Strain‐induced crystallization and mechanical properties of functionalized graphene sheet‐filled natural rubber

The effects of functionalized graphene sheets (FGSs) on the mechanical properties and strain‐induced crystallization of natural rubber (NR) are investigated. FGSs are predominantly single sheets of graphene with a lateral size of several hundreds of nanometers and a thickness of 1.5 nm. The effect of FGS and that of carbon black (CB) on the strain‐induced crystallization of NR is compared by coupled tensile tests and X‐ray diffraction experiments. Synchrotron X‐ray scattering enables simultaneous measurements of stress and crystallization of NR in real time during sample stretching. The onset of crystallization occurs at significantly lower strains for FGS‐filled NR samples compared with CB‐filled NR, even at low loadings. Neat‐NR exhibits strain‐induced crystallization around a strain of 2.25, while incorporation of 1 and 4 wt % FGS shifts the crystallization to strains of 1.25 and 0.75, respectively. In contrast, loadings of 16 wt % CB do not significantly shift the critical strain for crystallization. Two‐dimensional (2D) wide angle X‐ray scattering patterns show minor polymer chain alignment during stretching, in accord with previous results for NR. Small angle X‐ray scattering shows that FGS is aligned in the stretching direction, whereas CB does not show alignment or anisotropy. The mechanical properties of filled NR samples are investigated using cyclic tensile and dynamic mechanical measurements above and below the glass transition of NR. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Fly ash particles and precipitated silica as fillers in NR/CR vulcanizates under thermal and thermal‐oil ageing

The loading effect of precipitated silica (PSi) and fly ash‐based silica (FASi) on mechanical properties of natural rubber/chloroprene (NR/CR) under thermal and thermal‐oil ageing was investigated with variation in NR content in the NR/CR blends. The selected results were compared with vulcanized NR/nitrile rubber (NR/NBR) blends. The cure time of CR vulcanizate was found to decrease with increasing NR content, but increased with silica fillers. The Mooney viscosity for CR vulcanizates reduced with increasing NR content. The addition of NR had no effect on tensile modulus and tensile strength for the FASi filled NR/CR, but the opposite trend was observed for the PSi filled NR/CR. The post‐curing effect was more significant in PSi filled NR/CR than in FASi filled NR/CR. The tensile strength of the NR/CR vulcanizates was slightly reduced after thermal ageing especially at high NR content, more extreme reduction being found by thermal‐oil ageing. The elongation at break of NR/CR with both silica fillers ranged from 400 to 900%. The hardness results were similar to the tensile modulus. The addition of PSi in NR/CR considerably increased the tear strength, but less pronounced effect was found for FASi. The resilience properties of NR/CR tended to decrease with increasing silica content. The compression set became poorer when NR content was increased. The PSi showed higher improvement in compression set than the FASi. The effects of silica and ageing on the mechanical properties for NR/CR vulcanizates were similar to those for NR/NBR vulcanizates. Copyright © 2009 John Wiley & Sons, Ltd.     

Improved resistance to crack growth of natural rubber by the inclusion of nanoclay

The effect of nanoclay on the fatigue crack growth behavior was investigated. Fatigue tests were carried out on edge notched specimens under cyclic tension loadings. A power–law dependency between crack growth rate and tearing energy was obtained. Natural rubber (NR) filled with 5 phr organically modified montmorillonite (OMMT) possessed the lowest value of the exponent, b, and the smallest crack growth rate at a given tearing energy, denoting the strongest resistance to crack growth. Strain‐induced crystallization was probed by synchrotron WAXD experiments, showing earliest occurrence and strongest ability of crystallization in NR with 5 phr OMMT due to the better exfoliation and orientation of clay layers. The study on the viscoelastic property by dynamic mechanical analysis indicated that NR filled with 10 phr OMMT had the largest contribution to tearing energy attributed to the viscoelastic dissipation in the viscoelastic region in front of the crack tip. This revealed that the strain‐induced crystallization played a more important role in the crack growth resistance than the viscoelastic dissipation for clay filled rubber. Copyright © 2010 John Wiley & Sons, Ltd.     

Reinforcement of compatibilized NR/NBR blends by fly ash particles and precipitated silica

Effects of precipitated silica (PSi) and silica from fly ash (FA) particles (FASi) on the cure and mechanical properties before and after thermal and oil aging of natural rubber (NR) and acrylonitrile–butadiene rubber (NBR) blends with and without chloroprene rubber (CR) or epoxidized NR (ENR) as a compatibilizer have been reported in this paper. The experimental results suggested that the scorch and cure times decreased with the addition of silica and the compound viscosity increased on increasing the silica content. The mechanical properties for PSi filled NR/NBR vulcanizates were greater than those for FASi filled NR/NBR vulcanizates in all cases. The PSi could be used for reinforcing the NR/NBR vulcanizates while the silica from FA was regarded as a semi‐reinforcing and/or extending filler. The incorporation of CR or ENR enhanced the mechanical properties of the NR/NBR vulcanizates, the ENR being more effective and compatible with the blend. The mechanical properties of the NR/NBR vulcanizates were improved by post‐curing effect from thermal aging but deteriorated by the oil aging. Copyright © 2008 John Wiley & Sons, Ltd.     

Microbial desulfurization of SBR ground rubber by Sphingomonas sp. and its utilization as filler in NR compounds

Microbial desulfurization of waste tyre rubber has been investigated with great efforts since 1990s, because waste rubber has created serious ecological and environmental problems. A microbial desulfurization technique for SBR ground rubber has been developed by a novel sulfur‐oxidizing bacterium Sphingomonas sp. The adaptability of Sphingomonas sp. with SBR ground rubber was tested with the amounts of SBR ground rubber varying from 0.5 to 4% g/l. The sol fraction of desulfurized SBR ground rubber increased 70%, compared with SBR ground rubber without desulfurization. Fourier transform infrared spectroscopy‐attenuated total reflectance (FTIR‐ATR) spectrum and X‐ray photoelectron spectroscopy (XPS) analysis of the desulfurized surface of vulcanized SBR flakes revealed that not only the oxidation of crosslinked S? S and S? C bonds, but also the rupture of C?C double bonds had happened to SBR vulcanizates during microbial desulfurization. The cure characteristics, such as scorch time and optimum cure time of natural rubber (NR) vulcanizates filled, were found to decrease with increasing contents of desulfurized SBR ground rubber, due to some reactive groups on its surface. NR vulcanizates filled with desulfurized SBR ground rubber had lower crosslink density and hardness, higher tensile strength and elongation at break, compared with those filled with SBR ground rubber of the same amount. Dynamic mechanical properties indicated that there were better crosslink distribution and stronger interfacial bonding between NR matrix and desulfurized SBR ground rubber. Scanning electron microscope (SEM) photographs showed that the fracture surfaces of NR vulcanizates filled with desulfurized SBR ground rubber had more smooth morphologies. Copyright © 2010 John Wiley & Sons, Ltd.     

Impacts of filler covalent and non‐covalent modification on the network structure and mechanical properties of carbon–silica dual phase filler/natural rubber

The carbon–silica dual phase filler (CSDPF) was modified by bis (3‐triethoxy‐silylpropyl) tetrasulphane (Si69) and 1‐allyl‐3‐methyl‐imidazolium chloride (AMI), respectively. The natural rubber (NR) vulcanizates filled with modified CSDPF were fabricated through mechanical mixing followed by a high‐temperature cure process. The impacts of filler surface modification on the curing characters, crosslinked junctions, network structure, and mechanical properties of NR vulcanizates were investigated. The results showed that the Si69 interacted with CSDPF through covalent bond, while the interaction between AMI and CSDPF was hydrogen bond. Both modifications increased the cure rate of CSDPF/NR compounds as well as the crosslinked degree, compared with those of pristine CSDPF/NR compound. The modifications improved the dispersion of CSDPF in NR matrix. The covalent modification by Si69 caused a limited movement of NR chains in the CSDPF surface, which contributed to a greater tensile modulus of Si69‐modified CSDPF/NR. However, the higher content of mono‐sulfidic crosslink and the poorer content of strain‐induced crystallization in the NR matrix led to a slight increase of tensile strength and tear strength of Si69‐modified CSDPF/NR, compared with those of CSDPF/NR. The tensile modulus of AMI‐modified CSDPF/NR had a lower value due to a faster polymer chain motion on the CSDPF surface. However, the tensile and tear strength of AMI‐modified CSDPF/NR increased significantly because of the increase of mono‐sulfidic crosslink, strain‐induced crystallization, and the existed hydrogen bond between CSDPF and NR. Copyright © 2015 John Wiley & Sons, Ltd.     

Novel biphasic structured composite prepared by in situ silica filling in natural rubber latex

The sol‐gel reaction of tetraethoxysilane in natural rubber (NR) latex was conducted to produce in situ silica‐filled NR latex, followed by adding sulfur cross‐linking reagents to the latex in a liquid state. The latex was cast and subjected to sulfur curing to result in a unique morphology in the NR composite of a flexible film form. The contents of in situ silica filling were controlled up to 35 parts per one hundred rubber by weight. The silica was locally dispersed around rubber particles to give a filler network. This characteristic morphology brought about the composite of good dynamic mechanical properties. Synchrotron X‐ray absorption near‐edge structure spectroscopy suggested that the sulfidic linkages of the sulfur cross‐linked composites were polysulfidic, S_x (x ≥ 2), and a fraction of shorter polysulfidic linkages became larger with the increase of in situ silica. The present observations will be of use for developing a novel in situ silica‐filled NR composite prepared in NR latex via liquid‐phase soft processing. Copyright © 2011 John Wiley & Sons, Ltd.     

CSF纳米炭黑硫化橡胶的性能

天然橡胶;丁苯橡胶;丁腈橡胶;硫化;气密性;导电性;CSF纳米炭黑硫化橡胶的性能     

Effects of vulcanization accelerator functionalized graphene on the co-vulcanization kinetics and mechanical strength of NR/SBR blends

Rubber blends are widely used for combining the advantages of individual rubber component. However, to date, how to determine and distinguish the vulcanization kinetics for each single rubber phase in rubber blends during the co-vulcanization process are still a challenge. Herein, high resolution pyrolysis gas chromatography-mass spectrometry (PyGC-MS) was employed for the first time to investigate the vulcanization kinetics of natural rubber (NR) and styrene-butadiene rubber (SBR) in their blends filled with graphene. It is shown that the crosslinking rate of NR chains (k_NR) was much lower than that of SBR chains (k_SBR) in the unfilled blends and blends with untreated graphene. Interestingly, the gap between k_SBR and k_NR was narrowed effectively in the blends with vulcanization accelerator grafted graphene, showing a better co-vulcanization of NR and SBR. In addition, the vulcanization accelerator grafted graphene was uniformly dispersed in rubber matrix and endowed rubber blends with higher mechanical strength and thermal conductivity did the untreated graphene.     

Effect of silane coupling agent on the polymer‐filler interaction and mechanical properties of silica‐filled NR

The effects of filler loading and a new silane coupling agent 3‐octanoylthio‐1‐ propyltriethoxysilane (NXT silane) on the polymer‐filler interaction and mechanical properties of silica‐filled and carbon black‐filled natural rubber (NR) compounds were studied. Silica (high dispersion silica7000GR, VN2, and VN3) and carbon black (N330) were used as the fillers, and the loading range was from 0 to 50 phr. The loading of NXT silane was from 0 to 6 phr. Experimental results show that the maximum and minimum torques of silica and carbon black‐filled NR increase with increasing filler loading. With increasing filler loading, the scorch time and optimum cure time decrease for carbon black‐filled NR, but increase for silica‐filled NR. The minimum torque, scorch time, and optimum cure time decrease because of the presence of NXT silane. For the carbon black and silica‐filled NR, the tensile strength and elongation at break have maximum values, but the hardness, M300, M100, and tear strength keep increasing with filler loading. The mechanical properties of silica‐filled NR were improved in the presence of NXT silane. With increasing filler loading, the storage modulus of filled NR increases, but the loss factor decreases. Carbon black shows the strongest polymer‐filler interaction, followed by VN3, 7000GR, and VN2. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 573–584, 2005     

Preparation and properties of natural rubber composites reinforced with pretreated carbon nanotubes

In order to achieve dramatic improvements in the performance of rubber materials, the development of carbon nanotube (CNT)‐reinforced rubber composites was attempted. The CNT/natural rubber (NR) nanocomposite was prepared through solvent mixing on the basis of pretreatment of CNTs. Thermal properties, vulcanization characteristics, and physical and mechanical properties of the CNT/NR nanocomposites were characterized in contrast to the carbon black (CB)/NR composite. Through the addition of the CNTs treated using acid bath followed by ball milling with HRH (hydrated silica, resorcinol, and hexamethylene tetramine) bonding systems, the crystallization melting peak in differential scanning calorimetry (DSC) curves of NR weakened and the curing rate of NR slightly decreased. Meanwhile, the over‐curing reversion of CNT/NR nanocomposites was alleviated. The dispersion of the treated CNTs in the rubber matrix and interfacial bonding between them were rather good. The mechanical properties of the CNT‐reinforced NR showed a considerable increase compared to the neat NR and traditional CB/NR composite. At the same time, the CNT/NR nanocomposites exhibited better rebound resilience and dynamic compression properties. The storage modulus of the CNT/NR nanocomposites greatly exceeds that of neat NR and CB/NR composites under all temperature regions. The thermal stability of NR was also obviously improved with the addition of the treated CNTs. Copyright © 2008 John Wiley & Sons, Ltd.     

Effect of fly ash silica and precipitated silica fillers on the viscosity,cure, and viscoelastic properties of natural rubber

The viscosity, cure properties, storage, and loss moduli and tan δ of natural rubber (NR) filled with the same amounts of precipitated silica (PSi) and fly ash silica (FASi) fillers were measured. The fillers were treated with bis[3‐triethoxysilylpropyl‐]tetrasulfide (TESPT), or, used in the rubber untreated. TESPT is a sulfur‐containing bi‐functional organosilane that chemically adheres silica to rubber and also prevents silica from interfering with the reaction mechanism of sulfur cure. The dispersion of PSi and FASi in the rubber was investigated using scanning electron microscope (SEM). The effects of silica type and loading and surface treatment on the aforementioned properties were of interest. The SEM results showed that the FASi particles were larger in size and had a wider particle size distribution when compared with the PSi particles. The viscosity of the compounds decreased progressively with mixing time, and the compounds with FASi had a lower viscosity than those filled with PSi. The treatment with Si69 had no beneficial effect on the dispersion of the fillers in the rubber matrix. At low temperatures, the type and loading of the filler had no effect on the storage and loss moduli of the compounds, but the effect was more pronounced at high temperatures. There was also evidence from the tan δ and glass transition temperature (T_g) measurements that some limited interaction between the filler particles and rubber had occurred because of TESPT. Copyright © 2008 John Wiley & Sons, Ltd.     

Influence of gel content on the physical properties of unfilled and carbon black filled natural rubber vulcanizates

Recently, gel content has been considered as a standard property for evaluating commercial grade natural rubber (NR). In this study, NR containing various amounts of gel was prepared by accelerated storage hardening as a model to clarify the influence of gel content on the physical properties of both unfilled and carbon black filled vulcanizates. Furthermore, the NR samples were investigated to determine the effect of gel fraction on Mooney viscosity and the structure of the gel after mastication. The results revealed that Mooney viscosity was related to the percentage of gel fraction that has been proven to be the result of interactions between proteins and phospholipids at chain ends. After mastication, although the gel fraction of NR can be decomposed to ∼0% w/w, the interactions of proteins and phospholipids at the chain ends still existed, corresponding to the gel content of the raw rubber. In the case of unfilled vulcanizates, the gel content showed no effect on cure characteristics, crosslink density and ultimate tensile strength, whereas the upturn of stress occurred at a smaller strain when the gel content increased. However, in the case of carbon black filled vulcanizates, the gel content played a dominant role in the carbon black dispersion, which was poorer when gel content increased, contributing to a decrease of crosslink density and ultimate tensile strength.     

Influences of different dimensional carbon-based nanofillers on fracture and fatigue resistance of natural rubber composites

The dimensions of reinforcing filler is a key factor in influencing the fracture and fatigue of rubbers. Here, the fracture and fatigue resistance of natural rubber (NR) filled with different dimensional carbon-based fillers including zero-dimensional spherical carbon black (CB), one-dimensional fibrous carbon nanotubes (CNTs) and two-dimensional planar graphene oxide (GO) were explored. To obtain equal hardness, a control indicator in the rubber industry, the amounts of CB, CNTs, and GO were 10.7 vol%, 1.2 vol%, and 1.6 vol%, respectively. J-integral and dynamic fatigue tests revealed that NR filled with CB exhibited the best quasi-static fracture resistance and dynamic crack growth resistance. The much higher hysteresis loss of NR filled with CNTs weakened its fatigue resistance. The planar GO played a limited role in preventing crack growth. Furthermore, digital image correlation revealed that NR filled with CB had the highest strain amplification level and area at the crack tip, which dissipated the most local input energy and then improved the fracture and fatigue performance.     

Effect of sol–gel derived in situ silica on the morphology and mechanical behavior of natural rubber and acrylonitrile butadiene rubber blends

Silica particles were generated and grown in situ by sol–gel method into rubber blends comprised of natural rubber (NR) and acrylonitrile butadiene rubber (NBR) at various blend ratios. Silica formed into rubber matrix was amorphous in nature. Amount of in situ silica increased with increase in natural rubber proportion in the blends during the sol–gel process. Morphology studies showed that the generated in situ silica were nanoparticles of different shapes and sizes mostly grown into the NR phase of the blends. In situ silica filled NR/NBR blend composites showed improvement in the mechanical and dynamic mechanical behaviors in comparison to those of the unfilled and externally filled NR/NBR blend composites. For the NR/NBR blend at 40/60 composition, in particular, the improvement was appreciable where size and dispersion of the silica particles into the rubber matrix were found to be more uniform. Dynamic mechanical analysis revealed a strong rubber–in situ silica interaction as indicated by a positive shift of the glass transition temperature of both the rubber phases in the blends.     

Nano‐Structural Observation of in situ Silica in Natural Rubber Matrix by Three Dimensional Transmission Electron Microscopy

Summary: Three dimensional (3D) nanostructures of particulate silicas in natural rubber (NR) were observed for the first time by use of 3D transmission electron microscopy (3D‐TEM) combined with electron tomography. The method enabled us to visualize and evaluate structural characteristics in 3D space, such as the size and the volume of in situ silica generated in the NR matrix by the sol‐gel reaction of tetraethoxysilane, at nanometer scale resolution.

The reconstructed mass density view of the silica in an in situ silica‐filled natural rubber vulcanizate, as determined by 3D‐TEM.     

The use of zinc dimethacrylate functionalized graphene as a reinforcement in rubber composites

Zinc dimethacrylate functionalized graphene (Z‐GE), as reinforcing nanofiller for natural rubber (NR), was synthesized by liquid‐phase exfoliation and in situ method. The morphology and structure of Z‐GE were characterized to confirm the exfoliation and functionalization of GE. The NR/Z‐GE composites were prepared and investigated by mechanical analysis, crosslinked network analysis and the analysis of thermal conductivity. The results showed that the tensile strength, tear strength and modulus at 300% strain of NR/Z‐GE‐20 composites (contents 1.400 phr GE) were increased by 142%, 76% and 231% as compared with the pure NR, respectively. And the thermal conductivity of NR/Z‐GE‐30 composites is enhanced by 39% as that of the pure NR. This significant improvement is attributed to the formation of covalent crosslinked network and ionic crosslinked network and efficient interfacial interaction between GE and NR matrix. This method provides a new insight into the fabrication of multifunctional GE composites and enlarges its potential applications in high performance GE‐based rubber composites. Copyright © 2015 John Wiley & Sons, Ltd.     

Surface Modification of Rice Husk Ash by Ethanol-assisted Milling to Reinforce the Properties of Natural Rubber/Butadiene Rubber Composites

Rice husk ash(RHA), obtained by pyrolysis of rice husks, can be used as a potential reinforcing filler for rubber composites. In this work, ball milling in ethanol(ethanol-assisted milling) was used to hydroxylate the surface of RHA, promoting the graft modification of bis-(γ-triethoxysilylpropyl)-tetrasulfide(Si69). The obtained modified RHA(RHA-EM-Si69) was filled into the natural rubber/butadiene rubber(NR/BR) composites, and the filler-rubber interactions were enhanced. In consequence, RHA-EM-Si69 filled NR/BR composites showed overall improvement in the mechanical properties compared with RHA filled NR/BR composites. The tear strength increased from 13.37 kN/m to 34.71 kN/m, and the tensile strength increased from 1.84 MPa to 7.75 MPa. Carbon black(N774) was also used for comparison under the same conditions. This method provides a potential for promoting the value of RHA in rubber industry.     

A theory of green strength in polyisoprene

It is shown that, at ?25°C, natural rubber (NR) crystallizes more readily than synthetic polyisoprene (IR), the long induction period for nucleation in IR in particular being dependent on the carbon black loading. Both elastomers form bound rubber with carbon black but not with nonreinforcing fillers such as CaCO₃ and glass powder. At room temperature, in the presence of carbon black, NR has good green strength but not IR, while neither rubber has good green strength with nonreinforcing fillers. However, at 0°C CaCO₃ filled NR too has good green strength. A theory is proposed to account for the good green strenth characteristics found with certain compounds. In the model rubber molecules, already bound to the carbon black surface, are linked together, at low strains, via stress-induced crystal lamellae, giving a three-dimensional network in the compound. Such crystal lamellae are known to grow at right angles to the direction of strain from row nuclei formed at low strains. The coherence provided by the network permits the formation, at higher strains, of stress-induced crystals in which polymer chains are now aligned in the direction of strain. This leads to an upturn in the stress–strain curve. In the absence of either bound rubber or of crystal lamellae, a long range network structure cannot form and extension of the sample continues at constant stress.