Synthesis of well‐designed polymers carrying saccharide moieties via RAFT miniemulsion polymerization

Two hydrophobic vinyl saccharide monomers based on D ‐glucose and D ‐fructose were polymerized by employing the reversible addition‐fragmentation transfer (RAFT) miniemulsion polymerization technique to prepare well‐designed glycopolymers. Three dithiobenzoate‐RAFT agents [S?C(Ph)S? R], 1‐phenylethyl dithiobenzoate (PED), 2‐phenylprop‐2‐yl dithiobenzoate (PPD), and 2‐cyanoprop‐2‐yl dithiobenzoate (CPD), were used to control the growth of polymer chains. The best results were obtained in the presence of the PPD‐RAFT agent and the formed polymers have polydispersity index's (PDI) lower than 1.15. Under adequate miniemulsion polymerization conditions, a glycopolymer with PDI of 1.1 and molecular weight of 5 × 10⁴ g/mol has been successfully synthesized in a short reaction time of 100 min. Furthermore, some block copolymers containing saccharide segment with butyl or methyl methacrylate were prepared. Copyright © 2007 John Wiley & Sons, Ltd.     

2‐Cyanoprop‐2‐yl dithiobenzoate mediated reversible addition–fragmentation chain transfer polymerization of acrylonitrile targeting a polymer with a higher molecular weight

The reversible addition–fragmentation chain transfer (RAFT) polymerization of acrylonitrile (AN) mediated by 2‐cyanoprop‐2‐yl dithiobenzoate was first applied to synthesize polyacrylonitrile (PAN) with a high molecular weight up to 32,800 and a polydispersity index as low as 1.29. The key to success was ascribed to the optimization of the experimental conditions to increase the fragmentation reaction efficiency of the intermediate radical. In accordance with the atom transfer radical polymerization of AN, ethylene carbonate was also a better solvent candidate for providing higher controlled/living RAFT polymerization behaviors than dimethylformamide and dimethyl sulfoxide. The various experimental parameters, including the temperature, the molar ratio of dithiobenzoate to the initiator, the molar ratio of the monomer to dithiobenzoate, the monomer concentration, and the addition of the comonomer, were varied to improve the control of the molecular weight and polydispersity index. The molecular weights of PANs were validated by gel permeation chromatography along with a universal calibration procedure and intrinsic viscosity measurements. ¹H NMR analysis confirmed the high chain‐end functionality of the resultant polymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1272–1281, 2007     

Living free‐radical polymerization of sterically hindered monomers: Improving the understanding of 1,1‐disubstituted monomer systems

The sterically hindered, 1,1‐disubstituted monomers di‐n‐butyl itaconate (DBI), dicyclohexyl itaconate (DCHI), and dimethyl itaconate (DMI) were polymerized with reversible addition–fragmentation chain transfer (RAFT) free‐radical polymerization and atom transfer radical polymerization (ATRP). Cumyl dithiobenzoate, cumyl phenyl dithioacetate, 2‐cyanoprop‐2‐yl dithiobenzoate, 4‐cyanopentanoic acid dithiobenzoate, and S‐methoxycarbonylphenylmethyl dithiobenzoate were employed as RAFT agents to mediate a series of polymerizations at 60 °C yielding polymers ranging in their number‐average molecular weight from 4500 to 60,000 g mol^?1. The RAFT polymerizations of these hindered monomers displayed hybrid living behavior (between conventional and living free‐radical polymerization) of various degrees depending on the molecular structure of the initial RAFT agent. In addition, DCHI was polymerized via ATRP with a CuCl/methyl benzoate/N,N,N′,N″,N″‐pentamethyldiethylenetriamine/cyclohexanone system at 60 °C. Both the ATRP and RAFT polymerization of the hindered monomers displayed living characteristics; however, broader than expected molecular weight distributions were observed for the RAFT systems (polydispersity index = 1.15–3.35). To assess the cause of this broadness, chain‐transfer‐to‐monomer constants for DMI, DBI, and DCHI were determined (1.4 × 10^?3, 1.3 × 10^?3, and 1.0 × 10^?3, respectively) at 60 °C. Simulations carried out with the PREDICI program package suggested that chain transfer to monomer contributed to the broadening process. In addition, the experimental results indicated that viscosity had a pronounced effect on the broadness of the molecular weight distributions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3692–3710, 2006     

Thermoresponsive hyperbranched polymers via In Situ RAFT copolymerization of peg‐based monomethacrylate and dimethacrylate monomers

Here we report the preparation of PEG‐based thermoresponsive hyperbranched polymers via a facile in situ reversible addition‐fragmentation chain transfer (RAFT) copolymerization using bis(thiobenzoyl) disulphide to form 2‐cyanoprop‐2‐yl dithiobenzoate in situ. This novel one‐pot in situ RAFT approach was studied firstly using methyl methacrylate (MMA) monomer, then was used to prepare thermoresponsive hyperbranched polymers by copolymerization of poly(ethylene glycol) methyl ether methacrylate (PEGMEMA, M_n = 475), poly(propylene glycol) methacrylate (PPGMA, M_n = 375) and up to 30 % of ethylene glycol dimethacrylate (EGDMA) as the branching agent. The resultant PEGMEMA‐PPGMA‐EGDMA copolymers from in situ RAFT were characterized by Gel Permeation Chromatography (GPC) and ¹H‐NMR analysis. The results confirmed the copolymers with multiple methacrylate groups and hyperbranched structure as well as RAFT functional residues. These water‐soluble copolymers with tailored compositions demonstrated tuneable lower critical solution temperature (LCST) from 22 °C to 32 °C. The phase transition temperature can be further altered by post functionalization via aminolysis of RAFT agent residues in polymer chains. Moreover, it was demonstrated by rheological studies and particle size measurements that these copolymers can form either micro‐ or macro photocrosslinked gels at suitable concentrations due to the presence of multiple methacrylate groups. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3751–3761     

Latices of poly(fluoroalkyl mathacrylate)‐b‐poly(butyl methacrylate) copolymers prepared via reversible addition–fragmentation chain transfer polymerization

Poly(fluoroalkyl mathacrylate)‐block‐poly(butyl methacrylate) diblock copolymer latices were synthesized by a two‐step process. In the first step, a homopolymer end‐capped with a dithiobenzoyl group [poly(fluoroalkyl mathacrylate) (PFAMA) or poly(butyl methacrylate) (PBMA)] was prepared in bulk via reversible addition–fragmentation chain transfer (RAFT) polymerization with 2‐cyanoprop‐2‐yl dithiobenzoate as a RAFT agent. In the second step, the homopolymer chain‐transfer agent (macro‐CTA) was dissolved in the second monomer, mixed with a water phase containing a surfactant, and then ultrasonicated to form a miniemulsion. Subsequently, the RAFT‐mediated miniemulsion polymerization of the second monomer (butyl methacrylate or fluoroalkyl mathacrylate) was carried out in the presence of the first block macro‐CTA. The influence of the polymerization sequence of the two kinds of monomers on the colloidal stability and molecular weight distribution was investigated. Gel permeation chromatography analyses and particle size results indicated that using the PFAMA macro‐CTA as the first block was better than using the PBMA RAFT agent with respect to the colloidal stability and the narrow molecular weight distribution of the F‐copolymer latices. The F‐copolymers were characterized with ¹H NMR, ¹⁹F NMR, and Fourier transform infrared spectroscopy. Comparing the contact angle of a water droplet on a thin film formed by the fluorinated copolymer with that of PBMA, we found that for the diblock copolymers containing a fluorinated block, the surface energy decreased greatly, and the hydrophobicity increased. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 471–484, 2007     

Block copolymers of dodecafluoroheptyl methacrylate and butyl methacrylate by RAFT miniemulsion polymerization

Reversible addition‐fragmentation chain transfer (RAFT) miniemulsion polymerization of butyl methacrylate (BMA) and dodecafluoroheptyl methacrylate (DFMA) was carried out with 2‐cyanoprop‐2‐yl dithiobenzoate (CPDB) as chain transfer agent (CTA). Concentration effects of RAFT agent and initiator on kinetics and molecular weight were investigated. No obvious red oil layer (phase's separation) and coagulation was observed in the first stage of homopolymerization of BMA. The polymer molecular weights increased linearly with the monomer conversion with polydispersities lower than 1.2. At 75 °C, the monomer conversion could achieve above 96% in 3 h with [momomer]:[RAFT]:[KPS] = 620:4:1 (mole ratio). The results showed excellent controlled/living polymerization characteristics and a very fast polymerization rate. Furthermore, the synthesis of poly(BMA‐b‐DFMA) diblock copolymers with a regular structure (PDI < 1.30, PMMA calibration) was performed by adding the monomer of DFMA at the end of the RAFT miniemulsion polymerization of BMA. The success of diblock copolymerization was showed by the molecular weight curves shifting toward higher molar mass, recorded by gel permeation chromatography before and after block copolymerization. Compositions of block copolymers were further confirmed by ¹H NMR, FTIR, and DSC analysis. The copolymers exhibited a phase‐separated morphology and possessed distinct glass transition temperatures associated with fluoropolymer PDFMA and PBMA domains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1585–1594, 2007     

Reversible addition–fragmentation chain transfer/miniemulsion polymerization of butyl methacrylate in the presence of β‐cyclodextrin

In the presence of β‐cyclodextrin (β‐CD), reversible addition–fragmentation chain transfer (RAFT) polymerization has been successfully applied to control the molecular weight and polydispersity [weight‐average molecular weight/number‐average molecular weight (M_w/M_n)] in the miniemulsion polymerization of butyl methacrylate, with 2‐cyanoprop‐2‐yl dithiobenzoate as a chain‐transfer agent (or RAFT agent) and 2,2′‐azoisobutyronitrile (AIBN) as an initiator. β‐CD acted as both a stabilizer and a solubilizer, assisting the transportation of the water‐insoluble, low‐molecular‐weight RAFT agent into the polymerization loca (i.e., droplets or latex particles) and thereby ensuring that the RAFT agent was homogeneous in the polymerization loca. The polymers produced in the system of β‐CD exhibited narrower polydispersity (1.2 < M_w/M_n < 1.3) than those without β‐CD. Moreover, the number‐average molecular weight in the former case could be controlled by a definite amount of the RAFT agent. Significantly, β‐CD was proved to have a favorable effect on the stability of polymer latex, and no coagulum was observed. The effects of the concentrations of the RAFT agent and AIBN on the conversion, the molecular weight and its distribution, and the particle size of latices were investigated in detail. Furthermore, the influences of the variations of the surfactant (sodium dodecyl sulfate) and costabilizer (hexadecane) on the RAFT/miniemulsion polymerization were also studied. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2931–2940, 2005     

Reversible addition–fragmentation chain‐transfer polymerization: Unambiguous end‐group assignment via electrospray ionization mass spectrometry

Electrospray ionization mass spectrometry was performed to identify the structure of polymeric methyl acrylates generated via the cumyl dithiobenzoate (CDB), cumyl p‐fluorodithiobenzoate (CPFDB), and 1‐phenylethyl dithiobenzoate (PEDB) mediated reversible addition–fragmentation chain‐transfer (RAFT) polymerizations. The relatively simple spectra clearly demonstrate the end groups of this living free‐radical polymerization technique. Only polymeric chains carrying one leaving group of the RAFT agent and the dithiobenzoate end group as the active RAFT center were discovered. Multiple‐stage mass spectrometric experiments and oxidation of the dithioester end group confirmed the structure of the generated polymers. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4032–4037, 2002     

Reversible addition–fragmentation chain transfer polymerization of glycidyl methacrylate with 2‐cyanoprop‐2‐yl 1‐dithionaphthalate as a chain‐transfer agent

A reversible addition–fragmentation chain transfer (RAFT) agent, 2‐cyanoprop‐2‐yl 1‐dithionaphthalate (CPDN), was synthesized and applied to the RAFT polymerization of glycidyl methacrylate (GMA). The polymerization was conducted both in bulk and in a solvent with 2,2′‐azobisisobutyronitrile (AIBN) as the initiator at various temperatures. The results for both types of polymerizations showed that GMA could be polymerized in a controlled way by RAFT polymerization with CPDN as a RAFT agent; the polymerization rate was first‐order with respect to the monomer concentration, and the molecular weight increased linearly with the monomer conversion up to 96.7% at 60 °C, up to 98.9% at 80 °C in bulk, and up to 64.3% at 60 °C in a benzene solution. The polymerization rate of GMA in bulk was obviously faster than that in a benzene solution. The molecular weights obtained from gel permeation chromatography were close to the theoretical values, and the polydispersities of the polymer were relatively low up to high conversions in all cases. It was confirmed by a chain‐extension reaction that the AIBN‐initiated polymerizations of GMA with CPDN as a RAFT agent were well controlled and were consistent with the RAFT mechanism. The epoxy group remained intact in the polymers after the RAFT polymerization of GMA, as indicated by the ¹H NMR spectrum. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2558–2565, 2004     

Reversible Addition–Fragmentation Chain‐Transfer Polymerization of Octadecyl Acrylate

Abstract

Polymerization of octadecyl acrylate (ODA) was carried out in benzene solution using the 2‐cyanoprop‐2‐yl dithiobenzoate (CPDB) as the reversible addition–fragmentation chain‐transfer (RAFT) agent and AIBN as the initiator. The results show the obtained polymer with controlled molecular weight and low PDI value. The relationships between both of the ln([M ₀]/[M]) vs. reaction time and molecular weight vs. conversion showed a straight line. The block copolymer of ODA and styrene (PODA‐b‐PSt) obtained using poly(octadecyl acrylate) (PODA) as a macro‐RAFT agent. The polymers were characterized by ¹H NMR, DSC, and gel permeation chromatograph (GPC). The effect of molar ratio [CPDB]:[AIBN] and reaction temperature on polymerization was investigated.     

Synthesis of tetrazole‐containing azo polymers with properties of photo‐induced birefringence and surface‐relief‐gratings via RAFT polymerization

A novel optically active monomer, 6‐{4‐[4‐(1‐phenyl‐1H‐tetrazol‐5‐yloxy)‐phenylazo] ‐phenoxy}‐hexyl methacrylate (PTPPHMA) bearing tetrazole and azobenzol moieties, was synthesized and polymerized by reversible addition‐fragmentation chain transfer (RAFT) polymerization using 2‐cyanoprop‐2‐yl dithiobenzoate (CPDB) as the RAFT agent and 2, 2′‐azobis(isobutyronitrile) (AIBN) as the initiator. Well‐defined optically active photochromic polyPTPPHMA(PPTPPHMA) was obtained. “Living”/controlled characteristics were observed in the polymerization: well‐controlled molecular weights (M_ns), narrow molecular weight distributions (M_w/M_n) of the polymers and successful chain‐extension of PPTPPHMA with styrene (St) as the second monomer. The photochemical interconversion between trans and cis isomers of PPTPPHMA in N,N′‐dimethyl formamide (DMF) solution was explored under irradiation of ultraviolet light. The photoinduced birefringence on the thin films of PPTPPHMA was investigated. A maximum birefringence of 0.1 was obtained, and no significant change of profiles of the birefringence after several cycles of writing/erasing/rewriting sequences was observed. The surface‐relief‐gratings (SRGs) were induced on the polymer films by interference of Kr⁺ laser beams at 413.1 nm with 35 mW/cm² intensity, the diffraction efficiencies from SRGs were measured to be in the range of 2.0–2.5%. The atomic force microscopy (AFM) results showed the gratings produced on the surfaces of the polymer film. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 682–691, 2008     

Controlled radical polymerization of a trialkylsilyl methacrylate by reversible addition–fragmentation chain transfer polymerization

The reversible addition–fragmentation chain transfer (RAFT) polymerization of a hydrolyzable monomer (tert‐butyldimethylsilyl methacrylate) with cumyl dithiobenzoate and 2‐cyanoprop‐2‐yl dithiobenzoate as chain‐transfer agents was studied in toluene solutions at 70 °C. The resulting homopolymers had low polydispersity (polydispersity index < 1.3) up to 96% monomer conversion with molecular weights at high conversions close to the theoretical prediction. The profiles of the number‐average molecular weight versus the conversion revealed controlled polymerization features with chain‐transfer constants expected between 1.0 and 10. A series of poly(tert‐butyldimethylsilyl methacrylate)s were synthesized over the molecular weight range of 1.0 × 10⁴ to 3.0 × 10⁴, as determined by size exclusion chromatography. As strong differences of hydrodynamic volumes in tetrahydrofuran between poly(methyl methacrylate), polystyrene standards, and poly(tert‐butyldimethylsilyl methacrylate) were observed, true molecular weights were obtained from a light scattering detector equipped in a triple‐detector size exclusion chromatograph. The Mark–Houwink–Sakurada parameters for poly(tert‐butyldimethylsilyl methacrylate) were assessed to obtain directly true molecular weight values from size exclusion chromatography with universal calibration. In addition, a RAFT agent efficiency above 94% was confirmed at high conversions by both light scattering detection and ¹H NMR spectroscopy. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5680–5689, 2005     

Radical‐medicated end‐group transformation of amphiphilic methacrylate random copolymers for modulation of antimicrobial and hemolytic activities

This work describes synthesis of antimicrobial methacrylate copolymers by reversible addition‐fragmentation chain transfer (RAFT) polymerization and examines the versatility of this approach for improving chemical optimization to create potent, non‐toxic antimicrobial polymers. Specifically, this study focuses on the radical‐mediated transformation of end group of antimicrobial peptide‐mimetic polymer. RAFT polymerization using 2‐cyano‐2‐yl‐dithiobenzoate provided a statistical methacrylate copolymer consisting of aminobutyl and ethyl groups in the side chains. The following radical‐mediated modification using free radical initiators successfully transformed the ω‐end group of parent copolymer from dithiobenzoate to a cyanoisobutyl or aminoethyl cyanopentanoate group without any significant changes to the polymer molecular weight. In general, the parent polymer and variants showed a broad spectrum of activity against a panel of bacteria, but low hemolytic activity against human red blood cells. The parent copolymer with the dithiobenzoate end‐group showed highest antimicrobial and hemolytic activities as compared with other copolymers. The copolymers caused membrane depolarization in Staphylococcus aureus, while the ability of copolymers for membrane disruption is not dependent on the end‐group structures. The synthetic route reported in this study will be useful for further study of the role of polymer end‐groups in the antimicrobial activity of copolymers. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 304–312     

Reversible addition–fragmentation chain transfer polymerization of 2‐naphthyl acrylate with 2‐cyanoprop‐2‐yl 1‐dithionaphthalate as a chain‐transfer agent

The reversible addition–fragmentation chain transfer (RAFT) polymerizations of 2‐naphthyl acrylate (2NA) initiated by 2,2′‐azobisisobutyronitrile were investigated with 2‐cyanoprop‐2‐yl 1‐dithionaphthalate (CPDN) as a RAFT agent at various temperatures in a benzene solution. The results of the polymerizations showed that 2NA could be polymerized in a controlled way by RAFT polymerization with CPDN as a RAFT agent; the polymerization rate was first‐order with respect to the monomer concentration, and the molecular weight increased linearly with the monomer conversion. The polydispersities of the polymer were relatively low up to high conversions in all cases. The chain‐extension reactions of poly(2‐naphthyl acrylate) (P2NA) with methyl methacrylate and styrene successfully yielded poly(2‐naphthyl acrylate)‐b‐poly(methyl methacrylate) and poly(2‐naphthyl acrylate)‐b‐polystyrene block polymers, respectively, with narrow polydispersities. The P2NA obtained by RAFT polymerization had a strong ultraviolet absorption at 270 nm, and the molecular weights had no apparent effect on the ultraviolet absorption intensities; however, the fluorescence intensity of P2NA increased as the molecular weight increased and was higher than that of 2NA. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2632–2642, 2005     

Synthesis of comb‐like polystyrene with poly(N‐phenyl maleimide‐alt‐p‐chloromethyl styrene) as macroinitiator

The copolymerization of N‐phenyl maleimide and p‐chloromethyl styrene via reversible addition–fragmentation chain transfer (RAFT) process with AIBN as initiator and 2‐(ethoxycarbonyl)prop‐2‐yl dithiobenzoate as RAFT agent produced copolymers with alternating structure, controlled molecular weights, and narrow molecular weight distributions. Using poly(N‐phenyl maleimide‐alt‐p‐chloromethyl styrene) as the macroinitiator for atom transfer radical polymerization of styrene in the presence of CuCl/2,2′‐bipyridine, well‐defined comb‐like polymers with one graft chain for every two monomer units of backbone polymer were obtained. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2069–2075, 2006     

Synthesis of dendritic carbohydrate end‐functional polymers via RAFT: Versatile multi‐functional precursors for bioconjugations

Well‐defined pyridyl disulfide (PDS) end‐functionalized polymer‐dendritic carbohydrate scaffolds are reported as novel precursors for the attachment of biomolecules. This synthetic approach combines reversible addition fragmentation chain transfer (RAFT) polymerization and “click” reactions. Poly(N‐(2‐hydroxypropyl) methacrylamide) (PHPMA) with 2‐mercaptothiozalidine end‐groups was prepared by RAFT polymerization yielding molecular weights of M_n = 4300 and 9900, both with a polydispersity of less than 1.2. These polymers were then attached to dendritic mannose scaffolds preconstructed via consecutive “click” reactions. Finally, the ω‐dithiobenzoate RAFT end‐group of PHPMA was modified to yield PDS functionality, by aminolysis in the presence of 2,2′‐dithiodipyridine. This PDS end‐functionalized PHPMA‐dendritic carbohydrate scaffold is a versatile precursor for bioconjugations, as the synthetic procedure can easily accommodate a range of sugar functionalities. In addition, the PDS groups can be used to react with any thiol present in a biomolecule (e.g., cysteine residue in proteins, or ? SH terminal nucleotides). To demonstrate the utility of these scaffolds we describe their bioconjugation to short interfering RNA. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4302–4313, 2009     

Facile synthesis of comb,star, and graft polymers via reversible addition–fragmentation chain transfer (RAFT) polymerization

Reversible addition–fragmentation chain transfer (RAFT) polymerization has been shown to be a facile means of synthesizing comb, star, and graft polymers of styrene. The precursors required for these reactions were synthesized readily from RAFT‐prepared poly(vinylbenzyl chloride) and poly(styrene‐co‐vinylbenzyl chloride), which gave intrinsically well‐defined star and comb precursors. Substitution of the chlorine atom in the vinylbenzyl chloride moiety with a dithiobenzoate group proceeded readily, with a minor detriment to the molecular weight distribution. The kinetics of the reaction were consistent with a living polymerization mechanism, except that for highly crowded systems, there were deviations from linearity early in the reaction due to steric hindrance and late in the reaction due to chain entanglement and autoacceleration. A crosslinked polymer‐supported RAFT agent was also prepared, and this was used in the preparation of graft polymers with pendant polystyrene chains. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2956–2966, 2002     

Reversible addition–fragmentation chain transfer mediated radical polymerization of asymmetrical divinyl monomers targeting hyperbranched vinyl polymers

Reversible addition–fragmentation chain transfer (RAFT) mediated radical polymerizations of allyl methacrylate and undecenyl methacrylate, compounds containing two types of vinyl groups with different reactivities, were investigated to provide hyperbranched polymers. The RAFT agent benzyl dithiobenzoate was demonstrated to be an appropriate chain‐transfer agent to inhibit crosslinking and obtain polymers with moderate‐to‐high conversions. The polymerization of allyl methacrylate led to a polymer without branches but with five‐ or six‐membered rings. However, poly(undecenyl methacrylate) showed an indication of branching rather than intramolecular cycles. The hyperbranched structure of poly(undecenyl methacrylate) was confirmed by a combination of ¹H, ¹³C, ¹H–¹H correlation spectroscopy, and distortionless enhancement by polarization transfer 135 NMR spectra. The branching topology of the polymers was controlled by the variation of the reaction temperature, chain‐transfer‐agent concentration, and monomer conversion. The significantly lower inherent viscosities of the resulting polymers, compared with those of linear analogues, demonstrated their compact structure. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 26–40, 2007     

Facile synthesis of controlled‐structure primary amine‐based methacrylamide polymers via the reversible addition‐fragmentation chain transfer process

We report here a novel direct method for the syntheses of primary aminoalkyl methacrylamides that requires mild reagents and no protecting group chemistry. The reversible addition‐fragmentation chain transfer polymerization (RAFT) of the aminoalkyl methacrylamide revealed to be highly efficient with 4‐cyanopentanoic acid dithiobenzoate (CTP) as chain transfer agent and 4,4′‐azobis(4‐cyanovaleric acid) (ACVA) as initiator. Cationic amino‐based homopolymers of reasonably narrow polydispersities (M_w/M_n < 1.30) and predetermined molecular weights were obtained without recourse to any protecting group chemistry. A range of block and random copolymers were also synthesized via the RAFT process. The homopolymers and copolymers were characterized by aqueous conventional and triple detection gel permeation chromatography systems. Furthermore, the primary amine‐based methacrylamide monomers and polymers revealed to be highly stable both with the primary amino group in the protonated and deprotonated form. We have also demonstrated that stabilized gold nanoparticles can be generated with the RAFT‐synthesized amine‐based polymers via a photochemical process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4984–4996, 2008     

Highly efficient and well‐controlled ambient temperature RAFT polymerization of glycidyl methacrylate under visible light radiation

A range of well‐defined poly(glycidyl methacrylate) (PGMA) polymers and their corresponding block copolymers were synthesized via 2‐cyanoprop‐2‐yl(4‐fluoro) dithiobenzoate or CPFDB‐mediated ambient temperature reversible addition fragmentation chain transfer radical polymerization or RAFT polymerization under environmentally friendly visible light radiation (λ = 405–577 nm), using a (2,4,6‐trimethylbenzoyl) diphenylphosphine oxide photoinitiator. As comparison, CPFDB‐mediated ambient temperature RAFT polymerizations of glycidyl methacrylate (GMA) under both full‐wave radiation (λ = 254–577 nm) and long‐wave radiation (λ = 365–577 nm) were also studied in this article. The results indicated that CPFDB moieties were significantly photolyzed under either full‐wave radiation or long‐wave radiation, thus undermining the controlled behavior of these RAFT processes. Whereas this photolysis was significantly suppressed under visible light radiation, thus CPFDB functionalities exerted well control over RAFT process, leading to a remarkably living behavior up to 90% GMA monomer conversions. This strategy facilitates the facile synthesis of well‐defined PGMA polymers. More importantly, under visible light radiation, a relatively high initial molar ratio of GMA to CPFDB and TPO led to shortening initialization period of RAFT process and accelerating overall polymerization rate. These effects are remarkably in favor of the facile synthesis of well‐defined PGMA polymers and PGMA‐based copolymers with high molecular weights. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5091–5102, 2007