Toward low‐band gap dithienophosphole copolymers for an application in organic solar cells

Two functionalized dithieno[3,2‐b:2′,3′‐d]phospholes with solubilizing groups have been synthesized that allow for the generation of a series of π‐conjugated AB‐ and ABC‐copolymers. The polymers obtained show notable optoelectronic properties with red‐shifted absorption and emission in the orange to red section of the optical solar spectrum. Although combination of dithienophosphole units with fluorene building blocks gives access to processable polymers with band gaps between 2.2 and 2.3 eV in solution and 2.0 eV in the solid state, an ABC copolymer based on dithienophosphole, fluorene, and bis(thienyl)benzothiadiazole units was found to not only exhibit a suitable band gap for solar cell applications (solution: 2.0 eV; solid state: 1.7 eV) but also showed good solubility as well as good electron transfer properties in the presence of fullerene (C₆₀). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8179–8190, 2008     

Regioregular poly[3‐(4‐alkoxyphenyl)thiophene]s

An easy synthetic procedure for soluble poly[3‐(4‐alcoxyphenyl)thiophene]s is reported. The polymers present a high regioregularity degree as determined by both UV–vis spectra and ¹H and ¹³C NMR analysis. Furthermore, X‐ray powder diffraction analysis performed on films of the polymers suggests a π‐stacked packing structure of the macromolecules. Electrical characterization was performed on one of the synthesized polythiophenes on both undoped and doped (with FeCl₃ or iodine) films. The conductivity and charge‐carrier mobility were assessed by current–voltage and field effect measurements. Well‐structured polymer films were obtained simply via spin coating from chloroform solutions and without the need of further processing, unlike other regioregular polythiophenes reported in the literature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1758–1770, 2007     

Syntheses and optoelectronic properties of quinoxaline polymers: The effect of donor unit

Tuning the bandgap of electrochromic polymers is one of the important research topics in electrochromism. To understand clearly the effect of donor unit in donor–acceptor–donor‐type polymers, 2,3‐bis(4‐tert‐butylphenyl)‐5,8‐di(thiophen‐2‐yl)quinoxaline and 2,3‐bis(4‐tert‐butylphenyl)‐5‐(2,3‐dihydrothieno[3,4‐b][1,4]dioxin‐ 5‐yl)‐8‐(thiophen‐2‐yl)quinoxaline were synthesized and polymerized potentiodynamically. Their electrochemical and spectroelectrochemical studies were performed, and the results were compared with those of poly(2,3‐bis(4‐tert‐butylphenyl)‐5,8‐bis(2,3‐dihydrothieno[3,4‐b][1,4]dioxin‐5‐yl)quinoxaline) (Gunbas et al., Adv Mater 2008, 20, 691–695). A blue shift in the polymer π–π* transitions revealed that the bandgap of such polymers with the same acceptor unit is related to the electron density of donor units. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and electrochromic properties of triphenylamine containing copolymers: Effect of π‐bridge on electrochemical properties

In this study, a series of benzotriazole (BTz) and triphenylamine (TPA)‐based random copolymers; poly4‐(5‐(2‐dodecyl‐7‐methyl‐2H‐benzo[d][1,2,3]triazol‐4‐yl)thiophen‐2‐yl)‐N‐(4‐(5‐methylthiophen‐2‐yl)phenyl)‐N‐phenylaniline ( P1 ), poly4′‐(2‐dodecyl‐7‐methyl‐2H‐benzo[d][1,2,3]triazol‐4‐yl)‐N‐(4′‐methyl‐[1,1′‐biphenyl]‐4‐yl)‐N‐phenyl‐[1,1′‐biphenyl]‐4‐amine ( P2 ), and poly4‐(5′‐(2‐dodecyl‐7‐(5‐methylthiophen‐2‐yl)?2H‐benzo[d][1,2,3]triazol‐4‐yl)‐[2,2′‐bithiophen]‐5‐yl)‐N‐(4‐(5‐methylthiophen‐2‐yl)phenyl)‐N‐phenylaniline ( P3 ) were synthesized to investigate the effect of TPA unit and π‐bridges on electrochemical and spectroelectrochemical properties of corresponding polymers. The synthesis was carried out via Stille coupling for P1 , P3 , and Suzuki coupling for P2 . Electrochemical and spectral results showed that P1 has an ambipolar character, in other words it is both p‐type and n‐type dopable, whereas P2 and P3 have only p‐doping property. Effect of different π‐bridges and TPA unit on the HOMO and LUMO energy levels, switching time, and optical contrast were discussed. All polymers are promising materials for electrochromic devices. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 537–544     

Soluble alkyl substituted poly(3,4‐propylenedioxyselenophene)s: A new platform for optoelectronic materials

Optical and electrochemical properties of regiosymmetric and soluble alkylenedioxyselenophene‐based electrochromic polymers, namely poly(3,3‐dibutyl‐3,4‐dihydro‐2H‐selenopheno[3,4‐b][1,4]dioxephine) (PProDOS‐C₄), poly(3,3‐dihexyl‐3,4‐dihydro‐2H‐selenopheno[3,4‐b][1,4]dioxephine) (PProDOS‐C₆), and poly(3,3‐didecyl‐3,4‐dihydro‐2H‐selenopheno[3,4‐b][1,4]dioxephine) (PProDOS‐C₁₀), are highlighted. It is noted that these unique polymers have low bandgaps (1.57–1.65 eV), and they are exceptionally stable under ambient atmospheric conditions. Polymer films retained 82–97% of their electroactivity after 5000 cycles. The percent transmittance of PProDOS‐C_n (n = 4, 6, 10) films found to be between 55 and 59%. Furthermore, these novel soluble PProDOS‐C_n polymers showed electrochromic behavior: a color change form pure blue to highly transparent state in a low switching time (1.0 s) during oxidation with high coloration efficiencies (328–864 cm² C^?1) when compared to their thiophene analogues. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and photovoltaic properties of thieno[3,4‐b]pyrazine or dithieno[3′,2′:3,4;2″,3″:5,6]benzo[1,2‐d]imidazole‐containing conjugated polymers

Novel conjugated polymers composed of benzo[1,2‐b:4,5‐b′]dithiophene and thieno[3,4‐b]pyrazine or dithieno[3′,2′:3,4;2″,3″:5,6]benzo[1,2‐d]imidazole units are synthesized by Stille polycondensation. The resulting polymers display a longer wavelength absorption and well‐defined redox activities. The effective intramolecular charge‐transfer and energy levels of all polymers are elucidated by computational calculations. Bulk‐heterojunction solar cells based on these polymers as p‐type semiconductors and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) as an n‐type semiconductor are fabricated, and their photovoltaic performances are for the first time evaluated. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1067–1075     

Exhaustive and partial alkoxylation of polymethylhydrosiloxane by copper‐catalyzed dehydrocoupling with alcohols: Synthesis,crosslinking behavior,and thermal properties of the products

Polymethylhydrosiloxane (PMHS) reacts with aliphatic and aromatic alcohols at room temperature in the presence of [CuH(PPh₃)]₆ complex catalyst to give poly[(methyl) (alkoxy)siloxane]s in high yields. Reactivity of alcohols decreases in the order of p‐methoxyphenol > p‐cresol > phenol > benzyl alcohol > allyl alcohol > ethanol > isopropanol > tert‐butyl alcohol. Partially p‐cresylated polymers, which still retain unreacted Si? H bonds, react further with ethylene glycol or water to form cross‐linked polymers, which, depending on the extent of cross linking, gelate during the cross‐linking process. Propargyl alcohol reacts with PMHS very rapidly to give exhaustively and partially propargyloxylated PMHS. Resulting polymers, upon heating, undergo crosslinking. Partially propargyloxylated polymers display high thermal stability [T_d5 (temperature of 5% weight loss) > 500 °C] as compared with starting PMHS (243 °C) and exhaustively propargyloxylated one (414 °C). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of poly(1‐chloro‐2‐arylacetylene)s with high cis‐content and examination of their absorption/emission properties

A series of 1‐chloro‐2‐arylacetylenes [Cl‐C?C‐Ar, Ar = C₆H₅ ( 1 ), C₆H₄‐p‐i Pr ( 2 ), C₆H₄‐p‐Oi Pr ( 3 ), C₆H₄‐p‐NHC(O)Ot Bu ( 4 ), and C₆H₄‐o‐i Pr ( 5 )] were polymerized using (tBu₃P)PdMeCl/silver trifluoromethanesulfonate (AgOTf) and MoCl₅/SnBu₄ catalysts. The corresponding polymers [poly( 1 )–poly( 5 )] with weight‐average molecular weights of 6,500–690,000 were obtained in 10–91% yields. THF‐insoluble parts, presumably high‐molecular weight polymers, were formed together with THF‐soluble polymers by the Pd‐catalyzed polymerization. The Pd catalyst polymerized nonpolar monomers 1 and 2 to give the polymers in yields lower than the Mo catalyst, while the Pd catalyst polymerized polar monomers 3 and 4 to give the corresponding polymers in higher yields. The ¹H NMR and UV–vis absorption spectra of the polymers indicated that the cis‐contents of the Pd‐based polymers were higher than those of the Mo‐based polymers, and the conjugation length of the Pd‐based polymers was shorter than that of the Mo‐based polymers. Pd‐based poly( 5 ) emitted fluorescence most strongly among poly( 1 )–poly( 5 ). © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 382–388     

Synthesis and characterization of novel low‐bandgap triphenylamine‐based conjugated polymers with main‐chain donors and pendent acceptors for organic photovoltaics

A series of novel low‐bandgap triphenylamine‐based conjugated polymers ( PCAZCN , PPTZCN , and PDTPCN ) consisting of different electron‐rich donor main chains (N‐alkyl‐2,7‐carbazole, phenothiazine, and cyclopentadithinopyrol, respectively) as well as cyano‐ and dicyano‐vinyl electron‐acceptor pendants were synthesized and developed for polymer solar cell applications. The polymers covered broad absorption spectra of 400–800 nm with narrow optical bandgaps ranging 1.66–1.72 eV. The highest occupied molecular orbital and lowest unoccupied molecular orbital levels of the polymers measured by cyclic voltammetry were found in the range of ?5.12 to ?5.32 V and ?3.45 to ?3.55 eV, respectively. Under 100 mW/cm² of AM 1.5 white‐light illumination, bulk heterojunction photovoltaic devices composing of an active layer of electron‐donor polymers ( PCAZCN , PPTZCN , and PDTPCN ) blended with electron‐acceptor [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester or [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) in different weight ratios were investigated. The photovoltaic device containing donor PCAZCN and acceptor PC₇₁BM in 1:2 weight ratio showed the highest power conversion efficiency of 1.28%, with V_oc = 0.81 V, J_sc = 4.93 mA/cm², and fill factor = 32.1%. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis of optically active conjugated polymers containing platinum in the main chain: Control of the higher‐order structures by substituents and solvents

The Sonogashira–Hagihara coupling polymerization of d ‐hydroxyphenylglycine‐derived diiodo monomers 1–4 and platinum‐containing diethynyl monomer 5 gave the corresponding polymers [poly( 1–5 )–( 2–5 )] with number‐average molecular weights of 19,000–25,000 quantitatively. The polymers were soluble in CHCl₃, CH₂Cl₂, THF, and DMF. CD and UV–vis spectroscopic analysis revealed that amide‐substituted polymers [poly( 1–5 ) and poly( 2–5 )] formed chiral higher‐order structures in solution, while ester‐substituted polymers [poly( 3–5 ) and poly( 4–5 )] did not. Poly( 1–5 ) formed one‐handed helices in THF/toluene mixtures, while it formed chiral aggregates in THF/MeOH mixtures. Poly( 1–5 ) emitted fluorescence with quantum yields ranging from 0.8 to 1.3%. The polymers usually aggregated in the solid state. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2452–2461     

Benzo[2,1‐b;3,4‐b′]dithiophene‐based low‐bandgap polymers for photovoltaic applications

The synthesis of four alternating copolymers using benzo[2,1‐b;3,4‐b′]dithiophene (BDP) as the common donor unit is presented. Before the synthesis, theoretical calculations that we performed predicted that the incorporation of BDP, which consists of fused dithiophene units with a benzene ring, into these polymers would produce a low‐lying highest occupied molecular orbital (HOMO) energy level. Low‐lying HOMO levels are desirable to produce high open circuit voltages (V_OC) in organic bulk heterojunction (BHJ) photovoltaic devices. The polymers' structural characterization, as well as the preliminary results of their performance in BHJ devices, using (6,6)‐phenyl C₆₁‐butyric acid methyl ester as the electron acceptor, is presented. The V_OC values follow the expected trend: increasing with decreasing HOMO level of the polymer. High V_OC values of 0.81 and 0.82 V have been obtained from two polymers: PBDPBT and PBDPDPP. The initial power conversion efficiency achieved in these unoptimized devices was 1.11% because of relatively low J_SC values. The variation observed in the J_SC values between the four polymers is discussed. Device performance is expected to increase with optimization of processing conditions for the devices. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Thieno[3,2‐b]thiophene‐substituted benzodithiophene in donor–acceptor type semiconducting copolymers: A feasible approach to improve performances of organic photovoltaic cells

Thieno[3,2‐b]thiophene‐substituted benzo[1,2‐b:4,5‐b′]dithiophene donor units (TTBDT) serve as novel promising building blocks for donor–acceptor (D‐A) copolymers in organic photovoltaic cells. In this study, a new D‐A type copolymer (PTTBDT‐TPD) consisting of TTBDT and thieno[3,4‐c]pyrrole‐4,6‐dione (TPD) is synthesized by Stille coupling polymerization. A PTTBDT‐TPD analog consisting of TTBDT and alkylthienyl‐substituted BDT (PTBDT‐TPD) is also synthesized to compare the optical, electrochemical, morphological, and photovoltaic properties of the polymers. Bulk heterojunction photovoltaic devices are fabricated using the polymers as p‐type donors and [6,6]‐phenyl C₇₁‐butyric acid methyl ester (PC₇₁BM) as the n‐type acceptor. The power conversion efficiencies of the devices fabricated using PTTBDT‐TPD and PTBDT‐TPD are 6.03 and 5.44%, respectively. The difference in efficiency is attributed to the broad UV–visible absorption and high crystallinity of PTTBDT‐TPD. The replacement of the alkylthienyl moiety with thieno[3,2‐b]thiophene on BDT can yield broad UV–visible absorption due to extended π‐conjugation, and enhanced molecular ordering and orientation for organic photovoltaic cells. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3608–3616     

Donor–acceptor photovoltaic polymers based on 1,4‐dithienyl‐2,5‐dialkoxybenzene with intramolecular noncovalent interactions

Donor–acceptor (D–A) conjugated polymers bearing non‐covalent configurationally locked backbones have a high potential to be good photovoltaic materials. Since 1,4‐dithienyl‐2,5‐dialkoxybenzene ( TBT ) is a typical moiety possessing intramolecular S…O interactions and thus a restricted planar configuration, it was used in this work as an electron‐donating unit to combine with the following electron‐accepting units: 3‐fluorothieno[3,4‐b]thiophene ( TFT ), thieno‐[3,4‐c]pyrrole‐4,6‐dione ( TPD ), and diketopyrrolopyrrole ( DPP ) for the construction of such D–A conjugated polymers. Therefore, the so‐designed three polymers, PTBTTFT , PTBTTPD , and PTBTDPP , were synthesized and investigated on their basic optoelectronic properties in detail. Moreover, using [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as acceptor material, polymer solar cells (PSCs) were fabricated for studying photovoltaic performances of these polymers. It was found that the optimized PTBTTPD cell gave the best performance with a power conversion efficiency (PCE) of 4.49%, while that of PTBTTFT displayed the poorest one (PCE = 1.96%). The good photovoltaic behaviors of PTBTTPD come from its lowest‐lying energy level of the highest occupied molecular orbital (HOMO) among the three polymers, and good hole mobility and favorable morphology for its PC₇₁BM‐blended film. Although PTBTDPP displayed the widest absorption spectrum, the largest hole mobility, and regular chain packing structure when blended with PC₇₁BM, its unmatched HOMO energy level and disfavored blend film morphology finally limited its solar cell performance to a moderate level (PCE: 3.91%). © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 689–698     

Triphenylamine‐based polyimides with trimethyl substituents for gas separation membrane and electrochromic applications

Two series of polyimides I – II with methyl‐substituted triphenylamine units were prepared from the diamines, 4,4′‐diamino‐2″,4″,6″‐trimethyltriphenylamine (Me₃TPA‐diamine; 1 ) and 4,4′‐diamino‐4″‐methyltriphenylamine (MeTPA‐diamine; 2 ), and two commercially available tetracarboxylic dianhydrides via a conventional two‐step chemical imidization. All the polymers were readily soluble in many polar solvents and showed useful levels of thermal stability associated with high glass transition temperatures (266–340 °C) and high char yields (higher than 49% at 800 °C in nitrogen). The polymer films showed reversible electrochemistry/electrochromism accompanied by a color change from neutral pale yellow to green oxidized form with good coloration efficiency, switching time, and stability. The CO₂ permeability coefficients (P_CO2) and permeability selectivity (P_CO2/P_CH4) for these polyimide membranes were in the range of 34.1–229.2 barrer and 21.3–28.9, respectively. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and electrochromic properties of aromatic polyetherimides based on a triphenylamine‐dietheramine monomer

A series of electroactive polyetherimides (PEIs) with triphenylamine (TPA) units were prepared from the polycondensation reactions of 4,4′‐bis(p‐aminophenoxy)triphenylamine with aromatic tetracarboxylic dianhydrides via a conventional two‐step technique. The PEIs showed high thermal stability, with glass‐transition temperatures of 234–282 °C and decomposition temperatures in excess of 500 °C. They showed well‐defined and reversible redox couples during both p‐ and n‐doping processes, together with multielectrochromic behaviors. These polymers exhibited enhanced redox‐stability and electrochromic performance as compared with the corresponding analogs without the phenoxy spacer between the TPA and imide units. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2925–2938     

The suzuki–heck polymerization as a tool for the straightforward obtainment of poly(fluorenylene‐vinylene) sensitizers for dye‐sensitized solar cells

This article describes the synthesis and properties of the first poly(arylene‐vinylene)‐based sensitizers for application in dye‐sensitized solar cells (DSSC). The polymers were prepared by the Suzuki–Heck copolymerization of potassium vinyltrifluoroborate (PVTB) with a mixture of dibromoaryl comonomers designed to obtain macromolecules able to bind onto the photoelectrode by means of carboxyphenylene units. The copolymerization reactions were carried out in the presence of an excess of PVTB to lower the molecular weights of the polymers, which were obtained as soluble materials. The polymers poly[(9,9‐didodecyl‐2,7‐fluorenylene)‐vinylene‐co‐(carboxy‐2,5‐phenylene)‐vinylene] ( P1 ), poly[(9,9‐didodecyl‐2,7‐fluorenylene)‐vinylene‐co‐(carboxy‐2,5‐phenylene)‐vinylene‐co‐(4,7‐benzothiadiazolylene)‐vinylene] ( P2 ), and poly[(9,9‐didodecyl‐2,7‐fluorenylene)‐vinylene‐co‐(carboxy‐2,5‐phenylene)‐vinylene‐co‐2,5‐thienylene‐vinylene] ( P3 ) were used in DSSC devices, obtaining conversion efficiencies up to 0.88% ( P3 ). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterization of thiazolothiazole‐based polymers and their applications in polymer solar cells

A novel series of thiazolothiazole (Tz)‐based copolymers, poly[9,9‐didecylfluorene‐2,7‐diyl‐alt‐2,5‐bis‐(3‐hexylthiophene‐2‐yl)thiazolo[5,4‐d]thiazole] (P1), poly[9,9‐dioctyldibenzosilole‐2,7‐diyl‐alt‐2,5‐bis‐(3‐hexylthiophene‐2‐yl)thiazolo[5,4‐d]thiazole] (P2), and poly[4,4′‐bis(2‐ethylhexyl)‐dithieno[3,2‐b:2′,3′‐d]silole‐alt‐2,5‐bis‐(3‐hexylthiophene‐2‐yl)thiazolo[5,4‐d]thiazole] (P3), were synthesized for the use as donor materials in polymer solar cells (PSCs). The field‐effect carrier mobilities and the optical, electrochemical, and photovoltaic properties of the copolymers were investigated. The results suggest that the donor units in the copolymers significantly influenced the band gap, electronic energy levels, carrier mobilities, and photovoltaic properties of the copolymers. The band gaps of the copolymers were in the range of 1.80–2.14 eV. Under optimized conditions, the Tz‐based polymers showed power conversion efficiencies (PCEs) for the PSCs in the range of 2.23–2.75% under AM 1.5 illumination (100 mW/cm²). Among the three copolymers, P1, which contained a fluorene donor unit, showed a PCE of 2.75% with a short‐circuit current of 8.12 mA/cm², open circuit voltage of 0.86 V, and a fill factor (FF) of 0.39, under AM 1.5 illumination (100 mW/cm²). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterization of isoindigo‐based polymers using CH‐arylation polycondensation reactions for organic photovoltaics

A series of three new low bandgap donor–acceptor–donor–acceptor^/ (D–A–D–A^/) polymers have been successfully synthesized based on the combination of isoindigo as the electron‐deficient acceptor and 3,4‐ethylenedioxythiophene as the electron‐rich donor, followed by CH‐arylation with different acceptors (4,7‐dibromo[c][1,2,5]‐(oxa, thia, and/or selena)diazole ( 4a‐c )). These polymers were used as donor materials for photovoltaic applications. All of the polymers are highly stable and show good solubility in chlorinated solvents. The highest power conversion efficiency of 1.6% was achieved in the bulk heterojunction photovoltaic device that consisted of poly ((E)?6‐(7‐(benzo‐[c][1,2,5]‐thiadiazol‐4‐yl)?2,3‐dihydrothieno‐[3,4‐b][1,4]dioxin‐5‐yl)?6′‐(2,3‐dihydrothieno‐[3,4‐b][1,4]‐dioxin‐5‐yl)?1,1′‐bis‐(2‐octyldodecyl)‐[3,3′‐biindolinylidene]‐2,2′‐dione) as the donor and PC₆₁BM as the acceptor, with a short‐circuit current density (J_sc) of 8.10 mA/cm², an open circuit voltage (V_oc) of 0.56 V and a fill factor of 35%, which indicates that these polymers are promising donors for polymer solar cell applications. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2926–2933     

Synthesis and applications of cyano‐vinylene‐based polymers containing cyclopentadithiophene and dithienosilole units for photovoltaic cells

Two β‐cyano‐thiophenevinylene‐based polymers containing cyclopentadithiophene ( CPDT‐CN ) and dithienosilole ( DTS‐CN ) units were synthesized via Stille coupling reaction with Pd(PPh₃)₄ as a catalyst. The effects of the bridged atoms (C and Si) and cyano‐vinylene groups on their thermal, optical, electrochemical, charge transporting, and photovoltaic properties were investigated. Both polymers possessed the highest occupied molecular orbital (HOMO) levels of about ?5.30 eV and the lowest unoccupied molecular orbital (LUMO) levels of about ?3.60 eV, and covered broad absorption ranges with narrow optical band gaps (ca. 1.6 eV). The bulk heterojunction polymer solar cell (PSC) devices containing an active layer of electron‐donor polymers ( CPDT‐CN and DTS‐CN ) blended with an electron‐acceptor, that is, [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) or [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM), in different weight ratios were explored under 100 mW/cm² of AM 1.5 white‐light illumination. The PSC device based on DTS‐CN: PC₇₁BM (1:2 w/w) exhibited a best power conversion efficiency (PCE) value of 2.25% with V_oc = 0.74 V, J_sc = 8.39 mA/cm², and FF = 0.36. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Synthesis and characterization of naphtho[2,1‐b:3,4‐b′]dithiophene‐based polymers with extended π‐conjugation systems for use in bulk heterojunction polymer solar cells

Two novel polymeric semiconductor materials based on naphtho[2,1‐b:3,4‐b']dithiophene (NDT), PNDT‐TTT and PNDT‐TET , were designed and synthesized. These synthesized polymers were tested in bulk heterojunction solar cells as blends with the acceptor [6,6]‐phenyl‐C71‐butyric acid methyl ester (PC₇₁BM). PNDT‐TTT contained tri‐thiophene units, and PNDT‐TET contained bi‐thiophene units coupled by ethylenic linkages. Comparison to the properties of PNDT‐T , which contained single thiophene units, these polymers exhibit red‐shifted absorption spectra as a result of the enhanced conjugation lengths. These effects resulted in high short circuit currents (J_SC) in the organic solar cells. The PNDT‐TET ‐ and PNDT‐TTT ‐based devices exhibited considerably better photovoltaic performances, with power conversion efficiencies of 3.5 and 3.3%, respectively, compared to the PNDT‐T ‐based device (1.3%). © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4742–4751