of insulin protein as a biochemical factor to aid in tendon healing and differentiation of cells on a biomimetic electrospun micro‐nanostructured scaffold. Dose response studies were conducted using human mesenchymal stem cells (MSCs) in basal media supplemented with varied insulin concentrations. A dose of 100‐ng/mL insulin showed increased expression of tendon markers. Synthetic‐natural blends of various ratios of polycaprolactone (PCL) and cellulose acetate (CA) were used to fabricate micro‐nanofibers to balance physicochemical properties of the scaffolds in terms of mechanical strength, hydrophilicity, and insulin delivery. A 75:25 ratio of PCL:CA was found to be optimal in promoting cellular attachment and insulin immobilization. Insulin immobilized fiber matrices also showed increased expression of tendon phenotypic markers by MSCs similar to findings with insulin supplemented media, indicating preservation of insulin bioactivity. Insulin functionalized scaffolds may have potential applications in tendon healing and regeneration.     

Structural modification of bacterial cellulose

The microfibrillar nature of bacterial cellulose produced by Acetobacter was modified by various chemical reagents in a culture medium. The chemical reagents included antibiotics to inhibit cell division or certain protein synthesis, and reducing reagents that induce reductive cleavage of disulfide bonds in proteins. Among the reagents tested, nalidixic acid and chloramphenicol induced elongation of bacteria, resulting in the formation of wider cellulose ribbons or aggregates of ribbons. The Young's modulus of the sheets made from such cellulose increased, while dithiothreitol, which produced ribbons having only 45% of the width of the control, produced sheets with undiminished Young's modulus. Although further study is necessary to clarify the effect of such modifications, nalidixic acid and chloramphenicol produced a bacterial cellulose with superior mechanical properties.     

Preparation and characterization of the bacterial cellulose/polyurethane nanocomposites

New nanocomposites based on bacterial cellulose nanofibers (BCN) and polyurethane (PU) prepolymer were prepared and characterized by SEM, FT-IR, XRD, and TG/DTG analyses. An improvement of the interface reaction between the BCN and the PU prepolymer was obtained by a solvent exchange process. FT-IR results showed the main urethane band at 2,270 cm^?1 to PU prepolymer; however, in nanocomposites new bands appear as disubstituted urea at 1,650 and 1,550 cm^?1. In addition, the observed decrease in the intensity of the hydroxyl band (3,500 cm^?1) suggests an interaction between BCN hydroxyls and NCO-free groups. The nanocomposites presented a non-crystalline character, significant thermal stability (up to 230 °C) and low water absorption when compared to pristine BCN.     

溶胶凝胶法由细菌纤维素制备CuCe_(0.75)Zr_(0.25)O_x复合氧化物及其低温催化降解甲苯性能

以绿色廉价的天然椰果细菌纤维素(BC)为造孔剂,采用溶胶凝胶法制备了CuCe_(0.75)Zr_(0.25)O_x复合氧化物催化剂,通过TG/DTG、N2低温物理吸脱附、XRD、H_2-TPR、O_2-TPD和Raman等手段对催化剂进行了表征,并对其在固定床上挥发性有机物(VOCs)降解的催化性能进行了研究。结果表明,利用BC精细的纤维网状结构和亲水性能与活性金属盐溶液形成凝胶,可有效制备介孔结构的复合氧化物催化剂。制备过程中,凝胶形式和成胶温度对催化剂降解甲苯的活性有较大影响;采用醇凝胶形式在70℃时制备的ACCZ-70催化剂完全降解甲苯的温度为205℃,明显低于已有文献报道的催化剂,这主要归因于该催化剂具有良好的低温还原性和高达0.81的氧空穴浓度。而采用水凝胶制备的催化剂降解甲苯时,在120-140℃存在吸附现象。     

Solvent-assisted room-temperature compression molding approach to fabricate porous scaffolds for tissue engineering

This study investigated the room-temperature compression molding/particle leaching approach to fabricate three-dimensional porous scaffolds for tissue engineering. Scaffolds with anatomical shapes (ear, joint, tube, cylinder) were made from biodegradable poly(D,L-lactide) and poly[(D,L-lactide)-co-glycolide]. The utility of this room-temperature compression approach comes from the effect of solvent assistance, but the tendency for post-molding scaffold shrinkage is a problem unique to this method and is thus examined with emphasis in this paper. Scaffold shrinkage was found to be tolerable under normal fabrication conditions with high salt contents, which is just what the preparation of highly porous scaffolds requires. Furthermore, the resultant porosities after salt leaching were measured as well as the initial scaffold shrinkages after solvent evaporation, and the relation between them was revealed by theoretical analysis and confirmed by comparison with experimental measurements. The pores were interconnected, and porosity can exceed 90%. The effects of porosity on the mechanical properties of porous scaffolds were also investigated. This convenient fabrication approach is a prospective method for the tailoring of porous scaffolds for a variety of possible applications in tissue engineering and tissue reconstruction.     

The fabrication and characterization of poly(lactic acid) scaffolds for tissue engineering by improved solid–liquid phase separation

In this article a new technique was developed to fabricate scaffolds with a unique microstructure by solid–liquid separation in combination with particulate-leaching. Firstly, the effects of polymer concentration, quenching temperature on the porous morphology and the mechanical property of obtained scaffolds during solid–liquid separation have been investigated. Then, salt granules as porogen were introduced into the solid–liquid phase separation to produce the unique pore structure of the scaffold. The pore diameter of the scaffold could be controlled with the particulate size and the wall of pores possessed special microstructure, which enhanced the pore interconnectivity. The cell culture results confirmed that a good interconnectivity of the scaffold prepared by the improved solid–liquid separation was useful for nutrition transportation and cell proliferation. Copyright © 2003 John Wiley & Sons, Ltd.