On the formation and properties of a high-temperature resin from a bisphthalonitrile

When 4,4'-bis (3,4-dicyanophenoxy) biphenyl is heated with small amounts of aromatic amine or amidine salts, a highly crosslinked polytriazine is obtained. This polymer has been shown to be the same as that reported when bisphthalonitriles are heated with amines. Salts promote this reaction more readily and the glass transition temperature of the polymer after post-cure at 315°C is generally 30°C higher than when free bases are used. The fracture properties and elasticity of the salt-cured polymer have been measured at temperatures up to 250°C. As a model system, the self reaction of phthalonitrile promoted by amines and their salts has been studied. In both cases, poly[4-(2-cyanophenyl)-1,3,5-triazine-2,6-diyl-1,2-phenylene] is produced, and more efficiently using the salts. A reaction mechanism for this polymerization has been proposed. © 1994 John Wiley & Sons, Inc.     

Temperature effect on conducting polyaniline salts: Thermal and spectral studies

Five different polyaniline salts have been prepared by chemical polymerization of aniline in aqueous solution of different acids. Polyaniline samples have been heat treated at four different temperatures (150, 200, 275, and 375°C) and characterized by electron paramagnetic, electronic absorption, and infrared spectral measurements. Thermal stabilities of the chemically synthesized polyaniline salts have been studied by thermal analysis and spectral methods. Polyaniline salts undergo a three-step weight-loss process in the heating cycle. The first step (up to 110°C) corresponds to the loss of water molecules from the polymer chain. In the second step (110–275°C), a small amount of acid escapes as volatile gas, and after 275°C the polymer undergoes oxidative thermal degradation in the third step. It was found that thermal stability of polyaniline salts depends on the counteranion used and the polymer is apparently stable up to 250°C. No structural changes have taken place up to 200°C and this has been confirmed from infrared and electronic absorption spectra. No definite correlation exists between conductivity and spin concentration. © 1994 John Wiley & Sons, Inc.     

Theoretical interpretation of the existence at 35°C of an absolute maximum of the hydration rate of calcium sulfate hemihydrate

Isothermal calorimetric measurements of β-CaSO₄ · 0.5 H₂O hydration by liquid water between 5 and 50°C show that the hydration rate passes through a maximum at about 35°C. This phenomenon is explained theoretically by consideration of the crystallization and dissolution constant rates and the solubility diagram.It results from the fact that the usual increase of rate constants with temperature is associated with a variation, in opposite directions of the positive difference of solubility between the two salts. This phenomenon is certainly general and may be found in the study of other pairs of salts.     

N-alkyl-4-(N′,N′-dialkylamino)pyridinium salts: thermally stable phase transfer catalysts for nucleophilic aromatic displacement

N-Alkyl salts of 4-dialkylaminopyridines are effective phase transfer catalysts which are up to 100 times more stable than tetrabutylammonium bromide to conditions encountered in nucleophilic aromatic substitution reactions. These salts are thermally stable to over 300°C, and promote reactions in non-polar solvents (or in the absence of solvent) at temperatures as high as 200°C.     

Shape-controlled Synthesis of Nanostructure Ramsdellite-type Manganese Oxide at Atmospheric Pressure

Ramsdellite (R‐MnO₂) was prepared by oxidizing bivalent manganese salts, such as MnCl₂, MnSO₄ and Mn(NO₃)₂, with NaClO solution using a refluxing process at atmospheric pressure. The products were characterized by X‐ray diffraction, fourier transform infrared spectroscopy, transmission electron microscopy, scanning electron microscopy and flame photometry. R‐MnO₂ microstructure and morphology were controlled by adjusting reaction temperature, the amount of hydrochloric acid (HCl) and anions of bivalent manganese salts. Ramsdellite grain was formed with three different bivalent manganese salts oxidized by NaClO solution at 60°C, and increased with the increase of reflux temperature. R‐MnO₂ nanorod and nanowire crystals were obtained when MnCl₂ and MnSO₄ were used as bivalent manganese salts at 100°C respectively. Nanosized flake of R‐MnO₂ came into being when Mn(NO₃)₂ was applied at 80°C. When 30 mmol MnCl₂ was oxidized by 60 mmol NaClO solution with adding 20 mmol HCl in refluxing solution, specific surface area of R‐MnO₂ grain obtained at 60°C was greater than 140 m²/g, and the self‐assembly of nanorod bundles into interesting flowerlike architectures was achieved at 100°C. The process of dissolution‐precipitation equilibrium might be the primary cause for the morphology transformation.     

Thermal studies on the sodium salts of aminosalicylic acids

The effect on the stability of the isomers of aminosalicylic acid of formation of their sodium salts has been studied by use of differential scanning calorimetry and thermogravimetry, coupled with evolved gas analysis by Fourier transform infrared spectroscopy. X-ray powder diffraction and infrared spectroscopy provided complementary information. The DSC curves for the sodium salts of all of the isomers showed complex dehydration/decomposition endotherms. From the initial mass losses of the TG curves, the amounts of water per mole of salt were estimated as 0.5, 2.4 and 1.4 moles for the sodium salts of 3-aminosalicylic acid, 4-aminosalicylic acid and 5-aminosalicylic acid, respectively. TG-FTIR results for the sodium salt of 3-aminosalicylic acid showed the evolution of carbon dioxide in three stages: below 150°C, between 200 and 300°C and continuous formation up to 500°C. This behaviour differs from that of 3-aminosalicylic acid itself, which forms CO₂ between 225 and 290°C. For the sodium salt of 4-aminosalicylic acid, the formation of carbon dioxide starts from 250°C and is still being formed at about 650°C. 4-aminosalicylic acid decarboxylates above 150°C. 5-aminosalicylic acid and its sodium salt showed no evolution of carbon dioxide below 600°C. This revised version was published online in July 2006 with corrections to the Cover Date.     

Dielectric relaxation in ethylene–methacrylic acid copolymers and their salts

Dielectric relaxation data have been obtained for two ethylene–methacrylic acid copolymers (containing about 4 mole-% methacrylic acid units and about 8 mole-% methacrylic acid units, respectively) and the lithium, sodium, and calcium salts prepared by partial neutralization of the polyacids. The frequency range employed was from 50 Hz to 10 kHz and the temperature range was from ?130°C to 100°C. Attention is focused on three dielectric loss regions labeled β, β and α in order of increasing temperature. The β′ process (?10°C at 100 Hz in the salts only) correlates with a mechanical loss process previously reported and is attributed to microbrownian motion taking place in an amorphous hydrocarbon phase. The β′ process (20°C at 100 Hz) has also been observed mechanically and is attributed to the same mechanism as the β process. The higher temperature of this relaxation compared to the β relaxation is attributed to the presence of acid groups which form crosslinks composed of interchain hydrogen bonds. The α process (>50°C at 100 Hz in the salts only) correlates with dielectric and NMR data previously reported for a sodium salt and is assigned to motions within ionic domains formed by the clustering of salt groups.     

Application of high-melting pyridinium salts as ionic liquid catalysts and media for fischer esterification

Pyridinium methanesulfonate (m.p. 185°C) and pyridinium p-toluenesulfonate (m.p. 121°C) were used as catalysts and media for the esterification of carboxylic acids with primary alcohols to give the corresponding esters selectively in high yields. The high melting points of these pyridinium salts did not prevent their application as ionic liquid medium for these reactions which were performed at 90°C.     

Thermal decyanation,a new organic reaction. II

When heated in solution at about 160°C, pyridine quaternary salts of bromomalonamides lose 1 mole of cyanic or isocyanic acid almost quantitatively in a manner quite analogous to the decarboxylation of an acid. By DTA and DSC, the crystalline salts are stable up to their melting points (>220°C) at which temperatures concurrent fusion and decyanation processes occur (endotherm); these are immediately followed by an exotherm related to the trimerization of cyanic acid. TGA measurements on the solid salts do not clearly define the loss of 1 mole of cyanic acid because in the solid state, thermal decyanation is accompanied to some extent by other pyrolytic reactions. Preparative methods for quaternizing poly(4-vinylpyridine) with bromomalonamide are described and two polymeric quaternary salts (33 and 100% substituted) were prepared and analyzed. These polyelectrolytes are water soluble and upon the addition of base the yellow polymeric nitrogen ylids are generated. Infrared spectra on the polymeric quaternary salts and visible spectra on the polymeric ylids are included. The ylid chromophore has an ε = 1800 at λ_max = 415 nm. The dilute solution viscosity behavior of these polymers in H₂O and in 0.05N KBr is typical of polyelectrolytes. Both polymers in dilute solution show a maximum in η_sp versus pH plots. In water, the viscosity of these polymers decreases with time, and it is proven that this results from a conformational change which accompanies amide hydrolysis rather than polymer backbone degradation. Glass transitions are not detectable by DTA but both polymers show well-defined trimerization exotherms for cyanic acid starting at 170–175°C. Thus, decyanation of the solid polymeric quaternary salts is more analogous to decyanation of the crystalline quaternarys in solution than as solids. TGA measurements on the polymers show weight losses which are of the correct order of magnitude and in the correct temperature range for monodecyanation. Some data are presented which suggest that perhaps a second mole of cyanic acid is lost at about 250°C. Quaternization of poly(4-vinylpyridine) with bromomalonamide reduces its gross decomposition temperature from 385°C to about 285–317°C. It is demonstrated how thermal decyanation can be used for the in situ generation of cyanic acid for the modification of organic compounds. The preparation of a partial urethane of poly(vinyl alcohol) using this method is described. We have also shown that aliphatic quaternary salts can be prepared and that they too undergo the decyanation reaction.     

La matrice eau de mer et le signal du cuivre en spectrometrie d'adsorption atomique sans flamme : Partie 1: Etude de l'influence des principaux composants

(Copper signals from seawater matrices in electrothermal atomic absorption spectrometry. Part 1: study of the effects of principal inorganic ions.)The effects of the main inorganic ions of seawater (Na⁺, Mg²⁺, Ca²⁺, Cl^?, SO^2?₄), and of nitrate as modifier, on the electrothermal atomic absorption spectrometric signal of copper are studied. Sodium chloride, sulfate or nitrate, magnesium chloride or nitrate, and calcium chloride can cause serious interferences. Thermal treatment at about 700°C prevents the interference of MgCl₂ by its hydrolysis. Ashing can be done without loss of copper at higher temperatures in the presence of sulfate salts (1300°C) and nitrate salts (1200°C) than in the presence of chloride salts (1100°C). This is ascribed to the stabilising effect of oxides and sulfides. A study of the influence of two-component matrices, MCl-MNO₃ or MCl-MSO₄, on the atomization signal of copper confirms this stabilizing effect which adds to the decrease in interference connected with removal of chloride in acidic medium.     

Steric and Inductive Effects on Ionic Association in Aqueous Solutions Using an ion Selective Electrode Technique. II. Magnesium Salts

The stoichiometric association constants, K, the thermodynamic association constants, K_A, and the thermodynamic parameters ΔS°, ΔH°, ΔG° for the association between Mg(II) ion with o-, m and p-toluates,o-,m, and p-chlorobenzoates, and o-, m- and p-bromobenzoates have been determined at 15°C, 25°C, 35°C and 45°C in aqueous media. Ion selective electrodes were used to measure the Mg^{2 +} activities. The trends in the association behavior of Mg(II) salts of aromatic acids connot be explained on the basis of steric effects but can be explained according to the trend of the pKa of the parent organic acids, and the Hammett function, σ, of the salts themselves relative to the corresponding benzoate salt.     

Application of S‐alkylsulfonium salts of aromatic sulfides as new thermal latent cationic initiators

The cationic initiation activity of derivatives of S‐methylsulfonium salts of dibenzothiophene ( 3a ), diphenyl sulfide ( 4a ), thioanisole ( 4d ), and tetrahydrothiophene ( 5 ) was evaluated in the polymerization of glycidyl phenyl ether ( 1 ). These initiators were soluble in 1 and capable of initiating the cationic polymerization of 1 on heating, with the exception of methyltetrahydrothiophenium tetrafluoroborate ( 5 ; in the range of room temperature to 160 °C). Among them, methyldiphenylsulfonium tetrafluoroborate ( 4a ) showed a moderate thermal latency that brought about the polymerization of 1 efficiently at 160 °C but not below 80 °C. S‐Alkylsulfonium salts of aromatic sulfides such as phenoxathiin ( 6a ) and thianthrene ( 6b ) also were evaluated for their activity in the cationic polymerization of 1 , from which the thermal latent behavior of these salts also was confirmed (i.e., there was no reaction at 60 °C for 3 h, but there was a high enough conversion at 140 °C). Furthermore, the catalytic activity of S‐alkylsulfonium derivatives was controllable by both the property of the substituents on the aromatic rings and the character of the alkyl groups on the sulfur atom. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 18–27, 2000     

Ionic strength/temperature-induced gelation of aqueous poly(N-isopropylacrylamide-co-vinylimidazole) solution

A high molecular weight copolymer of N-isopropylacrylamide (NiPAAm) and vinyl imidazole (VI) was synthesized and its phase transition behavior in aqueous solutions (5 wt%) by simultaneous changes of ionic strength and temperature was investigated. At low ionic strengths, the copolymer solution showed two phases (clear and opaque solutions), which were freely mobile, as increasing temperatures up to 65°C due to repulsion interaction of positive charges developed by basic imidazole group on the polymer aggregates. However, at the physiological condition (I=0.15, T=37°C), four distinctive phases (clear solution, opaque solution, gel and shrunken gel) were observed because of charge shielding effect by added salts. The gel state was stable and maintained from 32°C to 55°C. In particular, the phase transition from opaque solution to gel rapidly occurred by the change in ionic strength (from ∼ 0 to 0.15) at 37°C. This characteristic can be utilized as a liquid embolic agent.     

Al(Cap)3 as initiator in the anionic polymerization of ε-caprolactam at high temperature

Mechanism for polymerization of ε-caprolactam in the presence of both sodium and aluminum caprolactamate was investigated at 171°C. The role of Al(Cap)₃ as an initiator was revealed. The apparent rate constant of propagation reaction decreased with the increase in the concentration of Al(Cap)₃, as the two different metal salts interact even at 171°C. The activation energy of the overall polymerization reaction with this catalyst system was estimated to be 41.18 kcal/mole.     

Thermotropic liquid-crystalline properties of extended viologen bis(triflimide) salts

A series of extended, symmetric viologen triflimides were synthesised by the metathesis reaction of lithium triflimide with the respective viologen tosyalates in methanol. Their chemical structures were characterised by Fourier Transform Infrared, ¹H and ¹³C Nuclear Magnetic Resonance spectroscopy and elemental analysis. Their thermotropic liquid-crystalline (LC) properties were examined by a number of experimental techniques including differential scanning calorimetry, thermogravimetric analysis, polarising optical microscopy and variable temperature X-ray diffraction. The viologen salts containing alkyl chain of two carbon and three carbon atoms were relatively low melting salts. Those of alkyl chains of four carbon and five carbon atoms formed ionic liquids at 88 and 42°C, respectively. Those of alkyl chain of 9, 10 and 11 carbon atoms were high melting salts, as high as 166°C. Those of higher alkyl chains of 16, 18 and 20 carbon atoms showed thermotropic LC phases forming SmC, SmA and an unidentified smectic (SmX) phases, and showed SmA to isotropic transitions at high temperatures. As expected, all the viologen triflimides had excellent stabilities in the temperature range of 338–365°C.     

Thermally induced cationic polymerization of divinyl ethers using iodonium and sulfonium salts

Cationic polymerization of diethyleneglycoldivinyl ether was thermally induced by diphenyliodonium, alkylbenzylsulfonium, and phenacyltetramethylenesulfonium salts. The reactivity was enhanced by using free radical sources in combination with diphenyliodonium or phenacyltetramethylenesulfonium salts. Even at low onium salt concentrations extremely reactive formulations could be obtained, e.g., the polymerization was complete within 1 minute at 100°C when using the most reactive salts. Polymerizations were induced at temperatures ranging from 50 to 180°C. The Counterion, Supplied by the onium salts, strongly influenced the appearance of the resulting crosslinked polymer: salts containing SbF⁻₆ usually gave highly discolored samples due to the large heat evolution during polymerization whereas polymerization with PF⁻₆ proceeded smoother resulting in transparent, uncolored polymers. The purity of the monomer greatly affected the initiation by the diphenyliodonium and phenacyltetramethylenesulfonium salts. Adventitious radical sources, e. g., hydroperoxides on oxidized monomer, lowered the activation temperature but also led to poor storage stability of these formulations.     

Spectral and thermal characterization of polyaniline–oxalic acid salt

Polyaniline–oxalic acid salts were prepared at 5 and 30°C by chemical polymerization of aniline using different concentration of oxalic acid. Polyaniline base was obtained from the corresponding polyaniline salt by dedoping using aqueous ammonium hydroxide solution. Conductivity measurements, elemental analysis, Infrared, electronic absorption, electron paramagnetic resonance spectral, and thermogravimetric analysis were performed on the polyaniline salts and bases. Composition and the extent of dopant in polyaniline salt systems where determined. The value of composition of polyaniline: oxalic acid is 4: 1.6 and the polymer yield is around 66%. The value of conductivity, polymer yield and composition of polyaniline–oxalic acid salt is independent of concentration of oxalic acid used and also the synthesis temperature. The results are compared with polyaniline–hydrochloride salt prepared by chemical polymerization. The conductivity of polyaniline–oxalic acid salt is three orders of magnitude lower than that of polyaniline-hydrocholoride salt. © 1995 John Wiley & Sons, Inc.     

Thermal behavior and dismantlability of adhesives containing various inorganic salts

As a fundamental study on the development of dismantlable adhesives containing chemically reactive materials, the thermal behavior and dismantlability of an epoxy adhesive containing one of the twenty-seven inorganic salts (chlorides, perchlorates, and nitrates) were observed. In the thermal behavior measured by the differential scanning calorimetry, epoxy adhesives with inorganic salts containing iron, copper, zinc, and aluminum cations released heats of reaction at lower temperatures than the adhesive alone or the adhesives with other inorganic salts. Since such inorganic salts were considered to be effective candidates as fillers in dismantlable adhesives, the adhesion strengths of their mixtures with the adhesive were observed after heat aging at 270 °C for 30 min. The results showed that both chloride and perchlorate salts specifically decreased the adhesion strength after heating. On the other hand, the effect of nitrate salts on the decrease in adhesion strength was low in comparison with the chloride and perchlorate salts.     

Cationic polymerization of vinyl compounds in the presence of tetra-n-butylammonium salts

The effects of salts were examined in cationic polymerization of vinyl compounds. Cationic polymerization of styrene was carried out at 0°C, with acetyl perchlorate, stannic chloride, stannic chloride–trichloroacetic acid and boron trifluoride etherate as catalysts. Tetra-n-butylammonium perchlorate, fluoroborate and iodide were used as salts. The presence of small amounts of the salts changed both the polymerization rate and the molecular weight of polymer considerably. The consideration of various effects led to the conclusion that the results are explicable principally on the basis of counterion exchange. To confirm this, the copolymerization of 2-chloroethyl vinyl ether with γ-methylstyrene was investigated at ?78°C. The copolymer composition curve when stannic chloride was used as catalyst was changed and coincided with that of polymer obtained with acetyl perchlorate catalysis when the perchlorate salt was added. This supports the concept of counterion exchange.     

Properties of aluminium oxides obtained by calcination of the products of reductive roasting of basic aluminium-potassium sulfate

The influence of calcination conditions on changes in phase composition and porous structure was studied for hydrous aluminium oxide, obtained by leaching out potassium salts from the products of roasting basic aluminium-potassium sulfate in hydrogen atmosphere at 600°C. The product of calcination at 350°C in vacuum has the most developed porous structure with most pores of internal radius within 10–60 Å. Calcination in air atmosphere at temperatures 700, 800, 900, or 1000°C resulted in decrease of specific surface of aluminium oxide and increase of the share of pores with internal radius above 60 Å in the overall porosity of the samples. The reconstruction of the porous structure proceeds mainly as a result of coalescent sintering.