用于超级电容器的锰钴氧化物/碳纤维材料

The development of high-performance supercapacitor electrode materials is imperative to alleviate the ongoing energy crisis. Numerous transition metals (oxides) have been studied as electrode materials for supercapacitors owing to their low cost, environmental-friendliness, and excellent electrochemical performance. Among the developed binary transition metal oxides, manganese cobalt oxides typically show high theoretical capacitance and stable electrochemical performance, and are widely used in the electrode materials of supercapacitors. However, the poor conductivity and active material utilization of manganese cobalt oxide-based electrode materials limit their potential capacitance application. Cotton is mainly composed of organic carbon-containing materials, which can be transformed to carbon fibers after calcination. The resultant carbonaceous material exhibits a large specific surface area and good conductivity. Such advantages could potentially suppress the negative effects caused by the poor conductivity and small specific surface area of manganese cobalt oxides, thereby improving the electrochemical performance. Herein, we firstly deposited manganese cobalt oxides on cotton by a simple hydrothermal method, yielding a composite of manganese cobalt oxides and carbon fibers via subsequent calcination, to improve the electrochemical performance of the electrode material. X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), X-ray photoelectron spectroscopy (XPS), Brunauer-Emmett-Teller (BET), thermogravimetric analysis (TGA), and electrochemical characterizations were used to investigate the physical, chemical, and electrochemical properties of the prepared samples. The fabricated manganese cobalt oxides in the composite were uniformly dispersed on the carbon fiber surface, which increased the contact between the interface of the electrode material and electrolyte, and enhanced electrode material utilization. The electrode material was confirmed to have well contacted with the electrolyte during a contact angle test. Hence, a pseudo-capacitance reaction completely occurred on the manganese cobalt oxide material. Moreover, the addition of carbon fibers reduced the resistance of the material, resulting in excellent capacitive performance. The capacitance of the prepared composite was 854 F∙g^-1 at a current density of 2 A∙g^-1. The capacitance was maintained at 72.3% after 2000 cycles at a current density of 2 A∙g^-1. These results indicate that the manganese cobalt oxide and carbon fiber composite is a promising electrode material for high-performance supercapacitors. The findings presented herein provide a strategy for coupling with carbon materials to enhance the performance of supercapacitor electrode materials based on manganese cobalt oxides. Thus, novel insights into the design of high-performance supercapacitors for energy management are provided.     

活性炭/钴氧化物干凝胶电化学电容器性能

以高性能活性炭作为负极材料, 将颗粒平均粒径为40~60 nm的纳米钴氧化物干凝胶作为正极材料组成电化学电容器, 研究了电容器在7 mol/L的KOH水溶液中的电化学性能, 其充放电电压可以达到1.4~1.6 V, 以材料本身重量计算的比能量和比功率分别达到15.4 W·h/kg和23.5 kW/kg.     

系列纳米结构锰氧化物的水热合成

以KMnO₄为锰源、抗坏血酸(AA)为还原剂,采用水热法制备系列纳米结构锰氧化物。通过调节反应物的物质的量的比、水溶液的pH值、反应温度和反应时间,制备出了不同纳米结构的锰氧化物,包括Mn₃O₄纳米粒子、MnOOH、α-MnO₂和β-MnO₂纳米棒。采用XRD和TEM测试技术对合成产物进行了表征,同时对其反应机理进行了探讨。     

锰氧化物聚苯胺复合电极材料的制备与性能

本文制备了二氧化锰和聚苯胺碳的复合电级材料(MnO₂-PAnC),测试结果表明MnO₂-PAnC材料为松散结构组成的纳米颗粒. MnO₂-PAnC 材料的比电容最大可达459 F•g^-1,MnO₂-PAnC电极在较高的扫速下循环伏安曲线变形较小,表现出良好的可逆性. 交流阻抗测试结果表明,MnO₂-PAnC 电极电荷传递电阻小,表面离子扩散速度快. 充放电500个循环后,MnO₂-PAnC 电容的保持率仍高于60%. 以上实验结果表明,MnO₂-PAnC 是很好的超级电容器的电极材料.     

自掺杂锰基氧化物La1-xMnO3+δ的电化学制备

利用阴极还原恒电位和恒电化学沉积法制备了自掺杂钙钛矿结构的锰基氧化物La1-xMnO3 δ,研究了电解质溶液中La^3 和Mn^2 的物质的量比、沉积电位以及电密度对产物组成的影响,并对电沉积机理和晶格缺陷进行了探讨,结果表明,晶格中的离子空位和Mn^4 的含量是影响体系输运性质的关键。     

水热合成部分还原氧化石墨烯-K2Mn4O8超级电容器纳米复合材料

通过控制水热反应温度以及氧化石墨烯(GO)与高锰酸钾的填料比, 合成了两组部分还原的GO-K₂Mn₄O₈纳米复合材料. X射线衍射(XRD)分析说明水热过程中合成了α-MnO₂和一种新的晶相K₂Mn₄O₈.通过X射线光电子能谱(XPS)分析了水热反应前后氧化石墨的含氧官能团的变化. 扫描电子显微镜(SEM)显示样品由片状还原的氧化石墨烯构成, 其表面附有许多小的纳米颗粒, 这种结构有利于储能时电子的传递. 通过这两组复合材料的结构分析, 更好地理解了材料的电化学性能的变化. 利用循环伏安法和恒流充放电测试比较了材料的电容性能. 用1 mol·L^-1的硫酸钠做电解液, 电位范围是0-1 V, 在1 A·g^-1的电流密度下, 测得的样品最佳比电容达到251 F·g^-1, 能量密度为32 Wh·kg^-1, 功率密度为18.2 kW·kg^-1. 并且在5 A·g^-1的电流密度下循环1000次后样品的比电容仍维持在初始比电容的88%.     

磁控溅射制备的铜钒氧化物薄膜及其电化学性能

采用射频磁控溅射技术在硅基底上分别制备了无掺杂和掺杂Cu的氧化钒薄膜. X射线衍射(XRD)分析和扫描电子显微镜(SEM)观察表明, 无掺杂的薄膜为多晶V2O5, 掺杂Cu的薄膜为非晶态. X射线光电子能谱(XPS)分析结果表明, 掺杂Cu的薄膜为铜钒氧化物膜, 其中Cu离子表现为+2价, V离子为+4与+5价的混合价态. 随着Cu掺杂量的增大, +4价V的含量增加. 电化学测试结果表明, V2O5薄膜在掺杂Cu以后其放电容量有显著的提高, 其中Cu2.1VO4.4薄膜在100次循环后容量还保持为83.4 μA·h·cm-2·μm-1, 表现出较高的放电容量和较好的循环性能.     

过渡元素及镧系元素11-钨锰杂多酸钾配合物的合成与性质

本文合成了以11-钨锰杂多阴离子为配体的4个配合物:K_6Z(H_2O)MnW_(11)O_(39)xH_2O(Z=ZD、Ni)和K_(13)Ln(MnW_(11)O_(39))_2·xH_2O(Ln=La、Nd)。用化学分析、离子交换、电导滴定、IR、UV、x-射线光电子能谱等进行了表征,还对其热性质等进行了研究。     

不同晶型和形貌MnO2纳米材料的可控制备

以KMnO4为锰源, 采用水热技术在180 ℃条件下于不同种类酸溶液中可控制备了α-, β-, δ-MnO2, 系统研究了 K＋, H＋及阴离子对制备产物MnO2晶型和形貌的影响. 研究结果表明, K＋与H＋在反应体系中对于制备产物晶相的生成形成竞争性影响, 其量的大小对制备产物晶型具有控制作用, 高浓度K＋离子有助于生成α-MnO2, 而高浓度的H＋有利于生成β-MnO2; 阴离子的种类和浓度对制备产物MnO2的晶型和形貌无显著影响. 在对制备产物进行XRD, SEM和元素分析的基础上, 提出了不同晶型和形貌MnO2的可能形成机理.     

Li1+xMn2O4的溶胶-凝胶法合成及其电化学性能

锂离子电池;锂锰氧化物;尖晶石结构;Li1+xMn2O4的溶胶-凝胶法合成及其电化学性能     

锰氧化物负载碳氮三维网络结构复合材料的制备及锂电性能

通过硝酸锰和乙醇的水热反应在三聚氰胺泡棉（MF）上生成三氧化二锰颗粒,氮气下高温处理后形成锰氧化物负载碳氮三维网络结构的复合物。碳氮网络结构提高了充放电过程中材料结构的稳定性及导电性,且烧结过程中产生的孔道结构有利于锂离子传输,使得该复合材料作为负极在锂离子电池中表现出优异的充放电性能和循环稳定性。材料的比容量和循环稳定性大大提高,经500℃处理后的MnO/CNnws-500材料在160次循环后仍然保留590 mAh·g^-1的比容量,达到氧化亚锰理论容量755 mAh·g^-1的78%。     

锰氧化物/碳氮三维网络结构复合材料的制备及锂电性能

通过硝酸锰和乙醇的水热反应在三聚氰胺泡棉(MF)上生成三氧化二锰颗粒,氮气下高温处理后形成锰氧化物负载碳氮三维网络结构的复合物。碳氮网络结构提高了充放电过程中材料结构的稳定性及导电性,且烧结过程中产生的孔道结构有利于锂离子传输,使得该复合材料作为负极在锂离子电池中表现出优异的充放电性能和循环稳定性。材料的比容量和循环稳定性大大提高,经500℃处理后的MnO/CNnws-500材料在160次循环后仍然保留590 m Ah·g~(-1)的比容量,达到氧化亚锰理论容量755 m Ah·g~(-1)的78%。     

Solution Layer Deposition: A Technique for the Growth of Ultra‐Pure Manganese Oxides on Silica at Room Temperature

With the ever increasing miniaturization in microelectronic devices, new deposition techniques are required to form high‐purity metal oxide layers. Herein, we report a liquid route to specifically produce thin and conformal amorphous manganese oxide layers on silicon substrate, which can be transformed into a manganese silicate layer. The undesired insertion of carbon into the functional layers is avoided through a solution metal–organic chemistry approach named Solution Layer Deposition (SLD). The growth of a pure manganese oxide film by SLD takes place through the decoordination of ligands from a metal–organic complex in mild conditions, and coordination of the resulting metal atoms on a silica surface. The mechanism of this chemical liquid route has been elucidated by solid‐state ²⁹Si MAS NMR, XPS, SIMS, and HRTEM.     

不同工作介质下二氧化锰/膨胀石墨复合材料的电化学电容器行为

研究了氧化还原法制备二氧化锰/膨胀石墨复合材料用作电化学电容器, 利用热重分析、比表面及X射线衍射方法对材料的组成及结构进行了表征, 利用三电极循环伏安及充放电循环法研究了材料在硫酸钠、氯化钠、氯化钾及硝酸钾不同电解质中的电化学行为. 研究结果表明, 二氧化锰以非晶态的形式在复合材料中存在, 膨胀石墨起良好电导作用, 随其用量的增加, 复合材料的比表面下降, 但二氧化锰的比电容增加. 不同工作介质中电化学行为显示, 复合材料电化学行为的不同主要跟阳离子的种类有关. 在钠离子电解质中, 复合材料电极体现较高的表观电容和真实电容, 在钾盐电解质体系中, 复合材料电极的电流响应速度比较快, 这是由于钠盐和钾盐溶液具有不同的水合数、水合半径和电导率. 当复合材料中膨胀石墨的用量为24%左右时, 复合材料在2 mV/s扫描速度下, 在1 mol/L Na₂SO₄溶液中体现的比电容为220 F/g, 复合材料显示优良的循环性能.     

Nanostructured Manganese Oxides within a Ring-Shaped Polyoxometalate Exhibiting Unusual Oxidation Catalysis

Nanosized manganese oxides have recently received considerable attention for their synthesis, structures, and potential applications. Although various synthetic methods have been developed, precise synthesis of novel nanostructured manganese oxides are still challenging. In this study, using a structurally defined nanosized cavity inside a ring-shaped polyoxometalate, we succeeded in synthesizing two types of discrete 18 and 20 nuclear nanostructured manganese oxides, Mn18 and Mn20 , respectively. In particular, Mn18 showed much higher catalytic activity than other manganese oxides for the oxygenation of alkylarenes including electron-deficient ones, and the reaction proceeded through a unique reaction mechanism due to its unusual manganese oxide structure.     

Lead and Cadmium Adsorption onto Iron Oxides and Manganese Oxides in the Natural Surface Coatings Collected on Natural Substances in the Songhua River of China

Natural surface coatings collected from natural substances(NSCsNS)were employed to study the roles of the main chemical components(iron oxides,manganese oxides,and other components)in controlling the adsorption of lead(Pb)and cadmium(Cd)in aquatic environments.The selective chemical extraction followed by the adsorption of Pb and Cd experiments and statistical analysis,were used to investigate the adsorption property of each component.Hydroxylamine hydrochloride was used to remove manganese oxides selectively,and sodium dithionite was used to extract iron oxides and manganese oxides.The result indicated that iron oxides and manganese oxides played an important role in the adsorption of Pb and Cd on NSCsNS,and the relative contribution was about two-thirds.The contribution of manganese oxides was the greatest,with a lesser role indicated for other components.The adsorption ability of manganese oxides for Pb and Cd was greater than that of iron oxides or other components for Pb and Cd.The Pb adsorption observed in each component was greater than Cd adsorption.     

Inherently Area-Selective Atomic Layer Deposition of Manganese Oxide through Electronegativity-Induced Adsorption

Manganese oxide (MnO_x) shows great potential in the areas of nano-electronics, magnetic devices and so on. Since the characteristics of precise thickness control at the atomic level and self-align lateral patterning, area-selective deposition (ASD) of the MnO_x films can be used in some key steps of nanomanufacturing. In this work, MnO_x films are deposited on Pt, Cu and SiO₂ substrates using Mn(EtCp)₂ and H₂O over a temperature range of 80–215 °C. Inherently area-selective atomic layer deposition (ALD) of MnO_x is successfully achieved on metal/SiO₂ patterns. The selectivity improves with increasing deposition temperature within the ALD window. Moreover, it is demonstrated that with the decrease of electronegativity differences between M (M = Si, Cu and Pt) and O, the chemisorption energy barrier decreases, which affects the initial nucleation rate. The inherent ASD aroused by the electronegativity differences shows a possible method for further development and prediction of ASD processes.