Novel C60‐Anchored Two‐Armed Poly(tert‐butyl acrylate): Synthesis and Characterization

Summary: A multistep synthetic procedure for preparing novel C₆₀‐anchored two‐armed poly(tert‐butyl acrylate) was developed. First, two‐armed poly(tert‐butyl acrylate) bearing a malonate ester core with well‐controlled molecular weight was synthesized through atom transfer radical polymerization. The effective Bingel reaction between C₆₀ and the well‐defined polymer was then carried out to yield C₆₀‐anchored polymer. GPC, ¹H NMR, and UV‐vis spectroscopy indicated that the C₆₀‐anchored polymer was a monosubstituted and ‘closed’ 6,6‐ring‐bridged methanofullerene derivative.

Schematic of a novel C₆₀‐anchored two‐armed polymer.     

Propylene Polymerization with Bis(phenoxy‐imine) Group‐4 Catalysts Using iBu3Al/Ph3CB(C6F5)4 as a Cocatalyst

The catalytic behavior of three bis(phenoxy‐imine) group‐4 transition‐metal complexes (M = Ti, Zr, Hf), with ⁱBu₃Al/Ph₃CB(C₆F₅)₄ cocatalyst systems towards propylene polymerization was investigated under atmospheric pressure at 25 °C. The Ti complex produced ultrahigh‐molecular‐weight atactic poly(propylene), whereas Zr and Hf complexes formed high‐molecular‐weight isotactic poly(propylene)s via a site‐control mechanism. The isotactic poly(propylene) obtained with the Hf complex displayed a high melting temperature of 123.8 °C.

     

Low‐Temperature Growth of Thick Polystyrene Brushes via ATRP

Summary: This contribution describes the graft polymerization of polystyrene (PS) by atom transfer radical polymerization at 50, 60, and 75 °C. Thick PS brushes were grown from initiator‐functionalized PGMA layers on silicon, and constant growth rates provide indirect evidence that the polymerizations were controlled.

Formation of polystyrene brushes at T < T_g by ATRP of styrene from α‐bromoester initiator‐functionalized poly(glycidyl methacrylate) layers.     

Predicting the Limit of Control in the ATRP Process: Results from Kinetic Simulations

Kinetic simulations are reported, where the ATRP equilibrium constant K_ATRP is varied and the rates and degree of control in different ATRP systems are evaluated. The apparent rate constant k_app increases with increasing K_ATRP, but a maximum is reached. The limit of control is passed before the maximum, i.e. when K_ATRP is increased further, apparent first‐order kinetics and well‐controlled molecular weights will no longer be obtained. The equilibrium constant at which the limit of control is reached varies linearly with the propagation rate constant. This enables the design of well controlled ATRP systems. The influence of the conversion and chain length dependence of the termination rate constant on the simulation results is discussed.

     

Preparation of a Polyethylene Latex by Catalytic Hydrogenation of a Polybuta‐1,4‐diene‐Based Dispersion

Summary: Fully linear polyethylene‐based latexes have been prepared by the hydrogenation of polybuta‐1,4‐diene dispersions. The latter were synthesized via dispersion ring‐opening metathesis polymerization of cycloocta‐1,5‐diene, and hydrogenated using RuCl₂(PPh₃)₃ as catalyst, without any further treatment. A high hydrogenation efficiency was achieved as demonstrated by different techniques including DSC, and ¹H NMR and FT‐IR spectroscopy. The hydrogenation process could be carried out without detrimental effect on particle size and colloidal stability as evidenced by optical microscopy and light scattering analysis.

Optical microscopy photograph of a polybutadiene‐based dispersion after hydrogenation. No change in size is observed.     

Synthesis of Folic Acid Functionalized PLLA‐b‐PPEGMA Nanoparticles for Cancer Cell Targeting

Poly(L ‐lactic acid)‐block‐poly(poly(ethylene glycol) monomethacrylate) (PLLA‐b‐PPEGMA) has been prepared by the ring‐opening polymerization of lactide with a double‐headed initiator, 2‐hydroxyethyl 2′‐methyl‐2′‐bromopropionate (HMBP), followed by atom transfer radical polymerization (ATRP) of poly(ethylene glycol) monomethacrylate (PEGMA). PLLA‐b‐PPEGMA nanoparticles with encapsulated Fe₃O₄ are prepared by a solvent evaporation/extraction technique, and then further functionalized with folic acid, a cancer targeting ligand. Our results show that such functionalized PLLA‐b‐PPEGMA nanoparticles have good potential as carriers for targeted drug delivery in cancer treatment.

     

A Helical Poly(macromonomer) Consisting of a Polyacetylene Main Chain and Polystyrene Side Chains

A novel helical poly(macromonomer) [poly(M‐PS): absolute = 82 800–252 000, determined by GPC/RALLS] with a polyacetylene main chain and polystyrene (PS) side chains was synthesized by the polymerization of acetylene‐terminated M‐PS [ = 2 000, / = 1.20, = 18] with an Rh catalyst. M‐PS was prepared by ATRP of styrene using the acetylene‐containing initiator 2‐bromo‐2‐methylpropionic acid (S)‐1‐methylpropargyl ester ( l ). In solutions, poly(M‐PS) exhibited an intense CD signal at 345–355 nm, indicating that it possessed a predominantly one‐handed helical conformation. Poly(M‐PS) had a stable helical conformation irrespective of solvents and temperature.

     

Multiple Vesicle Morphologies Formed from Reactive H‐Shaped Block Copolymers

Amphiphilic H‐shaped block copolymers (PTMSPMA)₂PEG(PTMSPMA)₂ with 91 ethylene glycol (EG) units and four PTMSPMA chains have been synthesized by atom transfer radical polymerization of trimethoxylsilylpropyl methacrylate (TMSPMA) at room temperature in methanol. The structure, molecular weight, and molecular weight distribution have been characterized by ¹H NMR spectroscopy and GPC traces. These H‐shaped block copolymers can self‐assemble in DMF/water, and multiple vesicle aggregates from large‐compound vesicles, to multilayer vesicles and unilamillar vesicles are formed. These morphologies can be simply controlled by variation of the chain length ratios.

     

Magnetic Molecularly Imprinted Polymer Particles Synthesized by Suspension Polymerization in Silicone Oil

Summary: Magnetic nanoparticles have been prepared by a co‐precipitation method and modified with methacryloxypropyltrimethoxysilane. Magnetic molecularly imprinted polymer particles have been prepared by suspension polymerization in silicone oil. The particles possess a high affinity to the template molecules and are rapidly separated under a magnetic field.

SEM photograph of magnetic MIP particles.     

Uniform PEO Star Polymers Synthesized in Water via Free Radical Polymerization or Atom Transfer Radical Polymerization

Amphiphilic star shaped polymers with poly(ethylene oxide) (PEO) arms and cross‐linked hydrophobic core were synthesized in water via either conventional free radical polymerization (FRP) or atom transfer radical polymerization (ATRP) techniques using a simple “arm‐first” method. In FRP, PEO based macromonomers (MM) were used as arm precursors, which were then cross‐linked by divinylbenzene (DVB) using 2,2′‐azoisobutyronitrile (AIBN). Uniform star polymers ( < 1.2) were achieved through adjustment of the ratio of PEO MM, DVB, and AIBN. While in case of ATRP, both PEO MM, and PEO based macroinitiator (MI) were used as arm precursors with ethylene glycol diacrylate as cross‐linker. Even more uniform star polymers with less contamination by low MW polymers were obtained, as compared to the products synthesized by FRP.

     

Nitroxide‐Mediated Controlled/Living Free Radical Copolymerization of Styrene and Divinylbenzene in Aqueous Miniemulsion

Summary: The nitroxide‐mediated controlled/living free radical copolymerization of styrene and divinylbenzene using a polystyrene‐TEMPO macroinitiator in aqueous miniemulsion and in bulk have been investigated. The crosslink densities were estimated based on the content of pendant vinyl groups as determined by ¹H NMR. Considerably lower crosslink densities were revealed in the miniemulsion than in the corresponding bulk system. The rate of polymerization in the miniemulsion increased with decreasing particle size, and was significantly higher than in bulk.

Crosslink density for the TEMPO‐mediated free radical copolymerization of S(1) and DVB(2) (f = 0.99, f = 0.01) at 125 °C in bulk (□) and in miniemulsions with d_n = 585 nm (○) and 53.3 nm (•).     

Iron‐Mediated ICAR ATRP of Styrene and Methyl Methacrylate in the Absence of Thermal Radical Initiator

Initiators for continuous activator regeneration in atom transfer radical polymerization (ICAR ATRP) is a new technique for conducting ATRP. ICAR ATRP has many strong advantages over normal ATRP, such as forming the reductive transition metal species in situ using oxidatively stable transition metal species and a lower amount of metal catalyst in comparison with the normal ATRP system. In this work, the iron‐mediated ICAR ATRP of styrene and methyl methacrylate are reported for the first time using oxidatively stable FeCl₃ · 6H₂O as the catalyst in the absence of any thermal radical initiator. The kinetics of the polymerizations and effect of different polymerization conditions are studied. It is found that the polymerization of styrene can be conducted well even if the amount of iron(III ) is as low as 50 ppm.

     

Preparation of Well‐Defined Poly[(ethylene oxide)‐block‐(sodium 2‐acrylamido‐2‐methyl‐1‐propane sulfonate)] Diblock Copolymers by Water‐Based Atom Transfer Radical Polymerization

Summary: Well‐defined poly[(ethylene oxide)‐block‐(sodium 2‐acrylamido‐2‐methyl‐1‐propane sulfonate)] diblock copolymers [P(EO_m‐b‐AMPS_n)], have been obtained by water‐based ATRP using α‐methoxy‐ω‐(2‐methylbromoisobutyrate) poly(ethylene oxide)s (MeO‐P[EO]_m‐BrⁱB with m ranging from 12 to 113) and CuBr · 2Bpy (Bpy for 2,2′‐bipyridyl) as macroinitiator and catalytic complex, respectively. Compared to direct polymerization in water, it has been demonstrated that the water/methanol (3:1, v/v) mixture is better suited for predicting the final number‐average molar mass from the initial monomer‐to‐macroinitiator molar ratio and achieving a quite narrow polydispersity, even at high monomer conversion ( ≈ 1.4 at 80% conversion). The effect of temperature, solvent mixture composition and addition of NaCl salt on the polymerization rate and extent of control over the copolymer molecular parameters have been highlighted as well.

     

Atom Transfer Radical Polymerization of iso‐Butyl Methacrylate in Microemulsion with Cationic and Non‐Ionic Emulsifiers

Direct atom transfer radical polymerization (ATRP) of iso‐butyl methacrylate in microemulsion has been performed successfully for the first time. ATRP was performed at 40 °C with different emulsifier systems: i) the cationic emulsifier n‐tetradecyltrimethylammonium bromide (TTAB); and ii) mixed emulsifier systems based on TTAB and the non‐ionic emulsifiers Emulgen 911 or Emulgen 931. All polymerizations proceeded in a controlled/living fashion, and the microemulsions were transparent with particle diameters less than 15 nm. The emulsifier system TTAB/Emulgen 911 exhibited better control than TTAB only. This is proposed to be caused by complex formation between Emulgen 911 in the organic phase and CuBr₂ (the deactivator), thus reducing the extent of exit of CuBr₂ to the aqueous phase. The more hydrophilic Emulgen 931 did not lead to improved control.

     

Amphiphilic Poly(4‐acryloylmorpholine)/Poly[2‐(N‐carbazolyl)ethyl acrylate] Random and Block Copolymers Synthesized by NMP

A series of random copolymers and block copolymers containing water‐soluble 4AM and fluorescent VAK are synthesized by NMP. The homopolymerizations of 4AM and VAK and 4AM/VAK random copolymerization are performed in 50 wt% DMF using 10 mol% SG1, resulting in a linear increase in versus conversion, and final polymers with narrow molecular weight distributions ( < 1.4). Reactivity ratios r_VAK = 0.64 ± 0.52 and r_4AM = 0.86 ± 0.66 are obtained for the 4AM/VAK random copolymerization. In addition, a poly(4AM) macroinitiator is used to initiate a surfactant‐free suspension polymerization of VAK. After 2.5 h, the resulting amphiphilic block copolymer has = 12.6 kg · mol^?1, = 1.48, molar composition F_VAK = 0.38 with latex particle sizes between 270 and 475 nm.

     

Hydrated Clay for Catalyst Removal in Copper Mediated Atom Transfer Radical Polymerization

A simple method has been described to remove catalyst from the copper mediated atom transfer radical polymerization (ATRP) of benzyl methacrylate and methyl methacrylate in anisole at 25 °C using hydrated natural clay (sodium montmorillonite, Na‐clay). The method consists of (1) addition of hydrated clay (Cu^I/clay ≈ 5 wt.‐%) either during or after the polymerization, (2) oxidation of catalyst complex by exposing the terminated reaction mixture in air, and (3) filtration to obtain catalyst free polymer solution. A strong coordination of CuBr‐ligand complex onto hydrated clay (10 wt.‐% < H₂O/clay < 30 wt.‐%) upon oxidation resulted in polymers with no or insignificant residual catalyst (<1.74 ppm), as determined by UV‐vis and atomic absorption spectroscopy. The recovered clay exhibited expanded intercalary layers and absence of polymer within it.

     

Stimuli‐Responsive Semi‐Fluorinated Polymer Brushes on Porous Silica Substrates

Summary: A diblock copolymer brush consisting of poly(methyl acrylate)‐block‐poly(pentafluoropropyl acrylate) (Si/SiO₂//PMA‐b‐PPFA) was synthesized on a porous silica substrate. The brush was exposed to selective solvents, as well as thermal treatments, to induce a surface rearrangement. The rearrangement resulted in the selective loss or creation of an ultrahydrophobic layer by location of the fluoropolymer segment. This work demonstrates that surface rearrangements observed on flat surfaces can be transferred to porous substrates.

Image of a water droplet in contact with an Si/SiO₂//PMA‐b‐PPFA ultrahydrophobic polymer brush, synthesized from a porous silica substrate.     

Synthesis,Characterization and Self‐Assembly of Novel Amphiphilic Block Copolymers with a Polyhedral Oligomeric Silsesquioxanes Moiety Attached at the Junction of the Two Blocks

A novel well‐defined amphiphilic block copolymer, with the polyhedral oligomeric silsesquioxane (POSS) moiety at the junction of the two blocks of polystyrene and poly(ethylene oxide) (PEO), was designed and synthesized. First, a macroinitiator containing a POSS moiety and a PEO chain was prepared and then atom transfer radical polymerization of styrene was carried out in the presence of the macroinitiator in bulk. The polymerization results show that the process bears the characteristics of controlled/living free radical polymerizations. The structure and molecular weight of the polymers were characterized by GPC, ¹H NMR, and FT‐IR spectroscopy. The self‐assembly behaviors of the polymers was investigated by TEM and SEM. It was observed that the polymers can self‐assemble into vesicles in aqueous solution.

     

Living Radical Polymerization as a Tool for the Synthesis of Polymer‐Protein/Peptide Bioconjugates

Combinations of synthetic and natural macromolecules offer a route to new functional materials. While biological and polymer chemistry may not be natural bedfellows, many researchers are focusing their attention on the benefits of combining these fields. Recent advances in living radical polymerization have provided methods to build tailor‐made macromolecular moieties using relatively simple processes. This has led to a plethora of block copolymers, end‐functional polymers and polymers with a whole range of biological recognition abilities. This review covers work carried out until late 2006 combining living radical polymerization with proteins and peptides in the rapidly‐expanding field of bioconjugation.

     

Synthesis of Silver Nanoparticles Using a Novel Graft Copolymer and Enhanced Particle Stability via a “Polymer Brush Effect”

Polymer‐encapsulated silver nanoparticles were synthesized and sterically stabilized by a new core‐shell type system consisting of poly(S‐alt‐MA)‐graft‐PMMA copolymer that acts as a scaffold for the synthesis of size confined nanoparticles. The graft copolymer is synthesized via ambient temperature ATRP using the CuBr/PMDETA catalytic system at ambient temperature. The graft copolymer is hypothesized to function as a scaffold with the anhydride part interacting strongly with the silver ions, while the PMMA graft functions as a polymer brush that stabilizes the dispersion and prevents the particle aggregation due to a ‘polymer brush effect’. UV absorption and TEM studies confirm that the synthesized silver composite particles have a core‐shell structure.