The influence of bending on the performance of flexible carbon black/polymer composite gas sensors

The performance of electronics on flexible substrates suffers under substrate bending leading to reduced device performance. In this article, we highlighted the influence of bending strain on a conductive polymer composite gas sensor and developed a model to investigate the influence of strain. We evaluated the strain influence on the resistance of a gas sensor with respect to sensitivity, filler content, cyclic loading, and electrode orientation. The sensitivity of gas sensors increased with decreasing tensile bending radii. The influence of strain was dominant for gas sensors with less carbon black concentration. Cyclic bending tests showed a decrease of sensor resistance versus time and a plastic deformation. A sensor geometry orientations effect to reduce the sensitivity to bending strain was achieved by aligning the electrode fingers parallel to the strain. A model was successfully implemented to simulate strain influences inside the polymer incorporating the Poisson ratio. We suggest a concept to achieve a strain insensitive gas sensor by creating an orientation between single particles inside the composite. Implementing this results into existing gas sensors will improve the measurement quality and reliability of sensors on flexible substrates. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Flexible conducting polymer transistors with supercapacitor function

Planar organic electrochemical transistors (OECTs) using PEDOT:PSS as the channel material and nanostructured carbon (nsC) as the gate electrode material and poly(sodium 4‐styrenesulfonate (PSSNa) gel as the electrolyte were fabricated on flexible polyethylene terephthalate (Mylar^®) substrates. The nsC was deposited at room‐temperature by supersonic cluster beam deposition (SCBD). Interestingly, the OECT acts as a hybrid supercapacitor (to give a device that we indicate as transcap). The energy storage ability of transcaps has been studied with two cell configurations: one featuring PEDOT:PSS as the positive electrode and nsC as the negative electrode and another configuration with reversed electrode polarity. Potentiostatic charge/discharge studies show that both supercapacitors show good performance in terms of voltage retention, in particular, when PEDOT:PSS is used as the positive electrode. Galvanostatic charge–discharge characteristics show typical symmetric triangular shape, indicating a nearly ideal capacitive behavior with a high columbic efficiency (close to 100%). © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 96–103     

Spatial control of p-n junction in an organic light-emitting electrochemical transistor

Low-voltage-operating organic electrochemical light-emitting cells (LECs) and transistors (OECTs) can be realized in robust device architectures, thus enabling easy manufacturing of light sources using printing tools. In an LEC, the p-n junction, located within the organic semiconductor channel, constitutes the active light-emitting element. It is established and fixated through electrochemical p- and n-doping, which are governed by charge injection from the anode and cathode, respectively. In an OECT, the electrochemical doping level along the organic semiconducting channel is controlled via the gate electrode. Here we report the merger of these two devices: the light-emitting electrochemical transistor, in which the location of the emitting p-n junction and the current level between the anode and cathode are modulated via a gate electrode. Light emission occurs at 4 V, and the emission zone can be repeatedly moved back and forth within an interelectrode gap of 500 μm by application of a 4 V gate bias. In transistor operation, the estimated on/off ratio ranges from 10 to 100 with a gate threshold voltage of -2.3 V and transconductance value between 1.4 and 3 μS. This device structure opens for new experiments tunable light sources and LECs with added electronic functionality.     

A glucose sensor via stable immobilization of the GOx enzyme on an organic transistor using a polymer brush

Recently, there has been significant research in the area of organic electrochemical transistors (OECTs) because of their superior aptitude of chemical and biological sensing. Here it is shown for the first time the incorporation of polymer brushes to a transistor. Polymer brushes were chosen for their biocompatible properties and their ability to covalently tether enzymes and other biomolecules to different surfaces. OECTs were fabricated from the conducting polymer poly(3,4-ethylenedioxythiophene) doped with poly(styrene sulfonate), PEDOT:PSS, and polymerized from the surface a mixed polymer brush of poly(glycidyl methacrylate) and poly(2-hydroxyethyl methacrylate). The brushes were functionalized with glucose oxidase and measured in terms of electrical performance and long-term stability. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 372–377     

Highly Sensitive and Selective Fluorometric/Electrochemical Dual‐Channel Sensors for TNT and DNT Explosives

A novel electro‐active compound, TCAC , is synthesized and its electrochemical polymerized film is used to detect 2,4,6‐trinitrotoluene (TNT) and 2,4‐dinitrotoluene (DNT) explosives through a fluorometric/electrochemical dual‐channel sensor with high sensitivity and selectivity. In particular, the electrochemical sensor for the analysis of TNT had an enhanced sensitivity of 0.5 μM . The detection limit of the sensor was calculated to be 15 nM .     

Electrochemiluminescence biosensor for Ramos cells based on a nanostructured conducting polymer composite material (PICA‐MWNTs)

A novel nanostructured conducting polymer (PICA‐MWNTs) is easily prepared by direct electrodeposition of indole‐6‐carboxylic acid (ICA) and carboxylic groups ended multiwalled carbon nanotubes (MWNTs) in acetonitrile in one step. The resulting PICA‐MWNTs composites with larger specific surface area and quite a few functionalized carboxylic acid groups are naturally integrated as a continuous uniform film on the electrode. CdSe quantum dots electrochemiluminescence biosensor with high sensitivity for detection of Ramos cells is fabricated based on PICA‐MWNTs. Coupled with nanoparticle‐amplification technnique, this sensor shows high sensitivity and good selectivity for Ramos cells with a low detection limit of 390 cells mL^?1. This result provides an avenue for a simple and sensitive approach for detection of Ramos cells, which may have great potential in clinical applications. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2385–2392     

Graphene Paper Decorated with a 2D Array of Dendritic Platinum Nanoparticles for Ultrasensitive Electrochemical Detection of Dopamine Secreted by Live Cells

To circumvent the bottlenecks of non‐flexibility, low sensitivity, and narrow workable detection range of conventional biosensors for biological molecule detection (e.g., dopamine (DA) secreted by living cells), a new hybrid flexible electrochemical biosensor has been created by decorating closely packed dendritic Pt nanoparticles (NPs) on freestanding graphene paper. This innovative structural integration of ultrathin graphene paper and uniform 2D arrays of dendritic NPs by tailored wet chemical synthesis has been achieved by a modular strategy through a facile and delicately controlled oil–water interfacial assembly method, whereby the uniform distribution of catalytic dendritic NPs on the graphene paper is maximized. In this way, the performance is improved by several orders of magnitude. The developed hybrid electrode shows a high sensitivity of 2 μA cm^?2 μm ^?1, up to about 33 times higher than those of conventional sensors, a low detection limit of 5 nm, and a wide linear range of 87 nm to 100 μm . These combined features enable the ultrasensitive detection of DA released from pheochromocytoma (PC 12) cells. The unique features of this flexible sensor can be attributed to the well‐tailored uniform 2D array of dendritic Pt NPs and the modular electrode assembly at the oil–water interface. Its excellent performance holds much promise for the future development of optimized flexible electrochemical sensors for a diverse range of electroactive molecules to better serve society.     

Effect of (L:D) Aspect Ratio on Single Polypyrrole Nanowire FET Device

Effect of different aspect ratio (length to diameter ratio, L:D) on single polypyrrole (Ppy) nanowire based field effect transistor (FET) sensor for real time pH monitoring was studied. Ppy nanowires with diameters of ~60, ~80 and ~200 nm were synthesized using electrochemical deposition inside anodized aluminium oxide (AAO) template and were assembled using AC dielectrophoretic alignment followed by maskless anchoring on a pair of gold electrodes separated with different gap lengths. Microfabricated gold electrode patterns with gap size between 1 - 4 μm were developed by means of MEMS technique (photolithography). Using field effect transistor geometry with pair of microfabricated gold contact electrodes serving as a source and a drain, and a platinum (Pt) mesh (anchored in a microfluidic channel) was used as a gate electrode. When effect of different aspect ratio of the nanowire were compared, higher sensitivity was recorded for higher aspect ratio. The sensitivity was further improved by modulating the gate potential. These FET sensors based on single polypyrrole nanowire exhibited excellent and tunable sensitivity towards pH variations.     

Multichannel detection using transmissive diffraction grating sensor

We report a novel transmissive diffraction grating pH sensor made of pH‐sensitive hydrogel. The sensor provides inherently multichannels for a flexible selection of different detection ranges, without involving any additional tuning mechanisms or using multiple sensing elements. Each transmitted diffraction order from the hydrogel grating forms an individual detection channel dedicated to a specific pH range. This unique feature is achieved, simply by enabling hydrogel ridges of the grating to swell effectively in lateral directions, while inhibiting the ridges from swelling in vertical direction and keeping grating period unchanged. Thus by looking at different diffraction orders and measuring their intensity ratio, it is possible to achieve tunable dynamic detection range. Besides, this approach can lead to a high‐sensitivity sensor for detecting subtle pH variations in a narrow pH range near the volume‐phase transition point of hydrogel, with the resolution at the level of 10^?3 pH units. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Bioinspired polymer functionalized with a diiron carbonyl model complex and its assembly onto the surface of a gold electrode via “click” chemistry

A complex pendant with two ethynyl groups, [Fe₂(μ‐SCH₂CCH)₂(CO)₆] ( 2 ), as a model of the diiron subunit of [FeFe]‐hydrogenase was polymerized and the {Fe₂(CO)₆} core was successfully incorporated into the polymer matrix. The polymer was characterized by a variety of spectroscopic techniques, TGA, FTIR, SEM, TEM, and NMR. The resultant polymer was immobilized via “click” chemistry using its terminal C?CH bond onto the surface of a gold electrode, which was premodified with azidothiol by self‐assembled monolayer (SAM). The assembled electrode showed electrochemical responses. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2410–2417, 2010     

Construction of a novel electrochemical sensor based on molecularly imprinted polymers for the selective determination of chlorpyrifos in real samples

We present a novel electrochemical sensor based on an electrode modified with molecularly imprinted polymers for the detection of chlorpyrifos. The modified electrode was constructed by the synthesis of molecularly imprinted polymers by a precipitation method then coated on a glassy carbon electrode. The surface morphology of the modified electrode was characterized by using field‐emission scanning electron microscopy and transmission electron microscopy. The performance of the imprinted sensor was thoroughly investigated by using cyclic voltammetry and differential pulse voltammetry. The imprinted electrochemical sensor displayed high repeatability, stability, and selectivity towards the template molecules. Under the optimal experimental conditions, the peak current response of the imprinted electrochemical sensor was linearly related to the concentration of chlorpyrifos over the range 1 × 10⁻¹⁰–1 × 10⁻⁵ mol/L with a limit of detection of 4.08 × 10⁻⁹ mol/L (signal‐to‐noise ratio = 3). Furthermore, the proposed molecularly imprinted electrochemical sensor was applied to the determination of chlorpyrifos in the complicated matrixes of real samples with satisfactory results. Therefore, the molecularly imprinted polymers based electrochemical sensor might provide a highly selective, rapid, and cost‐effective method for chlorpyrifos determination and related analysis.     

Molecular design strategies for high-performance organic electrochemical transistors

Organic electrochemical transistors (OECTs) utilize ion flow from the electrolyte to modulate the electrical conductivity of the whole bulk organic semiconductor channel. With the characteristic of mixed ionic-electronic conducting in the entire volume, OECTs exhibit high transconductance and act as good transducers, particularly in bioelectronics. To gain high-performance OECTs, developing novel high-performance polymeric semiconductors is important. In this article, operation principles, performance evaluations, and polymerization methods are first discussed. We then analyze the molecular design strategies for high-performance OECT materials and highlight the characteristics and effects of backbone design and side chain engineering. Finally, we discuss some neglected and unsolved issues and provide an outlook for the OECTs research and development.     

Development of an Electrochemical Sensor Based on Covalent Molecular Imprinting for Selective Determination of Bisphenol‐A

In this study, an electrochemical sensor was developed and used for selective determination of bisfenol‐A (BPA) by integrating sol‐gel technique and multi‐walled carbon nanotubes (MWCNTs) modified paste electrode. BPA bounded by covalently to isocyanatopropyl‐triethoxy silane (ICPTS) was synthesized as a new precursor (BPA‐ICPTS) and then BPA‐imprinted polymer (BPA‐IP) sol‐gel was prepared by using tetramethoxysilane (TMOS) and BPA‐ICPTS. Non‐imprinted polymer (NIP) sol‐gel was obtained by using TMOS and (3‐Aminopropyl) triethoxysilane. Both BPA‐IP and NIP sol‐gels were characterized by nitrogen adsorption‐desorption analysis, FTIR, SEM, particle size analyzer and optical microscope. Carbon paste sensor electrode was fabricated by mixing the newly synthesized BPA‐IP with MWCNTs, graphite powder and paraffin oil. The electrochemical characterization of the sensor electrode was achieved with cyclic and differential pulse voltammetric techniques. The response of the developed sensor under the most proper conditions was linear in BPA concentration range from 4.0×10⁻⁹ to 1.0×10⁻⁷ mol L⁻¹ and 5.0×10⁻⁷ to 5.0×10⁻⁵ mol L⁻¹ and the detection limit was 4.4×10⁻⁹ mol L⁻¹. The results unclosed that the proposed sensor displayed high sensitivity and selectivity, superior electrochemical performance and rapid response to BPA.     

Graphite/Nanocrystalline Zeolite Platform for Selective Electrochemical Determination of Hepatitis C Inhibitor Ledipasvir

A simple and efficient procedure is described for the electrochemical determination of ledipasvir (LDP) in presence of co‐formulated drug sofosbuvir (SOF). Herein, a highly sensitive, low‐cost electrochemical protocol was utilized to fabricate a zeolite modified carbon paste electrode (ZY/CPE) through mixing of zeolite nanostructures with graphite powder. The fabricated sensor displayed high sensitivity, allowing optimal charge transfer/electrode kinetics. Different experimental and chemical factors, including electrode composition, effect of pH, scan rate and amount of ZY were evaluated carefully to obtain the highest electrochemical response. Under optimized conditions and using square wave voltammetry (SWV), the current response of the ZY/CPE electrochemical sensing platform exhibited a detection limit of 7.5×10^?9 M and a large linear range from 5.0×10^?8 to 1.0×10^?4 M. The practical applicability of the suggested electrochemical platform was verified in the assessment of LDP in pharmaceutical formulations with excellent recoveries in the range of 99.50–98.87 %. Moreover, a biological relevance of the developed sensor was established by the analysis of LDP in human urine and plasma samples with satisfactory recoveries of 99.00 and 99.68 %, respectively. Due to the simplicity and ease of preparation of the proposed sensor, it can be used in quality control laboratories and for clinical analysis.     

Photoluminescent energy transfer from poly(phenyleneethynylene)s to near‐infrared emitting fluorophores

Photoluminescent energy transfer was investigated in conjugated polymer‐fluorophore blended thin films. A pentiptycene‐containing poly(phenyleneethynylene) was used as the energy donor, and 13 fluorophores were used as energy acceptors. The efficiency of energy transfer was measured by monitoring both the quenching of the polymer emission and the enhancement of the fluorophore emission. Near‐infrared emitting squaraines and terrylenes were identified as excellent energy acceptors. These results, where a new fluorescent signal occurs in the near‐infrared region on a completely dark background, offer substantial possibilities for designing highly sensitive turn‐on sensors. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3382–3391, 2010     

A new near‐infrared switchable electrochromic polymer and its device application

A new near‐infrared switchable electrochromic polymer containing carbazole pendant (poly‐SNSC), synthesized by electrochemical polymerization of 2,5‐bis‐dithienyl‐1H‐pyrrole (SNS) main chain, has been prepared. The electrochemical and optical properties of SNSC monomer and its polymer have been investigated. Because of having two different electro‐donor moieties; that is, carbazole and SNS, SNSC gave two separate electrochemical oxidation and also light brown color of the film in the neutral state turn into gray on oxidation. An electrochromic device, contructed in the sandwich configuration [indium tin oxide (ITO)‐coated glass/anodically coloring polymer (poly‐SNSC)//gel electrolyte//cathodically coloring polymer (PEDOT)/ITO‐coated glass] and exhibited a high coloration efficiency (1216 cm² C^–1), a very short response time (about 0.3 s), low driving voltage, and a high redox stability. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Core‐shell type dually fluorescent polymer nanoparticles for ratiometric pH‐sensing

The synthesis and pH‐sensing properties of fluorescent polymer nanoparticles (NPs) in the 20 nm diameter range with a sensitive dye covalently attached to the particle surface and a reference dye entrapped within the particle core are presented. Fluorescein‐functionalized NPs were readily obtained by conjugation of fluorescein isothiocyanate (FITC) to amine‐coated crosslinked polystyrene‐based nanoparticles prepared by microemulsion polymerization followed by postfunctionalization. This all water‐based method gave access to stable aqueous suspensions of pH‐sensing fluorescent NPs. The encapsulation of the insensitive reference fluorescent dye (1,9‐diphenylanthracene, DPA) was then conveniently achieved by soaking leading to dual fluorescent NPs containing about 20 DPA and 55 fluorescein, as deduced from spectroscopic analyses. This core‐shell type architecture maximizes the interactions of the sensing dye with the medium while protecting the reference dye. The variations of the ratio of the fluorescence emission intensities of the sensitive dye (fluorescein) to the reference dye (DPA) with pH show that the dual fluorescent NPs act as a ratiometric pH sensor with a measuring range between pH 4 and pH 8. This pH nanosensor was found to be fast, fully reversible, and robust without any leaching of dye over a long period of time. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6206–6213, 2008     

Fiber-shaped organic electrochemical transistors for biochemical detections with high sensitivity and stability

Precise and continuous monitoring of biochemicals by biosensors assists to understand physiological functions for various diagnostics and therapeutic applications. For implanted biosensors, small size and flexibility are essential for minimizing tissue damage and achieving accurate detection. However, the active surface area of sensor decreases as the sensor becomes smaller,which will increase the impedance and decrease the signal to noise ratio, resulting in a poor detection limit. Taking advantages of local amplification effect, organic electrochemical transistors(OECTs) constitute promising candidates for high-sensitive monitoring. However, their detections in deep tissues are rarely reported. Herein, we report a family of implantable, fiber-shaped all-in-one OECTs based on carbon nanotube fibers for versatile biochemical detection including H_2O_2, glucose, dopamine and glutamate. These fiber-shaped OECTs demonstrated high sensitivity, dynamical stability in physiological environment and antiinterference capability. After implantation in mouse brain, 7-day dopamine monitoring in vivo was realized for the first time.These fiber-shaped OECTs could be great additions to the "life science" tool box and represent promising avenue for biomedical monitoring.     

Influences of three kinds of springs on the retraction of a polymer ellipsoid in dissipative particle dynamics simulation

The impacts of Rouse spring, Fraenkel spring, and one kind of finitely extensible nonlinear elastic spring (FENE‐PM spring) on the surface tension‐induced retraction of a polymer ellipsoid in a matrix were compared using dissipative particle dynamics. Using the same spring constant, obvious differences among the three kinds of springs were found. A fast retraction process was observed from the hard Fraenkel spring, a slow process from the soft Rouse spring, and an intermediate process from the FENE‐PM spring. The effects of varying the spring constant and the chain length were also investigated. The results indicate that the influence of increasing spring hardness for a given spring type was significant; whereas, the influence of chain length was minor after five bonds were reached. The effects of varying the FENE‐PM r_m parameter were also studied to provide a reliable value for this study. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Poly(Taurine‐Glutathione)/Carbon Nanotube Modified Glassy Carbon Electrode as a New Levofloxacin Sensor

A new highly sensitive and selective electrochemical levofloxacin sensor based on co‐polymer‐carbon nanotube composite electrode was developed. Taurine and Glutathione were electrochemically co‐polymerized on multiwalled carbon nanotubes modified glassy carbon electrode (Poly(TAU‐GSH)/CNT/GCE) and used as a levofloxacin sensor in pH 6 phosphate buffer solution. The new composite electrode surfaces were characterized by scanning electron microscopy, atomic force microscopy and electrochemical impedance spectroscopy. Under the optimized conditions, two linear segments were obtained for increasing LEV concentrations between 20 nmol L^?1‐1 μmol L^?1 and 1.5 μmol L^?1‐55 μmol L^?1 LEV with a detection limit of 9 nmol L^?1 using amperometry. Poly(TAU‐GSH)/CNT/GCE exhibited high sensitivity, selectivity with good stability. The new sensor was employed for real samples of LEV tablets and urine. Promising results were obtained with good accuracy which were also in accordance with LC‐MS/MS analysis.