Morphosynthesis of poly[4‐(1,4‐phenylene)oxyphthalimide] and copolymers prepared by reaction‐induced crystallization during polymerization

Morphosynthesis of poly[4‐(1,4‐phenylene)oxyphthalimide] (POPI) and poly[4‐(1,4‐phenylene)oxyphthalimide‐co‐4‐phthalimide] (POPI‐PPI) was examined by using the crystallization during the polymerization. The POPI fibrillar crystals were obtained as precipitates with the formation of spherical aggregates of plate‐like crystals. Some of the POPI fibrillar crystals were longer than 15 μm. They possessed high crystallinity and the molecules aligned perpendicular to the long direction of the fibers. On the other hand, one‐dimensional structures of POPI‐PPI such as ribbon, cone, rod, and fiber were obtained as precipitates by the copolymerization. The copolymer molecules might align along the long direction of the cone‐like crystals. The morphology of these poly(ether‐imide)s could be controlled by not only the polymerization condition but also with the aid of copolymerization. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Novel network morphology of poly(p‐oxybenzoyl)

Polymerization of 4‐acetoxybenzoic acid (ABA) with 3,5‐diacetoxybenzoic acid (DABA) was examined to control the morphology of poly(p‐oxybenzoyl) (POB). Polymerizations were carried out at a concentration of 1.0% in an aromatic solvent Therm S‐1000® (mixture of dibenzyltoluene) at 320 °C. Polymerization of ABA yielded the POB fibrillar crystals, but the polymerization with DABA at a concentration in the feed (χ_f) of 0.10–0.15 afforded novel network structures comprised of spheres connected by fibrillar crystals. The diameter of the spheres prepared at χ_f of 0.15, which were 0.7 and 5.0 μm, showed bimodality. The network distance, fibril length, and fibril width were 6.1, 2.6, and 0.1 μm, respectively. They possessed high crystallinity. The network structure was formed as follows. Co‐oligomers were first precipitated in the beginning of the polymerization by liquid–liquid phase separation to form the microdroplets. The fibrillar crystals were formed in the coalesced spheres by the crystallization of oligomers induced by the increase of molecular weight. The fibrillar crystals connecting the spheres gradually appeared owing to the shrinkage of the spheres. The fibrillar crystals grew from the surface of the spheres with the crystallization of homo‐oligomers of 4‐oxybenzoyl units, and finally the network structure was completed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1624–1634, 2005     

A new route of manipulation of poly(L‐lactic acid) crystallization by self‐assembly of p‐tert‐butylcalix[8]arene and toluene

A novel nucleating agent (TBC8‐t), self‐assembled with p‐tert‐butylcalix[8]arene (TBC8) and toluene, was used to manipulate the crystallization behavior of poly(L ‐lactic acid) (PLLA). Toluene molecules were used to adjust the crystallization structure of TBC8. Differential scanning calorimetry results show that the crystallization peak temperature (T_c) and crystallization rate (ΔH_c/time) of PLLA nucleated with TBC8‐t are 132.3 °C and 0.24 J/gs, respectively, which are much higher than that with conventional nucleating agent‐talc (T_c = 119.3 °C, ΔH_c/time = 0.13 J/gs). The results of polarized optical microscopy demonstrate that TBC8‐t could greatly enhance the crystallization rate of PLLA by increasing the nucleation rate rather than crystal growth rate. Along with an improvement of the crystallization rate, the crystalline morphology of PLLA is also affected by TBC8‐t. The addition of TBC8‐t transforms most of the original spherulite crystals into sheaf‐like crystals. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1235–1243, 2010     

Relaxation of shish‐kebab precursor in isotactic polystyrene after short‐term shear flow

We studied the formation and relaxation of precursors of shish‐kebab in isotactic polystyrene after applying pulse shear flow at temperatures above the nominal melting temperatures T_m (=223 °C). It was found that the string‐like objects that were assigned to precursors in a previous article appeared in micrometer scale up to ～285 °C, which was very close to the equilibrium melting temperature T (=289 °C), and the length and the diameter showed two‐step decays consisting of the fast and slow (almost nondecaying) components below ～270 °C, whereas the slow component disappeared above ～270 °C, suggesting that some mechanism stabilizing the string‐like objects disappeared at ～270 °C. It was also found that the two‐step decay was a nature of a single string‐like object, but not an average nature of many precursors, showing heterogeneous inner structure of the precursor. We discussed a possibility that the string‐like object had a fringed micelle type structure including large crystals with a melting temperature of ～270 °C. Within the proposed picture, the highest temperature for the precursor formation (～285 °C) was explained as a melting of the large crystals in oriented melt. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Crystallization behavior of isotactic propylene‐1‐hexene random copolymer revealed by time‐resolved SAXS/WAXD techniques

The crystallization behavior of isotactic propylene‐1‐hexene (PH) random copolymer having 5.7% mole fraction of hexene content was investigated using simultaneous time‐resolved small‐angle X‐ray scattering (SAXS) and wide‐angle X‐ray diffraction (WAXD) techniques. For this copolymer, the hexene component cannot be incorporated into the unit cell structure of isotactic polypropylene (iPP). Only α‐phase crystal form of iPP was observed when samples were melt crystallized at temperatures of 40 °C, 60 °C, 80 °C, and 100 °C. Comprehensive analysis of SAXS and WAXD profiles indicated that the crystalline morphology is correlated with crystallization temperature. At high temperatures (e.g., 100 °C) the dominant morphology is the lamellar structure; while at low temperatures (e.g., 40 °C) only highly disordered small crystal blocks can be formed. These morphologies are kinetically controlled. Under a small degree of supercooling (the corresponding iPP crystallization rate is slow), a segmental segregation between iPP and hexene components probably takes place, leading to the formation of iPP lamellar crystals with a higher degree of order. In contrast, under a large degree of supercooling (the corresponding iPP crystallization rate is fast), defective small crystal blocks are favored due to the large thermodynamic driving force and low chain mobility. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 26–32, 2010     

Molecular composites composed of castor oil‐modified poly(ε‐caprolactone) and self‐assembled hydroxystearic acid fibers

After (R)‐12‐hydroxystearic acid (HSA) was mixed at 100 °C with the castor oil‐modified poly(ε‐caprolactone) (CO‐PCL) prepared by the ring‐opening polymerization of ε‐caprolactone in the presence of castor oil, the mixture was gradually cooled to room temperature to give a solidified CO‐PCL/HSA composite. The CO‐PCL/HSA sample showed an exothermic peak at around 67–71 °C which was lower than the melting point of HSA (76.8 °C), indicating the formation of mesogenic HSA aggregates. The rheological measurement of the CO‐PCL/HSA revealed the formation of HSA organogel at around 67–55 °C during the cooling process from the melt. Furthermore, the polarized and normal optical microscopic analyses of CO‐PCL/HSA on the cooling stage revealed that anisotropic fibrous materials are formed at around 60 °C and then the fibrous network propagated over the matrix polymer. The flexural modulus and storage modulus of the CO‐PCL/HSA composite increased with increasing HSA content. The CO‐PCL/HSA composite annealed at 60 °C for 2 h on the cooling process had a higher flexural and storage modulus than the sample without annealing. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1281–1289, 2010     

Preparation of poly(p‐oxybenzoyl) crystals using direct polymerization of p‐hydroxybenzoic acid in the presence of boronic anhydrides

Poly(p‐oxybenzoyl) (POB) crystals were prepared by reaction‐induced crystallization during direct polymerization of p‐hydroxybenzoic acid in the presence of boronic anhydrides. Polymerizations were carried out at 300 °C in dibenzyltoluene at a concentration of 1% with three kinds of anhydrides of boronic acid such as 3,4,5‐trifluorophenylboronic acid (TFB), 4‐methoxyphenylboronic acid (MPB) and 4‐biphenylboronic acid (BPB). The POB crystals were formed as precipitates in the solution and the morphology was considerably influenced by both the structure of the boronic anhydride and its concentration (c_B). Needle‐like crystals were firmed in the presence of TFB anhydride (TFBA) at c_Bs of 5 and 10 mol % by the spiral growth of lamellae. Spherical aggregates of slab‐like crystals were formed at c_Bs from 50 to 100 mol %. The polymerization with MPB anhydride and BPB anhydride (BPBA) also yielded the needle‐like crystals at c_Bs of 50 and 5 mol %, respectively. The polymerization with TFBA at lower c_B was favorable to prepare the needle‐like crystal. Molecular weight was also influenced by the structure of the boronic anhydride and c_B. M_n increased generally with c_B and BPBA gave the highest M_n of 14.7 × 10³ at c_B of 100 mol %. The loose packing of the molecules in the crystal caused by the bulkiness of the end‐groups made the polymerization in the crystals more efficiently. Morphology and molecular weight of the POB crystals could be controlled by the chemical structure and the content of boronic anhydride. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Melt crystallization and morphology of poly(ε‐caprolactone)‐poly(ethylene glycol) diblock copolymers with different compositions and molecular weights

Ring opening polymerization of ε‐caprolactone was realized in the presence of monomethoxy poly(ethylene glycol) with M_n = 1000 and 2000, using Zn(La)₂ as catalyst. The resulting PCL‐PEG diblock copolymers with CL/EO repeat unit molar ratios from 0.2 to 3.0 were characterized by using DSC, WAXD, SEC, and ¹H NMR. The crystal phase of PCL blocks exist in all polymers, and the crystallization ability of PCL blocks increases with CL/EO ratio. PEG blocks are able to crystallize for copolymers with CL/EO below 1.0 only. Melt crystallization results were analyzed with Avrami equation. The Averami exponent n is around 3.0 in most cases, in agreement with heterogeneous nucleation with three dimensional growth. The morphology of the crystals was observed by using POM. Rod‐like crystals were found to grow in 1, 3 or 2, 4 quadrants for samples with low molecular weights. In the case of a copolymer with M_n,PEG = 2000 and M_n,PCL = 800, PEG blocks could crystallize and grow on PCL crystals after PCL finished to form rod‐like crystals, leading to formation of poorly or well structured spherulites. The spherulite growth rate (G) was determined at different crystallization temperatures (T_c) ranging from 9 to 49 °C. All the copolymers present a steady G decrease with increasing crystallization temperature due to lower undercooling. On the other hand, increase of CL/EO ratio leads to increase of G in the same T_c range. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 286–293, 2010     

Preparation of single‐walled carbon nanotubes‐induced poly(p‐oxybenzoyl) crystals

Crystallization of oligomers was applied for the preparation of single‐walled carbon nanotubes (SWNTs)/poly(p‐oxybenzoyl) (POB) crystals using SWNTs as a nucleating agent. Polymerization conditions were investigated to induce the crystallization of POB oligomers through SWNTs. SWNTs/POB plate‐like or lozenge‐shaped crystals were successfully prepared by direct polymerization of p‐hydroxybenzoic acid (HBA) in a mixed solvent of DMF/Py with TsCl in the presence of functionalized SWNTs. The size of the plate‐like crystals were ～200 nm to 3 μm. The crystals consisted of some layers, ～3 nm thick plates. Model reactions showed that esterification reactions proceed between functionalized SWNTs and HBA monomers in the polymerization system. The obtained crystals exhibited unique morphology and high crystallinity, producing a novel SWNT/POB hybrid. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1265–1277, 2008     

Relevance of a prereaction for the in situ NMP of styrene using the C‐Phenyl‐N‐tert‐butylnitrone/2,2′‐azobis(isobutyronitrile) pair

In this article, we compare two routes for carrying out in situ nitroxide‐mediated polymerization of styrene using the C‐phenyl‐N‐tert‐butylnitrone (PBN)/2,2′‐azobis(isobutyronitrile) (AIBN) pair to identify the best one for an optimal control. One route consists in adding PBN to the radical polymerization of styrene, while the other approach deals with a prereaction between the nitrone and the free radical initiator prior to the addition of the monomer and the polymerization. The combination of ESR and kinetics studies allowed demonstrating that when the polymerization of styrene is initiated by AIBN in the presence of enough PBN at 110 °C, fast decomposition of AIBN is responsible for the accumulation of dead polymer chains at the early stages of the polymerization, in combination with controlled polystyrene chains. On the other hand, PBN acts as a terminating agent at 70 °C with the formation of a polystyrene end‐capped by an alkoxyamine, which is not labile at this temperature but that can be reactivated and chain‐extended by increasing the temperature. Finally, the radical polymerization of styrene is better controlled when the nitrone/initiator pair is prereacted at 85 °C for 4 h in toluene before styrene is added and polymerized at 110 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1085–1097, 2009     

Thermal stability of porous it‐PMMA thin film obtained by the extraction of st‐PMAA from it‐PMMA/st‐PMAA stereocomplex with layer‐by‐layer assembly on a substrate

The functionality of porous isotactic (it) poly(methyl methacrylate) (PMMA) thin films, which were previously developed by the selective extraction of syndiotactic (st) poly(methacrylic acid) (PMAA) from the it‐PMMA/st‐PMAA stereocomplex thin film on a substrate using the layer‐by‐layer assembly method was investigated after thermal treatment (70, 80, and 90 °C) in water for 4 h. Quartz crystal microbalance analysis and infrared spectra measurements revealed that the st‐PMAA incorporation ability of the porous it‐PMMA thin film decreased in order at 80 and 90 °C, while there was no decrease observed at 70 °C. X‐ray diffraction analysis also supported the thermal stability of the porosity at 70 °C, whereas two it‐PMMA crystalline peaks (2θ = 9° and 14°) were generated during heating at 90 °C. The loss of the functionality of the it‐PMMA thin film was thus shown to be due to crystallization, which was caused by the increase in polymer‐chain mobility during the heating process. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3265–3270, 2010     

Anionic polymerization of N,N‐dialkyl‐2‐methylenebut‐3‐enamide: Effect of alkyl substituents on polymerization behavior

Anionic polymerizations of three 1,3‐butadiene derivatives containing different N,N‐dialkyl amide functions, N,N‐diisopropylamide (DiPA), piperidineamide (PiA), and cis‐2,6‐dimethylpiperidineamide (DMPA) were performed under various conditions, and their polymerization behavior was compared with that of N,N‐diethylamide analogue (DEA), which was previously reported. When polymerization of DiPA was performed at ?78 °C with potassium counter ion, only trace amounts of oligomers were formed, whereas polymers with a narrow molecular weight distribution were obtained in moderate yield when DiPA was polymerized at 0 °C in the presence of LiCl. Decrease in molecular weight and broadening of molecular weight distribution were observed when polymerization was performed at a higher temperature of 20 °C, presumably because of the effect of ceiling temperature. In the case of DMPA, no polymer was formed at 0 °C and polymers with relatively broad molecular weight distributions (M_w/M_n = 1.2) were obtained at 20 °C. The polymerization rate of PiA was much faster than that of the other monomers, and poly(PiA) was obtained in high yield even at ?78 °C in 24 h. The microstructure of the resulting polymers were exclusively 1,4‐ for poly(DMPA), whereas 20–30% of the 1,2‐structure was contained in poly(DiPA) and poly(PiA). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3714–3721, 2010     

Poly(bis‐2,2,2‐trifluoroethoxymethyl oxetane): Multiple crystal phases,crystallization‐induced surface topological complexity and enhanced hydrophobicity

Semicrystalline poly(bis‐trifluoroethoxymethyl)oxetane, P(B‐3FOx), was prepared by cationic ring‐opening polymerization at ?5 °C with M_n up to 21 kDa. Differences in cooling rates from the melt have substantial effects on crystal phase, percent crystallinity, surface topography, and wetting behavior. DSC and WAXD show that cooling from the melt at slow rates (<5 °C/min) gives α‐P(B‐3FOx) with ΔH_f = 22–27 J/g. Quenching from the melt results in β‐P(B‐3FOx) for which a mesophase structure is suggested. β‐P(B‐3FOx) melts at 53 °C followed by recrystallization to α‐P(B‐3FOx). Solution casting from THF results in third phase, γ‐P(B‐3FOx). TM‐AFM and SEM imaging for α‐P(B‐3FOx) showed that cold crystallization at 25 °C brought about increased crystallinity and surface topologies characterized by sharp asperities and lath‐shaped crystals. Spontaneous surface roughening of α‐P(B‐3FOx) results in a discontinuous three‐phase contact line with water and an increase in water sessile drop contact angle from 106° to 136°. The ～30° increase in water contact angle was attributed primarily to a topological change from a relatively smooth surface (Wenzel state) to an asperity‐rich surface yielding a discontinuous three‐phase contact line (composite of Wenzel and Cassie‐Baxter state). The oleophobicity for this polymer, which contains only a single ? CF₃ end group on each side chain, compares favorably with more highly fluorinated acrylates. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1022–1034, 2010     

Melt‐processable poly(oxyphenylalkanoate): Synthesis,properties, and in vitro degradation of poly(4‐oxyphenylacetate)

The homopolyester of 4‐hydroxyphenylacetic acid (HPAA) was synthesized by one‐pot, slurry‐melt, and acidolysis melt polymerization techniques and was characterized by its inherent viscosity and IR and NMR spectra. Differential scanning calorimetry (DSC), polarizing light microscopy (PLM), and wide‐angle X‐ray diffraction (WAXD) studies of the homopolymer were carried out for its thermal and phase behavior. The results indicated that the yield and molecular weight of the polymer depended on the method of preparation; moreover, the acidolysis melt polymerization of the pure acetoxy derivative of HPAA was the best method for the preparation of high molecular weight poly(4‐oxyphenylacetate) (polyHPAA) without side reactions. DSC and PLM studies also showed that the thermal and optical properties depended largely on the polymerization conditions and inherent viscosity values. PolyHPAA did not show a clear texture typical of liquid‐crystalline polymers, whereas after cooling from the melt, structures similar to spherulitic crystals were observed. WAXD patterns showed a crystalline nature. The in vitro degradability of the polymer was also studied via the water absorption in buffer solutions of pH 7 and 10 at 30 and 60 °C; this was followed by Fourier transform infrared, inherent viscosity, DSC, thermogravimetric analysis, WAXD, and scanning electron microscopy techniques. Unlike Vectra®, which showed no degradation, polyHPAA showed an increase in hydrolytic degradation from 5.0 and 6.0% at 30 °C to 12.5 and 15.0% at 60 °C after 350 h in buffer solutions of pH 7 and 10, respectively. The results indicated a possible biomedical prosthetic application of poly(oxyphenylalkanoate)s such as polyHPAA with better crystallinity coupled with degradability as a substitute for poly(hydroxyalkanoates). © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2430–2443, 2001     

Nonisothermal crystallization kinetics of poly(ε‐caprolactone) blocks in double crystalline triblock copolymers containing poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) and poly(ε‐caprolactone) units

The poly(3‐hydroxbutyrate‐co‐3‐hydroxyvalerate)/poly(ε‐caprolactone) block copolymers (PHCLs) with three different weight ratios of PCL blocks (38%, named PHCL‐38; 53%, named PHCL‐53; and 60%, named PHCL‐60) were synthesized by using PHBV with two hydroxyl end groups to initiate ring‐opening polymerization of ε‐caprolactone. During DSC cooling process, melt crystallization of PHCL‐53 at relatively high cooling rates (9, 12, and 15 °C min^?1) and PHCL‐60 at all the selected cooling rates corresponded to PCL blocks so that PHCL‐53 and PHCL‐60 were used to study the nonisothermal crystallization behaviors of PCL blocks. The kinetics of PCL blocks in PHCL‐53 and PHCL‐60 under nonisothermal crystallization conditions were analyzed by Mo equation. Mo equation was successful in describing the nonisothermal crystallization kinetics of PCL blocks in PHCLs. Crystallization activation energy were estimated using Kissinger's method. The results of kinetic parameters showed that both blocks crystallized more difficultly than corresponding homopolymers. With the increase of PCL content, the crystallization rate of PCL block increased gradually. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Copper(0)‐mediated living radical polymerization of acrylonitrile at room temperature

The copper(0)‐catalyzed living radical polymerization of acrylonitrile (AN) was investigated using ethyl 2‐bromoisobutyrate as an initiator and 2,2′‐bipyridine as a ligand. The polymerization proceeded smoothly in dimethyl sulphoxide with higher than 90% conversion in 13 h at 25 °C. The polymerization kept the features of controlled radical polymerization. ¹H NMR spectra proved that the resultant polymer was end‐capped by ethyl 2‐bromoisobutyrate species. Such polymerization technique was also successfully introduced to conduct the copolymerization of styrene (St) and AN to obtain well‐controlled copolymers of St and AN at 25 °C, in which the monomer conversion of St could reach to higher than 90%. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Nonstoichiometric polycondensation of 4‐acetoxybenzoic acid in the presence of monoacetate

Nonstoichiometric polycondensation of 4‐acetoxybenzoic acid (ABA) was examined in the presence of three kinds of aromatic monoacetates: 4‐hexyloxyphenyl acetate, 4‐decyloxyphenyl acetate, and 4‐octadecyloxyphenyl acetate. Polymerizations were carried out in liquid paraffin at 320 °C under nonstoichiometric conditions, in which the acetoxy group was in large excess of the carboxyl group. Poly(4‐oxybenzoyl) (POB) was obtained as crystal at the molar ratio of monoacetates in feed (χ) of less than 80 mol %, meaning that the concentration of the acetoxy group was five times that of the carboxylic group. The obtained POB possessed much higher number average degree of polymerization (DP_n), ranging from 353 to 467, than the calculated DP_n on the basis of χ. High molecular weight polymer was synthesized even under nonstoichiometric conditions via crystallization of oligomers and the following solid‐state polymerization in the crystals. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1757–1766, 2005     

Some novel accelerating agents for nitroxide‐mediated living free‐radical polymerization

Malononitrile (MN), trifluoroacetic acid anhydride, acetylacetone, acetoacetic ester, and diethyl malonate have been identified as novel rate‐accelerating additives for nitroxide‐mediated living free‐radical polymerization. Among these additives, MN has the greatest accelerating effect. Adding MN at an MN/2,2,6,6‐tetramethylpiperidine‐oxyl (TEMPO) molar ratio of 4.0 results in a nearly 20 times higher rate of polymerization of styrene (St), and adding MN at an MN/TEMPO molar ratio of 2.5 results in a nearly 15 times higher rate of copolymerization of St and methyl methacrylate. The polymerization of St proceeds in a living fashion, as indicated by the increase in the molecular weight with time and conversion and the relatively low polydispersity. The polymerization rate of St is so quick that the conversion reaches 70% within 1 h at 125 °C when the molar ratio of MN to TEMPO is 4:1. Moreover, the reaction temperature can be reduced to 110 °C. A possible explanation for this effect is that the formation of hydrogen bonds between the MN and TEMPO moiety weakens the C? ON bond at the end of the polymer chain. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5246–5256, 2005     

Stereocomplex formation between enantiomeric poly(α‐methyl‐α‐ethyl‐β‐propiolactones): Effect of molecular weight

Optically pure S(?) and R(+)‐poly(α‐methyl‐α‐ethyl‐β‐propiolactones) (PMEPLs) of controlled low molecular weights were synthesized by anionic polymerization of the corresponding optically active monomers, and characterized using gel permeation chromatography, Maldi‐TOF mass spectrometry, and NMR spectroscopy. Blends of PMEPLs of opposite configurations and different molecular weights were investigated. All blends lead to the formation of a stereocomplex and its crystallization prevails over a wide range of mixing ratios. The stereocomplex melts 30–40 °C above that of the corresponding pure polymers, depending on the molecular weight; pairs of polymers having similar molecular weights exhibit the highest melting temperatures and enthalpies of fusion. Finally, when the stereocomplex is dispersed in a PMEPL matrix, it acts as a very effective nucleation agent for the crystallization of the polymer in excess. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2380–2389, 2007     

Effects of filler size and heat treatment on the crystallization behavior of glass bead‐filled polypropylene

The effects of glass bead (GB) size and annealing temperature on the formation of β‐crystals of glass bead‐filled polypropylene (PP) are studied in this articles. Differential scanning calorimetry (DSC) measurements indicated that the amount of β‐form in PP crystals was a function of the glass bead content and size. For a fixed glass bead content, it was found that the smaller the diameter of the glass bead, the higher was the content of β‐crystals formed in the PP. On the other hand, wide‐angle X‐ray diffraction (WAXD) measurements revealed that the annealing temperature was also a major factor that affected the crystallization behavior of glass bead‐filled PP. It seemed that the blends with different glass bead contents had their own optimal annealing temperatures for β‐crystal formation. As an example, when the glass bead content was 48 wt %, the optimal annealing temperature for β‐crystal formation was about 108 °C, whereas it shifted to 100 °C for 14 wt % glass bead‐filled polypropylene. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 306–313, 2005