Preparation and properties of poly(N‐isopropylacrylamide)/poly(N‐isopropylacrylamide) interpenetrating polymer networks for drug delivery

A novel poly(N‐isopropylacrylamide) (PNIPA)/PNIPA interpenetrating polymer network (IPN) was synthesized and characterized. In comparison with conventional PNIPA hydrogels, the shrinking rate of the IPN hydrogel increased when gels, swollen at 20 °C, were immersed in 50 °C water. The phase‐transition temperature of the IPN gel remained unchangeable because of the same chemical constituent in the PNIPA gel. The reswelling kinetics were slower than those of the PNIPA hydrogel because of the higher crosslinking density of the IPN hydrogel. The IPN hydrogel had better mechanical strength because of its higher crosslinking density and polymer volume fraction. The release behavior of 5‐fluorouracil (5‐Fu) from the IPN hydrogel showed that, at a lower temperature, the release of 5‐Fu was controlled by the diffusion of water molecules in the gel network. At a higher temperature, 5‐Fu inside the gel could not diffuse into the medium after a burst release caused by the release of the drug on the surface of the gel. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1249–1254, 2004     

Temperature‐Sensitive Poly(N‐isopropylacrylamide) Hydrogels with Macroporous Structure and Fast Response Rate

Macroporous temperature‐sensitive poly(N‐isopropylacrylamide) (PNIPA) hydrogels were prepared by a novel phase‐separation technique to improve the response properties. In comparison with a conventional PNIPA hydrogel prepared in water, these macroporous hydrogels, prepared by polymerization in aqueous sucrose solutions, have higher swelling ratios at temperatures below the lower critical solution temperature and exhibit much faster response rates to temperature changes.

Scanning electron microscopy image of the surface of a PNIPA hydrogel, prepared in 1.50 M aqueous sucrose solution.     

Poly(N‐isopropylacrylamide) Nanoparticle‐Incorporated PNIPAAm Hydrogels with Fast Shrinking Kinetics

Summary: Novel temperature‐responsive poly(N‐isopropylacrylamide) (PNIPAAm) nanoparticle‐containing PNIPAAm hydrogels were prepared by radical polymerization. In comparison with conventional PNIPAAm hydrogels, the PNIPAAm gels thus prepared exhibit much faster response rates as the temperature is raised above the lower critical solution temperature. The improved properties are a result of the incorporation of PNIPAAm particles, which first shrink and then generate pores for water molecules to be quickly squeezed out of the bulky PNIPAAm gels.

Schematic illustration of the shrinking process: (I) First PNIPAAm particles shrink and generate pores; (II) the bulky gels then shrink further at a rapid rate.     

A Novel Approach to Prepare Porous Poly(N‐isopropylacrylamide) Hydrogel with Superfast Shrinking Kinetics

In this study, the hydrophobic liquid template method was firstly used to prepare temperature sensitive, porous poly(N‐isopropylacrylamide) (PNIPAAm) hydrogel. During the radical polymerization, hydrophobic polydimethylsiloxane (PDMS) and surfactant sodium dodecyl sulfate (SDS) were used as liquid templates and stabilizer, respectively. After removal of the liquid templates, porous PNIPAAm hydrogel was obtained. This gel exhibited superfast shrinking properties when being transferred from below to above the lower critical solution temperature (LCST), which was ascribed to the interconnected porous structures.

     

Thermally Tunable Surface Wettability of Electrospun Fiber Mats: Polystyrene/Poly(N‐isopropylacrylamide) Blended versus Crosslinked Poly[(N‐isopropylacrylamide)‐co‐(methacrylic acid)]

This work reports on thermally tunable surface wettability of electrospun fiber mats of: polystyrene (PS)/poly(N‐isopropylacrylamide) (PNIPA) blended (bl‐PS/PNIPA) and crosslinked poly[(N‐isopropylacrylamide)‐co‐[methacrylic acid)] (PNIPAMAA) (xl‐NIPAMAA). Both the bl‐PS/PNIPA and xl‐PNIPAMAA fiber mats demonstrate reversibly switchable surface wettability, with the bl‐PS/PNIPA fiber mats approaching superhydrophobic ≥150° and superhydrophilic contact angle (CA) values at extreme temperatures. Weight loss studies carried out at 10 °C indicate that the crosslinked PNIPAMAA fiber mats had better structural integrity than the bl‐PS/PNIPA fiber mats. PNIPA surface chemistry and the Cassie–Baxter model were used to explain the mechanism behind the observed extreme wettability.

     

Dual responsive poly(N‐isopropylacrylamide) hydrogels having spironaphthoxazines as pendant groups

Stimuli responsive hydrogels (PNIPAAm‐MSp) with a thermoresponsive backbone and photochromic pendant groups were synthesized via free radical polymerization using N‐isopropylacrylamide, modified spironaphthoxazines with a polymerizable double bond (MSp) as photochromic monomer, the crosslinker N,N′‐methylenebis(acrylamide) and the initiator 2,2′‐azobis(isobutyronitrile) in dimethylsulfoxide. The polymers are dual responsive, in that poly(N‐isopropylacrylamide) (PNIPAAm) responds to temperature changes whereas the pendant spironaphthoxazines respond to light. Irradiation enhanced the water absorption of the polymers while increases in temperature decreased it. The irradiated PNIPAAm‐MSp showed best water absorption at 0 °C (Q = 3.25) while water desorbed at higher temperatures (35 °C; Q = 0.30); where Q is the amount of water absorbed by a gram of dry polymer. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3318–3325, 2009     

Molecular Dynamics Investigation of the Thermo‐Responsive Polymer Poly(N‐isopropylacrylamide)

Using molecular dynamics simulations with an OPLS force field, the lower critical solution temperature (LCST) of single‐ and multiple‐chain PNIPAM solutions in water is investigated. The sample containing ten polymer chains shows a sudden drop in size and volume at 305 K. Such an effect is absent in the single‐chain system. Large fluctuations of the physical properties of a short single‐chain prevent any clear detection of the LCST for the chosen model system, at least on the time scale of 200 ns. The results provide evidence that a critical number of PNIPAM monomer units must be present in the simulated system before MD simulations are capable to detect conformational changes unambiguously.

     

Conducting Polyaniline Confined in Semi‐Interpenetrating Networks

Conducting semi‐interpenetrating network composites with low conductivity percolation threshold were synthesized from waterborne conducting polyaniline (cPAn) and melamine‐urea resin. A perfect network of cPAn in the composite was observed by means of TEM (see Figure). The conductivity stability of cPAn in water was improved by confining the chain mobility of cPAn via in‐situ crosslinking of melamine‐urea resin. Cyclic voltammetry of the composites reveals electrochemical activities and reversibilities similarly to those of pure cPAn.     

Semi‐interpenetrating polymer networks composed of poly(N‐isopropyl acrylamide) and polyacrylamide hydrogels

Three series of semi‐interpenetrating polymer networks, based on crosslinked poly(N‐isopropyl acrylamide) (PNIPA) and 1 wt % nonionic or ionic (cationic and anionic) linear polyacrylamide (PAAm), were synthesized to improve the mechanical properties of PNIPA gels. The effect of the incorporation of linear polymers into responsive networks on the temperature‐induced transition, swelling behavior, and mechanical properties was studied. Polymer networks with four different crosslinking densities were prepared with various molar ratios (25:1 to 100:1) of the monomer (N‐isopropyl acrylamide) to the crosslinker (methylenebisacrylamide). The hydrogels were characterized by the determination of the equilibrium degree of swelling at 25 °C, the compression modulus, and the effective crosslinking density, as well as the ultimate hydrogel properties, such as the tensile strength and elongation at break. The introduction of cationic and anionic linear hydrophilic PAAm into PNIPA networks increased the rate of swelling, whereas the presence of nonionic PAAm diminished it. Transition temperatures were significantly affected by both the crosslinking density and the presence of linear PAAm in the hydrogel networks. Although anionic PAAm had the greatest influence on increasing the transition temperature, the presence of nonionic PAAm caused the highest dimensional change. Semi‐interpenetrating polymer networks reinforced with cationic and nonionic PAAm exhibited higher tensile strengths and elongations at break than PNIPA hydrogels, whereas the presence of anionic PAAm caused a reduction in the mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3987–3999, 2004     

Thermo‐Responsive Hydrogels with Nanodomains: Rapid Shrinking of a Nanogel‐Crosslinking Hydrogel of Poly(N‐isopropyl acrylamide)

Rapidly shrinking poly(N‐isopropyl acrylamide) (PNIPAM) hydrogels are prepared by crosslinking with self‐assembled nanogels that consist of cholesteryl‐ and methacryloyl‐substituted pullulan (CHPMA). The CHPMA nanogel (R_h = 26.4 nm) was used as a crosslinker for a hydrophilic nanodomain. Transmission electron microscopy images of the nanogel‐crosslinked PNIPAM hydrogel reveal a well‐defined nanoporous structure. The nanogel‐crosslinked PNIPAM hydrogel shows rapid shrinking based on its structure. The shrinking half‐time was ≈2 min, which is about 3 400 times faster than that of a PNIPAM hydrogel crosslinked by methylene(bisacrylamide).

     

Synthesis and characterization of poly(N‐isopropylacrylamide) films by photopolymerization

A novel method used for the preparation of poly(N‐isopropylacrylamide) (PNIPAAm) films of varying crosslink density under homogeneous/heterogeneous conditions is described in this paper. Photopolymerization of the N‐isopropylacrylamide (NIPAAm) monomer in water (homogeneous at ～7°C and heterogeneous at ～40°C) or a mixture of water/ethanol (50:50, heterogeneous at ～7°C) was carried out using 1‐[4‐(2‐hydroxyethoxy)‐phenyl]‐2‐hydroxy‐2‐methyl‐1‐propane‐1‐one (hydrophilic) or 2‐hydroxy‐2‐methyl propiophenone (hydrophobic) photo‐initiator. In order to investigate the effect of temperature and crosslink density, polymerization was carried out at ～7°C [below lower critical soluble temperature (LCST)] and ～40°C (above LCST) using varying amounts of N,N′‐methylene bisacrylamide (BIS) ranging from 1–4 wt%. Degree of swelling (determined by optical microscopy), phase transition temperature [determined by differential scanning calorimetry (DSC)] as well as morphology (scanning electron microscopy) were found to be dependent on solvent system (homogeneous/heterogeneous), temperature of polymerization and crosslink density. Hydrogels prepared at ～7°C using hydrophobic photo‐initiator and water/ethanol (50:50) as solvent, showed much higher degree of swelling at all levels of crosslink density as compared to hydrogel prepared at ～7°C using hydrophilic photo‐initiator and water as solvent. Hydrogels were used for patterning which may find applications in microfluidic devices. Copyright © 2006 John Wiley & Sons, Ltd.     

A Novel Benzoxazole‐Containing Poly(N‐isopropylacrylamide) Copolymer as a Multifunctional Sensing Material

We report a novel multifunctional material, poly(N‐isopropylacrylamide) (PNIPAAm) containing 2‐(2‐hydroxyphenyl)benzoxazole (HPBO), for sensing pH, zinc ion concentration, or temperature. By titration with zinc ions, a clear blue‐shifted emission with a high quantum efficiency was detected since the zinc complex prevented the nonradiative decay pathways of the HPBO moiety. The fluorescence characteristics of the copolymer were similar at various acidic or neutral conditions. However, a large blue shift on the emission maximum was exhibited under the basic condition, due to the disruption of the ESIPT process by the phenolate anion. The LCST affected the fluorescence properties significantly at the basic condition because the incompatibility between the PNIPAAm chain and phenolated HPBO moieties resulted in aggregation formation. The present study demonstrates that the new benzoxazole‐containing PINPAAm copolymer could be potentially used as multifunctional sensing material.

     

Effect of 1,4‐dioxane on synthesis of macroporous poly(N‐isopropylacrylamide) hydrogels

Thermosensitive Poly(N‐isopropylacrylamide) (PNIPA) hydrogels were synthesized by a free radical solution polymerization in three different ways. Normal hydrogels were prepared at room temperature and normal cryogels were prepared at subzero temperature. A cation surfactant dodecyl dimethyl benzyl ammonium bromide (DDBAB) was used during preparation of novel cryogels in freezing state. The response rates of normal hydrogels were very slow, whereas the rates of both normal and novel cryogels were very fast because of the macroporous structure of the cryogels. Mixed solvents which were composed of pure water and 1,4‐dioxane at various concentrations were used instead of pure water during the polymerization. The effects of the mixed solvent on morphology, swelling ratio, and deswelling/reswelling kinetics of the three kinds of hydrogels were investigated. For normal hydrogels and normal cryogels, there was no remarkable difference no matter the mixed solvent or pure water was used. However, the properties of the resulted novel cryogels were much different with the concentration of dioxane. Finally, the resulted hydrogels were used for concentrating emulsified paraffin. The different separation performance was attributed to the different structure of gel matrix. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6594–6603, 2008     

Magnetic poly(N‐isopropylacrylamide) microspheres by dispersion and inverse emulsion polymerization

The aim of this study was to develop novel thermally responsive polymer microspheres with magnetic properties. Dispersion and inverse emulsion copolymerization of N‐isopropylacrylamide (NIPAAm) and N,N′‐methylenebisacrylamide (MBAAm) was investigated in the presence of γ‐Fe₂O₃ nanoparticles. The resulting microspheres were characterized in terms of morphology, size, polydispersity, iron content, and temperature‐dependent swelling using optical microscopy, transmission electron microscopy, scanning electron microscopy, QELS, and AAS. The effects of several variables, such as the concentration of γ‐Fe₂O₃, MBAAm crosslinking agent, Span 80 surfactant, 2,2′‐azobis(2‐methyloctanenitrile) (AMON) initiator, and polymerization temperature on the properties of the microspheres were studied. Swelling and thermoresponsive behavior of the microspheres containing γ‐Fe₂O₃ nanoparticles were also investigated. The microspheres contained about 8 wt % of iron. The presence of magnetic nanoparticles and their concentration changes did not have any significant effect on the temperature sensitivity of the composites. The particles gradually shrink into an increasingly collapsed state when the temperature is raised to 40 °C since the increase in temperature weakens the hydration and PNIPAAm chains gradually become more hydrophobic, which leads to the collapse of the particles. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5884–5898, 2007     

Redox‐ and pH‐Responsive Cysteamine‐Modified Poly(aspartic acid) Showing a Reversible Sol–Gel Transition

Synthesis and characterization of a pH‐ and redox‐sensitive hydrogel of poly(aspartic acid) are reported. Reversible gelation and dissolution are achieved both in dimethylformamide and in aqueous medium via a thiol‐disulphide interconversion in the side chain of the polymers. Structural changes are confirmed by Raman microscopy and rheological measurements. Injectable aqueous solutions of thiolated poly(aspartic acid) can be converted into mechanically stable gels by oxidation, which can be useful for drug encapsulation and targeted delivery. Reduction‐facilitated release of an entrapped drug from disulphide cross‐linked hydrogels is studied.

     

Stimuli‐Responsive Semi‐Fluorinated Polymer Brushes on Porous Silica Substrates

Summary: A diblock copolymer brush consisting of poly(methyl acrylate)‐block‐poly(pentafluoropropyl acrylate) (Si/SiO₂//PMA‐b‐PPFA) was synthesized on a porous silica substrate. The brush was exposed to selective solvents, as well as thermal treatments, to induce a surface rearrangement. The rearrangement resulted in the selective loss or creation of an ultrahydrophobic layer by location of the fluoropolymer segment. This work demonstrates that surface rearrangements observed on flat surfaces can be transferred to porous substrates.

Image of a water droplet in contact with an Si/SiO₂//PMA‐b‐PPFA ultrahydrophobic polymer brush, synthesized from a porous silica substrate.     

Heterotactic‐specific radical polymerization of N‐isopropylacrylamide and phase transition behavior of aqueous solution of heterotactic poly(N‐isopropylacrylamide)

Radical polymerization of N‐isopropylacrylamide (NIPAAm) in toluene at low temperatures, in the presence of fluorinated‐alcohols, produced heterotactic polymer comprising an alternating sequence of meso and racemo dyads. The heterotacticity reached 70% in triads when polymerization was carried out at ?40 °C using nonafluoro‐tert‐butanol as the added alcohol. NMR analysis revealed that formation of a 1:1 complex of NIPAAm and fluorinated‐alcohol through C?O···H? O hydrogen bonding induces the heterotactic specificity. A mechanism for the heterotactic‐specific polymerization is proposed. Examination of the phase transition behavior of aqueous solutions of heterotactic poly(NIPAAm) revealed that the hysteresis of the phase transition between the heating and cooling cycles depended on the average length of meso dyads in poly(NIPAAm). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2539–2550, 2009     

Dextran Hydrogels Containing Poly(N‐isopropylacrylamide) as Grafts and Cross‐Linkers Exhibiting Enzymatic Regulation in a Specific Temperature Range

Summary: Specific temperature‐responsive biodegradable hydrogels were synthesized and characterized in terms of their regulation of enzymatic accessibility based on the physical properties of the temperature‐responsive polymers. The hydrogels consist of glycidyl methacrylate‐modified dextran grafted with the poly(N‐isopropylacrylamide) (PNIPAAm) homopolymer, and cross‐linked by co‐polymerization with NIPAAm and N,N‐dimethylacrylamide (DMAAm). The coil‐globule change in the grafted poly(NIPAAm) chains and only a slight dehydration of the poly(NIPAAm‐co‐DMAAm) cross‐linkers are effective in controlling the enzymatic degradation over a specific temperature range.

The thermo‐responses of the graft chains (steric hindrance) and the crosslinkers (slight deswelling of the hydrogel networks) control the enzymatic degradation of the hydrogel.