Some N-alkyl-naphthylazo pyridinium salts as new reagents for the spectrophotometric determination of anionic surfactants

Summary Eleven pyridinium azo dyes with straight-chain alkyl groups C_nH_2n+1–(n=6–18) and bromoalkyl groups BrC_mH_2m–(m=6–12) were synthesized with the intention of developing reagents for the determination of low levels of anionic surfactants in an aqueous medium. The effect of the alkyl chain length of these reagents on the reactivity with anionic surfactants such as sodium dodecylsulphate (SDS), sodium linear-dodecylbenzenesulphonate (DBS), sodium dodecylsulphonate (DS) and sodium laurate (SL) was studied. It was found that the alkyl chain length played an important role in the formation of ion associates and the composition of the ion associates formed. These reagents were classified into four groups with respect to the reactivity with anionic surfactants. The first group (n,m=6) reacts only with DBS. The second group (n,m=8) reacts with SDS, DBS and DS. The third group (n,m=10, 12) reacts with SDS, DBS and DS; however, the colour intensity of the DBS-ion associate was unstable. The fourth group (n=14, 16, 18) reacts with all anionic surfactants examined, and the composition of the ion associates with SDS and DS was 2:1 ([reagent]/[surfactant]) though that of the ion associates of the three reagent groups mentioned above was 1:1. The optimal conditions for the determination of anionic surfactants in river water with 1-octyl-4-(4-aminonaphthylazo)-pyridinium bromide was examined. The calibration graph was linear up to 3×10^–6 mol/l, and the apparent molar absorptivity of the ion associate was 3.8×10⁴ l mol^–1 cm^–1 (at 427 nm). The relative standard deviation for 2.4×10^–6 mol/l SDS was 4.9%. Recoveries of 88–107% were found for 8.0×10^–7 mol/l SDS in river water samples.     

Determination of thallium in the presence of large excess of lead by anodic stripping voltammetry

The paper is concerned with the determination of traces of thallium, as T1(I), in the presence of very large amounts of lead, by d.c. anodic stripping voltammetry, by adding both a complexing agent and anionic surfactant. The supporting complexing agent was 0.1M solution of EDTA (pH 4.4). The influence of the several surfactants on the signals of lead and thallium was investigated.In 0.1M EDTA at pH 4.4 at the absence of a surfactant, lead does not interfere at concentrations below 10^–4 M. When the electrolyte contains also an anionic surfactant, lead can be tolerated at concentrations up to 2 × 10^–3–6 × 10^–3 M (depending on the type of the surfactant), and the height of the thallium peak remains unaffected. This makes the determination of 10^–8 M T1(I) possible when the molar excess of lead is 2–6 × 10⁵ fold. The method has been tested by determining the thallium content of soil extracts.     

Voltammetric study of glibenclamide at carbon paste and Sephadex-modified carbon paste electrodes

The oxidative behaviour of the antidiabetic agent glibenclamide on a bare carbon paste electrode (CPE) and a Sephadex-modified carbon paste electrode (SMCPE) was explored by cyclic and differential pulse voltammetry (DPV). The analysis procedure consisted of an open circuit accumulation step in stirred sample solution of Britton-Robinson buffer (0.04 mol L^–1, pH 2.0). This was followed by medium exchange to a clean solution of Britton-Robinson buffer (0.04 mol L^–1, pH 5.0), and subsequently an anodic potential scan was effected to obtain the voltammetric peak. The glibenclamide oxidation peak current obtained by DPV was proportional to the concentration of the glibenclamide in the range of 1.0×10^–9 mol L^–1 to 5.0×10^–8 mol L^–1 for 180 s accumulation time, with a detection limit of 4.0×10^–10 mol L^–1. A method was developed for the determination of glibenclamide in formulation and spiked human serum. Moreover, the proposed procedure was used to estimate the serum concentrations after oral administration of a 5 mg tablet of glibenclamide to three diabetic subjects.     

Spectrophotometric determination of anionic surfactants in tap and river waters with 1-(10-bromodecyl)-4-(4-aminonaphthylazo)-pyrimidinium bromide

Summary A new cationic dye, 1-(10-bromodecyl)-4-(4-aminonaphthylazo)-pyridinium bromide, was synthesized and evaluated as a new reagent for the determination of anionic surfactants. The reagent reacts with anionic surfactants, such as sodium dodecylsulphate and sodium dodecylbenzenesulphonate, to produce an ion associate in an aqueous medium. The colour change occurs simultaneously, and the colour development is very stable. This makes it possible to determine anionic surfactants directly by spectrophotometry without solvent extraction. The stoichiometric ratio of the ion associate was found to be 1:1 by the mole ratio method. The calibration graph was linear up to 2.5×10^–6 mol/l. The apparent molar absorptivity of the ion associate was 5.3×10⁴ l mol^–1 cm^–1 (at 595 nm). The relative standard deviation (n=10) for 1.2×10^–6 mol/l sodium dodecylsulphate was 4.9%. The proposed method was applied to the determination of anionic surfactants in tap and river waters.     

Spectrophotometric determination of cationic and anionic surfactants with anionic dyes in the presence of nonionic surfactants,part II: Development of batch and flow injection methods

On the basis of the changes in absorption spectra of azo dyes on the addition of an organic onium ion, spectrophotometric methods for the determination of organic onium salts and anionic surfactants were developed, and applied to flow injection method. Propyl orange (PO^–) was used for the determination of organic onium ions. Pairs of PO^– and Zeph⁺ (tetradecyldimethyl-benzylammonium ion) or PO^– and nC₁₈TMA⁺ (n-octadecyltrimethylammonium ion) were used for the determination of anionic surfactants. The determination range of organic onium ions were (0–3) × 10^–5 M by a batch method and were (0–2) × 10^–5 M by a flow injection method. The determination ranges of anionic surfactants were (0–2) × 10^–5 M by the batch method, and were (0–5) × 10^–5 M by the flow injection method, and the detection limit corresponding toS/N = 3 was 3 × 10^–7 M by the flow injection method. By the proposed flow injection method, anionic surfactants in water samples were determined.     

Determination of dopamine in synthetic cerebrospinal fluid by SWV with a graphite–polyurethane composite electrode

This work describes an electroanalytical investigation of dopamine using cyclic voltammetry (CV) and the graphite–polyurethane composite electrode (GPU). In CV studies, well-defined redox peaks characterize the oxidation process at the GPU electrode, which is indicative of electrocatalytic effects associated with active sites on the GPU electrode surface. A new analytical methodology was developed using the GPU electrode and square wave voltammetry (SWV) in BR buffer solution (0.1 mol L^–1; pH 7.4). Analytical curves were constructed under optimized conditions (f=60s^–1, E_a=50 mV, E_I=2 mV) and detection and quantification limits of 6.4×10^–8 mol L^–1 (12.1 g L^–1) and 5.2×10^–6 mol L^–1 (0.9 mg L^–1), respectively, were achieved. The precision of the method was checked by performing ten successive measurements for a 9.9×10^–6 mol L^–1 dopamine solution. For intra-assay and inter-assay precisions, the relative standard deviations were 1.9 and 2.3%, respectively. In order to evaluate the developed methodology, the determination of dopamine was performed with good sensitivity and selectivity, without the interference of ascorbic acid in synthetic cerebrospinal fluid, which indicates that the new methodology enables reliable analysis of dopamine.     

Use of ICP and XAS to determine the enhancement of gold phytoextraction by <Emphasis Type="Italic">Chilopsis linearis</Emphasis> using thiocyanate as a complexing agent

Under natural conditions gold has low solubility that reduces its bioavailability, a critical factor for phytoextraction. Researchers have found that phytoextraction can be improved by using synthetic chelating agents. Preliminary studies have shown that desert willow (Chilopsis linearis), a common inhabitant of the Chihuahuan Desert, is able to extract gold from a gold-enriched medium. The objective of the present study was to determine the ability of thiocyanate to enhance the gold-uptake capacity of C. linearis. Seedlings of this plant were exposed to the following hydroponics treatment: (1) 5 mg Au L^–1 (2.5×10^–5 mol L^–1), (2) 5 mg Au L^–1+10^–5 mol L^–1 NH₄SCN, (3) 5 mg Au L^–1+5×10^–5 mol L^–1 NH₄SCN, and (4) 5 mg Au L^–1+10^–4 mol L^–1 NH₄SCN. Each treatment had its respective control. After 2 weeks we determined the effect of the treatment on plant growth and gold content by inductively coupled plasma–optical emission spectroscopy (ICP–OES). No signs of shoot-growth inhibition were observed at any NH₄SCN treatment level. The ICP–OES analysis showed that addition of 10^–4 mol L^–1 NH₄SCN increased the concentration of gold by about 595, 396, and 467% in roots, stems, and leaves, respectively. X-ray absorption spectroscopy (XAS) studies showed that the oxidation state of gold was Au(0) and that gold nanoparticles were formed inside the plants.     

Spectrophotometric determination of manganese with derivatives of 1,3,3-trimethyl-2-[3-(1,3,3-trimethyl-1,3- H-indol-2-ylidene)propenyl]-3 H-indolium

A new, simple, rapid, and sensitive spectrophotometric method has been developed for the determination of manganese in sewage. The method is based on the reaction of manganese with derivatives of 1,3,3-trimethyl-2-[3-(1,3,3-trimethyl-1,3-H-indol-2-ylidene)propenyl]-3H-indolium to form a colored ion associate with a sensitive absorption maximum at 560 nm. The appropriate reaction conditions have been established: pH 8.5–10.0, 1.25–2.3×10^–3 mol L^–1 1-nitroso-2-naphthol, and 1.6–2.4×10^–4 mol L^–1 dye reagent. Beer's law is obeyed for manganese concentrations up to 4.2 mg L^–1. The limit of detection is 0.01 mg L^–1 Mn²⁺; the molar absorptivity of the ion associate was 7.5×10⁴ L mol^–1 cm^–1. The effect of various foreign ions was examined. A reaction mechanism is suggested. The developed procedure was tested for determination of manganese in sewage with satisfactory precision and accuracy.     

Investigation of 2-[(<Emphasis Type="Italic">E</Emphasis>)-2-(4-diethylaminophenyl)-1-ethenyl]-1,3,3-trimethyl-3H-indolium as a new highly sensitive reagent for the spectrophotometric determination of nitrophenols

A new, simple, rapid, and sensitive spectrophotometric method has been developed for the determination of nitrophenols [picric acid (PA); dinitrophenols (DNP)] in wastewater samples. The method is based on the reaction of nitrophenols with 2-[(E)-2-(4-diethylaminophenyl)-1-ethenyl]-1,3,3-trimethyl-3 H-indolium chloride reagent to form the colored ion associates, which are extracted by organic solvents. The molar absorptivity of the ion associates of PA with the investigated reagent ranges from 8.3×10⁴ to 11.3×10⁴ L mol^–1 cm^–1, depending on the extractant. Because only PA is extracted in an acidic medium with the investigated reagent, but both PA and DNP are extracted in an alkaline medium, it is possible to determine both substances in a mixture. Appropriate reaction conditions have been established. The absorbance of the colored extracts obeys Beers law in the range of 0.04–4.58 mg L^–1 PA, 1.0–18.4 mg L^–1 2,4-DNP and 1.2–14.7 mg L^–1 2,6-DNP, respectively. The limit of detections, calculated from a blank test (n=10; P=0.95), are 0.05 mg L^–1 PA, 0.9 mg L^–1 (2,4-DNP), and 1.1 mg L^–1 (2,6-DNP), respectively.     

Anodic stripping voltammetric determination of mercury using multi-walled carbon nanotubes film coated glassy carbon electrode

An electrochemical method for the determination of trace levels of mercury based on a multi-walled carbon nanotubes (MWNT) film coated glassy carbon electrode (GCE) is described. In 0.1 mol L^–1 HCl solution containing 0.02 mol L^–1 KI, Hg²⁺ was firstly preconcentrated at the MWNT film and then reduced at –0.60 V. During the anodic potential sweep, reduced mercury was oxidized, and then a sensitive and well-defined stripping peak at about –0.20 V appeared. Under identical conditions, a MWNT film coated GCE greatly enhances the stripping peak current of mercury in contrast to a bare GCE. Low concentrations of I^– remarkably improve the determining sensitivity, since this increases the accumulation efficiency of Hg²⁺ at the MWNT film coated GCE. The stripping peak current is proportional to the concentration of Hg²⁺ over the range 8×10^–10–5×10^–7 mol L^–1. The lowest detectable concentration of Hg²⁺ is 2×10^–10 mol L^–1 at 5 min accumulation. The relative standard deviation (RSD) at 1×10^–8 mol L^–1 Hg²⁺ was about 6% (n=10). By using this proposed method, Hg²⁺ in some water samples was determined, and the results were compared with those obtained by atomic absorption spectrometry (AAS). The two results are similar, suggesting that the MWNT-film coated GCE has great potential in practical analysis.     

Determination of trace europium by use of the new fluorescence system europium–sparfloxacin–1,10-phenanthroline–sodium dodecyl sulfate

A new lanthanide-sensitized luminescence system: europium–sparfloxacin–1,10-phenanthroline–sodium dodecyl sulfate has been discovered. The spectrofluorimetric properties of the system were studied. The effect of experimental conditions on the fluorescence intensity was defined. Under the optimum conditions, the fluorescence intensity of the system is a linear function of the concentration of europium in the range 5.0×10^–9–1.0×10^–6 mol L^–1 and the detection limit is 1.0×10^–10 mol L^–1. The system was used for the determination of trace amounts of europium in rare earth samples with satisfactory results.     

Determination of subnanomolar concentrations of cobalt by adsorptive stripping voltammetry at a bismuth film electrode

Procedures for trace cobalt determinations by adsorptive stripping voltammetry at in situ and ex situ plated bismuth film electrodes are presented. These exploit the enhancement of the cobalt peak obtained by using the Co(II)–dimethylglyoxime–cetyltrimethylammonium bromide–piperazine-N,N-bis(2-ethanesulfonic acid) system. The calibration graph for an accumulation time of 120 s was linear from 2 × 10^–10 to 2 × 10^–8 mol L^–1. The relative standard deviation from five determinations of cobalt at a concentration of 5 × 10^–9 mol L^–1 was 5.2%. The detection limit for an accumulation time of 300 s was 1.8 × 10^–11 mol L^–1. The proposed procedure was applied to cobalt determination in certified reference materials and in tap and river water samples.     

A spectrophotometric flow procedure for the determination of cationic surfactants in natural waters using a solenoid micro-pump for fluid propulsion

An automatic flow-analysis procedure for spectrophotometric determination of cationic surfactants in surface water using a solenoid micro-pump for propelling solutions of reagents and sample is described. The proposed method is based on a ternary formation complex between chromazurol S, the Fe(III) ion, and the cationic surfactant. The flow network comprised four solenoid micro-pumps controlled by a microcomputer, which performed the sampling step by loading a reaction coil with sample and reagent solutions and displacing the sample zone through the analytical path. The system is simple, easy to operate, and very flexible, with sufficient sensitivity to determine cationic surfactants in water without any pre-concentration or separation step. After determining the best operational conditions, favourable features such as a linear response between 0.34 and 10.2?mg?L^?1 of surfactant (R?=?0.999), a relative standard deviation of 0.6% (n?=?11) for a sample containing 3.4?mg?L^?1 of surfactant, a detection limit of 0.035?mg?L^?1 of surfactant, and a sampling throughput of 72 determinations per hour were achieved. The system was used to determine cationic surfactant in river-water samples, and recovery values between 91 and 106% were achieved.     

Development and Validation of a Capillary Electrophoresis Method for the Determination of Denatonium Benzoate in Denaturated Alcohol Formulations

Capillary electrophoretic (CE) technique was investigated for the rapid analysis of denatonium benzoate (Bitrex), a quaternary ammonium salt, in several denaturated alcohol formulations. The optimized separations were carried out in 0.025 mol L^–1 Tris-phosphate electrolyte (pH 7.0) using direct UV detection at 214 nm. In order to prevent precipitation of hydrophobic matrix components in aqueous electrolyte, an electrokinetic sample introduction mode with internal standard (triethylbenzylammonium chloride) was used. Valid calibration (r²=0.998) was demonstrated in the range 2-50 mg L^–1 of Bitrex. The detection limit determined for 10 s electrokinetic (5 kV) injection was 0.45 mg L^–1 (three times the baseline noise). The proposed method was applied to the determination of Bitrex in various Lithuanian denaturated alcohol formulations and the results were statistically comparable with those obtained by HPLC technique.     

Simultaneous Determination of Aromatic Amines by Liquid Chromatography Coupled with Carbon Nanotubes/Poly (3-methylthiophene) Modified Dual-Electrode

Liquid chromatography with amperometric detection (LC-AD) is developed and applied to simultaneously determine five aromatic amines. In the LC-AD, a new carbon nanotubes/poly(3-methylthiophene) modified dual-electrode is fabricated and then used as the working electrode. It is found that this chemically modified electrode (CME) exhibits efficiently electrocatalytic oxidation for aromatic amines with relatively high sensitivity, stability and long-life. Thus, lower detection in LC-AD can be achieved, which are 4.0 × 10^–8 mol L^–1 for aniline, 1.6 ×10^–7 mol L^–1 for 4-nitroaniline, 1.0 × 10^–7 mol L^–1 for 4-chloroaniline, 1.5 × 10^–7 mol L^–1 for 1-naphthylamine, 1.7 × 10^–7 mol L^–1 for 2-bromoaniline. The recoveries of the five analytes are also determined, which range between 0.95 and 1.05 for drinking water, 0.86 and 1.10 for the LiWa River water.     

A novel amperometric sensor and chromatographic detector for determination of parathion

A novel amperometric sensor and chromatographic detector for determination of parathion has been fabricated from a multi-wall carbon nano-tube (MWCNT)/Nafion film-modified glassy-carbon electrode (GCE). The electrochemical response to parathion at the MWCNT/Nafion film electrode was investigated by cyclic voltammetry and linear sweep voltammetry. The redox current of parathion at the MWCNT/Nafion film electrode was significantly higher than that at the bare GCE, the MWCNT-modified GCE, and the Nafion-modified GCE. The results indicated that the MWCNT/Nafion film had an efficient electrocatalytic effect on the electrochemical response to parathion. The peak current was proportional to the concentration of parathion in the range 5.0×10^–9–2.0×10^–5 mol L^–1. The detection limit was 1.0×10^–9 mol L^–1 (after 120 s accumulation). In high-performance liquid chromatography with electrochemical detection (HPLC–ED) a stable and sensitive current response was obtained for parathion at the MWCNT/Nafion film electrode. The linear range for parathion was over four orders of magnitude and the detection limit was 6.0×10^–9 mol L^–1. Application of the method for determination of parathion in rice was satisfactory.     

Spectrofluorimetric Assay of Cationic Surfactants by Fluorescence Quenching of 9-Anthracenecarboxylic Acid

A new simple, selective and sensitive fluorescence quenching method was developed to determine cationic surfactants with the 9-anthracenecarboxylic acid (ACA). The fluorescence intensity of ACA was decreased by addition of trace amounts of cationic surfactants. Under optimum conditions, the ratio of fluorescence intensity in the absence and presence of cationic surfactants was proportional to the concentration of cationic surfactants over the range of 0.3–4.5 × 10⁻⁵ mol L⁻¹ for cetylpyridinium chloride (CPC) and 0.4–6.0 × 10⁻⁵ mol L⁻¹ for cetyl trimethyl-ammonium bromide (CTAB). The detection limits are 1.0 × 10⁻⁶ mol L⁻¹ for CPC and 1.2 × 10⁻⁶ mol L⁻¹ for CTAB, respectively. Based on this approach, this paper presents a new quantitative method for cationic surfactants assay.     

A flow-injection ultrafiltration sampling chemiluminescence system for on-line determination of drug–protein interaction

A flow-injection ultrafiltration sampling chemiluminescence system for on-line determination of cimetidine–bovine serum albumin (BSA) interaction is proposed in this paper. Cimetidine can be oxidized by N-bromosuccinimide (NBS) and sensitized by fluorescein to produce high chemiluminescence emission in basic media. The concentration of cimetidine is linear with the CL intensity in the range 3×10^–7–1×10^–4 mol L^–1 with a detection limit of 1×10^–7 mol L^–1 (3). The drug and protein were mixed in different molar ratios in 0.067 mol L^–1 phosphate buffer, pH 7.4, and incubated at 37 °C in a water bath. The ultrafiltration probe was utilized to sample the mixed solution at a flow rate of 5 µL min^–1. The data obtained by the proposed ultrafiltration flow-injection chemiluminescence method was analyzed with Scrathard analysis and a Klotz plot. The estimated association constant (K) and the number of the binding site (n) on one molecule of BSA by Scrathard analysis and Klotz plot were 3.15×10⁴ L mol^–1 and 0.95, 3.25×10⁴ L mol^–1 and 0.92, respectively. The proposed system proved that flow-injection chemiluminescence analysis coupled with on-line ultrafiltration sampling is a simple and reliable technique for the study of drug–protein interaction.     

Voltammetric behaviour of the zirconium-phenylfluorone-hexadecyl pyridinium chloride system and the sensitizing effect of surfactants

The adsorptive voltammetric features of the zirconium-phenylfluorone (PF)-hexadecyl pyridinium chloride (CPC) system has been investigated. A sensitizing effect of the surfactant CPC on the adsorption current of the Zr-PF-CPC system were observed by linear potential sweep voltammetry. A new sensitive method determining Zr traces was established, the detection limit and linear relationship is 5.0×10^–9 mol/l and 7.7×10^–9–1.1×10^–7 mol/l, respectively. This method has been applied to mineral samples.     

Fabrication of a novel Li<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>MoO<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript> film modified electrode and its application as an electrochemical sensor of iodate

A novel organic gel film modified electrode was simply and conveniently fabricated by casting Li_xMoO_y and polypropylene carbonate (PPC) onto the surface of a gold electrode. The cyclic voltammetry and amperometry studies demonstrated that the Li_xMoO_y film modified electrode has a high stability and a good electrocatalytic activity for the reduction of iodate. In amperometry, a good linear relationship between the steady current and the concentration of iodate was obtained in the range from 3×10^–7 to 1×10^–4 mol L^–1 with a correlation coefficient of 0.9997 and a detection limit of 1×10^–7 mol L^–1.