Ultrahigh‐density carbon nanoring arrays on a silicon wafer are achieved by a novel templated solution deposition method. Initially the silica nanodot arrays obtained from a nanoporous thin film are used as a template to direct the surface dewetting of a phenolic precursor, while further curing and calcination of the phenolic precursor, followed by etching of the silica arrays, results in large area carbon nanoring arrays with a diameter as small as 25 nm. This study provides a simple and robust chemical route to fabricate complex nanoring arrays with ultrahigh density of about one terabit per square inch.
Summary: A highly fluorescent photochromic polymer, poly‐BTFO4, was prepared. The fluorescence quantum yield of the poly‐BTFO4 was six times higher than that of BTFO4. Fatigue resistance of the polymer at its photostationary state was significantly enhanced compared with that of BTFO4. Importantly, the poly‐BTFO4 film also showed an efficient photochromism as well as strong fluorescence similar to the results in solution, which allow photoinduced fluorescence switching applicable to optical switches.
Improvement of fluorescence quantum yield and fatigue resistance. 相似文献
This communication details the successful synthesis of low polydispersity core cross‐linked star (CCS) polymers via DPE‐mediated polymerisation. We demonstrate the ability to produce poly(methyl methacrylate) and poly(acrylonitrile) CCS polymers that are currently inaccessible via the two most common non‐metal‐based controlled radical polymerisation techniques (NMP and RAFT polymerisations).
We report novel nanoporous polyimides formed from jungle‐gym‐type rigid polyimide gels by supercritical CO2 drying. By virtue of supercritical CO2 drying to avoid the collapse of nanostructure, porosity above 90 vol.‐% was achieved. We found a rich variety of nanoporous structures in the range of 50–800 nm such as crisp fragments, minute network, and highly‐connected beads. These characteristic structures were formed by the competitive progress of liquid‐liquid phase separation and crystallization induced due to the two chemical reactions of end‐crosslinking and thermal imidization during gelation.
Films of polyaniline (PANI) featuring about 80% crystallinity and characterised with strong π‐π stacking alignment parallel to the film surface have been obtained directly after the original synthesis upon simple drying of the aqueous PANI suspension. A strong anisotropy in the growth of the nano‐sized crystals produced during the synthesis results in the formation of micrometer‐length fibrils perpendicular to the film surface in the course of water evaporation. The regular intercalation of water molecules between the PANI chains seems to be crucial for their ordering throughout the synthesis and film formation.
Summary: A new NLO‐active lambda‐shaped main‐chain polyimide that comprises a two‐dimensional carbazole chromophore was synthesized. This polyimide exhibits high thermal and temporal stability. It can endure temperatures of up to 240 °C for a transient time and maintain a large SH signal at 100 °C for a long time because embedding the two‐dimensional chromophores into the polymer backbone effectively suppresses the randomization of the oriented dipole at high temperatures.
Alternating copolymers comprised of (meth)acrylates and vinyl ethers with controlled molecular weights and polydispersities were synthesized for the first time by living radical polymerization using organotellurium, stibine, and bismuthine chain transfer agents. Combining living alternating copolymerization and living radical or living cationic polymerization afforded hitherto unavailable block copolymers with controlled macromolecular structures.
The conformational transition of a single bottle‐brush polyelectrolyte with charged and neutral side chains is studied through MD simulations. Counterions are included explicitly and no additional salt is added. The structure of the polyelectrolyte and the counterion condensation are found to depend greatly on the Bjerrum length. As the Bjerrum length increases, the neutral side chains in a poor solvent can condense into clusters with variable size. Moreover, the polyelectrolyte forms globular structures at large or very small Bjerrum lengths. This transition is quite different from that in the case of a good solvent, in which there are not observable clusters and a globular structure is only formed at large Bjerrum lengths.
We have discovered a novel method to prepare a protein‐based hydrogel, that is, a ‘three‐dimensional nanostructured protein hydrogel’ (3D NPH), which is composed of loosely inter‐connected protein–polymer hybrid nanoparticles. The 3D NPH can be easily prepared by spotting a protein/polymer mixture on a substrate. Surprisingly, gold nanoparticles carrying protein molecules easily diffuse into the 3D NPH through pores and spaces. We have shown that the protein chip made by our 3D NPH method has tremendously improved sensitivity in detecting protein–protein interactions compared with that by direct protein immobilization methods.
Summary: A water‐soluble gold nanoparticle aggregate 2 was prepared by chloroauric acid and a polypseudorotaxane 1 of mono‐6‐thio‐β‐cyclodextrin with poly(propylene glycol) bis(2‐aminopropyl ether) ( ≈ 2 000) in the presence of sodium borohydride in N,N‐dimethylformamide (DMF) solution. The investigative results indicated that the gold nanoparticle aggregate 2 might act as an efficient DNA‐cleavage reagent.
A typical TEM image of gold nanoparticle aggregate 2 . 相似文献
Reactions between the ethylene groups in the backbone of conjugated polymers under UV illumination and heat treatment result in the cross‐linking of the main polymer chains. The cross‐linking leads to two simultaneous results in the polymer: excellent solvent resistance and increased bandgap. Using this reaction, three‐color polymer light‐emitting diodes (PLEDs) with a multi‐layer structure can be easily realized by a dry photo‐pattern in an active‐gas‐free environment. Multi‐layer blue devices with dramatically enhanced efficiency can also be achieved conveniently.
Poly(ethersulfone) membranes were surface modified in a one‐step procedure. For this purpose, the membranes were soaked with aqueous solutions of different low‐molecular weight molecules bearing diverse hydrophilic functionalities and subject to electron beam treatment. No catalysts, photoinitiators, organic solvents or other toxic reagents were used, and no additional synthetic or purification steps were required.
