Stimulated emission and ultrafast optical switching in a ter(9,9′‐spirobifluorene)‐co‐methylmethacrylate copolymer

A methacrylate‐functionalized 9,9′‐spirobifluorene trimer is copolymerized with methylmethacrylate (MMA). The photophysical characterization of this copolymer using pump‐probe studies, in solution, as films and in plastic optical fibers (POFs) demonstrates that it shows interesting photonic properties for data communication such as high‐stimulated emission cross section (σ_SE = 2.5 × 10^?16 cm²), good thermal, and optical stability, the ability to perform all‐optical ultrafast switching, and low attenuation when doped into POFs. In addition, the material shows interesting optically induced conformational control in solution and the studies demonstrate the surprising result that intrachain polaron pairs can be generated even in well‐isolated 3‐unit oligomers. Although the material is not yet soluble enough in MMA to create highly efficient photonic devices and the gain spectrum is not optimized to overlap with the region of low attenuation in polymethylmethacrylate POFs, these studies are a good starting point to further optimize copolymers for incorporation into POF networks. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Development of hydrogenated ring‐opening metathesis polymers

New hydrogenated ring‐opening metathesis polymers with excellent thermal and optical properties were developed. These polymers were prepared by the ring‐opening metathesis polymerization of ester‐substituted tetracyclododecene monomers followed by the hydrogenation of the main‐chain double bond. The degree of hydrogenation was an important factor for the thermal stability of the polymers, and as complete hydrogenation as possible was necessary to obtain a thermally stable polymer. The completely hydrogenated ring‐opening polymer derived from 8‐methyl‐8‐methoxycarbonyl‐substituted monomer has a glass‐transition temperature of 171 °C and a 5% weight‐loss temperature of 446 °C. This polymer has excellent thermal and optical properties because of its bulky and unsymmetrical polycyclic structure in the main chain and is an alternative to glass or other transparent polymers such as poly(methyl methacrylate) and polycarbonate resin. This polymer has also been used in a wide variety of applications, such as optical lenses, optical disks, optical films, and optical fiber. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4661–4668, 2000     

Carbon–silica dual‐phase filler,a new‐generation reinforcing agent for rubber. Part VI. Time–temperature superposition of dynamic properties of carbon–silica‐dual‐phase‐filler‐filled vulcanizates

Dynamic properties such as shear modulus, loss modulus, and loss factor were obtained at a low strain amplitude over a wide range of frequencies and temperatures on vulcanizates filled with carbon black, silica, and carbon–silica dual‐phase filler. The data were shifted along the frequency scale. Instead of a single smooth master curve, a pseudomaster curve with a feather‐like structure is obtained. This effect is especially pronounced for the loss factor. Multiple factors may be responsible for this. Among others, filler networking and polymer–filler interaction may play a dominant role. The effect of the carbon–silica dual‐phase filler on the overall dynamic properties of the vulcanizates is similar to that of silica. Their tan δ values are much lower at lower frequencies and are relatively higher at higher frequencies. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1240–1249, 2000     

多模梯度（聚焦）型塑料光纤研究进展

多模梯度型塑料光纤，其折光 率径向分布呈连续的抛物线型分布。光在这种纤维中的行程按正弦波前进。这类纤维具有频带宽、传输容量大，信号保真度高的优点。本文就二十多年来有关ＧＩＰＯＦ的研究进展进行了较全面的综述。     

Mixed‐Matrix Membranes

Research into extended porous materials such as metal‐organic frameworks (MOFs) and porous organic frameworks (POFs), as well as the analogous metal‐organic polyhedra (MOPs) and porous organic cages (POCs), has blossomed over the last decade. Given their chemical and structural variability and notable porosity, MOFs have been proposed as adsorbents for industrial gas separations and also as promising filler components for high‐performance mixed‐matrix membranes (MMMs). Research in this area has focused on enhancing the chemical compatibility of the MOF and polymer phases by judiciously functionalizing the organic linkers of the MOF, modifying the MOF surface chemistry, and, more recently, exploring how particle size, morphology, and distribution enhance separation performance. Other filler materials, including POFs, MOPs, and POCs, are also being explored as additives for MMMs and have shown remarkable anti‐aging performance and excellent chemical compatibility with commercially available polymers. This Review briefly outlines the state‐of‐the‐art in MOF‐MMM fabrication, and the more recent use of POFs and molecular additives.     

Characterization of thermo-oxidative stability of polymer optical fibers using chemiluminescence technique

The thermo-oxidative stability of commercially available polymer optical fibers (POFs) and their components (cores and claddings) was investigated. All the bare POFs (core and cladding only) studied here were based on poly(methyl methacrylate) (PMMA) core. The fibers were exposed to 100 °C/low humidity for about 4200 h. Chemiluminescence (CL) technique was applied to investigate the thermo-oxidative stability and for measuring the transmission loss during exposure a prototype device called multiplexer was used. POFs exhibited variation in thermo-oxidative stability although they possessed identical core material PMMA. This was due to difference in the chemical compositions of claddings. Claddings were more susceptible to the thermo-oxidative degradation compared to cores. The thermo-oxidative degradation of both the cladding and the core was found in POFs as a result of climatic exposure. POFs showed an early drop-off followed by a slow decline of transmission. The early drop-off of transmission was attributed to physical changes like thermal expansion and the slow decline of transmission to chemical changes like oxidative degradation of POFs. A good linear relationship between optical transmission stability and thermo-oxidative stability of POFs was established from these studies.     

Surface modification of ultrahigh‐molecular‐weight polyethylene fibers

To prevent the loss of fiber strength, ultrahigh‐molecular‐weight polyethylene (UHMWPE) fibers were treated with an ultraviolet radiation technique combined with a corona‐discharge treatment. The physical and chemical changes in the fiber surface were examined with scanning electron microscopy and Fourier transform infrared/attenuated total reflectance. The gel contents of the fibers were measured by a standard device. The mechanical properties of the treated fibers and the interfacial adhesion properties of UHMWPE‐fiber‐reinforced vinyl ester resin composites were investigated with tensile testing. After 20 min or so of ultraviolet radiation based on 6‐kW corona treatment, the T‐peel strength of the treated UHMWPE‐fiber composite was one to two times greater than that of the as‐received UHMWPE‐fiber composite, whereas the tensile strength of the treated UHMWPE fibers was still up to 3.5 GPa. The integrated mechanical properties of the treated UHMWPE fibers were also optimum. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 463–472, 2004     

High‐thermally stable and high‐bandwidth graded index plastic optical fiber for vehicle networks

Radial refractive index profiles within the graded index plastic optical fiber (GI‐POF) is formed by adding a dopant to a polymer. This addition of the dopant significantly decreased the T_g of the polymer due to the plasticization. This disadvantage made the installation of the GI‐POF difficult, especially in vehicle networks in which high thermal stability is required. We have suggested 9‐bromophenanthrene (BPT) as a novel dopant induced less plasticization for poly(methyl methacrylate) (PMMA) than the conventional dopants. However, although the fabricated GI‐POF using BPT had high enough thermal stability for vehicle networks, the attenuation was 800 dB/km and it could not be used. This high attenuation was caused by contaminant in the fabrication process of fibers. In this study, we succeeded to fabricate a GI‐POF with low‐attenuation and high‐thermal stability using highly pure BPT. Its attenuation was improved to 240 dB/km at 650 nm, which was enough transparency for vehicle networks. The T_g of the GIPOF was improved to 107 °C from 90 °C. The thermal stability of the GI‐POF below 85 °C/dry and 75 °C/85%RH was demonstrated to be as high as that of the commercially available step index POF. The bandwidth of the GI‐POF could be estimated over 4.0 GHz for the 50‐m fiber. These results demonstrated that our GI‐POF should qualify to be used in vehicle network. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1464–1469, 2011     

Preparation of plastic optical fibers for near-IR region transmission

Loss factors of PMMA and PS core plastic optical fibers (POFs) were analyzed, and it was revealed that the vibrational absorption owing to CH vibration plays the most significant role in reducing the near-IR region attenuation loss. Conversion of the hydrogen of the CH bond in the core polymer to deuterium gives rise to a large reduction of the attenuation loss not only in the visible wavelength region but also in the near-IR region. The deuteration of styrene is not so effective as that of methyl methacrylate because of PS core POFs higher loss owing to imperfections in the wave guide structure and Rayleigh scattering. Using a perdeuterated PMMA as a POF core, a loss of 20 dB/km was attained in the 650–680 nm wavelength region. The loss limits of these deuterated polymer core POFs were also estimated.     

Ultrahigh‐molecular‐weight‐polyethylene‐fiber surface treatment by electron‐beam‐irradiation‐induced graft polymerization and its effect on adhesion in a styrene–butadiene rubber matrix

Aiming to develop a high‐performance fiber‐reinforced rubber from styrene–butadiene rubber (SBR), we applied a special technique using electron‐beam (EB)‐irradiation‐induced graft polymerization to ultrahigh‐molecular‐weight‐polyethylene (UHMWPE) fibers. The molecular interaction between the grafted UHMWPE fibers and an SBR matrix was studied through the evaluation of the adhesive behavior of the fibers in the SBR matrix. Although UHMWPE was chemically inert, two monomers, styrene and N‐vinyl formamide (NVF), were examined for graft polymerization onto the UHMWPE fiber surface. Styrene was not effective, but NVF was graft‐polymerized onto the UHMWPE fibers with this special method. A methanol/water mixture and dioxane were used as solvents for NVF, and the effects of the solvents on the grafting percentage of NVF were also examined. The methanol/water mixture was more effective. A grafting percentage of 16.4% was the highest obtained. This improved the adhesive force threefold with respect to that of untreated UHMWPE fibers. These results demonstrated that EB irradiation enabled graft polymerization to occur even on the inert surface of UHMWPE fibers. However, the mechanical properties of the fibers could be compromised according to the dose of EB irradiation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2595–2603, 2004     

Gel–sol transition for soluble polyimide solution

Copolyimides were synthesized in N‐methyl‐2‐pyrrolidone (NMP) to prepare polyimide (PI) solutions with various concentrations, and gels can form in PI/NMP solution with a suitable concentration or at a low temperature. Gel–sol transition in the PI/NMP solution has been investigated through a combination of polarized optical microscope, differential scanning calorimeter measurement, and rheological measurements. According to Winter–Chambon theory, the critical gel point is 12 wt %, and the loss tangent (tan δ) shows frequency independence. Gel–sol transition temperature (T_gel) for the 13 wt % solution is around 65 °C. Below the T_gel, the gel exhibits strong optical planar texture, indicating the formation of a fully anisotropic phase, which has a great importance for the fabrication of PI fibers by gel‐spinning. Dynamic temperature sweep measurements show that the formation of the gel from solution is thermoreversible and is significantly delayed in the cooling process. Under the favorable conditions, the tensile strength and modulus of the fibers derived from the solution are about 0.7 and 12.5 GPa using gel‐spinning method, which is believed to afford broad application potential in preparing high‐performance PI fibers. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 450–459     

Amphiphilic diblock copolymer‐based multiagent photonic sensing scheme

Efficient functionalization of polymer optical fibers' (POF) surface by a novel block copolymer material toward the development of low‐cost multiagent sensors is presented. The employed poly(styrene sulfonate‐b‐tert‐butylstyrene) (SPS‐b‐PtBS) diblock copolymer possesses two blocks of distinctively different polarity and charge, the hydrophilic SPS which is sensitive to polar substances and the hydrophobic PtBS which is sensitive to organic solvents. The coexistence of two different blocks allows for the detection of a wide variety of agents, ranging from ammonia, and organic solvents, to biomolecules like lysozyme, at room temperature as opposed to alternative usually more complicated techniques, all with the sole use of one sensing medium. Copolymers' high glass transition temperature enables the formation of stable and environmentally robust overlayers. The sensing performance of the material is evaluated experimentally on the customizable platform of POFs, demonstrating fast response, high operational reversibility, and also reusability in successively different testing agents. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 46–54     

Synthesis of highly refractive and transparent polyimides derived from 4,4′‐thiobis[2″,6″‐dimethyl‐4″‐(p‐phenylenesulfanyl)aniline]

New sulfur‐containing aromatic diamines with methyl groups at the ortho position of amino groups have been developed to prepare highly refractive and transparent aromatic polyimides (PIs) in the visible region. All aromatic PIs derived from 4,4′‐thiobis[2″‐methyl‐4″‐(p‐phenylenesulfanyl)aniline ( 2 ), 4,4′‐thiobis[2,″6″‐dimethyl‐4″‐(p‐phenylenesulfanyl)aniline ( 5 ), and aromatic dianhydride, 4,4′‐[p‐thiobis(phenylenesulfanyl)]diphthalic anhydride ( 6 ) were prepared via a two‐step polycondensation. All PIs showed good thermal properties, such as 10% weight loss temperature in the range of 497–500 °C and glass transition temperatures above 196 °C. In addition, the PIs showed good optical properties, such as optical transparency above 75% at 450 nm with a 10‐μm film thickness, high refractive indices ranging from 1.7135 to 1.7301, and small in‐plane/out‐of‐plane birefringences between 0.0066 and 0.0076. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 656–662, 2010     

Preparation and characterization of biodegradable poly(trimethylenecarbonate‐ε‐caprolactone)‐block‐poly(p‐dioxanone) copolymers

A series of poly(trimethylenecarbonate‐ε‐caprolactone)‐block‐poly(p‐dioxanone) copolymers were prepared with varying feed rations by using two step polymerization reactions. Poly(trimethylenecarbonate)(ε‐caprolactone) random copolymer was synthesized with stannous‐2‐ethylhexanoate and followed by adding p‐dioxanone monomer as the other block. The ring opening polymerization was carried out at high temperature and long reaction time to get high molecular weight polymers. The monofilament fibers were obtained using conventional melting spun methods. The copolymers were identified by ¹H and ¹³C NMR spectroscopy and gel permeation chromatography (GPC). The physicochemical properties, such as viscosity, molecular weight, melting point, glass transition temperature, and crystallinity, were studied. The hydrolytic degradation of copolymers was studied in a phosphate buffer solution, pH = 7.2, 37 °C, and a biological absorbable test was performed in rats. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2790–2799, 2005     

Annealing behavior of gel‐spun polyethylene fibers at temperatures lower than needed for significant shrinkage

The annealing at 373 K of ultrastrong, gel‐spun polyethylene (PE) has been studied. At this temperature, the fibers show no significant shrinkage. Still, a significant decrease in the mechanical properties is observed. The fibers have been analyzed with differential scanning calorimetry (DSC), temperature‐modulated differential scanning calorimetry (TMDSC), atomic force microscopy (AFM), and small‐angle X‐ray scattering (SAXS). During the annealing, the glass transition of the intermediate phase is exceeded, as shown by DSC. When split for structure analysis by AFM, the annealed fibers undergo plastic deformation around the base fibrils instead of brittle fracture. The quasi‐isothermal TMDSC experiments are compared to the minor structural changes seen with SAXS and AFM. The loss of performance of the PE fibers at 373 K is suggested to be caused by the oriented intermediate phase, and not by major changes in the structure or morphology. The overall metastable, semicrystalline structure is shown by TMDSC to posses local regions that can melt reversibly. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 403–417, 2003     

Linear and branched fluoroazo‐benzene chromophores with increased compatibility in semifluorinated polymers

A family of fluorinated azobenzene‐based push‐pull chromophores with one, two, and three trifluorovinyl ether (TFV) groups in linear and branched architecture was synthesized and utilized as active materials in the low optical loss electro‐optic (EO) composites. The fluorinated azobenzene chromophores exhibited increased solubility (30–50 wt %) in semifluorinated polymer host, such as perfluorocyclobutane (PFCB) aromatic ether resin after crosslinking, compared with the commercially available nonfluorinated azobenzene chromophore Disperse Red 1 (1–2 wt %). The impact of this approach on the optical properties on the polymer blends is assessed through optical propagation loss measurements and EO characterization. The resulting fluorinated EO composites showed excellent optical clarity, low birefringence, and low optical loss less than 0.5 dB/cm, while giving EO coefficients of about 3–7 pm/V at 1550 nm. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3166–3177, 2007     

Small‐angle X‐ray scattering investigation of carbon nanotube‐reinforced polyacrylonitrile fibers during deformation

Structural changes during deformation in solution‐ and gel‐spun polyacrylonitrile (PAN) fibers with multi‐ and single‐wall carbon nanotubes (CNTs), and vapor‐grown carbon nanofibers were investigated using synchrotron X‐ray scattering. Previously published wide‐angle X‐ray scattering (WAXS) results showed that CNTs deform under load, alter the response of the PAN matrix to stress, and thus enhance the performance of the composite. In this article, we find that the elongated scattering entities that give rise to the small‐angle X‐ray scattering (SAXS) in solution‐spun fibers are the diffuse matrix‐void interfaces that follow the Porod's law, and in gel‐spun fibers these are similar to fractals. The observed smaller fraction of voids in the gel‐spun fibers accounts for the significant increase in the strength of this fiber. The degree of orientation of the surfaces of the voids is in complete agreement with those of the crystalline domains observed in WAXS, and increases reversibly upon stretching in the same way as those of the crystalline domains indicating that the voids are integral parts of the polymer matrix and are surrounded by the crystalline domains in the fibrils. The solution‐spun composite fibers have a larger fraction of the smaller (<10 nm) voids than the corresponding control PAN fibers. Furthermore, the size distribution of the voids during elongation changes greatly in the solution spun PAN fiber, but not so in its composites. The scattered intensity, and therefore the volume fraction of the voids, decreases considerably above the glass transition temperature (T_g) of polymer. Implications of these observations on the interactions between the nanotubes and the polymer are discussed. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2394–2409, 2009     

Effect of treatment on the thermal conductivity and thermal diffusivity of oil‐palm‐fiber‐reinforced phenolformaldehyde composites

The thermal conductivity and thermal diffusivity of oil‐palm‐fiber‐reinforced untreated (Sample 1) and differently treated composites were measured with the transient plane source technique at room temperature and under normal pressure. All the composites were 40% oil‐palm fiber by weight. The fibers were treated with alkali (Composite 2), silane (Composite 3), and acetic acid (Composite 4) and reinforced in a phenolformaldehyde matrix. The thermal conductivity and thermal diffusivity of the composites increased after treatment to different extents. The thermal conductivity of the treated fibers as well as of the untreated fibers was calculated theoretically. The model results show that the thermal conductivity of the untreated fiber was smaller than the thermal conductivity of the treated fibers. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 916–921, 2000     

Synthesis and polymerization of a new nitrogen‐containing bis‐ortho‐diynylarene monomer

This study focuses on the preparation, characterization, and optical properties of new bis(3,4‐diphenylethynylphenyl)phenylamine. This is the first nitrogen‐containing bis‐ortho‐diynylarene (BODA) monomer having a nitrogen atom as the spacer group. BODA monomers are usually prepared from common bisphenols, thereby providing great synthetic versatility and the opportunity to develop a wide array of novel polyarylene thermosets by varying the aromatic spacer group. The new bis(3,4‐bisphenylethynylphenyl)phenylamine was synthesized in five steps. This compound emits an intense blue color (λ = 438 nm) upon irradiation by UV light and may be suitable for use as an emitting layer in electroluminescent devices. Bis‐(3,4‐bisphenylethynylphenyl)phenylamine and its polymer have photoluminescence quantum yields 34 and 38%, respectively, and long excited‐state lifetimes of 3.2 and 3.6 ns, respectively. The structure of the monomer and its polymer were characterized using spectroscopic techniques including Ultraviolet–visible Spectrophotometer, Photoluminescence Spectrophotometer, Fourier Transform infrared spectroscopy, and Gel Permeation Chromatography. The polymerizations were studied by Differential Scanning Calorimeter. The amount of weight loss and the thermostability of the nitrogen‐containing polymer were determined from thermogravimetric analysis. The electrical conductivity of neat HCl‐doped BODA‐derived polymer film was measured according to the standard four‐point probe technique. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6988–6996, 2006     

Synthesis and properties of copolymers of methyl methacrylate with 2,3,4,5,6‐pentafluoro and 4‐trifluoromethyl 2,3,5,6‐tetrafluoro styrenes: An intrachain interaction between methyl ester and fluoro aromatic moieties

2,3,4,5,6‐Pentafluoro and 4‐trifluoromethyl 2,3,5,6‐tetrafluoro styrenes were readily copolymerized with methyl methacrylate (MMA) by a free radical initiator. The copolymers were soluble in tetrahydrofuran and acetone. The films obtained were transparent and flexible. The glass transition temperatures (T_gs) of the copolymers were found positively deviated from the Gordon–Taylor equation. The positive deviation could be accounted for by dipole–dipole intrachain interaction between the methyl ester group of MMA and the highly fluorinated aromatic moiety, which resulted in a decrease in the segmental mobility of the polymer chains and the enhanced T_g values of the copolymers. The water absorption of PMMA was greatly decreased by copolymerization of MMA with the highly fluorinated styrenes. With as little as 10 mol % of pentafluoro styrene content in the copolymer, the water absorption was decreased to one‐third of that for pure PMMA. The fluorinated styrenes‐MMA copolymers were thermally stable up to 420 °C under air and nitrogen atmospheres. With 50 mol % of MMA in the copolymer, the copolymer was still stable up to 350 °C. Since these copolymers contain a large number of fluorine atoms, the light absorption in the region of the visible to near infrared is decreased in comparison with nonfluorinated polymers. Thus, these copolymers may be suitable for application in optical devices, such as optical fibers and waveguides. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010