Synthesis of sulfonated poly(imidoaryl ether sulfone) membranes for polymer electrolyte membrane fuel cells

New sulfonated poly(imidoaryl ether sulfone) copolymers derived from sulfonated 4,4′‐dichlorodiphenyl sulfone, 4,4′‐dichlorodiphenyl sulfone, and imidoaryl biphenol were evaluated as polymer electrolyte membranes for direct methanol fuel cells. The sulfonated membranes were characterized with Fourier transform infrared spectroscopy, thermogravimetric analysis, and proton nuclear magnetic resonance spectra. The state of water in the membranes was measured with differential scanning calorimetry, and the existence of free water and bound water was discussed in terms of the sulfonation level. The 10 wt % weight loss temperatures of these copolymers were above 470 °C, indicating excellent thermooxidative stability to meet the severe criteria of harsh fuel‐cell conditions. The proton conductivities of the membranes ranged from 3.8 × 10^?2 to 5 × 10^?2 S/cm at 90 °C, depending on the degree of sulfonation. The sulfonated membranes maintained the original proton conductivity even after a boiling water test, and this indicated the excellent hydrolytic stability of the membranes. The methanol permeabilities ranged from 1.65 × 10^?8 to 5.14 × 10^?8 cm²/s and were lower than those of other conventional sulfonated ionomer membranes, particularly commercial perfluorinated sulfonated ionomer (Nafion). The properties of proton and methanol transport were discussed with respect to the state of water in the membranes. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5620–5631, 2005     

Synthesis of highly sulfonated polybenzimidazoles by direct copolymerization and grafting

A series of highly sulfonated, ether‐containing polybenzimidazoles (SOPBI) with controlled sulfonation degrees were synthesized from various stoichiometric ratio mixtures of sodium 6,6'‐oxybis(3‐carboxybenzenesulfonate) (SODBA), 4,4'‐oxydibenzoic acid (ODBA), and 3,3'‐diaminobenzidine (DAB) by solution copolycondensation in poly(phosphoric acid). The resulting sulfonated polymers were further sulfonated by grafting of pendant sulfonic acid chains via a reaction of 1,3‐propane sultone with lithiated‐N of the imidazole rings in the polymer backbone, yielding materials with high, absolute IEC values (3.42–4.15 meq g^?1). Due to self‐neutralization, the solid state polymers possessed “free” acid content of 1.40 to 2.15 meq g^?1, were soluble in organic solvents yet insoluble in aqueous solution, while displaying proton conductivites (11–47 mS cm^?1) at elevated temperatures (80 °C, 95% RH). © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3654–3666     

Synthesis and properties of novel sulfonated (co)polyimides bearing sulfonated aromatic pendant groups for PEFC applications

Novel sulfonated diamines bearing aromatic pendant groups, namely, 3,5‐diamino‐3′‐sulfo‐4′‐(4‐sulfophenoxy) benzophenone (DASSPB) and 3,5‐diamino‐3′‐sulfo‐4′‐(2,4‐disulfophenoxy) benzophenone (DASDSPB), were successfully synthesized. Novel side‐chain‐type sulfonated (co)polyimides (SPIs) were synthesized from these two diamines, 1,4,5,8‐naphthalene tetracarboxylic dianhydride (NTDA) and nonsulfonated diamines such as 4,4′‐bis(3‐aminophenoxy) phenyl sulfone (BAPPS). Tough and transparent membranes of SPIs with ion exchange capacity of 1.5–2.9 meq g^?1 were prepared. They showed good solubility and high thermal stability up to 300 °C. They showed isotropic membrane swelling in water, which was different from the main‐chain‐type and sulfoalkoxy‐based side‐chain‐type SPIs. The relative humidity (RH) and temperature dependence of proton conductivity were examined. At low RH, the novel SPI membranes showed much higher conductivity than the sulfoalkoxy‐based SPIs. They showed comparable or even higher proton conductivity than Nafion 112 in water at 60 °C (>0.10 S cm^?1). The membrane of NTDA‐DASDSPB/BAPPS (1/1)‐s displayed reasonably high proton conductivities of 0.05 and 0.30 S cm^?1 at 50 and 100% RH, respectively, at 120 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2862–2872, 2006     

Characterization and evaluation of commercial poly (vinylidene fluoride)‐g‐sulfonatedPolystyrene as proton exchange membrane

The possibility of developing low‐cost commercial grafted and sulfonated Poly(vinylidene fluoride) (PVDF‐g‐PSSA) membranes as proton exchange membranes for fuel cell applications have been investigated. PVDF‐g‐PSSA membranes were systematically prepared and examined with the focus of understanding how the polymer microstructure (degree of grafting and sulfonation, ion‐exchange capacity, etc) affects their methanol permeability, water uptake, and proton conductivity. Fourier transform infrared spectroscopy was used to characterize the changes of the membrane's microstructure after grafting and sulfonation. The results showed that the PVDF‐g‐PSSA membranes exhibited good thermal stability and lower methanol permeability. The proton conductivity of PVDF‐g‐PSSA membranes was also measured by the electrochemical impedance spectroscopy method. It was found that the proton conductivity of PVDF‐g‐PSSA membranes depends on the degree of sulfonation. All the sulfonated membranes show high proton conductivity at 92°C, in the range of 27 to 235 mScm⁻¹, which is much higher than that of Nafion212 (102 mScm⁻¹ at 80°C). The results indicated that the PVDF‐g‐PSSA membranes are particularly promising membranes to be used as polymer electrolyte membranes due to their excellent stability, low methanol permeability, and high proton conductivity.     

Synthesis and properties of novel sulfonated polyimides containing binaphthyl groups as proton‐exchange membranes for fuel cells

A novel sulfonated diamine monomer, 2,2′‐bis(p‐aminophenoxy)‐1,1′‐binaphthyl‐6,6′‐disulfonic acid (BNDADS), was synthesized. A series of sulfonated polyimide copolymers containing 30–80 mol % BNDADS as a hydrophilic component were prepared. The copolymers showed excellent solubility and good film‐forming capability. Atomic force microscopy phase images clearly showed hydrophilic/hydrophobic microphase separation. The relationship between the proton conductivity and degree of sulfonation was examined. The sulfonated polyimide copolymer with 60 mol % BNDADS showed higher proton conductivity (0.0945–0.161 S/cm) at 20–80 °C in liquid water. The membranes exhibited methanol permeability from 9 × 10^?8 to 5 × 10^?7 cm²/s at 20 °C, which was much lower than that of Nafion (2 × 10^?6cm²/s). The copolymers were thermally stable up to 300 °C. The sulfonated polyimide copolymers with 30–60 mol % BNDADS showed reasonable mechanical strength; for example, the maximum tensile strength at break of the sulfonated polyimide copolymer with 40 mol % BNDADS was 80.6 MPa under high moisture conditions. The optimum concentration of BNDADS was found to be 60 mol % from the viewpoint of proton conductivity, methanol permeability, and membrane stability. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 222–231, 2007     

Sulfonated poly(aryl ether ether ketone ketone)s containing fluorinated moieties as proton exchange membrane materials

A series of sulfonated poly(aryl ether ether ketone ketone)s statistical copolymers with high molecular weights were synthesized via an aromatic nucleophilic substitution polymerization. The sulfonation content (SC), defined as the number of sulfonic acid groups contained in an average repeat unit, could be controlled by the feed ratios of monomers. Flexible and strong membranes in sodium sulfonate form could be prepared by the solution casting method, and readily transformed to their proton forms by treating them in 2 N sulfuric acid. The polymers showed high T_gs, which increased with an increase in SC. Membranes prepared from the present sulfonated poly(ether ether ketone ketone) copolymers containing the hexafluoroisopropylidene moiety (SPEEKK‐6F) and copolymers containing the pendant 3,5‐ditrifluoromethylphenyl moiety (SPEEKK‐6FP) had lower water uptakes and lower swelling ratios in comparison with previously prepared copolymers containing 6F units. All of the polymers possessed proton conductivities higher than 1 × 10^?2 S/cm at room temperature, and proton conductivity values of several polymers were comparable to that of Nafion at high relative humidity. Their thermal stability, oxidative stability, and mechanical properties were also evaluated. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2299–2310, 2006     

Sulfonated poly(meta‐phenylene isophthalamide)s as proton exchange membranes

Random and block sulfonated poly(meta‐phenylene isopthalamide)s as proton exchange membranes were synthesized through the Higashi‐Yamazaki phosphorylation method. Polymers with different degrees of sulfonation from 40 to 100 mol percent were prepared by adjusting the molar feed ratio of 5‐sulfoisophthalic acid sodium salt (SIPA) and isophthalic acid (IPA) in the reaction with meta‐phenylene diamine. Creasable polymer films were obtained by casting DMSO polymer solutions and the membrane films could be exchanged to the proton form in strong acid. ¹H NMR spectroscopy and titration confirmed the degree of sulfonation. Thermogravimetric analysis demonstrated good thermal stabilities with 5% weight loss greater than 380 °C. The copolymers with low degrees of sulfonation (DS = 40 mol %) exhibited low water uptake (water uptake < 17 wt %) at room temperature. A segmented multiblock copolymer prepared by preforming a sulfonated block showed lower water uptake at high temperatures than the random polymer with the same DS of 40 mol % and displayed stability in water up to 80 °C. Both random and block copolymers showed higher proton conductivities at high temperature than that of Nafion‐117 under 95% relative humidity. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2582–2592     

Synthesis and characterization of sulfonated copolyethersulfones

The present article deals with the synthesis and characterization of some sulfonated copolyethersulfones. The synthetic approach differs from the post sulfonation approach traditionally reported in the literature. The synthetic procedure is based on the use of sulfonated monomers which are then reacted with previously synthesized telechelic hydoxy‐ended poly (ether sulpnone)s. Combining the MALDI‐TOF MS and ¹H NMR analyses, with SEC‐Viscometry and TGA measurements, we demonstrate a powerful tool for characterizing the chemical composition, end chains, degree of sulfonation (DS) and molecular mass distribution (MMD) of disulfonated poly(arylene ether‐sulfone) copolymers. The characterization techniques allowed to determine the exact nature of the copolymers synthesized and to reveal some interesting features about the reaction. DMA data show that the glass transition temperature of sulfonated copolymers with similar DS increase as raise their MMD. Copolymers with a DS of 10–11 mol % reach a T_g of 244–246 °C. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3010–3023, 2010     

Sulfonated poly(aryl ether ketone)s containing naphthalene moieties obtained by direct copolymerization as novel polymers for proton exchange membranes

A series of sulfonated poly(aryl ether ketone)s (SPAEKs) were prepared by aromatic nucleophilic polycondensation of 2,6‐dihydroxynaphthalene with 5,5′‐carbonyl‐bis(2‐fluorobenzenesulfonate) and 4,4′‐difluorobenzophenone. The structure and degree of sulfonation (DS) of the SPAEKs were characterized using ¹H NMR spectroscopy. The experimentally observed DS values were close to the expected values derived from the starting material ratios. The thermal stabilities of the SPAEKs were characterized by thermogravimetric analysis, which showed that in acid and sodium salt forms they were thermally stable in air up to about 240 and 380 °C, respectively. Transparent membranes cast from the directly polymerized SPAEKs exhibited good mechanical properties in both dry and hydrated states. The dependence of water uptake and of membrane swelling on the DS at different temperatures was studied. SPAEK membranes with a DS from 0.72 to 1.60 maintained adequate mechanical properties after immersion in water at 80 °C for 24 h. The proton conductivity of SPAEK membranes with different degrees of sulfonation was measured as a function of temperature. The proton conductivity of the SPAEK films increased with increased DS, and the highest room temperature conductivity (4.2 × 10^?2 S/cm) was recorded for a SPAEK membrane with a DS of 1.60, which further increased to 1.1 × 10^?1 S/cm at 80 °C. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2866–2876, 2004     

Chemically modified proton‐conducting membranes based on sulfonated polyimides: Improved water stability and fuel‐cell performance

A series of branched/crosslinked sulfonated polyimide (B/C‐SPI) membranes were prepared and evaluated as proton‐conducting ionomers based on the new concept of in situ crosslinking from sulfonated polyimide (SPI) oligomers and triamine monomers. Chemical branching and crosslinking in SPI oligomers with 1,3,5‐tris(4‐aminophenoxy)benzene as a crosslinker gave the polymer membranes very good water stability and mechanical properties under an accelerated aging treatment in water at 130 °C, despite their high ion‐exchange capacity (2.2–2.6 mequiv g^?1). The resulting polymer electrolytes displayed high proton conductivities of 0.2–0.3 S cm^?1 at 120 °C in water and reasonably high conductivities of 0.02–0.03 S cm^?1 at 50% relative humidity. In a single H₂/O₂ fuel‐cell system at 90 °C, they exhibited high fuel‐cell performances comparable to those of Nafion 112. The B/C‐SPI membranes also displayed good performances in a direct methanol fuel cell with methanol concentrations as high as 50 wt % that were superior to those of Nafion 112. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3751–3762, 2006     

Highly proton conducting proton‐exchange membranes based on fluorinated poly(arylene ether ketone)s with octasulfonated segments

A new bisphenol monomer containing a pair of electron‐rich tetra‐arylmethane units was designed and synthesized. Based on this monomer, along with commercial 4,4′‐(hexafluoroisopropylidene)diphenol A and 4,4′‐difluorobenzophenone, a series of novel poly(arylene ether ketone)s containing octasulfonated segments of varying molar percentage (x) (6F‐SPAEK‐x) were successfully synthesized by polycondensation reactions, followed by sulfonation. Tough, flexible, and transparent membranes, exhibiting excellent thermal stabilities and mechanical properties were obtained by casting. 6F‐SPAEK‐x samples exhibited appropriate water uptake and swelling ratios at moderate ion exchange capacities (IECs) and excellent proton conductivities. The highest proton conductivity (215 mS cm⁻¹) is observed for hydrated 6F‐SPAEK‐15 (IEC = 1.68 meq g⁻¹) at 100 °C, which is more than 1.5 times that of Nafion 117. Furthermore, the 6F‐SPAEK‐10 membrane exhibited comparable proton conductivity (102 mS cm⁻¹) to that of Nafion 117 at 80 °C, with a relatively low IEC value (1.26 meq g⁻¹). Even under 30% relative humidity, the 6F‐SPAEK‐20 membrane (2.06 meq g⁻¹) showed adequate conductivity (2.1 mS cm⁻¹) compared with Nafion 117 (3.4 mS cm⁻¹). The excellent comprehensive properties of these membranes are attributed to well‐defined nanophase‐separated structures promoted by strong polarity differences between highly ionized and fluorinated hydrophobic segments. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 25–37     

Synthesis and properties of sulfonated poly(arylene ether) containing tetraphenylmethane moieties for proton‐exchange membrane

A novel sulfonated poly(arylene ether) containing tetraphenylmethane moieties was successfully synthesized by the sulfonation of a designed parent polymer using chlorosulfonic acid as sulfonation agent. The sulfonation took place only at the para position on the pendant phenyl rings because of the specially designed parent polymer. The sulfonation degree can be easily controlled by using different ratios of sulfonation agent to polymer repeating unit. The position and degree of sulfonation were characterized by ¹H NMR and elemental analysis. The sulfonated polymers are highly soluble in common organic solvents, such as dimethylsulfoxide, N,N′‐dimethylacetamide, dimethylformamide, ethylene glycol monomethyl ether, and can be readily cast into tough and smooth films from solutions. The films showed good thermal and hydrolysis stabilities. Moreover, Fenton's reagent test revealed that the membrane exhibited superior stability to oxidation. The proton conductivities of the films were determined to be equivalent with Nafion® 117 under same conditions. The new polymer with sulfonic acid function on pendent phenyl rings can be potentially used as a proton‐exchange membrane for polymer electrolyte membrane fuel cell. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6411–6418, 2005     

Synthesis and properties of novel polyimides from sulfonated binaphthalene dianhydride for proton exchange membranes

A sulfonated dianhydride monomer, 6,6′‐disulfonic‐4,4′‐binaphthyl‐1,1′,8,8′‐tetracarboxylic dianhydride (SBTDA), was successfully synthesized by direct sulfonation of the parent dianhydride, 4,4′‐binaphthyl‐1,1′,8,8′‐tetracarboxylic dianhydride (BTDA), using fuming sulfuric acid as the sulfonating reagent. A series of sulfonated homopolyimides were prepared from SBTDA and various common nonsulfonated diamines. The resulting polymer electrolytes, which contain ion conductivity sites on the deactivated positions of the aryl backbone rings, displayed high proton conductivities of 0.25–0.31 S cm^?1 at 80 °C. The oxidative stability test indicated that the attachment of the ? SO₃H groups onto the dianhydride units did not deteriorate the oxidative stability of the SPI membranes. The better membranes were achieved by the copolymerization of nonsulfonated diamine, SBTDA, and BTDA. Copolymer membrane synthesized from hexane‐1,6‐diamine, SBTDA, and BTDA displayed excellent water stability of more than 1000 h at 90 °C, while its proton conductivity was still at a high level (comparable to that of Nafion 117). Furthermore, the novel block copolymer ( II‐b ) displayed higher proton conductivity compared with the random one ( II‐r ) obviously, probably due to the slightly higher water uptake and better microphase separated morphology. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2820–2832, 2008     

Synthesis and Characterization of Phenolphthalein‐Containing Sulfonated Poly(arylene ether phosphine oxide)s by Direct Polycondensation for Proton Exchange Membrane

A series of novel phenolphthalein‐containing sulfonated poly(arylene ether phosphine oxide)s (sPAEPP) with various sulfonation degrees were synthesized by direct polycondensation. The structure of sPAEPP was confirmed by ¹H‐NMR, ¹³C‐NMR, and IR spectroscopy. The high‐molecular weight of these polymers was determined by gel permeation chromatography (GPC). The transparent, tough, and flexible membranes could be achieved by solution casting. The macroscopic properties and microstructure of the obtained membranes were investigated in detail. The results showed that these sPAEPP membranes displayed excellent properties in terms of swelling, proton conductivity, and methanol permeability. For example, sPAEPP‐100 membrane exhibited an appropriate water uptake of 33.1%, a swelling ratio of only 11.7% (lower than 20.1% of Nafion 117), a proton conductivity of 0.11 S cm^?1 (similar to that of Nafion 117) at 80 °C, and a methanol permeability of 4.82 × 10^?7 cm² s^?1. Meanwhile, it also presented outstanding oxidative stability. Atomic force microscope (AFM) micrographs showed that the hydrophilic domains of the sPAEPP‐100 membrane formed connected and narrow ionic channels, which contributed to its high proton conductivity and good dimensional stability. As a result, sPAEPP‐100 membrane displays excellent application prospect for fuel cells. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 1097–1104     

Novel sulfonated block copolymer containing pendant alkylsulfonic acids: Syntheses,unique morphologies,and applications in proton exchange membrane

In this article, we report the syntheses and characterizations of a series of novel block polyelectrolytes, poly(styrene‐block‐sulfonated hydroxystyrene) (PS‐b‐sPHS), containing pendant sulfonic acid groups attached to the backbone via propyl spacers in the sPHS domain. PS‐b‐sPHS with various compositions were synthesized via anionic polymerization and the following analogous chemistry to achieve accurate control of molecular weight (M_w), narrow polydispersity and high degree of sulfonation. Proton exchange membranes (PEMs) were prepared from PS‐b‐sPHS with sulfonic acids in either potassium salts or tetra‐alkylammonium salts via solvent casting and following treatments. Some unique morphologies, such as hallow channels and lamellar arrangement of strings of beads, were observed as a consequence of equilibrium between microphase separation and columbic interactions between polyelectrolytes. The transportation properties were found to closely relate to the morphologies of the PEMs. The combination of microphase separation of block polyelectrolytes and freedom of movement of pendent alkylsulfonic acids was demonstrated to effectively enhance the proton transport and suppress the methanol crossover for the PEMs, leading to the selectivity higher than Nafion 117 by five times at most. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Influence of the bisphenol structure on the direct synthesis of sulfonated poly(arylene ether) copolymers. I

New sulfonated poly(arylene ether sulfone) copolymers with high molecular weights were successfully synthesized with controlled degrees of disulfonation of up to 70 mol % via the direct copolymerization of sulfonated aromatic dihalides, aromatic dihalides, and one of four structurally distinct bisphenols. The disodium salts of the 3,3′‐disulfonated‐4,4′‐dichlorodiphenyl sulfone and 3,3′‐disulfonated‐4,4′‐difluorodiphenyl sulfone comonomers were synthesized via the sulfonation of 4,4′‐dichlorodiphenyl sulfone or 4,4′‐difluorodiphenyl sulfone with 30% fuming sulfuric acid at 110 °C. Four bisphenols (4,4′‐bisphenol A, 4,4′‐bisphenol AF, 4,4′‐biphenol, and hydroquinone) were investigated for the syntheses of novel copolymers with controlled degrees of sulfonation. The composition and incorporation of the sulfonated repeat unit into the copolymers were confirmed by ¹H NMR and Fourier transform infrared spectroscopy. Solubility tests on the sulfonated copolymers confirmed that no crosslinking and probably no branching occurred during the copolymerizations. Tough, ductile films were solvent‐cast that exhibited increased water absorption with increasing degrees of sulfonation. These copolymers are promising candidates for high temperature proton‐exchange membranes in fuel cells, which will be reported separately in part II of this series. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2264–2276, 2003     

Synthesis and characterization of thermally stable sulfonated polybenzimidazoles obtained from 3,3′‐disulfonyl‐4,4′‐dicarboxyldiphenylsulfone

A novel sulfonated aromatic diacid, 3,3′‐disulfonyl‐4,4′‐dicarboxyldiphenylsulfone (DSDCDPS), was successfully synthesized from 4,4′‐dimethyldiphenylsulfone by sulfonation and further oxidation. A series of sulfonated polybenzimidazoles (sPBI‐SS) with various sulfonation degrees was prepared from DSDCDPS, 4,4′‐sulfonyldibenzoic acid and 3,3′‐diaminobenzidine by solution copolycondensation in poly(phosphoric acid). The chemical structure of the resulting sPBI‐SS was confirmed by FTIR and ¹H NMR. The DSDCDPS‐based sPBI‐SS with the number‐average molecular weights of 32,000–55,000 were easy to dissolve in polar aprotic solvents such as DMF, DMSO, and DMAc, and could be cast into transparent, tough, and flexible membranes. The membranes presented good thermal stabilities (5% weight loss temperatures higher than 430 °C), and the thermal degradation activation energies of the sulfonic group of sPBI‐SS40 evaluated under N₂ by both Ozawa and Kissinger methods were 266.06 and 264.79 kJ/mol, respectively. The membranes also exhibited high storage moduli, glass transition temperatures (above 238 °C) and tensile strengths (～80 MPa), in addition to water uptakes (22.3–25.2%) and low swelling degrees (<14.0%). © 2005 Wiley Periodicals, Inc. J Polym Sci A: Polym Chem 43: 4363–4372, 2005     

Synthesis of sulfonated poly(diphenylacetylene)s with high CO2 permselectivity

High‐molecular‐weight poly[1‐phenyl‐2‐(4‐t‐butylphenyl)acetylene], poly[1‐phenyl‐2‐(4‐trimethylsilylphenyl) acetylene], and their copolymers were synthesized by the polymerization with TaCl₅–n‐Bu₄Sn. The obtained polymers were sulfonated by using acetyl sulfate to give sulfonated poly(diphenylacetylene)s with different degrees of substitution. The degrees of sulfonation of poly[1‐phenyl‐2‐(4‐t‐butylphenyl)acetylene] and copolymers were in the range of 0.57–0.85. When poly[1‐phenyl‐2‐(4‐trimethylsilylphenyl)acetylene] was sulfonated, the sulfonated poly(diphenylacetylene) with the highest degree of sulfonation was obtained among all the polymers in this study. Its degree of sulfonation was 1.55. All the sulfonated polymers exhibited high CO₂ permselectivity, and their CO₂/N₂ separation factor were over 31. The sulfonated poly(diphenylacetylene) with the highest degree of sulfonation showed the highest CO₂/N₂ separation factor of 75. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6463–6471, 2009     

Synthesis and characterization of sulfonated poly(phthalazinone ether ketone) for proton exchange membrane materials

As a novel class of proton exchange membrane materials for use in fuel cells, sulfonated poly(phthalazinone ether ketone)s (SPPEKs) were prepared by the modification of poly(phthalazinone ether ketone). Sulfonation reactions were conducted at room temperature with mixtures of 95–98% concentrated sulfuric acid and 27–33% fuming sulfuric acid with different acid ratios, and SPPEK was obtained with a degree of sulfonation (DS) in the desired range of 0.6–1.2. The presence of sulfonic acid groups in SPPEK was confirmed by Fourier transform infrared analysis, and the DS and structures were characterized by NMR. The introduction of sulfonic groups into the polymer chains increased the glass‐transition temperature above the decomposition temperature and also led to an overall decrease in the decomposition temperature. Membrane films were cast from SPPEK solutions in N,N‐dimethylacetamide. Water uptakes and swelling ratios of SPPEK membrane films increased with DS, and SPPEKs with DS > 1.23 were water‐soluble at 80 °C. Proton conductivity increased with DS and temperature up to 95 °C, reaching 10^?2S/cm. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 497–507, 2003     

Energy material - the role of silicotungstic acid and fly ash in sulfonated poly (ether sulfone) composites for PEMFC applications

The composite polymer electrolyte membranes were prepared from sulfonated poly (ether sulfone) (SPES), silicotungstic acid (STA) and fly ash (FA). Post sulfonation process was adopted to synthesize SPES using sulphuric and chlorosulfonic acid. The prepared electrolyte membranes were examined by water uptake capacity, swelling ratio, ion-exchange ability, proton conductivity, thermal stability and electrochemical performance for evaluating the pertinence of these membranes in fuel cell applications. As such the pristine membrane restricts with the proton conductivity of 0.042?S cm^?1 at 30?°C and 0.060?S cm^?1 at 90?°C while the polymer composite membrane, SP-STA-FA-10 reveals the maximum conductivity of 0.054?S cm^?1 at 30?°C and 0.073?S cm^?1 at 90?°C. It also exhibits good thermal stability than that of the pure membrane. The membrane electrode assemblies (MEAs) have been successfully developed from SPES as well as SP-STA-FA-10 membranes and their electrochemical performance were studied the wide range of current density. Herein, the composite membranes derived from SPES, STA and FA can be viable candidates for fuel cell applications.