Partially sulfonated ethylene–vinyl alcohol copolymer as new substrate for 3,4‐ethylenedioxythiophene vapor phase polymerization

A new conducting composite polymer film is obtained by vapor phase polymerization of 3,4‐ethylenedioxythiophene (EDOT) on a biocompatible polyanion derived from the partial sulfonation (32%) of statistical ethylene vinyl alcohol copolymer (EVAL32). EVALS32 and the oxidant (iron(III) p‐toluenesulfonate, [PTS]) are contemporaneously spin coated from a methanol/water solution on glass slide. EVALS32–PTS‐coated glass slides are exposed to EDOT vapors, and the polymerization is followed by Vis–NIR spectroscopy. We observed that PEDOT slowly grows into the bulk of EVALS32 matrix. Thanks to the sulfonic groups of the polyanion acting as doping agents, a highly conjugate p‐doped EVALS32‐PEDOT composite film with a good conductivity (1.6 × 10² S cm^?1), transparency, and stability in water is obtained. The EVALS32–PEDOT film seems an ideal candidate for the preparation of organic devices to be applied in electronics, biosensor, or actuation technology. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1203–1210     

Growth of poly(3,4‐ethylenedioxythiophene) films prepared by base‐inhibited vapor phase polymerization

Transparent [90% transmittance at 550 nm at a sheet resistance (R_s) of 279 Ω sq^?1] poly(3,4‐ethylenedioxythiophene) (PEDOT) films with electrical conductivities up to 1354 S cm^?1 are prepared using base‐inhibited vapor phase polymerization at atmospheric pressure. The influence of reaction conditions, such as temperature and growth time, on the film formation is investigated. A simple and convenient two‐electrode method is used for the in situ measurement of resistance, enabling to investigate the growth mechanism of polymer films and the influence of different parameters (relative humidity and the amount of oxidant) on the film growth. Low humidity exerts a detrimental effect on film growth and conductivity. In situ R_s measurements suggest that a large structural change occurs upon washing the PEDOT‐oxidant film. © 2014 Wiley Periodicals, Inc. J Polym Sci Part B: Polym. Phys. 2014 , 52, 561–571     

Vapor phase oxidative synthesis of conjugated polymers and applications

Since their discovery, electrically conductive polymers have gained immense interest both in the fields of basic and applied research. Despite their vast potential in the fabrication of efficient, flexible, and low‐cost electronic and optoelectronic devices, they are often difficult to process by wet‐chemical methods due to their very low to poor solubility in organic solvents. The use of vapor‐based synthetic routes, in which conductive polymers can be synthesized and deposited as a thin film directly on a substrate from the vapor phase, provides many unique advantages. This article discusses oxidative vapor deposition processes, primarily vapor phase polymerization and oxidative chemical vapor deposition, of conjugated polymers and their applications. The mild operating conditions (near room temperature processing) allow conformal and functional coatings of conjugated polymers on delicate substrates. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Smectic structures in electrochemically prepared poly(3,4‐ethylenedioxythiophene) films

Sub‐micrometer layers of electrochemically prepared methyl‐ and decyl‐substituted poly(3,4‐ethylenedioxythiophene) (PEDOT) carrying perchlorate counterions have been examined with grazing incidence X‐ray diffraction with synchrotron radiation. The materials were found to be partially crystalline, and the data could be ascribed to a model of sheets of π‐π stacked polymer chains with a smectic ordering of these sheets. An unsubstituted PEDOT sample with the polymeric polystyrenesulfonic acid as a counterion was also investigated and turned out to be essentially amorphous. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 945–952, 2003     

Poly(3,4‐ethylenedioxythiophene)‐based copolymers for biosensor applications

The synthesis of 3,4‐ethylenedioxythiophene (EDOT) derivatives bearing functional groups is described. Their electrochemical characteristics were investigated with cyclic voltammetry and ultraviolet–visible spectroscopy. Various copolymers of EDOT and modified EDOT containing hydroxyl groups were electrochemically prepared. The ability to bind proteins to the surface of these copolymers was investigated through the covalent coupling of glucose oxidase. The obtained materials were used as working electrodes and were shown to be able to amperometrically detect glucose under aerobic and anaerobic conditions. Possible applications of these materials as biosensors are discussed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 738–747, 2002; DOI 10.1002/pola.10159     

Synthesis of a nanosize copolymer of 3,4‐ethylenedioxythiophene with diclofenac and characterization

Copolymer of 3,4‐ethylenedioxythiophene (EDOT) and diclofenac (DCF) was synthesized by chemical oxidation using FeCl₃ in neutral medium. The copolymer exhibited good solubility in many organic solvents. The UV‐vis spectrum of the copolymer revealed the presence of benzenoid and polaron or bipolaron state. Random distribution of the monomers in the copolymer was proposed based on the reactivity ratios of the monomers determined using Fineman‐Ross and Kelen‐Tudos methods. The rate of the copolymerization depended on the first power of each monomer. The FTIR spectrum showed the presence of hydrogen bonded N‐H, quinone type structure of thiophene ring and C‐Cl bond in the copolymer. Linear variation of anodic peak current at 560 mV in the cyclic voltammogram of copolymer thin film with scan rate indicated the adherence of electroactive copolymer. When the applied potential increased from ?600 to 1000 mV, the color of the copolymer changed from neutral yellow to brown and to violet medium showing multicolor electrochromic behaviour. XRD results revealed crystallite copolymer with size 87 nm. SEM analysis confirmed uniform crystalline nature of the copolymer. The TGA, DTA and DSC studies suggested good thermal stability of the copolymer. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2787–2796, 2007     

Aminosilane SAM‐Assisted Patterning of Poly(3,4‐ethylenedioxythiophene) Nanofilm Robustly Adhered to SiO2 Substrate

To improve the patternability and adhesion of poly(3,4‐ethylenedioxythiophene) (PEDOT) nanofilm to an SiO₂ surface, an oxidized silicon wafer substrate was microcontact printed with an octadecyltrichlorosilane (OTS) monolayer, and subsequently its negative pattern was self‐assembled with (3‐aminopropyl)trimethoxysilane (APS) molecules. Then, a PEDOT nanofilm was selectively grown on the APS monolayer‐patterned area via the vapor phase polymerization (VPP) method. To evaluate the adhesion and patterning, the PEDOT nanofilm and mixed monolayer were investigated with a Scotch® tape peel test, Fourier transform infrared (FT‐IR) microspectrometer, X‐ray photoelectron spectrometer, and optical and atomic force microscopes. The evaluation revealed that the newly developed bottom‐up process can offer a robustly adhered, and selectively patterned PEDOT nanofilm on an oxidized Si wafer surface, most likely through extensive but intermittent chemical bonds between the polymer and the APS monolayer.

     

Systematic study on chemical oxidative and solid‐state polymerization of poly(3,4‐ethylenedithiathiophene)

Systematic research on the synthesis, chemical oxidative polymerization of 3,4‐ethylenedithiathiophene (EDTT) in the presence of surfactants or not, and solid‐state polymerization of 2,5‐dibromo‐3,4‐ethylenedithiathiophene (DBEDTT) and 2,5‐diiodo‐3,4‐ethylenedithiathiophene (DIEDTT) under solventless and oxidant‐free conditions has been investigated. Effects of oxidants (Fe³⁺ salts, persulfate salts, peroxides, and Ce⁴⁺ salts), solvents (H₂O, CH₃CN/H₂O, and CH₃CN), surfactants, and so forth on polymerization reactions and properties of poly(3,4‐ethylenedithiathiophene) (PEDTT) were discussed. Characterizations indicated that FeCl₃ was more suitable oxidant for oxidative polymerization of EDTT, while CH₃CN was a better solvent to form PEDTT powders with higher yields and electrical conductivities. Dispersing these powders in aqueous polystyrene sulfonic acid (PSSH) solution showed better stability and film‐forming property than sodium dodecylsulfate and sodium dodecyl benzene sulfonate. Oxidative polymerization of EDTT in aqueous PSSH solutions formed the solution processable PEDTT dispersions with good storing stability and film‐forming performance. Solvent treatment showed indistinctive effect on electrical conductivity of free‐standing PEDTT films. As‐formed PEDTT synthesized from solid‐state polymerization showed similar electrical conductivity, poorer stability, but better thermoelectric property than oxidative polymerization. Contrastingly, PEDTT synthesized from DIEDTT showed higher electrical conductivity (0.18 S cm^?1) than DBEDTT which showed better thermoelectric property with higher power factor value (6.7 × 10^?9 W m^?1 K^?2). © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Electrochromic enhancement of poly(3,4‐ethylenedioxythiophene) films functionalized with hydroxymethyl and ethylene oxide

2‐((2,3‐Dihydrothieno[3,4‐b]dioxin‐2‐yl)methoxy)methyl oxirane (EDOT‐MO) was successfully synthesized by the reaction of epichlorohydrin with hydroxymethylated‐3,4‐ethylenedioxylthiophene (EDOT‐MeOH), which was synthesized via a simple four‐step sequence. Poly(hydroxymethylated‐3,4‐ethylenedioxylthiophene) (PEDOT‐MeOH) and poly(2‐((2,3‐dihydrothieno[3,4‐b]dioxin‐2‐yl)methoxy)methyl oxirane) (PEDOT‐MO) were electrosynthesized through electropolymerization of EDOT‐MeOH and EDOT‐MO, respectively. Structural, electrochemical, optical, and thermal properties of as‐formed polymers were investigated by FTIR, cyclic voltammetry, UV–vis, and thermogravimetry. Spectroelectrochemistry studies demonstrated that PEDOT‐MeOH and PEDOT‐MO could be reversibly oxidized and reduced accompany with obvious color changes. Further kinetic studies demonstrated that the introduction of hydroxymethyl or ethylene oxide group significantly improved electrochromic properties of 3,4‐ethylenedioxythiophene (PEDOT) and resulted in high contrast ratios (57.3% at 585 nm) and coloration efficiencies (338.5 cm² C^?1), low switching voltages, and fast response time. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1989–1999     

Low‐oxidation‐potential conducting polymers derived from 3,4‐ethylenedioxythiophene and dialkoxybenzenes

Monomers derived from 3,4‐ethylenedioxythiophene and phenylenes with branched or oligomeric ether dialkoxy substituents were prepared with the Negishi coupling technique. Electrooxidative polymerization led to the corresponding dialkoxy‐substituted 3,4‐ethylenedioxythiophene–phenylene polymers, with extremely low oxidation potentials (E_1/2,p = ?0.16 to ?0.50 V vs Ag/Ag⁺) due to the highly electron‐rich nature of these materials. The polymers were electrochromic, reversibly switching from red to blue upon oxidation, with bandgaps at about 2 eV. The electrochemical behavior of the oligomeric ether‐substituted polymer was investigated in the presence of different metal ions. Films of the polymer exhibited electrochemical recognition for several alkali and alkaline‐earth cations with selectivity in the order Li⁺ > Ba²⁺ > Na⁺ > Mg²⁺. Cyclic voltammetry showed a decrease in the oxidation potential and an improvement in the definition of the voltammetric response, as well as an increase in the overall electroactivity of the polymer films when the concentration of the cations in the medium was increased. These results are discussed in terms of the electrostatic interactions between the complexed cation and the redox center, as well as the diffusion of the ionic species into the polymer matrix. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2164–2178, 2001     

Properties of In situ polymerized poly(3,4‐ethylenedioxythiophene)/alumina composites for energy storage applications

Composites formed by poly(3,4‐ethylenedioxythiophene) and alumina (PEDOT/Al₂O₃) have been prepared by in situ anodic polymerization. For this purpose, the stability of 1:1 and 4:1 monomer:alumina aqueous solutions has been examined as a function of the pH (2.3, 4.0, 7.0, 8.8, or 10.8). Results indicate that the monomer behaves as a dispersant that remains stable at the studied basic pHs despite they are close to the isoelectric point of alumina. Although the thermal stability of the composites is considerably affected by the pH of the reaction medium, its influence on the surface morphology is very small. Independently, of the synthetic conditions, the electrochemical properties were better for PEDOT/Al₂O₃ than for pure PEDOT, reflecting that alumina particles promote the charge mobility. The highest specific capacitance (SC; 141 F/g), which was 55% higher than that obtained for pure PEDOT, was achieved for the composite prepared at pH = 8.8 using a 4:1 monomer:alumina ratio. These conditions favor the participation of OH^– groups as secondary doping agents without degrading the polymer matrix and enhance the specific surface of the films, facilitating the ionic mobility. On the other hand, application of a multi‐step polymerization strategy has shown that interfaces originated by consecutive steps enhance the SC. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1131–1141     

Efficient enhancement of the thermoelectric performance of vapor phase polymerized poly(3,4‐ethylenedioxythiophene) films with poly(ethyleneimine)

Tuning the molecular rearrangement and oxidation level has been proven to be effective strategies for optimizing the thermoelectric (TE) performance of PEDOT. It is difficult to achieve these effects simultaneously via a one‐step process, however. In this work, we combined vapor phase polymerization (VPP) and H₂SO₄ post‐treatment to obtain a highly conductive PEDOT film. A novel strategy using polyethylenemine (PEI) as an effective reducing agent was employed to enhance the thermopower of the PEDOT film. Grazing‐Incidence Wide‐Angle X‐ray Scattering analysis and the changes in the oxidation level allow us to elucidate the role of PEI and its transport mechanism. It is demonstrated that the thermopower of well‐ordered crystallites in the PEDOT film significantly increases more than five times (from 11 to 59 μV K^?1) by the PEI‐DMF solution immersion process, while the electrical conductivity is maintained at 100 S cm^?1. The promising method connecting VPP, H₂SO₄, and PEI shows great potential for effectively tuning the thermopower of organic TE materials. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 257–265     

A Free‐standing electrochromic material of poly(5,7‐bis(2‐(3,4‐ethylenedioxy)thienyl)‐indole) and its application in electrochromic device

Free‐standing poly(5,7‐bis(2‐(3,4‐ethylenedioxy)thienyl)‐indole) (PETI) was electrochemically obtained from 5,7‐bis(2‐(3,4‐ethylenedioxy)thienyl)‐indole (ETI) prepared by Stille coupling reaction of 5,7‐dibromoindole and 3,4‐ethylenedioxythiophene. For comparison, poly(5,7‐bis(2‐thiophene)‐indole) was also electrosynthesized from 5,7‐bis(2‐thiophene)‐indole (BTI) which was prepared from the 5,7‐dibromoindole and thiophene. Characterizations of ETI and BTI were performed by cyclic voltammetry, scanning electron microscopy, ¹H NMR, and ¹³C NMR spectroscopy. Spectroelectrochemical studies showed PETI had better electrochromic properties and showed two different colors (brown and blue‐violet) under various potentials with better maximum contrast (ΔT%) and coloration efficiency (CE). An electrochromic device (ECD) based on PETI and poly(3,4‐ethylenedioxythiophene) (PEDOT) was also constructed and characterized. This ECD had fast response time, high CE, better optical memory, and long‐term stability. These results indicated that PETI had potential applications for ECD. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2356–2364     

Detrimental Ni(0) transfer in Kumada catalyst transfer polycondensation of benzo[2,1‐b:3,4‐b']dithiophene

This article deals with the Kumada Catalyst Transfer Polycondensation (KCTP) of 4,7‐dioctylbenzo[2,1‐b:3,4‐b']dithiophene ( BDP‐Oct ) using Ni(II) catalyst or In/cat combination. A combination of MALDI MS, GPC, and ³¹P NMR spectroscopy is used to reveal the failure of the KCTP of this particular monomer. Intermolecular transfer reactions to monomer appeared to prevent the formation of polymer. This result is remarkable, since isomeric benzo[1,2‐b:4,5‐b']dithiophene polymerizes in a controlled way. The presence of a “non‐aromatic double bond” in annulated monomers is discussed. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1706–1712     

Functional polyesters prepared by polymerization of α‐allyl(valerolactone) and its copolymerization with ε‐caprolactone and δ‐valerolactone

We report the ring‐opening homopolymerization of α‐allyl(valerolactone), compound 2 , and its copolymerization with ε‐caprolactone and δ‐valerolactone using stannous(II) catalysis. Although the polymerization of substituted δ‐valerolactones has received little attention for the preparation of functional polyesters, we found that compound 2 may be incorporated in controllable amounts into copolymers with other lactones, or simply homopolymerized to give a highly functionalized, novel poly(valerolactone). The presence of the pendant allyl substituent had a substantial impact on the thermal properties of these materials relative to conventional polyesters prepared from lactones, and most of the polymers presented here are liquids at room temperature. Dihydroxylation of the pendant allyl groups gave polyesters with increased hydrophilicity that degraded more or less rapidly depending on their extent of functionality. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1983–1990, 2002     

Synthesis of Poly(3,4‐ethylenedioxythiophene) latexes using poly(N‐vinylpyrrolidone)‐based copolymers as reactive stabilizers

The synthesis by oxidative polymerization of well‐defined poly(3,4‐ethylenedioxythiophene) (PEDOT) nano‐objects in the presence of modified and unmodified poly(N‐vinylpyrrolidone)‐based copolymers used as stabilizers in aqueous media is reported. Ammonium persulfate or a mixture of ammonium persulfate with CuCl₂ or CuBr₂ was used as oxidants. The effects of several parameters such as the molar mass and the concentration of the stabilizer as well as the nature of the oxidants on the size, morphology, and the conductivity of the PEDOT particles have been investigated. The distribution of the reactive moieties along the copolymer stabilizer backbone was shown to be crucial to get well‐defined PEDOT nano‐objects. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3841–3855, 2010     

Conducting core‐sheath nanofibers for electroactive shape‐memory applications

Conducting nanofibers coated with polypyrrole (PPy) and poly(3‐hexylthiophene) (P3HT) exhibiting core‐sheath structures were prepared by vapor‐phase polymerization of the conducting polymers on electrospun polyurethane nanofibers. The synthesis of the conducting polymers was confirmed by Fourier transform infrared spectroscopy and energy‐disperse X‐ray spectroscopy. The surfaces of the PPy‐coated nanofibers were slightly rough, while very smooth and regular surfaces were observed in the case of the P3HT‐coated nanofibers. The initial polymerization rate of PPy was higher than that of P3HT. In addition, the electrical conductivities of the core‐sheath structured nanofiber webs of both types increased with polymerization time. The maximum sheet conductivity of the PPy and P3HT‐coated nanofiber webs was 5 × 10^?3 S/cm and 1 × 10^?2 S/cm, respectively. The webs of the conducting core‐sheath structured nanofibers were effective in generating sufficient electrical heating necessary for harnessing these materials for electroactive shape‐memory‐based applications. Copyright © 2013 John Wiley & Sons, Ltd.     

Anionic polymerization of 4‐phenyl‐1‐buten‐3‐yne derivatives bearing electron‐withdrawing groups

The anionic polymerization of derivatives of 4‐phenyl‐1‐buten‐3‐yne was carried out to investigate the effect of substituents on the polymerization behavior. The polymerization of 4‐(4‐fluorophenyl)‐1‐buten‐3‐yne and 4‐(2‐fluorophenyl)‐1‐buten‐3‐yne in tetrahydrofuran at −78 °C with n‐BuLi/sparteine as an initiator gave polymers consisting of 1,2‐ and 1,4‐polymerized units in quantitative yields with ratios of 80/20 and 88/12, respectively. The molecular weights of the polymers were controlled by the ratio of the monomers to n‐BuLi, and the distribution was relatively narrow (weight‐average molecular weight/number‐average molecular weight < 1.2), supporting the living nature of the polymerization. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1016–1023, 2001