Influence of the precursor salts in the synthesis of CaSnO<Subscript>3</Subscript> by the polymeric precursor method

CaSnO₃ was synthesized by the polymeric precursor method, using different precursor salts as (CH₃COO)₂Ca·H₂O, Ca(NO₃)₂·4H₂O, CaCl₂·2H₂O and CaCO₃, leading to different results. Powder precursor was characterized using thermal analysis. Depending on the precursor different thermal behaviors were obtained. Results also indicate the formation of carbonates, confirmed by IR spectra. After calcination and characterization by XRD, the formation of perovskite as single phase was only identified when calcium acetate was used as precursor. For other precursors, tin oxide was observed as secondary phase.     

SrSnO<Subscript>3</Subscript>:Nd obtained by the polymeric precursor method

In this work, the synthesis of Nd-doped SrSnO₃ by the polymeric precursor method, with calcination between 250 and 700 °C is reported. The powder precursors were characterized by TG/DTA and high temperature X-ray diffraction (HTXRD). After heat treatment, the material was characterized by XRD and infrared spectroscopy. Ester and carbonate amounts were strictly related to Nd-doping. According to XRD patterns, the orthorhombic perovskite was obtained at 700 °C for SrSnO₃ and SrSn_0.99Nd_0.01O₃. For Sr_0.99Nd_0.01SnO₃, the kinetics displayed an important hole in the crystallization process, as no peak was observed in HTXRD up to 700 °C, while a XRD patterns showed a crystalline material after calcination at 250 °C.     

Thermal synthesis of the CeO<Subscript>2</Subscript>-PrO<Subscript>2</Subscript>-Nd<Subscript>2</Subscript>O<Subscript>3</Subscript>pigments

Summary The synthesis of new compounds based on the CeO₂-PrO₂-Nd₂O₃system, which can be used as pigments for colouring of ceramic glazes, is investigated in our laboratory. The optimum conditions for the syntheses of these compounds have been estimated. The methods of thermal analysis provided first information about the temperature region of the formation of the pigments investigated. The synthesis of these compounds was followed by thermal analysis using STA 449/C Jupiter (Netzsch, Germany).     

Thermal synthesis of the (Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>)<Subscript>1–x</Subscript>(Er<Subscript>2</Subscript>O<Subscript>3</Subscript>)<Subscript>x</Subscript> pigments

The synthesis of new compounds based on Bi₂O₃ is investigated because they can be used as new environmentally friendly inorganic pigments. Chemical compounds of the (Bi₂O₃)_1–x(Er₂O₃)_x type were synthetized. The host lattice of these pigments is Bi2O3 that is doped by Er³⁺ ions. The incorporation of doped ions provides interesting colours and contributes to an increase in the thermal stability of these compounds. The simultaneous TG-DTA measurements were used for determination of the temperature region of the pigment formation and thermal stability of pigments.     

Thermal behavior of Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> mesoporous gels

Summary Titania-based photocatalytic materials were prepared by sol-gel method using Fe³⁺ and polyethyleneglycol (PEG₆₀₀) as additives. Thermogravimetry (TG), differential thermal analysis (DTA) and evolved gas analysis (EGA) with MS detection were used to elucidate processes that take place during heating of Fe³⁺ containing titania gels. The microstructure development of the Fe₂O₃/TiO₂ gel samples with and without PEG₆₀₀ admixtures was characterized by emanation thermal analysis (ETA) under in situ heating in air. A mathematical model was used for the evaluation of ETA results. Surface area and porosity measurements of the samples dried at 120&deg;C and the samples preheated for 1 h to 300 and 500&deg;C were compared. From the XRD measurements it was confirmed that the crystallization of anatase took place after thermal heating up to 600&deg;C.     

Thermal behaviour and fragility of Sb<Subscript>2</Subscript>O<Subscript>3</Subscript>-containing zinc borophosphate glasses

Thermal behaviour of the glass series (100-x)[50ZnO-10B₂O₃-40P₂O₅]·xSb₂O₃ (x=0-42 mol%) and (100-y)[60ZnO-10B₂O₃-30P₂O₅]·ySb₂O₃ (y=0-28 mol%) was investigated by DSC and TMA. The addition of Sb₂O₃ results in a decrease of the glass transition temperature and crystallization temperature in both compositional series. All glasses crystallize on heating in the temperature range of 522–632°C. Thermal expansion coefficient of the glasses monotonously increases with increasing Sb₂O₃ content in both series and varies within the range of 6.6–11.7 ppm °C⁻¹. From changes of thermal capacity within the glass transition region it was concluded that with increasing Sb₂O₃ content the ‘fragility’ of the studied glasses increases.     

Effect of the modifier ion on the properties of MgFe<Subscript>2</Subscript>O<Subscript>4</Subscript> and ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> pigments

Magnesium and zinc ferrites have been prepared by the polymeric precursor method. The organic material decomposition was studied by thermogravimetry (TG) and differential thermal analysis (DTA). The variation of crystalline phases and particle morphology with calcination temperature were investigated using X-ray diffraction (XRD) and scanning electronic microscopy (SEM), respectively. The colors of the ferrites were evaluated using colorimetry. Magnesium ferrite crystallizes above 800°C, presenting a yellow- orange color with a reflectance peak at the 600–650 nm range, while zinc ferrite crystallizes at 600°C, with a reflectance peak between 650–700 nm, corresponding to the red-brick color.     

Synthesis of Bi<Subscript>4</Subscript>Ge<Subscript>3</Subscript>O<Subscript>12</Subscript> ceramic scintillators by the polymeric precursor method

Bismuth germanate ceramic powders were synthesized for the first time by the polymeric precursor method (Pechini’s method). Differential thermal analysis and thermogravimetric techniques were used to study the decomposition of the resin precursor, which indicated a suitable calcination temperature at 600 °C. It was observed that the mass loss occurs in two main stages that are associated with two exothermic reactions. The crystalline phases of the powders were inspected by the X-ray diffraction technique after thermal treatment between 300 and 600 °C. Single phase Bi₄Ge₃O₁₂ ceramic bodies were obtained after sintering at 840 °C for 10 h. The sintered ceramics presented a luminescence band emission centred at around 530 nm when excited with X-rays and UV radiation.     

Effect of nucleating agents on the crystallization of Li<Subscript>2</Subscript>O-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript> system glass

The processes of nucleation of Li₂O-Al₂O₃-SiO₂ glasses with TiO₂ and TiO₂+ZrO₂ as nucleating agents were discussed. The DTA peak temperature and DTA peak height shown a strong dependence on the nucleation temperature in the glass with TiO₂, while in the glass with TiO₂+ZrO₂ this tendency was small. The optimum nucleation temperatures were 745 and 760°C for two glasses. It suggested that with TiO₂+ZrO₂ as nucleating agents, the crystallization had lower sensitivity for nucleation temperature, and the glass had higher nucleation efficiency than with TiO₂.     

The effects of Co,Ni and Mn on the thermal processing of Zn<Subscript>2</Subscript>TiO<Subscript>4</Subscript> pigments

Summary  In this work, the thermodynamic activation and kinetic study of mineral lubricant oils was accomplished using isothermal and non-isothermal thermogravimetry based on mass loss as a function of time and temperature. The thermodynamic and kinetic behavior of the mineral lubricant oils depends on the atmosphere and heating rates used in TG analysis. The kinetic and thermodynamic results were satisfactory, presenting good correlation, with a linear correlation coefficient close to unit with a low standard deviation.     

Thermal decomposition of the carbon nanotube/SiO<Subscript>2</Subscript>precursor powders

Summary TG-DSC-MS (thermogravimetry-differential scanning calorimetry-mass spectrometry) coupling techniques were used to make a simultaneous characterizing study for the thermal decomposition process of the carbon nanotube (CNT)/SiO₂precursor powders prepared by rapid sol-gel method. The thermal stability of the CNT and the SiO₂pure gel were investigated by TG-DSC. The results showed that the oxidation of CNT began from 530 and combusted at about 678°C at the heating rate of 10°C min^-1in air. Moreover, the faster the heating rate, the higher the temperature of CNT combustion. The appropriate calcinations temperature of the CNT/SiO₂precursor powders should be held for 1 h at 500°C.     

Constant transformation rate thermal analysis of HGdP<Subscript>2</Subscript>O<Subscript>7</Subscript>·3H<Subscript>2</Subscript>O

Summary The aim of this work is the optimization of the preparation of anhydrous gadolinium hydrogen phosphate with good fluorescence properties. The products obtained by dehydration of gadolinium hydrogen phosphate trihydrate depend on the conditions chosen for the thermal treatment. For this reason, the dehydration was followed by Constant Rate Thermal Analysis whilst strictly controlling the water vapour pressure above the sample. Intermediate samples, obtained during dehydration were characterised by IR spectroscopy and X-ray diffraction. It has thus been shown that the thermal pathway taken for the dehydration depends on the water vapour pressure above the sample in the region from 10^-2to 5 mbar. Under the lowest water vapour pressure (5·10^-3mbar), the elimination of the crystallization water is carried out in a continuous way and produces a quasi-amorphous intermediate. Under higher water vapour pressure (5 mbar), well crystallized intermediate products are obtained. The results obtained suggest that the trihydrate contains zeolitic water which confirms a prior structural study.     

Thermal oxide synthesis and characterization of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanorods and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanowires

Fe₃O₄ nanorods and Fe₂O₃ nanowires have been synthesized through a simple thermal oxide reaction of Fe with C₂H₂O₄ solution at 200–600°C for 1 h in the air. The morphology and structure of Fe₃O₄ nanorods and Fe₂O₃ nanowires were detected with powder X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The influence of temperature on the morphology development was experimentally investigated. The results show that the polycrystals Fe₃O₄ nanorods with cubic structure and the average diameter of 0.5–0.8 μm grow after reaction at 200–500°C for 1 h in the air. When the temperature was 600°C, the samples completely became Fe₂O₃ nanowires with hexagonal structure. It was found that C₂H₂O₄ molecules had a significant effect on the formation of Fe₃O₄ nanorods. A possible mechanism was also proposed to account for the growth of these Fe₃O₄ nanorods. Supported by the Fund of Weinan Teacher’s University (Grant No. 08YKZ008), the National Natural Science Foundation of China (Grant No. 20573072) and the Doctoral Fund of Ministry of Education of China (Grant No. 20060718010)     

Effects of the Chemical Modifier on the Thermal Evolution of SrBi<Subscript>2</Subscript>Ta<Subscript>2</Subscript>O<Subscript>9</Subscript> Precursor Powders

The effects of the chelating agent on the thermal evolution of SrBi₂Ta₂O₉ precursor powders were investigated. The precursor solutions were prepared from non-hydrolyzing precursors of bismuth and strontium and a tantalum alkoxide. The utilization of diethanolamine or triethanolamine as chelating agent was found to produce the segregation of metallic bismuth in the as-prepared powders, which led to the formation of a multiphase system. On the other hand, acetoin, one of the α-hydroxyketones, showed outstanding characteristics for the low-temperature synthesis of SrBi₂Ta₂O₉: elimination of residual organics at low temperature, an earlier onset of crystallization, and no segregation of secondary phases during the whole crystallization process.