Nanofibrosis of uncrystallizable poly(lactide‐co‐glycolide) via phase separation

Poly(lactide‐co‐glycolide) (PLGA) copolymers are a kind of biocompatible and biodegradable materials being widely used in tissue engineering. However, phase separation had not been reported successfully in fabricating these amorphous polymers into nanofibrous matrix, although this technique had shown advantages over electrospinning in producing a nanofiber network. In this study, tetrahydrofuran (THF)/H₂O solvent pairs were found suitable solvents to induce the formation of uniform PLGA gel at selected gelation temperatures. The results indicated that fine nanofibrous structures with fiber diameter around 40–60 nm could be obtained following the steps of gel formation, solvent extraction, and freeze‐drying, by controlling the concentration of PLGA/THF/H₂O solution, THF/H₂O ratio, and gelation temperature. Copyright © 2009 John Wiley & Sons, Ltd.     

Crosslinking of Poly(L‐lactide) by γ‐Irradiation

The radiation crosslinking of poly(L ‐lactide) (PLLA) was investigated using triallyl isocyanurate (TAIC) as a crosslinking agent. The gel fraction of crosslinked PLLA increased with TAIC concentration and γ‐ray dose. Crosslinking of PLLA started at low TAIC contents and low γ‐ray dosage. Differential scanning calorimetry and dynamic mechanical thermal analysis revealed that PLLA was completely crosslinked at high weight ratios and high γ‐ray doses.     

Relationship among drug delivery behavior,degradation behavior and morphology of copolylactones derived from glycolide,l‐lactide and ε‐caprolactone

A series of copolylactones was synthesized by ring‐opening copolymerization of glycolide, L ‐lactide and ?‐caprolactone, using stannous octoate as catalyst. The in vitro degradation behaviors of them were studied and data demonstrated different degradation rates which mainly depended on the compositions. Investigation of the 5‐fluorouracil (5‐Fu) release from these copolylactones revealed that the composition, degradation rate and the morphology of the polymeric matrix played an important role on the drug release kinetics. A sustained 5‐Fu release without initial time lag was obtained from random poly(lactide‐co‐glycolide‐co‐caprolactone) (r‐PGLC) drug carrier, and it differed from the cases of polylactide (PLA) or random poly(lactide‐co‐glycolide) (PLGA), which usually showed an initial time lag or biphasic drug release behavior. It was due to the low glass transition temperature (T _g) of the r‐PGLC and the drug would diffuse faster in rubbery state under the experimental temperature. Furthermore, a significant change in the drug release behavior of r‐PGLC was observed when the temperatures were changed around the T _g of the drug carrier, which implied that the drug release behavior could be regulated by adjusting the morphology of the drug carrier. Copyright © 2002 John Wiley & Sons, Ltd.     

Fabrication of poly(lactide‐co‐glycolide) scaffold embedded spatially with hydroxyapatite particles on pore walls for bone tissue engineering

Poly(lactide‐co‐glycolide) (PLGA) scaffolds embedded spatially with hydroxyapatite (HA) particles on the pore walls (PLGA/HA‐S) were fabricated by using HA‐coated paraffin spheres as porogens, which were prepared by Pickering emulsion. For comparisons, PLGA scaffolds loaded with same amount of HA particles (2%) in the matrix (PLGA/HA‐M) and pure PLGA scaffolds were prepared by using pure paraffin spheres as porogens. Although the three types of scaffolds had same pore size (450–600 µm) and similar porosity (90%–93%), the PLGA/HA‐S showed the highest compression modulus. The embedment of the HA particles on the pore walls endow the PLGA/HA‐S scaffold with a stronger ability of protein adsorption and mineralization as well as a larger mechanical strength against compression. In vitro culture of rat bone marrow stem cells revealed that cell morphology and proliferation ability were similar on all the scaffolds. However, the alkaline phosphatase activity was significantly improved for the cells cultured on the PLGA/HA‐S scaffolds. Therefore, the method for fabricating scaffolds with spatially embedded nanoparticles provides a new way to obtain the bioactive scaffolds for tissue engineering. Copyright © 2011 John Wiley & Sons, Ltd.     

Biocompatibility evaluation of self‐assembled micelles prepared from poly(lactide‐co‐glycolide)‐poly(ethylene glycol) diblock copolymers

In this work, a series of PLGA‐PEG diblock copolymers were synthesized by ring‐opening polymerization of L‐lactide and glycolide using mPEG as macroinitiator and stannous octoate as catalyst. Spherical micelles were obtained from the various copolymers by using co‐solvent evaporation method. The biocompatibility of micelles was evaluated with the aim of assessing their potential in the development of drug delivery systems. Various aspects of biocompatibility were considered, including MTT assay, agar diffusion test, release of cytokines, hemolytic test, dynamic clotting time, protein adsorption in vitro, and zebrafish embryonic compatibility in vivo. The combined results revealed that the micelles present good cytocompatibility and hemocompatibility in vitro. Moreover, the cumulative effects of micelles throughout embryos developing stages have no toxicity in vivo. It is thus concluded that micelles prepared from PLGA‐PEG copolymers present good biocompatibility as potential drug carrier.     

Hyperbranched poly (amine‐ester)‐poly (lactide‐co‐glycolide) copolymer and their nanoparticles as paclitaxel delivery system

A new hyperbranched poly (amine‐ester)‐poly (lactide‐co‐glycolide) copolymer (HPAE‐co‐PLGA) was synthesized by ring‐opening polymerization of D , L ‐lactide (DLLA) glycolid and branched poly (amine‐ester) (HPAE‐OHs) with Sn(Oct)₂ as catalyst. The chemical structures of copolymers were determined by FT‐IR, ¹H‐NMR(¹³C NMR), TGA and their molecular weights were determined by gel permeation chromatography (GPC). Paclitaxel‐loaded copolymer nanoparticles were prepared by the nanoprecipitation method. Their physicochemical characteristics, e.g. morphology and nanoparticles size distribution were then evaluated by means of fluorescence spectroscopy, environmental scanning electron microscopy (ESEM), and dynamic light scattering (DLS). Paclitaxel‐loaded nanoparticles assumed a spherical shape and have unimodal size distribution. It was found that the chemical composition of the nanoparticles was a key factor in controlling nanoparticles size, drug‐loading content, and drug release behavior. As the molar ratio of DL ‐lactide/glycolide to HPAE increased, the nanoparticles size and drug‐loading content increased, and the drug release rate decreased. The antitumor activity of the paclitaxel‐loaded HPAE‐co‐PLGA nanoparticles against human liver cancer H7402 cells was evaluated by 3‐(4, 5‐dimethylthiazol‐2‐yl)‐2,5‐diphenyl tetrazolium bromide (MTT) method. The paclitaxel‐loaded HPAE‐co‐PLGA nanoparticles showed comparable anticancer efficacy with the free drug. Copyright © 2010 John Wiley & Sons, Ltd.     

Emulsion copolymerization of D,L‐lactide and glycolide in supercritical carbon dioxide

Biodegradable polyesters were synthesized via an emulsion polymerization in supercritical carbon dioxide (SC‐CO₂). Copolymers of lactide and glycolide were synthesized in SC‐CO₂ with stannous octoate as the ring‐opening catalyst and a fluorocarbon polymer surfactant as an emulsifying agent. The conversion of lactide and glycolide was monitored with respect to the reaction time and temperature with ¹H NMR spectroscopy. The conversion of glycolide surpassed 99% within 72 h for an SC‐CO₂ phase maintained at 200 bar and 70 °C. Under the same conditions, lactide conversion reached 65% after 72 h of polymerization. Unpolymerized monomer was removed after the reaction by extraction with an SC‐CO₂ mobile phase. The molecular weights of all the copolymers were measured by gel permeation chromatography. Weight‐average molecular weights (M_w) ranged between 2500 and 30,200 g/mol and polydispersity indices ranged from 1.4 to 2.3 for polymerization times of 6 and 48 h, respectively. Although the molecular weight increased significantly during the first 48 h of reaction, there was no significant difference in the M_w for polymerization times of 48 and 72 h. Emulsion polymerization within the benign solvent SC‐CO₂ demonstrated improved conversion and molecular weight versus polymers synthesized without surfactant. The emulsion polymerization of lactide and glycolide copolymers in SC‐CO₂ is proposed as a novel production technique for high‐purity, biodegradable polymers. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 562–570, 2001     

Synthesis and characterization of tercopolymers derived from ε‐caprolactone,trimethylene carbonate,and lactide

A series of tri‐components copolymers with different molar ratios were synthesized via bulk ring‐opening copolymerization of trimethylene carbonate (TMC), L ‐lactide (LLA), and ε‐caprolactone (ε‐CL), using stannous octoate as catalyst. The sequence structure of the tercopolymer chain was characterized by ¹H and ¹³C nuclear magnetic resonance (NMR), Fourier transform infrared (FTIR), and gel permeation chromatography (GPC). The results showed that although block sequence of the corresponding monomers still existed in the tercopolymer chain, the random tercopolymers were ultimately obtained due to the transesterification during polymerization. For the samples TP1 and TP2, longer sequence of LLA existed in the molecular chains. The thermal properties of tercopolymers were investigated by differential scanning calorimetry (DSC) and the mechanical properties of the resulting copolymers were studied by using a tensile tester. The results indicated that the properties of these copolymers could be adjusted by changing the compositions of the copolymers. The resulting tercopolymers are expected to have potential uses as nerve regeneration and other biomedicine materials. Copyright © 2007 John Wiley & Sons, Ltd.     

二元溶剂分散法制备PLA和PLGA纳米粒

聚乳酸;聚丙交酯乙交酯;二元溶剂分散法制备PLA和PLGA纳米粒     

New Strategy for Controlling Biodegradability of Biodegradable Polyesters by Enzyme‐Catalyzed Surface Grafting

A novel preparation method for the core‐shell type biodegradable polyesters or biodegradable materials grafted with biodegradable polyesters was developed by alkaline surface treatment of biodegradable polyester films and subsequent enzymatic polymerization of aliphatic lactones, one example of which is shown in this study, i.e., the preparation of poly(L ‐lactide) (PLLA) film grafted with poly(ε‐caprolactone). It is revealed that only alkaline surface treatment or the combination of alkaline surface treatment and enzyme‐catalyzed grafting, the former and the latter, respectively accelerating and delaying the enzymatic degradation of PLLA, will give PLLA materials having a wide variety of biodegradability. Also, the specificity of the enzyme used for hydrolysis could be used to confirm the grafted chain species.

     

Mechanism of high thermal stability of commercial polyesters and polyethers conjugated with bio‐based caffeic acid

In previous report, we discovered that a novel improvement technique to enhance the thermal properties of poly(L ‐lactide)s (PLLAs) by terminal conjugation with 3,4‐diacetoxycinnamic acid (DACA). In this study, we clarified the mechanism of the enhancement of thermal stability by using commercial polyesters and polyethers. The effect of thermal improvement by the terminal conjugation of DACA on poly(DL ‐lactide), poly(ε‐caprolactone), and poly(ethylene glycol) was almost the same as about 100 °C increase. The amount of residual tin catalyst, which enhances the thermal degradation of polyesters, was reduced at undetected level after the terminal conjugation of DACA probably due to the removal of tin during DACA conjugation process. Furthermore, the π‐π stacking interactions of DACA units and the chemical protection of terminal hydroxyl groups, which enhances intramolecular scission, were also important for the high thermal stability. We clarified that the extreme high thermal stability by DACA conjugation was induced by these above mechanisms. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Toughening modification of PLLA with PCL in the presence of PCL‐b‐PLLA diblock copolymers as compatibilizer

To obtain an effective compatibilizer for the blends of poly(L‐lactide) (PLLA) and poly(ε‐caprolactone) (PCL), the diblock copolymers PCL‐b‐PLLA with different ratios of PCL/PLLA (CL/LA) and different molecular weights (M_n) were synthesized by ring‐opening polymerization (ROP) of L‐lactide with monohydric poly(ε‐caprolactone) (PCL‐OH) as a macro‐initiator. These copolymers were melt blended with PLLA/PCL (80/20) blend at contents between 3.0 and 20 phr (parts per hundred resin), and the effects of added PCL‐b‐PLLA on the mechanical, morphological, rheological, and thermodynamic properties of the PLLA/PCL/PCL‐b‐PLLA blends were investigated. The compatibility between PLLA matrix and PCL phase was enhanced with decreasing in CL/LA ratios or increasing in M_n for the added PCL‐b‐PLLA. Moreover, the crystallinity of PLLA matrix increased because of the added compatibilizers. The PCL‐b‐PLLA with the ratio of CL/LA (50/50) and M_n ≥ 39.0 kg/mol were effective compatibilizers for PLLA/PCL blends. When the content of PCL‐b‐PLLA is greater than or equal to 5 phr, the elongations at break of the PLLA/PCL/PCL‐b‐PLLA blends all reached approximately 180%, about 25 times more than the pristine PLLA/PCL(80/20) blend.     

Water‐disintegrative and biodegradable blends containing poly(L‐lactic acid) and poly(butylene adipate‐co‐terephthalate)

In this study, novel biodegradable materials were successfully generated, which have excellent mechanical properties in air during usage and storage, but whose structure easily disintegrates when immersed in water. The materials were prepared by melt blending poly(L ‐lactic acid) (PLLA) and poly(butylene adipate‐co‐terephthalate) (PBAT) with a small amount of oligomeric poly(aspartic acid‐co‐lactide) (PAL) as a degradation accelerator. The degradation behavior of the blends was investigated by immersing the blend films in phosphate‐buffered saline (pH = 7.3) at 40 °C. It was shown that the PAL content and composition significantly affected morphology, mechanical properties, and hydrolysis rate of the blends. It was observed that the blends containing PAL with higher molar ratios of L ‐lactyl [LA]/[Asp] had smaller PBAT domain size, showing better mechanical properties when compared with those containing PAL with lower molar ratios of [LA]/[Asp]. The degradation rates of both PLLA and PBAT components in the ternary blends simultaneously became higher for the blends containing PAL with higher molar ratios of [LA]/[Asp]. It was confirmed that the PLLA component and its decomposed materials efficiently catalyze the hydrolytic degradation of the PBAT component, but by contrast that the PBAT component and its decomposed materials do not catalyze the hydrolytic degradation of the PLLA component in the blends. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Novel biomimetic composite based on collagen and poly(γ‐benzyl L‐glutamate)‐co‐poly(glutamic acid)

Novel biomimetic composite was prepared by the reaction of collagen and poly(γ‐benzyl L ‐glutamate)‐co‐poly(glutamic acid) (PBLG‐co‐PGA), which were crosslinked by non‐toxic crosslinking reagents 1‐ethyl‐(dimethylaminopropyl) carbodiimide (EDC) and N‐hydroxysuccinimide (NHS). The composite was characterized by FTIR and DSC. FTIR results confirmed that the collagen in the composite was successfully crosslinked with PBLG‐co‐PGA. DSC results showed that the composites possessed higher shrinkage temperature and higher thermal stability than the collagen. The water absorption test showed that the water absorbency of the composites increased with the increase in PBLG‐co‐PGA content in the composite. The studies of collagenase degradation and the tensile strength showed that the biostability and the tensile strength of the composites were significantly improved in comparison with that of the collagen. According to the investigations of cell adherent ratio and cell proliferation in vitro, the composite possessed good biocompatibility. Copyright © 2007 John Wiley & Sons, Ltd.     

Syntheses of trimethoxysilyl‐endcapped polylactones via 3‐mercaptopropyl trimethoxysilane

Monofunctional polylactones were prepared by Bu₂Sn(OMe)₂‐initiated ring‐opening polymerization of ε‐caprolactone (εCL) followed by acylation with bromoacetylbromide. Telechelic polylactones and polylactides were prepared via ring‐expansion polymerization with 2,2‐dibutyl‐2‐stanna‐1,3‐dioxepane (DSDOP) or 2,2‐dibutyl‐2‐stanna‐pentaoxacyclotridecane (Bu₂SnTEG) as cyclic initiator. In situ combination of the polymerization with condensation by means of bromoacetylbromide yielded polylactones having bromoacetate endgroups. These endgroups were subjected to nucleophilic substitution with 3‐mercaptopropyl trimethoxysilane (3‐MPTMS). Analogous experiments were conducted with dl‐lactide. The telechelic trimethoxysilyl‐endcapped polylactones were characterized by viscosity, ¹H and ¹³C NMR‐spectroscopy, and MALDI‐TOF mass spectrometry. The mass spectra revealed small amounts of cyclic oligolactones as byproducts in all samples. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3667–3674, 2005     

Composites of poly(L‐lactide‐trimethylene carbonate‐glycolide) and surface modified SBA‐15 as bone repair material

This work aims to develop novel composites from a poly(L ‐lactide‐co‐trimethylene carbonate‐co‐glycolide) (PLTG) terpolymer and mesoporous silica (SBA‐15) nanofillers surface modified by post‐synthetic functionalization. SBA‐15 first reacts with a silane coupling agent, γ‐aminopropyl‐trimethoxysilane to introduce ammonium group. PLLA chains were then grafted on the surface of SBA‐15 through ammonium initiated ring‐opening polymerization of L ‐lactide. Composites were prepared via solution mixing of PLTG terpolymer and surface modified SBA‐15. The structures and properties of pure SBA‐15, γ‐aminopropyl‐trimethoxysilane modified SBA‐15 (H₂N‐SBA‐15), PLLA modified SBA‐15 (PLLA‐NH‐SBA‐15), and PLTG/PLLA‐NH‐SBA‐15 composites were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, X‐ray diffraction, scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, transmission electron microscopy, N₂ adsorption‐desorption, differential scanning calorimetry, contact angle measurement, and mechanical testing. The results demonstrated that PLLA chains were successfully grafted onto the surface of SBA‐15 with grafting amounts up to 16 wt.%. The PLTG/PLLA‐NH‐SBA‐15 composites exhibit good mechanical properties. The tensile strength, Young's modulus, and elongation at break of the composite containing 5 wt.% of PLLA‐NH‐SBA‐15 were 39.9 MPa, 1.3 GPa, and 273.6%, respectively, which were all higher than those of neat PLTG or of the composite containing 5 wt.% of pure SBA‐15. Cytocompatibility tests showed that the composites present very low cytotoxicity.     

Highly porous poly(lactide‐co‐glycolide) microparticles for sustained tiotropium release

In this study, porous poly(lactide‐co‐glycolide) (PLGA) microparticles with low mass density and large particle size were developed for chronic obstructive pulmonary disease treatment using anticholinergic drug (tiotropium). The porous PLGA microparticles were prepared by the water‐in‐oil‐in‐water (W₁/O/W₂) multi‐emulsion method using PLGA polymer and ammonium bicarbonate (as a porogen). Herein, soluble starch was incorporated in porous PLGA microparticles for long‐term tiotropium release. In vitro drug release studies determined that the rapid release of tiotropium from porous PLGA microparticles was reduced because of the high viscosity of the incorporated starch. Tiotropium release from porous PLGA microparticles continued up to 3 days. Furthermore, the inhaled microparticles showed longer drug residence in in vivo lung epithelium. Copyright © 2013 John Wiley & Sons, Ltd.     

Synthesis and properties of photocurable biodegradable multiblock copolymers based on poly(ε‐caprolactone) and poly(L‐lactide) segments

Photocurable biodegradable multiblock copolymers were synthesized from poly(ε‐caprolactone) (PCL) diol and poly(L ‐lactide) (PLLA) diol with 4,4′‐(adipoyldioxy)dicinnamic acid (CAC) dichloride as a chain extender derived from adipoyl chloride and 4‐hydroxycinnamic acid, and they were characterized with Fourier transform infrared and ¹H NMR spectroscopy, gel permeation chromatography, wide‐angle X‐ray diffraction, differential scanning calorimetry, and tensile tests. The copolymers were irradiated with a 400‐W high‐pressure mercury lamp from 30 min to 3 h to form a network structure in the absence of photoinitiators. The gel concentration increased with time, and a concentration of approximately 90% was obtained in 90–180 min for all the films. The photocuring hardly affected the crystallinity and melting temperature of the PCL segments but reduced the crystallinity of the PLLA segments. The mechanical properties, such as the tensile strength, modulus, and elongation, were significantly affected by the copolymer compositions and gel concentrations. Shape‐memory properties were determined with cyclic thermomechanical experiments. The CAC/PCL and CAC/PCL/PLLA (75/25) films photocured for 30–120 min showed good shape‐memory properties with strain fixity rates and recovery rates of approximately 100%. The formation of the network structure and the crystallization and melting of the PCL segments played very important roles for the typical shape‐memory properties. Finally, the degradation characteristics of these copolymers were investigated in a phosphate buffer solution at 37 °C with proteinase‐k and Pseudomonas cepacia lipase. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2426–2439, 2005