Metallic single‐walled carbon nanotubes (m‐SWCNTs) with excellent conductivity and transparency are considered to be eminent electrode materials. However, it still remains a challenge to separate m‐SWCNTs by their diameters. As reported in this Letter, by effective purification treatment of SWCNTs, we succeeded in achieving diameter separation of m‐SWCNTs using gel column chromatography. TEM and Raman characterizations revealed that metal catalysts and amorphous carbon on tube surfaces were largely reduced, which contributed to the diameter separation of m‐SWCNTs.
An original approach is proposed to study the magnetic phase separation phenomenon. It is based on the registration of the noise‐like FMR Fine Structure (FMR FS) caused by the magnetic interparticle dipole–dipole interaction between spatially separated ferromagnetic regions. Data obtained for a La0.7Pb0.3MnO3 single crystal point to the existence of spatially separated ferromagnetic regions. It is shown that FMR FS of the La0.7Pb0.3MnO3 single crystal is temperature reversible and disappears at the maximum of magnetoresistance.
Dip‐coating of a colloidal suspension is investigated in situ with microbeam grazing incidence small‐angle X‐ray scattering. We focus on the real‐time monitoring of a vertical dip‐coating process yielding insights into structural changes during pattern formation of the thin film. With the selected configuration a fixed spot on the sample surface is probed and the structural information at the time the contact line passes this spot is obtained, hence revealing the structure at the vicinity of the flowing meniscus owing to the microfocused beam. After dip‐coating the morphology is analyzed with atomic force microscopy, yielding real space information about the arrangement of individual nanoparticles at the film surface.
In this Letter, a GaN‐based high‐power (HP) single‐chip (SC) large‐area LED with parallel and series network structure is fabricated. The optical characteristics of the HP‐SC LED is investigated. Driven at 600 mA, the optical output power of the HP‐SC LED chip is measured to be 9.7 W, corresponding to an EQE of 26.4%, which is 19.6% lower than that of the standard small LED cell due to both the lateral light‐extraction efficiency degradation and the self‐heating effect. A statistical analysis was carried out to investigate the yield of the fabricated HP‐SC LEDs, the experimental results agree with the theoretical calculations very well, validating the feasibility of this design on the production yield for the large‐area LEDs.
We present experimental and theoretical evidence of the role played by the spin–orbit coupling in the electronic structure of a pseudomorphic Au monolayer on Nb(001) substrate. The bands found with the help of the angle‐resolved ultraviolet photoelectron spectroscopy (ARUPS) are compared with those obtained from ab initio self‐consistent calculations by the VASP and WIEN2k codes. The slab calculations are performed including geometric relaxation and using both the generalized‐gradient (GGA) and local‐density (LDA) approximations for the exchange–correlation energy. The dispersions and energy positions of the calculated bands agree with the experimentally determined band structure only if the LDA is used and the spin–orbit coupling is included. Therefore, both the structure relaxation and spin–orbit coupling are essential in understanding the electronic structure of the Au/Nb(001) system.
Alkali‐free Cu(In,Ga)Se2(CIGS) absorbers grown on Mo‐coated alumina (Al2O3) substrates were doped with potassium (K) after CIGS growth by a potassium fluoride (KF) post‐deposition treatment (PDT). The addition of K to the absorber leads to a strong increase in cell efficiency from 10.0% for the K‐free cell to 14.2% for the K‐doped cell, mainly driven by an increase in the open‐circuit voltage Voc and the fill factor FF, and to an increase in the net charge carrier density. Hence K doping by KF‐PDT is comparable to doping with Na.
Steady‐state and time‐resolved photoluminescence of silicon nanoparticles dispersed in low‐polar liquids at above room temperature is studied. The roles of low‐polar liquids as well as mechanisms responsible for their temperature‐dependent photoluminescence are discussed. The thermal sensitivity of the photoluminescence is estimated and application of the nanoparticles as nanothermometers is proposed.
Write‐once–read‐many‐times memory (WORM) devices were fabricated using Ti/Au and Au as top contacts on ZnO thin films on Si. Electrical characterization shows that both types of WORM devices have large resistance OFF/ON ratio (R ratio), small resistance distribution range, long retention and good endurance. WORM devices with Au top contact have better performance of higher R ratio because of a larger work function of Au compared to Ti.
Interaction between negatively charged Nafion® and a positively charged polybenzimidazole‐decorated carbon nanotube leads to the formation of an ionic complex with high charge density for proton conduction, which can lead to an improvement in transport properties. Here we investigate the high‐temperature and low‐humidity proton conductivity of this nanocomposite membrane as a potential membrane for fuel cell applications.
The fabrication of titania nanostructures with hierarchical order of different structural levels is investigated. The nanostructures are prepared with a diblock‐copolymer assisted sol–gel process. By iterative spin‐coating of the solution onto silicon substrates a thin polymer‐nanocomposite film is deposited and transformed to purely anatase titania nanostructures via calcination. In total, this procedure is repeated three times on top of the substrate. The approach is monitored with grazing incidence small angle X‐ray scattering after each fabrication step. With scanning electron microscopy the final hierarchical structure is imaged. From the characterization different structural levels are clearly identified.
We report the fabrication procedure and the characterization of an Al0.3Ga0.7As solar cell containing high‐density GaAs strain‐free quantum dots grown by droplet epitaxy. The production of photocurrent when two sub‐bandgap energy photons are absorbed simultaneously is demonstrated. The high quality of the quantum dot/barrier pair, allowed by the high quality of nanostructured strain‐free materials, opens new opportunities for quantum dot based solar cells.
We report on solution‐processible polymer solar cells (PSCs) fabricated on a papery substrate using carton. Highly conductive PEDOT:PSS was used as a bottom anode and planarization layer, and a semi‐transparent top cathode was applied. This research could be an important approach to the development of all‐solution‐processible papery PSCs as well as paper electronics.
We have fabricated multi‐peak and chromaticity‐stable top‐emitting white organic light‐emitting diodes (TEWOLEDs) using single blue emitter. Besides the intrinsic emission of blue emitter, the additional emission can be well realized by simply adjusting the thickness of hole transporting layer (HTL), thus modifying the optical cavity length to obtain different resonant wavelengths. The detailed variation process for multi‐peak spectra with the increase of HTL thickness is studied, which provides a guidance for the design of microcavity TEWOLEDs.
The properties of transition‐metal (V, Cr, Mn, Fe, Co, Ni) δ‐doped ZnO are reported based on ab‐initio electronic structure calculations where the on‐site electronic correlations are included using the Hubbard parameters. The calculated electronic and magnetic properties are considerably altered with respect to usual band‐structure calculations. Most of the studied systems are found to be either half‐metals or ferromagnetic/antiferromagnetic semiconductors and thus can be employed in a variety of spintronic applications as spin‐filter materials.
We present metal wrap through (MWT) silicon solar cells with passivated surfaces based on a simplified device structure. This so‐called HIP‐MWT structure (high‐performance metal wrap through) does not exhibit an emitter on the rear side and therefore simplifies processing. The confirmed peak efficiency of the fabricated solar cells with an edge length of 125 mm, screen printed contacts and solder pads is 20.2%. To our knowledge, this is the highest value reported for large‐area p‐type silicon solar cells to date.
A new method for fabricating carbon nanotube‐conducting polymer (CNT‐CP) composite single nanowires is reported. The method developed is highly efficient, reliable, and economical because it obviates the time consuming process of template fabrication and the post‐synthesis task of positioning nanowires. Single nanowires with diameters of 50‐500 nm are fabricated between electrodes, self‐templated by dielectrophoresis and electropolymerization. Fabrication of an individually addressed nanowire array with cantilever electrodes on a microchip is demonstrated.
The metastability of the bixbyite‐ and corundum‐type In2O3 polymorphs up to 33 GPa (at room temperature) is shown. While compressed (in diamond anvil cells) and laser‐heated, both polymorphs undergo a phase transition to the Rh2O3‐II‐type structure (space group Pbcn, No. 60). The direct transition from bixbyite to Rh2O3‐II structure has not yet been observed for any other oxide.
In this Letter, a novel modified anodization was utilized to synthesize high‐aspect‐ratio, top‐open and ultraflat‐surface TiO2 nanotubes. The interruption of voltage during anodization leads to the formation of a double‐layered structure. Due to the weak mechanical connection between the upper and the underlying layer, the two parts can be easily detached. Compared with the conventional ultrasonication method to remove the clusters of nanotubes where rough surfaces resulted, this efficient and reliable strategy may facilitate further applications of TiO2 nanotubes in diverse conditions.
Light‐induced degradation of charge carrier lifetime was observed in indium‐doped silicon. After defect formation, an annealing step at 200 °C for 10 min deactivates the defect and the initial charge carrier lifetime is fully recovered. The observed time range of the defect kinetics is similar to the well known defect kinetics of the light‐induced degradation in boron‐doped samples. Differences between defect formation in boron‐ and indium‐doped silicon are detected and discussed. A new model based on an acceptor self‐interstitial ASi–Sii defect is proposed and established with experimental findings and existing ab‐initio simulations.
